[PATCHv2 3/7] ARM: S5PC110: add support for S6E63M0 LCD controller on Goni board

[kgene.kim@samsung.com (Kukjin Kim)]

Marek Szyprowski wrote:
> 
> Add required platform definitions for S6E63M0 LCD controller on Samsung
> Goni board.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  arch/arm/mach-s5pv210/mach-goni.c |   71
> +++++++++++++++++++++++++++++++++++++
>  1 files changed, 71 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-s5pv210/mach-goni.c
b/arch/arm/mach-s5pv210/mach-
> goni.c
> index b0ae208..b263f3a 100644
> --- a/arch/arm/mach-s5pv210/mach-goni.c
> +++ b/arch/arm/mach-s5pv210/mach-goni.c
> @@ -16,6 +16,9 @@
>  #include <linux/i2c.h>
>  #include <linux/i2c-gpio.h>
>  #include <linux/mfd/max8998.h>
> +#include <linux/spi/spi.h>
> +#include <linux/spi/spi_gpio.h>
> +#include <linux/lcd.h>
>  #include <linux/gpio_keys.h>
>  #include <linux/input.h>
>  #include <linux/gpio.h>
> @@ -111,6 +114,70 @@ static struct s3c_fb_platdata goni_lcd_pdata
__initdata =
> {
>  	.setup_gpio	= s5pv210_fb_gpio_setup_24bpp,
>  };
> 
> +static int lcd_power_on(struct lcd_device *ld, int enable)
> +{
> +	return 1;

Always 1?

> +}
> +
> +static int reset_lcd(struct lcd_device *ld)
> +{
> +	static unsigned int first = 1;
> +	int reset_gpio = -1;
> +
> +	reset_gpio = S5PV210_MP05(5);
> +
> +	if (first) {
> +		gpio_request(reset_gpio, "MLCD_RST");
> +		first = 0;
> +	}
> +
> +	gpio_direction_output(reset_gpio, 1);
> +	return 1;
> +}

Hmm...
Could you please explain about the functionality of above reset_lcd()?

> +
> +static struct lcd_platform_data s6e63m0_platform_data = {
> +	.reset			= reset_lcd,
> +	.power_on		= lcd_power_on,
> +	.lcd_enabled		= 0,
> +
> +	.reset_delay		= 120,	/* 120ms */
> +	.power_on_delay		= 25,	/* 25ms */
> +	.power_off_delay	= 200,	/* 200ms */
> +};
> +
> +#define LCD_BUS_NUM	3
> +#define DISPLAY_CS	S5PV210_MP01(1)
> +static struct spi_board_info spi_board_info[] __initdata = {
> +	{
> +		.modalias	= "s6e63m0",
> +		.platform_data	= (void *)&s6e63m0_platform_data,
                                  ^^^^^^^^
No need.

> +		.max_speed_hz	= 1200000,
> +		.bus_num	= LCD_BUS_NUM,
> +		.chip_select	= 0,
> +		.mode		= SPI_MODE_3,
> +		.controller_data = (void *)DISPLAY_CS,



> +	},
> +};
> +
> +#define DISPLAY_CLK	S5PV210_MP04(1)
> +#define DISPLAY_SI	S5PV210_MP04(3)
> +static struct spi_gpio_platform_data lcd_spi_gpio_data = {
> +	.sck	= DISPLAY_CLK,
> +	.mosi	= DISPLAY_SI,

How about use the S5PV210_MPXX directly with comment?

> +	.miso	= SPI_GPIO_NO_MISO,
> +
> +	.num_chipselect	= 1,
> +};
> +
> +static struct platform_device goni_spi_gpio = {
> +	.name	= "spi_gpio",
> +	.id	= LCD_BUS_NUM,
> +	.dev	= {
> +		.parent		= &s3c_device_fb.dev,
> +		.platform_data	= &lcd_spi_gpio_data,
> +	},
> +};
> +
>  /* KEYPAD */
>  static uint32_t keymap[] __initdata = {
>  	/* KEY(row, col, keycode) */
> @@ -479,6 +546,7 @@ static void goni_setup_sdhci(void)
>  static struct platform_device *goni_devices[] __initdata = {
>  	&s3c_device_fb,
>  	&s5p_device_onenand,
> +	&goni_spi_gpio,
>  	&goni_i2c_gpio_pmic,
>  	&goni_device_gpiokeys,
>  	&s5p_device_fimc0,
> @@ -509,6 +577,9 @@ static void __init goni_machine_init(void)
>  	/* FB */
>  	s3c_fb_set_platdata(&goni_lcd_pdata);
> 
> +	/* SPI */
> +	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
> +
>  	/* KEYPAD */
>  	samsung_keypad_set_platdata(&keypad_data);
> 
> --


Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.