* [Patch v3] AM35xx: Craneboard: Add USB EHCI support
[not found] <[PATCH] Craneboard: Add USB EHCI Support>
@ 2010-12-01 16:58 ` srinath at mistralsolutions.com
2010-12-02 6:25 ` G, Manjunath Kondaiah
0 siblings, 1 reply; 3+ messages in thread
From: srinath at mistralsolutions.com @ 2010-12-01 16:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Srinath <srinath@mistralsolutions.com>
AM3517/05 Craneboard has one EHCI interface on board using port1.
GPIO35 is used as power enable.
GPIO38 is used as port1 PHY reset.
History:
http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%3A+Add+USB+EHCI+support&q=t
Signed-off-by: Srinath <srinath@mistralsolutions.com>
---
arch/arm/mach-omap2/board-am3517crane.c | 40 +++++++++++++++++++++++++++++++
1 files changed, 40 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 13ead33..6fd5dfe 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -28,8 +28,13 @@
#include <plat/board.h>
#include <plat/common.h>
+#include <plat/usb.h>
#include "mux.h"
+#include "control.h"
+
+#define GPIO_USB_POWER 35
+#define GPIO_USB_NRESET 38
/* Board initialization */
static struct omap_board_config_kernel am3517_crane_config[] __initdata = {
@@ -53,10 +58,45 @@ static void __init am3517_crane_init_irq(void)
omap_gpio_init();
}
+static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = GPIO_USB_NRESET,
+ .reset_gpio_port[1] = -EINVAL,
+ .reset_gpio_port[2] = -EINVAL
+};
+
static void __init am3517_crane_init(void)
{
+ int ret;
+
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap_serial_init();
+
+ /* Configure GPIO for EHCI port */
+ omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT);
+
+ ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
+ if (ret < 0) {
+ pr_err("Cannot request GPIO %d\n", GPIO_USB_POWER);
+ return;
+ }
+
+ ret = gpio_direction_output(GPIO_USB_POWER, 1);
+ if (ret < 0)
+ goto err;
+
+ omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT);
+ usb_ehci_init(&ehci_pdata);
+ return;
+
+err:
+ gpio_free(GPIO_USB_POWER);
+ pr_err("Unable to initialize EHCI power\n");
+ return;
}
MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
--
1.7.1.226.g770c5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [Patch v3] AM35xx: Craneboard: Add USB EHCI support
2010-12-01 16:58 ` [Patch v3] AM35xx: Craneboard: Add USB EHCI support srinath at mistralsolutions.com
@ 2010-12-02 6:25 ` G, Manjunath Kondaiah
2010-12-02 7:21 ` Srinath R
0 siblings, 1 reply; 3+ messages in thread
From: G, Manjunath Kondaiah @ 2010-12-02 6:25 UTC (permalink / raw)
To: linux-arm-kernel
* srinath at mistralsolutions.com <srinath@mistralsolutions.com> [2010-12-01 22:28:50 +0530]:
> From: Srinath <srinath@mistralsolutions.com>
>
> AM3517/05 Craneboard has one EHCI interface on board using port1.
>
> GPIO35 is used as power enable.
> GPIO38 is used as port1 PHY reset.
>
> History:
> http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%3A+Add+USB+EHCI+support&q=t
>
> Signed-off-by: Srinath <srinath@mistralsolutions.com>
> ---
> arch/arm/mach-omap2/board-am3517crane.c | 40 +++++++++++++++++++++++++++++++
> 1 files changed, 40 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
> index 13ead33..6fd5dfe 100644
> --- a/arch/arm/mach-omap2/board-am3517crane.c
> +++ b/arch/arm/mach-omap2/board-am3517crane.c
> @@ -28,8 +28,13 @@
>
[...]
> static void __init am3517_crane_init(void)
> {
> + int ret;
> +
> omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
> omap_serial_init();
> +
> + /* Configure GPIO for EHCI port */
> + omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT);
This is non void function. You can consider return value for further
processing.
> +
> + ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
> + if (ret < 0) {
> + pr_err("Cannot request GPIO %d\n", GPIO_USB_POWER);
> + return;
> + }
> +
> + ret = gpio_direction_output(GPIO_USB_POWER, 1);
> + if (ret < 0)
> + goto err;
> +
> + omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT);
-Ditto-
Also, why there is no gpio_request for "GPIO_USB_NRESET"
-Manjunath
[...]
^ permalink raw reply [flat|nested] 3+ messages in thread
* [Patch v3] AM35xx: Craneboard: Add USB EHCI support
2010-12-02 6:25 ` G, Manjunath Kondaiah
@ 2010-12-02 7:21 ` Srinath R
0 siblings, 0 replies; 3+ messages in thread
From: Srinath R @ 2010-12-02 7:21 UTC (permalink / raw)
To: linux-arm-kernel
Hi Manjunath,
Thanks for the review, Please find my response inline.
With Regards
Srinath
-----Original Message-----
From: G, Manjunath Kondaiah [mailto:manjugk at ti.com]
Sent: Thursday, December 02, 2010 11:56 AM
To: srinath at mistralsolutions.com
Cc: linux-omap at vger.kernel.org; jdk at ti.com; tony at atomide.com;
linux-kernel at vger.kernel.org; linux at arm.linux.org.uk;
linux-arm-kernel at lists.infradead.org; khilman at deeprootsystems.com;
nm at ti.com; nagendra at mistralsolutions.com; umeshk at mistralsolutions.com
Subject: Re: [Patch v3] AM35xx: Craneboard: Add USB EHCI support
* srinath at mistralsolutions.com <srinath@mistralsolutions.com> [2010-12-01
22:28:50 +0530]:
> From: Srinath <srinath@mistralsolutions.com>
>
> AM3517/05 Craneboard has one EHCI interface on board using port1.
>
> GPIO35 is used as power enable.
> GPIO38 is used as port1 PHY reset.
>
> History:
>
http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%3A+Add+USB+EHCI+support&
q=t
>
> Signed-off-by: Srinath <srinath@mistralsolutions.com>
> ---
> arch/arm/mach-omap2/board-am3517crane.c | 40
+++++++++++++++++++++++++++++++
> 1 files changed, 40 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-am3517crane.c
b/arch/arm/mach-omap2/board-am3517crane.c
> index 13ead33..6fd5dfe 100644
> --- a/arch/arm/mach-omap2/board-am3517crane.c
> +++ b/arch/arm/mach-omap2/board-am3517crane.c
> @@ -28,8 +28,13 @@
>
[...]
> static void __init am3517_crane_init(void)
> {
> + int ret;
> +
> omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
> omap_serial_init();
> +
> + /* Configure GPIO for EHCI port */
> + omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT);
This is non void function. You can consider return value for further
processing.
<Srinath> Sure, I will put check and resend patch
> +
> + ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
> + if (ret < 0) {
> + pr_err("Cannot request GPIO %d\n", GPIO_USB_POWER);
> + return;
> + }
> +
> + ret = gpio_direction_output(GPIO_USB_POWER, 1);
> + if (ret < 0)
> + goto err;
> +
> + omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT);
-Ditto-
<Srinath> Sure, I will put check and resend patch
Also, why there is no gpio_request for "GPIO_USB_NRESET"
<Srinath> This is taken care by USB driver in drivers/usb/host/ehci-omap.c
-Manjunath
[...]
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2010-12-02 7:21 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <[PATCH] Craneboard: Add USB EHCI Support>
2010-12-01 16:58 ` [Patch v3] AM35xx: Craneboard: Add USB EHCI support srinath at mistralsolutions.com
2010-12-02 6:25 ` G, Manjunath Kondaiah
2010-12-02 7:21 ` Srinath R
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).