From mboxrd@z Thu Jan 1 00:00:00 1970 From: khilman@baylibre.com (Kevin Hilman) Date: Fri, 03 Feb 2017 10:10:27 -0800 Subject: [PATCH v2 5/9] mmc: meson-gx: improve interrupt handling In-Reply-To: <23e1aac3-5761-944a-f3ca-cb88a9e44ad8@gmail.com> (Heiner Kallweit's message of "Wed, 1 Feb 2017 07:48:58 +0100") References: <584e5061-d359-1436-05ee-3767a5a4b10f@gmail.com> <23e1aac3-5761-944a-f3ca-cb88a9e44ad8@gmail.com> Message-ID: <7hzii3uovg.fsf@baylibre.com> To: linus-amlogic@lists.infradead.org List-Id: linus-amlogic.lists.infradead.org Heiner Kallweit writes: > Disabling and immediately re-enabling interrupts in meson_mmc_request > doesn't provide a benefit. Instead enable interrupts in probe already. > And disable interrupts in remove, this was missing so far. > > Signed-off-by: Heiner Kallweit This isn't quite functionaly equivalent... > --- > v2: > - no changes > --- > drivers/mmc/host/meson-gx-mmc.c | 10 ++++------ > 1 file changed, 4 insertions(+), 6 deletions(-) > > diff --git a/drivers/mmc/host/meson-gx-mmc.c b/drivers/mmc/host/meson-gx-mmc.c > index 4ce4c640..0fba23d2 100644 > --- a/drivers/mmc/host/meson-gx-mmc.c > +++ b/drivers/mmc/host/meson-gx-mmc.c > @@ -546,11 +546,6 @@ static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) > /* Stop execution */ > writel(0, host->regs + SD_EMMC_START); > > - /* clear, ack, enable all interrupts */ > - writel(0, host->regs + SD_EMMC_IRQ_EN); > - writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS); > - writel(IRQ_EN_MASK, host->regs + SD_EMMC_IRQ_EN); > - > host->mrq = mrq; > > if (mrq->sbc) > @@ -777,8 +772,8 @@ static int meson_mmc_probe(struct platform_device *pdev) > writel(0, host->regs + SD_EMMC_START); > > /* clear, ack, enable all interrupts */ > - writel(0, host->regs + SD_EMMC_IRQ_EN); I'm not sure about this part. Without the "disable all" here... > writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS); ... this ack could cause an interrupt to fire, if one was pending based on boot firmware activity. I did notice this during driver development on some boards, which is why the "disable all" was added. That may have been an artifact of a buggy driver during development, but I left it in anyways. > + writel(IRQ_EN_MASK, host->regs + SD_EMMC_IRQ_EN); > > ret = devm_request_threaded_irq(&pdev->dev, host->irq, > meson_mmc_irq, meson_mmc_irq_thread, > @@ -816,6 +811,9 @@ static int meson_mmc_remove(struct platform_device *pdev) > if (WARN_ON(!host)) > return 0; > > + /* disable interrupts */ > + writel(0, host->regs + SD_EMMC_IRQ_EN); > + > if (host->bounce_buf) > dma_free_coherent(host->dev, host->bounce_buf_size, > host->bounce_buf, host->bounce_dma_addr); Other than the nit above, the rest of the cleanup looks fine. If you leave in the "disable all" during probe, Reviewed-by: Kevin Hilman Kevin