[PATCH v8 0/7] Enable L2 cache support on Exynos4210/4x12 SoCs

[PATCH v8 0/7] Enable L2 cache support on Exynos4210/4x12 SoCs

[Marek Szyprowski]

This is an updated patchset, which intends to add support for L2 cache
on Exynos4 SoCs on boards running under secure firmware, which requires
certain initialization steps to be done with help of firmware, as
selected registers are writable only from secure mode.

First four patches extend existing support for secure write in L2C driver
to account for design of secure firmware running on Exynos. Namely:
 1) direct read access to certain registers is needed on Exynos, because
    secure firmware calls set several registers at once,
 2) not all boards are running secure firmware, so .write_sec callback
    needs to be installed in Exynos firmware ops initialization code,
 3) write access to {DATA,TAG}_LATENCY_CTRL registers fron non-secure world
    is not allowed and so must use l2c_write_sec as well,
 4) on certain boards, default value of prefetch register is incorrect
    and must be overridden at L2C initialization.
For boards running with firmware that provides access to individual
L2C registers this series should introduce no functional changes. However
since the driver is widely used on other platforms I'd like to kindly ask
any interested people for testing.

Further three patches add implementation of .write_sec and .configure
callbacks for Exynos secure firmware and necessary DT nodes to enable
L2 cache.

Changes in this version tested on Exynos4412-based TRATS2 and OdroidU3+
boards (both with secure firmware). There should be no functional change
for Exynos boards running without secure firmware. I do not have access
to affected non-Exynos boards, so I could not test on them.


Depends on:
 - [PATCH v3 0/5] Firmware-assisted suspend/resume of Exynos SoCs
   (https://lkml.org/lkml/2014/8/26/445)
   available in samsung/pm2 branch in
   git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git
 - L2C patches merged to v3.18-rc3


Changelog:
Changes since v7:
(https://lkml.org/lkml/2014/10/29/158)
- rebased onto arm-soc/for-next kernel tree (depends on patches merged to
  v3.18-rc3 and arm-soc/samsung/pm2 branch)
- removed 'ARM: l2c: unify L2C-310 OF initialization error messages' patch
  (no longer needed)

Changes since v6:
(https://lkml.org/lkml/2014/10/27/233)
- changed PL310 to L2C-310 prefix in error messages
- added patch shortening the error message about incorrect associativity

Changes since v5:
(https://lkml.org/lkml/2014/9/24/364)
- rebased onto v3.18-rc2
- added error message about missing properties values

Changes since v4:
(https://lkml.org/lkml/2014/8/26/461)
 - rewrote the code accessing l2x0_saved_regs from assembly code
 - added comment and reworked unconditional call to SMC_CMD_L2X0INVALL


Patch summary:

Tomasz Figa (7):
  ARM: l2c: Refactor the driver to use commit-like interface
  ARM: l2c: Add interface to ask hypervisor to configure L2C
  ARM: l2c: Get outer cache .write_sec callback from mach_desc only if
    not NULL
  ARM: l2c: Add support for overriding prefetch settings
  ARM: EXYNOS: Add .write_sec outer cache callback for L2C-310
  ARM: EXYNOS: Add support for non-secure L2X0 resume
  ARM: dts: exynos4: Add nodes for L2 cache controller

 Documentation/devicetree/bindings/arm/l2cc.txt |  10 +
 arch/arm/boot/dts/exynos4210.dtsi              |   9 +
 arch/arm/boot/dts/exynos4x12.dtsi              |  14 ++
 arch/arm/include/asm/outercache.h              |   3 +
 arch/arm/kernel/irq.c                          |   3 +-
 arch/arm/mach-exynos/firmware.c                |  50 +++++
 arch/arm/mach-exynos/sleep.S                   |  46 +++++
 arch/arm/mm/cache-l2x0.c                       | 270 ++++++++++++++++---------
 8 files changed, 309 insertions(+), 96 deletions(-)

-- 
1.9.2

[PATCH v8 1/7] ARM: l2c: Refactor the driver to use commit-like interface

[Marek Szyprowski]

From: Tomasz Figa <t.figa@samsung.com>

Certain implementations of secure hypervisors (namely the one found on
Samsung Exynos-based boards) do not provide access to individual L2C
registers. This makes the .write_sec()-based interface insufficient and
provoking ugly hacks.

This patch is first step to make the driver not rely on availability of
writes to individual registers. This is achieved by refactoring the
driver to use a commit-like operation scheme: all register values are
prepared first and stored in an instance of l2x0_regs struct and then a
single callback is responsible to flush those values to the hardware.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/mm/cache-l2x0.c | 210 ++++++++++++++++++++++++++---------------------
 1 file changed, 115 insertions(+), 95 deletions(-)

diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index 5e65ca8dea62..e5948c5adaa7 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -41,12 +41,14 @@ struct l2c_init_data {
 	void (*enable)(void __iomem *, u32, unsigned);
 	void (*fixup)(void __iomem *, u32, struct outer_cache_fns *);
 	void (*save)(void __iomem *);
+	void (*configure)(void __iomem *);
 	struct outer_cache_fns outer_cache;
 };
 
 #define CACHE_LINE_SIZE		32
 
 static void __iomem *l2x0_base;
+static const struct l2c_init_data *l2x0_data;
 static DEFINE_RAW_SPINLOCK(l2x0_lock);
 static u32 l2x0_way_mask;	/* Bitmask of active ways */
 static u32 l2x0_size;
@@ -106,6 +108,14 @@ static inline void l2c_unlock(void __iomem *base, unsigned num)
 	}
 }
 
+static void l2c_configure(void __iomem *base)
+{
+	if (l2x0_data->configure)
+		l2x0_data->configure(base);
+
+	l2c_write_sec(l2x0_saved_regs.aux_ctrl, base, L2X0_AUX_CTRL);
+}
+
 /*
  * Enable the L2 cache controller.  This function must only be
  * called when the cache controller is known to be disabled.
@@ -114,7 +124,12 @@ static void l2c_enable(void __iomem *base, u32 aux, unsigned num_lock)
 {
 	unsigned long flags;
 
-	l2c_write_sec(aux, base, L2X0_AUX_CTRL);
+	/* Do not touch the controller if already enabled. */
+	if (readl_relaxed(base + L2X0_CTRL) & L2X0_CTRL_EN)
+		return;
+
+	l2x0_saved_regs.aux_ctrl = aux;
+	l2c_configure(base);
 
 	l2c_unlock(base, num_lock);
 
@@ -208,6 +223,11 @@ static void l2c_save(void __iomem *base)
 	l2x0_saved_regs.aux_ctrl = readl_relaxed(l2x0_base + L2X0_AUX_CTRL);
 }
 
+static void l2c_resume(void)
+{
+	l2c_enable(l2x0_base, l2x0_saved_regs.aux_ctrl, l2x0_data->num_lock);
+}
+
 /*
  * L2C-210 specific code.
  *
@@ -288,14 +308,6 @@ static void l2c210_sync(void)
 	__l2c210_cache_sync(l2x0_base);
 }
 
-static void l2c210_resume(void)
-{
-	void __iomem *base = l2x0_base;
-
-	if (!(readl_relaxed(base + L2X0_CTRL) & L2X0_CTRL_EN))
-		l2c_enable(base, l2x0_saved_regs.aux_ctrl, 1);
-}
-
 static const struct l2c_init_data l2c210_data __initconst = {
 	.type = "L2C-210",
 	.way_size_0 = SZ_8K,
@@ -309,7 +321,7 @@ static const struct l2c_init_data l2c210_data __initconst = {
 		.flush_all = l2c210_flush_all,
 		.disable = l2c_disable,
 		.sync = l2c210_sync,
-		.resume = l2c210_resume,
+		.resume = l2c_resume,
 	},
 };
 
@@ -466,7 +478,7 @@ static const struct l2c_init_data l2c220_data = {
 		.flush_all = l2c220_flush_all,
 		.disable = l2c_disable,
 		.sync = l2c220_sync,
-		.resume = l2c210_resume,
+		.resume = l2c_resume,
 	},
 };
 
@@ -615,39 +627,29 @@ static void __init l2c310_save(void __iomem *base)
 							L310_POWER_CTRL);
 }
 
-static void l2c310_resume(void)
+static void l2c310_configure(void __iomem *base)
 {
-	void __iomem *base = l2x0_base;
+	unsigned revision;
 
