From mboxrd@z Thu Jan  1 00:00:00 1970
From: kgene.kim@samsung.com (Kukjin Kim)
Date: Fri, 10 Sep 2010 19:44:55 +0900
Subject: [PATCH 5/6] ARM: S5PC110: add support for otg usb gadget on Goni
	board
In-Reply-To: <1284103403-10696-6-git-send-email-m.szyprowski@samsung.com>
References: <1284103403-10696-1-git-send-email-m.szyprowski@samsung.com>
	<1284103403-10696-6-git-send-email-m.szyprowski@samsung.com>
Message-ID: <000b01cb50d5$37981140$a6c833c0$%kim@samsung.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Marek Szyprowski wrote:
> 
> Add required platform definitions for s3c-hsotg driver to enable usb
> gadget support on Samsung Goni board.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  arch/arm/mach-s5pv210/Kconfig     |    1 +
>  arch/arm/mach-s5pv210/mach-goni.c |    5 +++++
>  2 files changed, 6 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
> index b1f671d..f8bac5a 100644
> --- a/arch/arm/mach-s5pv210/Kconfig
> +++ b/arch/arm/mach-s5pv210/Kconfig
> @@ -85,6 +85,7 @@ config MACH_GONI
>  	select S3C_DEV_HSMMC2
>  	select S3C_DEV_I2C1
>  	select S5P_DEV_ONENAND
> +	select S3C_DEV_USB_HSOTG
>  	select SAMSUNG_DEV_KEYPAD
>  	select S5PV210_SETUP_FB_24BPP
>  	select S5PV210_SETUP_I2C1
> diff --git a/arch/arm/mach-s5pv210/mach-goni.c
b/arch/arm/mach-s5pv210/mach-
> goni.c
> index 30da422..b28a42b 100644
> --- a/arch/arm/mach-s5pv210/mach-goni.c
> +++ b/arch/arm/mach-s5pv210/mach-goni.c
> @@ -41,6 +41,8 @@
>  #include <plat/iic.h>
>  #include <plat/keypad.h>
>  #include <plat/sdhci.h>
> +#include <plat/clock.h>
> +#include <plat/s5p-clock.h>

Hmm...same 'extern struct clk_xusbxti' defined both.
I will sort out :-)

I think, just one inclusion is enough now.
If any problems, please let me know.

> 
>  /* Following are default values for UCON, ULCON and UFCON UART registers
*/
>  #define GONI_UCON_DEFAULT	(S3C2410_UCON_TXILEVEL |	\
> @@ -569,6 +571,7 @@ static struct platform_device *goni_devices[]
__initdata = {
>  	&s3c_device_fb,
>  	&s5p_device_onenand,
>  	&goni_spi_gpio,
> +	&s3c_device_usb_hsotg,
>  	&goni_i2c_gpio_pmic,
>  	&goni_device_gpiokeys,
>  	&s5p_device_fimc0,
> @@ -613,6 +616,8 @@ static void __init goni_machine_init(void)
>  	samsung_keypad_set_platdata(&keypad_data);
> 
>  	platform_add_devices(goni_devices, ARRAY_SIZE(goni_devices));
> +
> +	clk_xusbxti.rate = 24000000;
>  }
> 
>  MACHINE_START(GONI, "GONI")
> --


Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.