linux-amlogic.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Anand Moon <linux.amoon@gmail.com>
To: Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Neil Armstrong <neil.armstrong@linaro.org>,
	Kevin Hilman <khilman@baylibre.com>,
	Jerome Brunet <jbrunet@baylibre.com>,
	Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Anand Moon <linux.amoon@gmail.com>,
	linux-amlogic@lists.infradead.org, devicetree@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH v6 2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2
Date: Mon,  4 Dec 2023 20:14:26 +0530	[thread overview]
Message-ID: <20231204144429.45197-3-linux.amoon@gmail.com> (raw)
In-Reply-To: <20231204144429.45197-1-linux.amoon@gmail.com>

On Odroid n2/n2+ previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
V6:none
V5:none
V4:none
V3:none
V2:none
V1:none
---
 .../dts/amlogic/meson-g12b-odroid-n2.dtsi     | 36 ++++++++++++-------
 1 file changed, 24 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index 91c9769fda20..9e671444eca6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -31,6 +31,30 @@ hub_5v: regulator-hub_5v {
 		enable-active-high;
 	};
 
+	/* USB hub supports both USB 2.0 and USB 3.0 root hub */
+	usb-hub {
+		dr_mode = "host";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* 2.0 hub on port 1 */
+		hub_2_0: hub@1 {
+			compatible = "usb5e3,610";
+			reg = <1>;
+			peer-hub = <&hub_3_0>;
+			vdd-supply = <&usb_pwr_en>;
+		};
+
+		/* 3.0 hub on port 4 */
+		hub_3_0: hub@2 {
+			compatible = "usb5e3,620";
+			reg = <2>;
+			peer-hub = <&hub_2_0>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+			vdd-supply = <&vcc_5v>;
+		};
+	};
+
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "ODROID-N2";
@@ -234,18 +258,6 @@ &gpio {
 		"PIN_3",  /* GPIOX_17 */
 		"PIN_5",  /* GPIOX_18 */
 		"PIN_36"; /* GPIOX_19 */
-	/*
-	 * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub-hog {
-		gpio-hog;
-		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
 };
 
 &i2c3 {
-- 
2.42.0


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

      parent reply	other threads:[~2023-12-04 14:45 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-12-04 14:44 [PATCH v6 0/2] Use onboard usb hub reset on Odroid N2 Anand Moon
2023-12-04 14:44 ` [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub Anand Moon
2023-12-06 13:53   ` Rob Herring
2023-12-06 17:14     ` Anand Moon
2023-12-07  8:30       ` Krzysztof Kozlowski
2023-12-07 12:33         ` Anand Moon
2023-12-07 12:40           ` Krzysztof Kozlowski
2023-12-08  0:24             ` Anand Moon
2023-12-08  7:44               ` Krzysztof Kozlowski
2023-12-08 11:19                 ` Anand Moon
2023-12-08 12:17                   ` Krzysztof Kozlowski
2023-12-12  6:22                     ` Anand Moon
2023-12-12  8:40                       ` Krzysztof Kozlowski
2023-12-12 11:37                         ` Anand Moon
2023-12-12 11:52                           ` Krzysztof Kozlowski
2023-12-12 12:51                             ` Anand Moon
2023-12-12 13:09                               ` Krzysztof Kozlowski
2023-12-12 13:17                                 ` Anand Moon
2024-04-04  4:27                                   ` Anand Moon
2024-04-04  6:12                                     ` Krzysztof Kozlowski
2024-04-04  6:32                                       ` Anand Moon
2024-04-04  6:34                                         ` Anand Moon
2023-12-04 14:44 ` Anand Moon [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20231204144429.45197-3-linux.amoon@gmail.com \
    --to=linux.amoon@gmail.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=jbrunet@baylibre.com \
    --cc=khilman@baylibre.com \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=martin.blumenstingl@googlemail.com \
    --cc=neil.armstrong@linaro.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).