From: Artem Lapkin <email2tema@gmail.com>
To: narmstrong@baylibre.com
Cc: jbrunet@baylibre.com, linux-arm-kernel@lists.infradead.org,
linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org,
christianshewitt@gmail.com, art@khadas.com, nick@khadas.com,
gouwa@khadas.com
Subject: [PATCH] arm64: dts: meson-sm1: add spdifin spdifout nodes
Date: Wed, 15 Dec 2021 11:02:36 +0800 [thread overview]
Message-ID: <20211215030236.340841-1-art@khadas.com> (raw)
Add spdifin spdifout nodes for Amlogic SM1 SoCs.
Signed-off-by: Artem Lapkin <art@khadas.com>
---
SPDIF IN and SPDIF OUT both tested and works fine for VIM3L (meson-sm1)
same as for VIM3 (meson-g12)
SPDIF in and SPDIF OUT both pins available via GPIO header (SPDIF_OUT PIN
13 spdif_ao_out_pins and SPDIF_IN PIN 35 - same PWM_F spdif_in_h_pins)
https://lore.kernel.org/linux-arm-kernel/1jtuhwvqxa.fsf@starbuckisacylon.baylibre.com/t/
ALSA spdifin test example
=========================
# arecord -fS16_LE -r48000 -c2 -Dplug:spdifin
# cat .asoundrc
pcm.spdifin {
type iec958
slave {
pcm "hw:0,1"
format IEC958_SUBFRAME_LE
}
}
DT sound card configs for testing
=================================
&spdifout {
pinctrl-0 = <&spdif_ao_out_pins>;
pinctrl-names = "default";
status = "okay";
};
&spdifin {
pinctrl-0 = <&spdif_in_h_pins>;
pinctrl-names = "default";
status = "okay";
};
...
spdif_dit: audio-codec-1 {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
status = "okay";
sound-name-prefix = "DIT";
};
spdif_dir: audio-codec-2 {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dir";
status = "okay";
sound-name-prefix = "DIR";
};
...
audio-routing = ...
"TODDR_B IN 3", "SPDIFIN Capture",
"SPDIFOUT IN 0", "FRDDR_A OUT 3";
...
dai-link-10 {
sound-dai = <&spdifout>;
codec-0 {
sound-dai = <&spdif_dit>;
};
};
/* spdif or toslink interface */
dai-link-11 {
sound-dai = <&spdifin>;
codec-0 {
sound-dai = <&spdif_dir>;
};
};
...
---
arch/arm64/boot/dts/amlogic/meson-sm1.dtsi | 27 ++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
index 3d8b1f4f2001..1e0adf259d61 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
@@ -356,6 +356,33 @@ tdmin_lb: audio-controller@3c0 {
status = "disabled";
};
+ spdifin: audio-controller@400 {
+ compatible = "amlogic,g12a-spdifin",
+ "amlogic,axg-spdifin";
+ reg = <0x0 0x400 0x0 0x30>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFIN";
+ interrupts = <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_SPDIFIN>,
+ <&clkc_audio AUD_CLKID_SPDIFIN_CLK>;
+ clock-names = "pclk", "refclk";
+ resets = <&clkc_audio AUD_RESET_SPDIFIN>;
+ status = "disabled";
+ };
+
+ spdifout: audio-controller@480 {
+ compatible = "amlogic,g12a-spdifout",
+ "amlogic,axg-spdifout";
+ reg = <0x0 0x480 0x0 0x50>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFOUT";
+ clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>,
+ <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>;
+ clock-names = "pclk", "mclk";
+ resets = <&clkc_audio AUD_RESET_SPDIFOUT>;
+ status = "disabled";
+ };
+
tdmout_a: audio-controller@500 {
compatible = "amlogic,sm1-tdmout";
reg = <0x0 0x500 0x0 0x40>;
--
2.25.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
next reply other threads:[~2021-12-15 3:03 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-15 3:02 Artem Lapkin [this message]
2022-01-03 15:18 ` [PATCH] arm64: dts: meson-sm1: add spdifin spdifout nodes Neil Armstrong
2022-01-03 15:35 ` Jerome Brunet
2022-01-12 8:57 ` Neil Armstrong
2022-01-12 8:28 ` Neil Armstrong
-- strict thread matches above, loose matches on Subject: below --
2021-08-11 5:09 Artem Lapkin
2021-09-02 13:31 ` Neil Armstrong
2021-09-06 9:25 ` Jerome Brunet
2021-09-06 11:56 ` Art Nikpal
2021-09-06 12:28 ` Neil Armstrong
2021-10-04 13:46 ` Jerome Brunet
2021-12-15 2:32 ` Art Nikpal
2021-12-17 9:30 ` Jerome Brunet
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211215030236.340841-1-art@khadas.com \
--to=email2tema@gmail.com \
--cc=art@khadas.com \
--cc=christianshewitt@gmail.com \
--cc=gouwa@khadas.com \
--cc=jbrunet@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=narmstrong@baylibre.com \
--cc=nick@khadas.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox