[PATCH AUTOSEL 4.19 108/192] ARM: dts: meson8b: fix the Ethernet data line signals in eth_rgmii_pins

[PATCH AUTOSEL 4.19 108/192] ARM: dts: meson8b: fix the Ethernet data line signals in eth_rgmii_pins

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 29f0023d01f063feacfc404f0446905aee4f82ee ]

According to the Odroid-C1+ schematics the Ethernet TXD1 signal is
routed to GPIOH_5 and the TXD0 signal is routed to GPIOH_6.
The public S805 datasheet shows that TXD0 can be routed to DIF_2_P and
TXD1 can be routed to DIF_2_N instead.

The pin groups eth_txd0_0 (GPIOH_6) and eth_txd0_1 (DIF_2_P) are both
configured as Ethernet TXD0 and TXD1 data lines in meson8b.dtsi. At the
same time eth_txd1_0 (GPIOH_5) and eth_txd1_1 (DIF_2_N) are configured
as TXD0 and TXD1 data lines as well.
This results in a bad Ethernet receive performance. Presumably this is
due to the eth_txd0 and eth_txd1 signal being routed to the wrong pins.
As a result of that data can only be transmitted on eth_txd2 and
eth_txd3. However, I have no scope to fully confirm this assumption.

The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
  SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
  SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit  0: eth_rxd1 (DIF_0_P)
- register 6 bit  1: eth_rxd0 (DIF_0_N)
- register 6 bit  2: eth_rx_dv (DIF_1_P)
- register 6 bit  3: eth_rx_clk (DIF_1_N)
- register 6 bit  6: eth_tx_en (DIF_3_P)
- register 6 bit  8: eth_ref_clk (DIF_3_N)
- register 6 bit  9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)

Drop the eth_txd0_1 and eth_txd1_1 groups from eth_rgmii_pins to fix the
Ethernet transmit performance on Odroid-C1. Also add the eth_rxd2 and
eth_rxd3 groups so we don't rely on the bootloader to set them up.

iperf3 statistics before this change:
- transmitting from Odroid-C1: 741 Mbits/sec (0 retries)
- receiving on Odroid-C1: 199 Mbits/sec (1713 retries)

iperf3 statistics after this change:
- transmitting from Odroid-C1: 667 Mbits/sec (0 retries)
- receiving on Odroid-C1: 750 Mbits/sec (0 retries)

Fixes: b96446541d8390 ("ARM: dts: meson8b: extend ethernet controller description")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson8b.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
index 08f7f6be7254..5b3e5c50c72f 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/meson8b.dtsi
@@ -207,9 +207,7 @@
 				groups = "eth_tx_clk",
 					 "eth_tx_en",
 					 "eth_txd1_0",
-					 "eth_txd1_1",
 					 "eth_txd0_0",
-					 "eth_txd0_1",
 					 "eth_rx_clk",
 					 "eth_rx_dv",
 					 "eth_rxd1",
@@ -218,7 +216,9 @@
 					 "eth_mdc",
 					 "eth_ref_clk",
 					 "eth_txd2",
-					 "eth_txd3";
+					 "eth_txd3",
+					 "eth_rxd3",
+					 "eth_rxd2";
 				function = "ethernet";
 			};
 		};
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH AUTOSEL 4.19 175/192] pinctrl: meson: meson8b: add the eth_rxd2 and eth_rxd3 pins

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 6daae00243e622dd3feec7965bfe421ad6dd317e ]

Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines.
Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to
rely on the bootloader to set them up correctly.

The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
  SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
  SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit  0: eth_rxd1 (DIF_0_P)
- register 6 bit  1: eth_rxd0 (DIF_0_N)
- register 6 bit  2: eth_rx_dv (DIF_1_P)
- register 6 bit  3: eth_rx_clk (DIF_1_N)
- register 6 bit  6: eth_tx_en (DIF_3_P)
- register 6 bit  8: eth_ref_clk (DIF_3_N)
- register 6 bit  9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)

All functions except eth_rxd2 and eth_rxd3 are already supported by the
pinctrl-meson8b driver.

Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/meson/pinctrl-meson8b.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/meson/pinctrl-meson8b.c b/drivers/pinctrl/meson/pinctrl-meson8b.c
index ead4beb5f55f..036124fd363c 100644
--- a/drivers/pinctrl/meson/pinctrl-meson8b.c
+++ b/drivers/pinctrl/meson/pinctrl-meson8b.c
@@ -346,6 +346,8 @@ static const unsigned int eth_rx_dv_pins[]	= { DIF_1_P };
 static const unsigned int eth_rx_clk_pins[]	= { DIF_1_N };
 static const unsigned int eth_txd0_1_pins[]	= { DIF_2_P };
 static const unsigned int eth_txd1_1_pins[]	= { DIF_2_N };
+static const unsigned int eth_rxd3_pins[]	= { DIF_2_P };
+static const unsigned int eth_rxd2_pins[]	= { DIF_2_N };
 static const unsigned int eth_tx_en_pins[]	= { DIF_3_P };
 static const unsigned int eth_ref_clk_pins[]	= { DIF_3_N };
 static const unsigned int eth_mdc_pins[]	= { DIF_4_P };
@@ -571,6 +573,8 @@ static struct meson_pmx_group meson8b_cbus_groups[] = {
 	GROUP(eth_ref_clk,	6,	8),
 	GROUP(eth_mdc,		6,	9),
 	GROUP(eth_mdio_en,	6,	10),
+	GROUP(eth_rxd3,		7,	22),
+	GROUP(eth_rxd2,		7,	23),
 };
 
 static struct meson_pmx_group meson8b_aobus_groups[] = {
@@ -720,7 +724,7 @@ static const char * const ethernet_groups[] = {
 	"eth_tx_clk", "eth_tx_en", "eth_txd1_0", "eth_txd1_1",
 	"eth_txd0_0", "eth_txd0_1", "eth_rx_clk", "eth_rx_dv",
 	"eth_rxd1", "eth_rxd0", "eth_mdio_en", "eth_mdc", "eth_ref_clk",
-	"eth_txd2", "eth_txd3"
+	"eth_txd2", "eth_txd3", "eth_rxd3", "eth_rxd2"
 };
 
 static const char * const i2c_a_groups[] = {
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH AUTOSEL 4.19 184/192] clk: meson: clean-up clock registration

[Sasha Levin]

From: Jerome Brunet <jbrunet@baylibre.com>

[ Upstream commit 8d9981efbcab066d17af4d3c85c169200f6f78df ]

Order, ids and size  between the table of regmap clocks and the onecell
data table could be different.

Set regmap pointer in all the regmap clocks before starting the
registration using the onecell data, to make sure we don't
get into an incoherent situation.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181221160239.26265-3-jbrunet@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/meson/meson-aoclk.c | 15 ++++++++++-----
 1 file changed, 10 insertions(+), 5 deletions(-)

diff --git a/drivers/clk/meson/meson-aoclk.c b/drivers/clk/meson/meson-aoclk.c
index f965845917e3..258c8d259ea1 100644
--- a/drivers/clk/meson/meson-aoclk.c
+++ b/drivers/clk/meson/meson-aoclk.c
@@ -65,15 +65,20 @@ int meson_aoclkc_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	/*
-	 * Populate regmap and register all clks
-	 */
-	for (clkid = 0; clkid < data->num_clks; clkid++) {
+	/* Populate regmap */
+	for (clkid = 0; clkid < data->num_clks; clkid++)
 		data->clks[clkid]->map = regmap;
 
+	/* Register all clks */
+	for (clkid = 0; clkid < data->hw_data->num; clkid++) {
+		if (!data->hw_data->hws[clkid])
+			continue;
+
 		ret = devm_clk_hw_register(dev, data->hw_data->hws[clkid]);
-		if (ret)
+		if (ret) {
+			dev_err(dev, "Clock registration failed\n");
 			return ret;
+		}
 	}
 
 	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic