[PATCH v4 6/7] ARM: dts: meson8: switch to new bindings for UART nodes

[martin.blumenstingl@googlemail.com (Martin Blumenstingl)]

On Sat, Jun 10, 2017 at 12:37 AM, Martin Blumenstingl
<martin.blumenstingl@googlemail.com> wrote:
> Hi Neil,
>
> On Fri, Jun 9, 2017 at 11:49 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
>> Switch to the stable UART bindings by adding a XTAL node and using the
>> proper compatible strings.
> unfortunately this won't apply now that Kevin has merged my "ARM: dts:
> meson8: add and use the real clock controller"
> on the other hand this will make the patch easier as you can now do
> the same changes as in meson8b.dtsi
Neil, if you want you could also drop this from your series and let me
handle this (just let me know). I would even go one step further and
export the CLKID_UART0, CLKID_UART1 and CLKID_UART2 gates and pass
them as "pclk" for uart_{A,B,C}
I'll even *try* to test if this works on real hardware (my Meson8m2
board has a RTL8723BS SDIO wifi + bluetooth chip - wifi driver support
has been pretty bad so far - but I'll try to see if I can get and
messages out of the bluetooth part)
just let me know if you want me to handle this patch for you

>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>> ---
>>  arch/arm/boot/dts/meson8.dtsi | 23 +++++++++++++++++++----
>>  1 file changed, 19 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
>> index 6993077..a2ea112 100644
>> --- a/arch/arm/boot/dts/meson8.dtsi
>> +++ b/arch/arm/boot/dts/meson8.dtsi
>> @@ -83,6 +83,13 @@
>>                 };
>>         };
>>
>> +       xtal: xtal-clk {
>> +               compatible = "fixed-clock";
>> +               clock-frequency = <24000000>;
>> +               clock-output-names = "xtal";
>> +               #clock-cells = <0>;
>> +       };
>> +
>>         clk81: clk at 0 {
>>                 #clock-cells = <0>;
>>                 compatible = "fixed-clock";
>> @@ -199,17 +206,25 @@
>>  };
>>
>>  &uart_AO {
>> -       clocks = <&clk81>;
>> +       compatible = "amlogic,meson8-uart", "amlogic,meson-ao-uart";
>> +       clocks = <&xtal>, <&clk81>, <&clk81>;
>> +       clock-names = "xtal", "pclk", "baud";
>>  };
>>
>>  &uart_A {
>> -       clocks = <&clk81>;
>> +       compatible = "amlogic,meson8-uart";
>> +       clocks = <&xtal>, <&clk81>, <&clk81>;
>> +       clock-names = "xtal", "pclk", "baud";
>>  };
>>
>>  &uart_B {
>> -       clocks = <&clk81>;
>> +       compatible = "amlogic,meson8-uart";
>> +       clocks = <&xtal>, <&clk81>, <&clk81>;
>> +       clock-names = "xtal", "pclk", "baud";
>>  };
>>
>>  &uart_C {
>> -       clocks = <&clk81>;
>> +       compatible = "amlogic,meson8-uart";
>> +       clocks = <&xtal>, <&clk81>, <&clk81>;
>> +       clock-names = "xtal", "pclk", "baud";
>>  };
>> --
>> 1.9.1
>>
>>
>> _______________________________________________
>> linux-amlogic mailing list
>> linux-amlogic at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-amlogic