Re: [PATCH V7 0/6] Use CCF to describe the UART baud rate clock

From: Yu Tu <yu.tu@amlogic.com>
To: Jerome Brunet <jbrunet@baylibre.com>,
	<linux-serial@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-amlogic@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Jiri Slaby <jirislaby@kernel.org>,
	Neil Armstrong <narmstrong@baylibre.com>,
	Kevin Hilman <khilman@baylibre.com>,
	Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Subject: Re: [PATCH V7 0/6] Use CCF to describe the UART baud rate clock
Date: Tue, 1 Mar 2022 13:54:18 +0800	[thread overview]
Message-ID: <d0da38f1-72c1-d111-2d0d-2bfa2faf1a1d@amlogic.com> (raw)
In-Reply-To: <1j8rtvxnkv.fsf@starbuckisacylon.baylibre.com>

Hi Jerome,

On 2022/2/28 18:59, Jerome Brunet wrote:
> [ EXTERNAL EMAIL ]
> 
> 
> On Fri 25 Feb 2022 at 15:39, Yu Tu <yu.tu@amlogic.com> wrote:
> 
>> Using the common Clock code to describe the UART baud rate
>> clock makes it easier for the UART driver to be compatible
>> with the baud rate requirements of the UART IP on different
>> meson chips. Add Meson S4 SoC compatible.
>>
>> The test method:
>> Start the console and run the following commands in turn:
>> stty -F /dev/ttyAML0 115200 and stty -F /dev/ttyAML0 921600.
>>
>> Since most SoCs are too old, I was able to find all the platforms myself
>> such as Meson6, Meson8, Meson8b, GXL and so on. I only tested it with
>> G12A and S4.
> 
> GXL based board are still very common an easy to come by.
> I'm quite surprised that you are unable to test on this SoC family
The fact of the matter is that the S4 is our end-2020 chip, the G12A is 
five years old, and the GXL is seven years old. If you must ask for a 
test, I will report this problem to the leadership to coordinate resources.
> 
>>
>> Yu Tu (6):
>>    tty: serial: meson: Move request the register region to probe
>>    tty: serial: meson: Use devm_ioremap_resource to get register mapped
>>      memory
>>    tty: serial: meson: Describes the calculation of the UART baud rate
>>      clock using a clock frame
>>    tty: serial: meson: Make some bit of the REG5 register writable
>>    tty: serial: meson: The system stuck when you run the stty command on
>>      the console to change the baud rate
>>    tty: serial: meson: Added S4 SOC compatibility
>>
>> V6 -> V7: To solve the system stuck when you run the stty command on
>> the console to change the baud rate.
>> V5 -> V6: Change error format as discussed in the email.
>> V4 -> V5: Change error format.
>> V3 -> V4: Change CCF to describe the UART baud rate clock as discussed
>> in the email.
>> V2 -> V3: add compatible = "amlogic,meson-gx-uart". Because it must change
>> the DTS before it can be deleted
>> V1 -> V2: Use CCF to describe the UART baud rate clock.Make some changes as
>> discussed in the email
>>
>> Link:https://lore.kernel.org/linux-amlogic/20220118030911.12815-4-yu.tu@amlogic.com/
>>
>>   drivers/tty/serial/meson_uart.c | 221 ++++++++++++++++++++++----------
>>   1 file changed, 154 insertions(+), 67 deletions(-)
>>
>>
>> base-commit: a603ca60cebff8589882427a67f870ed946b3fc8
> 

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic