* Re: [RFC/CFT] Split 8250 port table (part 2)
[not found] <20050623110337.A31259@flint.arm.linux.org.uk>
@ 2005-06-27 10:42 ` Russell King
0 siblings, 0 replies; only message in thread
From: Russell King @ 2005-06-27 10:42 UTC (permalink / raw)
To: Linux Kernel List, Linux Serial List
On Thu, Jun 23, 2005 at 11:03:37AM +0100, Russell King wrote:
> Add separate files for the different 8250 ISA-based serial boards.
Ok, I've now committed this to my git tree. Here's the second part
to this.
What this change means is that you must set SERIAL_8250_NR_UARTS to
the total number of 8250-based UARTs you want to support, not the
number of _extra_ ports. Hopefully, I've correctly updated those
defconfig files which have been impacted by this change.
The only ports which remain in asm-*/serial.h are the platform specific
entries. These should really be converted by platform maintainers to
use a platform device, such as can be found in
arch/arm/mach-footbridge/isa.c
Index: arch/parisc/configs/712_defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/configs/712_defconfig (mode:100644)
+++ uncommitted/arch/parisc/configs/712_defconfig (mode:100644)
@@ -506,7 +506,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=8
+CONFIG_SERIAL_8250_NR_UARTS=17
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: arch/parisc/configs/a500_defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/configs/a500_defconfig (mode:100644)
+++ uncommitted/arch/parisc/configs/a500_defconfig (mode:100644)
@@ -662,7 +662,7 @@
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_CS=m
-CONFIG_SERIAL_8250_NR_UARTS=8
+CONFIG_SERIAL_8250_NR_UARTS=17
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: arch/parisc/configs/b180_defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/configs/b180_defconfig (mode:100644)
+++ uncommitted/arch/parisc/configs/b180_defconfig (mode:100644)
@@ -514,7 +514,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: arch/parisc/configs/c3000_defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/configs/c3000_defconfig (mode:100644)
+++ uncommitted/arch/parisc/configs/c3000_defconfig (mode:100644)
@@ -661,7 +661,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: arch/parisc/defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/defconfig (mode:100644)
+++ uncommitted/arch/parisc/defconfig (mode:100644)
@@ -517,7 +517,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: drivers/serial/8250.c
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/drivers/serial/8250.c (mode:100644)
+++ uncommitted/drivers/serial/8250.c (mode:100644)
@@ -105,7 +105,7 @@
SERIAL_PORT_DFNS /* defined in asm/serial.h */
};
-#define UART_NR (ARRAY_SIZE(old_serial_port) + CONFIG_SERIAL_8250_NR_UARTS)
+#define UART_NR CONFIG_SERIAL_8250_NR_UARTS
#ifdef CONFIG_SERIAL_8250_RSA
Index: drivers/serial/Kconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/drivers/serial/Kconfig (mode:100644)
+++ uncommitted/drivers/serial/Kconfig (mode:100644)
@@ -86,7 +86,7 @@
namespace, say Y here. If unsure, say N.
config SERIAL_8250_NR_UARTS
- int "Maximum number of non-legacy 8250/16550 serial ports"
+ int "Maximum number of 8250/16550 serial ports"
depends on SERIAL_8250
default "4"
help
Index: include/asm-alpha/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-alpha/serial.h (mode:100644)
+++ uncommitted/include/asm-alpha/serial.h (mode:100644)
@@ -22,54 +22,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#endif
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS
Index: include/asm-arm26/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-arm26/serial.h (mode:100644)
+++ uncommitted/include/asm-arm26/serial.h (mode:100644)
@@ -30,34 +30,16 @@
#if defined(CONFIG_ARCH_A5K)
/* UART CLK PORT IRQ FLAGS */
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
{ 0, BASE_BAUD, 0x3F8, 10, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 10, STD_COM_FLAGS }, /* ttyS1 */
#else
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
{ 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS1 */
#endif
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS2 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS3 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS13 */
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS
-
#endif
Index: include/asm-i386/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-i386/serial.h (mode:100644)
+++ uncommitted/include/asm-i386/serial.h (mode:100644)
@@ -22,109 +22,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-#define MCA_COM_FLAGS (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA)
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#ifdef CONFIG_MCA
-#define MCA_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS },
-#else
-#define MCA_SERIAL_PORT_DFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
- MCA_SERIAL_PORT_DFNS
-
Index: include/asm-m68k/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-m68k/serial.h (mode:100644)
+++ uncommitted/include/asm-m68k/serial.h (mode:100644)
@@ -26,54 +26,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#endif
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS
Index: include/asm-mips/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-mips/serial.h (mode:100644)
+++ uncommitted/include/asm-mips/serial.h (mode:100644)
@@ -29,32 +29,6 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#define RS_TABLE_SIZE 64
-#else
-#define RS_TABLE_SIZE
-#endif
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
#ifdef CONFIG_MACH_JAZZ
#include <asm/jazz.h>
@@ -240,66 +214,10 @@
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else /* CONFIG_SERIAL_MANY_PORTS */
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif /* CONFIG_SERIAL_MANY_PORTS */
-
#else /* CONFIG_HAVE_STD_PC_SERIAL_PORTS */
#define STD_SERIAL_PORT_DEFNS
-#define EXTRA_SERIAL_PORT_DEFNS
#endif /* CONFIG_HAVE_STD_PC_SERIAL_PORTS */
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
#ifdef CONFIG_MOMENCO_JAGUAR_ATX
/* Ordinary NS16552 duart with a 20MHz crystal. */
#define JAGUAR_ATX_UART_CLK 20000000
@@ -427,8 +345,6 @@
COBALT_SERIAL_PORT_DEFNS \
DDB5477_SERIAL_PORT_DEFNS \
EV96100_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
IP32_SERIAL_PORT_DEFNS \
ITE_SERIAL_PORT_DEFNS \
IVR_SERIAL_PORT_DEFNS \
Index: include/asm-parisc/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-parisc/serial.h (mode:100644)
+++ uncommitted/include/asm-parisc/serial.h (mode:100644)
@@ -19,18 +19,4 @@
* A500 w/ PCI serial cards: 5 + 4 * card ~= 17
*/
-#define STD_SERIAL_PORT_DEFNS \
- { 0, }, /* ttyS0 */ \
- { 0, }, /* ttyS1 */ \
- { 0, }, /* ttyS2 */ \
- { 0, }, /* ttyS3 */ \
- { 0, }, /* ttyS4 */ \
- { 0, }, /* ttyS5 */ \
- { 0, }, /* ttyS6 */ \
- { 0, }, /* ttyS7 */ \
- { 0, }, /* ttyS8 */
-
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS
-
+#define SERIAL_PORT_DFNS
Index: include/asm-ppc/pc_serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-ppc/pc_serial.h (mode:100644)
+++ uncommitted/include/asm-ppc/pc_serial.h (mode:100644)
@@ -35,93 +35,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS
Index: include/asm-sh/bigsur/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-sh/bigsur/serial.h (mode:100644)
+++ uncommitted/include/asm-sh/bigsur/serial.h (mode:100644)
@@ -14,13 +14,10 @@
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, HD64465_IRQ_UART, STD_COM_FLAGS } /* ttyS0 */
-
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
/* XXX: This should be moved ino irq.h */
#define irq_cannonicalize(x) (x)
Index: include/asm-sh/ec3104/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-sh/ec3104/serial.h (mode:100644)
+++ uncommitted/include/asm-sh/ec3104/serial.h (mode:100644)
@@ -10,13 +10,11 @@
* it's got the keyboard controller behind it so we can't really use it
* (without moving the keyboard driver to userspace, which doesn't sound
* like a very good idea) */
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x11C00, EC3104_IRQBASE+7, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x12000, EC3104_IRQBASE+8, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x12400, EC3104_IRQBASE+9, STD_COM_FLAGS }, /* ttyS2 */
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
/* XXX: This should be moved ino irq.h */
#define irq_cannonicalize(x) (x)
Index: include/asm-sh/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-sh/serial.h (mode:100644)
+++ uncommitted/include/asm-sh/serial.h (mode:100644)
@@ -29,20 +29,18 @@
#ifdef CONFIG_HD64465
#include <asm/hd64465.h>
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, HD64465_IRQ_UART, STD_COM_FLAGS } /* ttyS0 */
#else
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS } /* ttyS1 */
#endif
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
#endif
#endif /* _ASM_SERIAL_H */
Index: include/asm-sh64/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-sh64/serial.h (mode:100644)
+++ uncommitted/include/asm-sh64/serial.h (mode:100644)
@@ -20,13 +20,11 @@
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS } /* ttyS1 */
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
/* XXX: This should be moved ino irq.h */
#define irq_cannonicalize(x) (x)
Index: include/asm-x86_64/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-x86_64/serial.h (mode:100644)
+++ uncommitted/include/asm-x86_64/serial.h (mode:100644)
@@ -22,109 +22,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-#define MCA_COM_FLAGS (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA)
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#ifdef CONFIG_MCA
-#define MCA_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS },
-#else
-#define MCA_SERIAL_PORT_DFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
- MCA_SERIAL_PORT_DFNS
-
--
Russell King
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of: 2.6 Serial core
^ permalink raw reply [flat|nested] only message in thread