* [PATCH] ARM: dts: Fix booting on Rinato market device
@ 2014-11-07 11:44 Krzysztof Kozlowski
2014-11-07 11:50 ` Chanwoo Choi
0 siblings, 1 reply; 5+ messages in thread
From: Krzysztof Kozlowski @ 2014-11-07 11:44 UTC (permalink / raw)
To: linux-arm-kernel
The bootloader on market Rinato (Gear 2) device checks for revision in
compatible field of DTB. If it is not present or lower than required
then booting fails with: "Could not do normal boot. (no DTB found)".
Log of bootloader in case of failure:
h/w: revision = 0x06
h/w: schematic = SM-R380_Rev0.5_Final_0205
date = 2000/01/01 12:00:21 (UTC)
cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720
load_kernel: loading boot image from 57344.. (BOOT)
load_kernel: found zImage, size: 0x3267e8
0xbc Error!
Verify_Binary_Signature: failed.
pit_check_signature (BOOT) invalid.
load_kernel: found custom kernel (ret:-2147483647)
No need to update kernel type.
Detected board: samsung,rinato-rev06
Could not do normal boot. (no DTB found)
: Entering usb mode for SM-R380_EUR_XX (65535)..
Add a "rev06" suffix to compatible to satisfy the bootloader.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
---
arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index 84380fa13e37..f72ba0a1d915 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -18,7 +18,8 @@
/ {
model = "Samsung Rinato board";
- compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
+ compatible = "samsung,rinato", "samsung,rinato-rev06",
+ "samsung,exynos3250", "samsung,exynos3";
aliases {
i2c7 = &i2c_max77836;
--
1.9.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH] ARM: dts: Fix booting on Rinato market device
2014-11-07 11:44 [PATCH] ARM: dts: Fix booting on Rinato market device Krzysztof Kozlowski
@ 2014-11-07 11:50 ` Chanwoo Choi
2014-11-07 11:59 ` Krzysztof Kozlowski
0 siblings, 1 reply; 5+ messages in thread
From: Chanwoo Choi @ 2014-11-07 11:50 UTC (permalink / raw)
To: linux-arm-kernel
Hi Krzysztof,
On 11/07/2014 08:44 PM, Krzysztof Kozlowski wrote:
> The bootloader on market Rinato (Gear 2) device checks for revision in
> compatible field of DTB. If it is not present or lower than required
> then booting fails with: "Could not do normal boot. (no DTB found)".
>
> Log of bootloader in case of failure:
> h/w: revision = 0x06
> h/w: schematic = SM-R380_Rev0.5_Final_0205
> date = 2000/01/01 12:00:21 (UTC)
> cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720
> load_kernel: loading boot image from 57344.. (BOOT)
> load_kernel: found zImage, size: 0x3267e8
> 0xbc Error!
> Verify_Binary_Signature: failed.
> pit_check_signature (BOOT) invalid.
> load_kernel: found custom kernel (ret:-2147483647)
> No need to update kernel type.
> Detected board: samsung,rinato-rev06
> Could not do normal boot. (no DTB found)
> : Entering usb mode for SM-R380_EUR_XX (65535)..
>
> Add a "rev06" suffix to compatible to satisfy the bootloader.
>
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
> ---
> arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
> index 84380fa13e37..f72ba0a1d915 100644
> --- a/arch/arm/boot/dts/exynos3250-rinato.dts
> +++ b/arch/arm/boot/dts/exynos3250-rinato.dts
> @@ -18,7 +18,8 @@
>
> / {
> model = "Samsung Rinato board";
> - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
> + compatible = "samsung,rinato", "samsung,rinato-rev06",
> + "samsung,exynos3250", "samsung,exynos3";
I think it is wrong. The released bootloader from Samsung is not u-boot.
Instead, you have to update u-boot to support Exynos3250-basd Rinato board.
Thanks,
Chanwoo Choi
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH] ARM: dts: Fix booting on Rinato market device
2014-11-07 11:50 ` Chanwoo Choi
@ 2014-11-07 11:59 ` Krzysztof Kozlowski
2014-11-08 10:16 ` Kukjin Kim
0 siblings, 1 reply; 5+ messages in thread
From: Krzysztof Kozlowski @ 2014-11-07 11:59 UTC (permalink / raw)
To: linux-arm-kernel
On pi?, 2014-11-07 at 20:50 +0900, Chanwoo Choi wrote:
> Hi Krzysztof,
>
> On 11/07/2014 08:44 PM, Krzysztof Kozlowski wrote:
> > The bootloader on market Rinato (Gear 2) device checks for revision in
> > compatible field of DTB. If it is not present or lower than required
> > then booting fails with: "Could not do normal boot. (no DTB found)".
> >
> > Log of bootloader in case of failure:
> > h/w: revision = 0x06
> > h/w: schematic = SM-R380_Rev0.5_Final_0205
> > date = 2000/01/01 12:00:21 (UTC)
> > cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720
> > load_kernel: loading boot image from 57344.. (BOOT)
> > load_kernel: found zImage, size: 0x3267e8
> > 0xbc Error!
> > Verify_Binary_Signature: failed.
> > pit_check_signature (BOOT) invalid.
> > load_kernel: found custom kernel (ret:-2147483647)
> > No need to update kernel type.
> > Detected board: samsung,rinato-rev06
> > Could not do normal boot. (no DTB found)
> > : Entering usb mode for SM-R380_EUR_XX (65535)..
> >
> > Add a "rev06" suffix to compatible to satisfy the bootloader.
> >
> > Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
> > ---
> > arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++-
> > 1 file changed, 2 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
> > index 84380fa13e37..f72ba0a1d915 100644
> > --- a/arch/arm/boot/dts/exynos3250-rinato.dts
> > +++ b/arch/arm/boot/dts/exynos3250-rinato.dts
> > @@ -18,7 +18,8 @@
> >
> > / {
> > model = "Samsung Rinato board";
> > - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
> > + compatible = "samsung,rinato", "samsung,rinato-rev06",
> > + "samsung,exynos3250", "samsung,exynos3";
>
> I think it is wrong. The released bootloader from Samsung is not u-boot.
> Instead, you have to update u-boot to support Exynos3250-basd Rinato board.
The bootloader on device also was not a u-boot. So the fix is for native
bootloader delivered on device.
I do not insist that this is proper fix. It was just needed to boot the
device with custom kernel.
Anyway, thanks for comments!
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH] ARM: dts: Fix booting on Rinato market device
2014-11-07 11:59 ` Krzysztof Kozlowski
@ 2014-11-08 10:16 ` Kukjin Kim
2014-11-10 1:03 ` Chanwoo Choi
0 siblings, 1 reply; 5+ messages in thread
From: Kukjin Kim @ 2014-11-08 10:16 UTC (permalink / raw)
To: linux-arm-kernel
Krzysztof Kozlowski wrote:
>
> On pi?, 2014-11-07 at 20:50 +0900, Chanwoo Choi wrote:
> > Hi Krzysztof,
> >
> > On 11/07/2014 08:44 PM, Krzysztof Kozlowski wrote:
> > > The bootloader on market Rinato (Gear 2) device checks for revision in
> > > compatible field of DTB. If it is not present or lower than required
> > > then booting fails with: "Could not do normal boot. (no DTB found)".
> > >
> > > Log of bootloader in case of failure:
> > > h/w: revision = 0x06
> > > h/w: schematic = SM-R380_Rev0.5_Final_0205
> > > date = 2000/01/01 12:00:21 (UTC)
> > > cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720
> > > load_kernel: loading boot image from 57344.. (BOOT)
> > > load_kernel: found zImage, size: 0x3267e8
> > > 0xbc Error!
> > > Verify_Binary_Signature: failed.
> > > pit_check_signature (BOOT) invalid.
> > > load_kernel: found custom kernel (ret:-2147483647)
> > > No need to update kernel type.
> > > Detected board: samsung,rinato-rev06
> > > Could not do normal boot. (no DTB found)
> > > : Entering usb mode for SM-R380_EUR_XX (65535)..
> > >
> > > Add a "rev06" suffix to compatible to satisfy the bootloader.
> > >
> > > Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
> > > ---
> > > arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++-
> > > 1 file changed, 2 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
> > > index 84380fa13e37..f72ba0a1d915 100644
> > > --- a/arch/arm/boot/dts/exynos3250-rinato.dts
> > > +++ b/arch/arm/boot/dts/exynos3250-rinato.dts
> > > @@ -18,7 +18,8 @@
> > >
> > > / {
> > > model = "Samsung Rinato board";
> > > - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
> > > + compatible = "samsung,rinato", "samsung,rinato-rev06",
> > > + "samsung,exynos3250", "samsung,exynos3";
> >
> > I think it is wrong. The released bootloader from Samsung is not u-boot.
> > Instead, you have to update u-boot to support Exynos3250-basd Rinato board.
>
> The bootloader on device also was not a u-boot. So the fix is for native
> bootloader delivered on device.
>
> I do not insist that this is proper fix. It was just needed to boot the
> device with custom kernel.
>
> Anyway, thanks for comments!
>
Hi Krzysztof and Chanwoo,
So, we don?t need this to fix the problem Krzysztof said? OK.
- Kukjin
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH] ARM: dts: Fix booting on Rinato market device
2014-11-08 10:16 ` Kukjin Kim
@ 2014-11-10 1:03 ` Chanwoo Choi
0 siblings, 0 replies; 5+ messages in thread
From: Chanwoo Choi @ 2014-11-10 1:03 UTC (permalink / raw)
To: linux-arm-kernel
Dear Kukjin,
On 11/08/2014 07:16 PM, Kukjin Kim wrote:
> Krzysztof Kozlowski wrote:
>>
>> On pi?, 2014-11-07 at 20:50 +0900, Chanwoo Choi wrote:
>>> Hi Krzysztof,
>>>
>>> On 11/07/2014 08:44 PM, Krzysztof Kozlowski wrote:
>>>> The bootloader on market Rinato (Gear 2) device checks for revision in
>>>> compatible field of DTB. If it is not present or lower than required
>>>> then booting fails with: "Could not do normal boot. (no DTB found)".
>>>>
>>>> Log of bootloader in case of failure:
>>>> h/w: revision = 0x06
>>>> h/w: schematic = SM-R380_Rev0.5_Final_0205
>>>> date = 2000/01/01 12:00:21 (UTC)
>>>> cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720
>>>> load_kernel: loading boot image from 57344.. (BOOT)
>>>> load_kernel: found zImage, size: 0x3267e8
>>>> 0xbc Error!
>>>> Verify_Binary_Signature: failed.
>>>> pit_check_signature (BOOT) invalid.
>>>> load_kernel: found custom kernel (ret:-2147483647)
>>>> No need to update kernel type.
>>>> Detected board: samsung,rinato-rev06
>>>> Could not do normal boot. (no DTB found)
>>>> : Entering usb mode for SM-R380_EUR_XX (65535)..
>>>>
>>>> Add a "rev06" suffix to compatible to satisfy the bootloader.
>>>>
>>>> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
>>>> ---
>>>> arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++-
>>>> 1 file changed, 2 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
>>>> index 84380fa13e37..f72ba0a1d915 100644
>>>> --- a/arch/arm/boot/dts/exynos3250-rinato.dts
>>>> +++ b/arch/arm/boot/dts/exynos3250-rinato.dts
>>>> @@ -18,7 +18,8 @@
>>>>
>>>> / {
>>>> model = "Samsung Rinato board";
>>>> - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
>>>> + compatible = "samsung,rinato", "samsung,rinato-rev06",
>>>> + "samsung,exynos3250", "samsung,exynos3";
>>>
>>> I think it is wrong. The released bootloader from Samsung is not u-boot.
>>> Instead, you have to update u-boot to support Exynos3250-basd Rinato board.
>>
>> The bootloader on device also was not a u-boot. So the fix is for native
>> bootloader delivered on device.
>>
>> I do not insist that this is proper fix. It was just needed to boot the
>> device with custom kernel.
>>
>> Anyway, thanks for comments!
>>
> Hi Krzysztof and Chanwoo,
>
> So, we don?t need this to fix the problem Krzysztof said? OK.
Yes.
The released bootloader from Samsung is not general and not opened.
We have to support Exynos3250-based Rinato on general bootloader.
Beset Regards,
Chanwoo Choi
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2014-11-10 1:03 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-11-07 11:44 [PATCH] ARM: dts: Fix booting on Rinato market device Krzysztof Kozlowski
2014-11-07 11:50 ` Chanwoo Choi
2014-11-07 11:59 ` Krzysztof Kozlowski
2014-11-08 10:16 ` Kukjin Kim
2014-11-10 1:03 ` Chanwoo Choi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).