From mboxrd@z Thu Jan  1 00:00:00 1970
From: kgene.kim@samsung.com (Kukjin Kim)
Date: Thu, 15 Sep 2011 14:52:18 +0900
Subject: [PATCH] arm: exynos4: fix incorrect pad configuration for keypad
	row lines
In-Reply-To: <1315129244-26489-1-git-send-email-thomas.abraham@linaro.org>
References: <1315129244-26489-1-git-send-email-thomas.abraham@linaro.org>
Message-ID: <00a201cc736b$a11dc740$e35955c0$%kim@samsung.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Thomas Abraham wrote:
> 
> The keypad controller requires a external pull-up for all the keypad
> row lines. Fix the incorrect pad configuration for keypad controller
> row lines by enabling the pad pull-up for the all row lines of the
> keypad controller.
> 
> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
> ---
> SMDKV310 board does not have pull-up resistors populated for the keypad
> row lines (unlike the smdk boards for the previous Samsung SoC's). So
> the pad pull-up for all keypad row lines should be enabled for
> smdkv310 board.
> 
> The default requirement for the keypad controller is to enable the
> pull-up for all the keypad row lines. If a exynos4 based board has
> on-board pull-up's populated for keypad row lines, this patch would
> cause no harm. And in such cases, if internal pad pull-up is to be
> disabled (to reduce some power consumption), an alternative gpio
> configuration function can be supplied that does not enable the
> internal pad pull-up.
> ---
>  arch/arm/mach-exynos4/setup-keypad.c |   11 ++++++-----
>  1 files changed, 6 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/mach-exynos4/setup-keypad.c b/arch/arm/mach-
> exynos4/setup-keypad.c
> index 1ee0ebf..7862bfb 100644
> --- a/arch/arm/mach-exynos4/setup-keypad.c
> +++ b/arch/arm/mach-exynos4/setup-keypad.c
> @@ -19,15 +19,16 @@ void samsung_keypad_cfg_gpio(unsigned int rows,
> unsigned int cols)
> 
>  	if (rows > 8) {
>  		/* Set all the necessary GPX2 pins: KP_ROW[0~7] */
> -		s3c_gpio_cfgrange_nopull(EXYNOS4_GPX2(0), 8,
> S3C_GPIO_SFN(3));
> +		s3c_gpio_cfgall_range(EXYNOS4_GPX2(0), 8,
> S3C_GPIO_SFN(3),
> +					S3C_GPIO_PULL_UP);
> 
>  		/* Set all the necessary GPX3 pins: KP_ROW[8~] */
> -		s3c_gpio_cfgrange_nopull(EXYNOS4_GPX3(0), (rows - 8),
> -					 S3C_GPIO_SFN(3));
> +		s3c_gpio_cfgall_range(EXYNOS4_GPX3(0), (rows - 8),
> +					 S3C_GPIO_SFN(3),
> S3C_GPIO_PULL_UP);
>  	} else {
>  		/* Set all the necessary GPX2 pins: KP_ROW[x] */
> -		s3c_gpio_cfgrange_nopull(EXYNOS4_GPX2(0), rows,
> -					 S3C_GPIO_SFN(3));
> +		s3c_gpio_cfgall_range(EXYNOS4_GPX2(0), rows,
> S3C_GPIO_SFN(3),
> +					S3C_GPIO_PULL_UP);
>  	}
> 
>  	/* Set all the necessary GPX1 pins to special-function 3: KP_COL[x]
*/
> --
> 1.6.6.rc2

Oops, you're right, applied.
Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.