* [PATCH 1/2] ARM64: dts: meson-gxl-khadas-vim: Add GPIO lines names
2017-07-28 13:54 [PATCH 0/2] ARM64: dts: meson-gx: Add GPIO names for SBCs Neil Armstrong
@ 2017-07-28 13:54 ` Neil Armstrong
2017-08-01 19:56 ` Kevin Hilman
2017-07-28 13:54 ` [PATCH 2/2] ARM64: dts: meson-gxbb-nanopi-k2: " Neil Armstrong
1 sibling, 1 reply; 5+ messages in thread
From: Neil Armstrong @ 2017-07-28 13:54 UTC (permalink / raw)
To: linus-amlogic
This patch describes the GPIO lines usage on the Khadas VIM board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../dts/amlogic/meson-gxl-s905x-khadas-vim.dts | 56 ++++++++++++++++++++++
1 file changed, 56 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts
index 72c5a9f..67bc40f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts
@@ -105,6 +105,62 @@
linux,rc-map-name = "rc-geekbox";
};
+&pinctrl_aobus {
+ gpio-line-names = "UART TX",
+ "UART RX",
+ "Power Key In",
+ "J9 Header Pin35",
+ "J9 Header Pin16",
+ "J9 Header Pin15",
+ "J9 Header Pin33",
+ "IR In",
+ "HDMI CEC",
+ "SYS LED";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "",
+ "Power OFF",
+ "VCCK Enable",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI SDA", "HDMI SCL",
+ "HDMI_5V_EN", "SPDIF",
+ "J9 Header Pin37",
+ "J9 Header Pin30",
+ "J9 Header Pin29",
+ "J9 Header Pin32",
+ "J9 Header Pin31",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+ "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+ "eMMC Clk", "eMMC Reset", "eMMC CMD",
+ "", "BOOT_MODE", "", "", "eMMC Data Strobe",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+ "VCCK Regulator", "VDDEE Regulator",
+ /* Bank GPIOX */
+ "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+ "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+ "WIFI Power Enable", "WIFI WAKE HOST",
+ "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+ "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+ "Bluetooth UART TX", "Bluetooth UART RX",
+ "Bluetooth UART CTS", "Bluetooth UART RTS",
+ "WIFI 32K", "Bluetooth Enable",
+ "Bluetooth WAKE HOST",
+ /* Bank GPIOCLK */
+ "", "J9 Header Pin39",
+ /* GPIO_TEST_N */
+ "";
+};
+
&pwm_AO_ab {
status = "okay";
pinctrl-0 = <&pwm_ao_a_3_pins>, <&pwm_ao_b_pins>;
--
1.9.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH 2/2] ARM64: dts: meson-gxbb-nanopi-k2: Add GPIO lines names
2017-07-28 13:54 [PATCH 0/2] ARM64: dts: meson-gx: Add GPIO names for SBCs Neil Armstrong
2017-07-28 13:54 ` [PATCH 1/2] ARM64: dts: meson-gxl-khadas-vim: Add GPIO lines names Neil Armstrong
@ 2017-07-28 13:54 ` Neil Armstrong
2017-08-01 19:58 ` Kevin Hilman
1 sibling, 1 reply; 5+ messages in thread
From: Neil Armstrong @ 2017-07-28 13:54 UTC (permalink / raw)
To: linus-amlogic
This patch describes the GPIO lines usage on the Nanopi K2 board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 58 ++++++++++++++++++++++
1 file changed, 58 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index fa46283..9697a7a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -175,6 +175,64 @@
pinctrl-names = "default";
};
+&pinctrl_aobus {
+ gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
+ "VCCK En", "CON1 Header Pin31",
+ "I2S Header Pin6", "IR In", "I2S Header Pin7",
+ "I2S Header Pin3", "I2S Header Pin4",
+ "I2S Header Pin5", "HDMI CEC", "SYS LED";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+ "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+ "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+ "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+ "Eth PHY nRESET", "Eth PHY Intc",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
+ "CON1 Header Pin33",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+ "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+ "eMMC Reset", "eMMC CMD",
+ "", "", "", "", "eMMC DS",
+ "", "",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "",
+ "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+ "VDDEE Regulator", "VCCK Regulator",
+ /* Bank GPIOY */
+ "CON1 Header Pin7", "CON1 Header Pin11",
+ "CON1 Header Pin13", "CON1 Header Pin15",
+ "CON1 Header Pin18", "CON1 Header Pin19",
+ "CON1 Header Pin22", "CON1 Header Pin21",
+ "CON1 Header Pin24", "CON1 Header Pin23",
+ "CON1 Header Pin26", "CON1 Header Pin29",
+ "CON1 Header Pin32", "CON1 Header Pin8",
+ "CON1 Header Pin10", "CON1 Header Pin16",
+ "CON1 Header Pin12",
+ /* Bank GPIOX */
+ "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+ "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+ "WIFI Power Enable", "WIFI WAKE HOST",
+ "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+ "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+ "Bluetooth UART TX", "Bluetooth UART RX",
+ "Bluetooth UART CTS", "Bluetooth UART RTS",
+ "", "", "", "WIFI 32K", "Bluetooth Enable",
+ "Bluetooth WAKE HOST",
+ /* Bank GPIOCLK */
+ "", "CON1 Header Pin35", "", "",
+ /* GPIO_TEST_N */
+ "";
+};
+
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
--
1.9.1
^ permalink raw reply related [flat|nested] 5+ messages in thread