-	if (!(readl_relaxed(base + L2X0_CTRL) & L2X0_CTRL_EN)) {
-		unsigned revision;
-
-		/* restore pl310 setup */
-		writel_relaxed(l2x0_saved_regs.tag_latency,
-			       base + L310_TAG_LATENCY_CTRL);
-		writel_relaxed(l2x0_saved_regs.data_latency,
-			       base + L310_DATA_LATENCY_CTRL);
-		writel_relaxed(l2x0_saved_regs.filter_end,
-			       base + L310_ADDR_FILTER_END);
-		writel_relaxed(l2x0_saved_regs.filter_start,
-			       base + L310_ADDR_FILTER_START);
-
-		revision = readl_relaxed(base + L2X0_CACHE_ID) &
-				L2X0_CACHE_ID_RTL_MASK;
-
-		if (revision >= L310_CACHE_ID_RTL_R2P0)
-			l2c_write_sec(l2x0_saved_regs.prefetch_ctrl, base,
-				      L310_PREFETCH_CTRL);
-		if (revision >= L310_CACHE_ID_RTL_R3P0)
-			l2c_write_sec(l2x0_saved_regs.pwr_ctrl, base,
-				      L310_POWER_CTRL);
-
-		l2c_enable(base, l2x0_saved_regs.aux_ctrl, 8);
-
-		/* Re-enable full-line-of-zeros for Cortex-A9 */
-		if (l2x0_saved_regs.aux_ctrl & L310_AUX_CTRL_FULL_LINE_ZERO)
-			set_auxcr(get_auxcr() | BIT(3) | BIT(2) | BIT(1));
-	}
+	/* restore pl310 setup */
+	writel_relaxed(l2x0_saved_regs.tag_latency,
+		       base + L310_TAG_LATENCY_CTRL);
+	writel_relaxed(l2x0_saved_regs.data_latency,
+		       base + L310_DATA_LATENCY_CTRL);
+	writel_relaxed(l2x0_saved_regs.filter_end,
+		       base + L310_ADDR_FILTER_END);
+	writel_relaxed(l2x0_saved_regs.filter_start,
+		       base + L310_ADDR_FILTER_START);
+
+	revision = readl_relaxed(base + L2X0_CACHE_ID) &
+				 L2X0_CACHE_ID_RTL_MASK;
+
+	if (revision >= L310_CACHE_ID_RTL_R2P0)
+		l2c_write_sec(l2x0_saved_regs.prefetch_ctrl, base,
+			      L310_PREFETCH_CTRL);
+	if (revision >= L310_CACHE_ID_RTL_R3P0)
+		l2c_write_sec(l2x0_saved_regs.pwr_ctrl, base,
+			      L310_POWER_CTRL);
 }
 
 static int l2c310_cpu_enable_flz(struct notifier_block *nb, unsigned long act, void *data)
@@ -699,6 +701,23 @@ static void __init l2c310_enable(void __iomem *base, u32 aux, unsigned num_lock)
 		aux &= ~(L310_AUX_CTRL_FULL_LINE_ZERO | L310_AUX_CTRL_EARLY_BRESP);
 	}
 
+	/* r3p0 or later has power control register */
+	if (rev >= L310_CACHE_ID_RTL_R3P0)
+		l2x0_saved_regs.pwr_ctrl = L310_DYNAMIC_CLK_GATING_EN |
+						L310_STNDBY_MODE_EN;
+
+	/*
+	 * Always enable non-secure access to the lockdown registers -
+	 * we write to them as part of the L2C enable sequence so they
+	 * need to be accessible.
+	 */
+	aux |= L310_AUX_CTRL_NS_LOCKDOWN;
+
+	l2c_enable(base, aux, num_lock);
+
+	/* Read back resulting AUX_CTRL value as it could have been altered. */
+	aux = readl_relaxed(base + L2X0_AUX_CTRL);
+
 	if (aux & (L310_AUX_CTRL_DATA_PREFETCH | L310_AUX_CTRL_INSTR_PREFETCH)) {
 		u32 prefetch = readl_relaxed(base + L310_PREFETCH_CTRL);
 
@@ -712,23 +731,12 @@ static void __init l2c310_enable(void __iomem *base, u32 aux, unsigned num_lock)
 	if (rev >= L310_CACHE_ID_RTL_R3P0) {
 		u32 power_ctrl;
 
-		l2c_write_sec(L310_DYNAMIC_CLK_GATING_EN | L310_STNDBY_MODE_EN,
-			      base, L310_POWER_CTRL);
 		power_ctrl = readl_relaxed(base + L310_POWER_CTRL);
 		pr_info("L2C-310 dynamic clock gating %sabled, standby mode %sabled\n",
 			power_ctrl & L310_DYNAMIC_CLK_GATING_EN ? "en" : "dis",
 			power_ctrl & L310_STNDBY_MODE_EN ? "en" : "dis");
 	}
 
-	/*
-	 * Always enable non-secure access to the lockdown registers -
-	 * we write to them as part of the L2C enable sequence so they
-	 * need to be accessible.
-	 */
-	aux |= L310_AUX_CTRL_NS_LOCKDOWN;
-
-	l2c_enable(base, aux, num_lock);
-
 	if (aux & L310_AUX_CTRL_FULL_LINE_ZERO) {
 		set_auxcr(get_auxcr() | BIT(3) | BIT(2) | BIT(1));
 		cpu_notifier(l2c310_cpu_enable_flz, 0);
@@ -760,11 +768,11 @@ static void __init l2c310_fixup(void __iomem *base, u32 cache_id,
 
 	if (revision >= L310_CACHE_ID_RTL_R3P0 &&
 	    revision < L310_CACHE_ID_RTL_R3P2) {
-		u32 val = readl_relaxed(base + L310_PREFETCH_CTRL);
+		u32 val = l2x0_saved_regs.prefetch_ctrl;
 		/* I don't think bit23 is required here... but iMX6 does so */
 		if (val & (BIT(30) | BIT(23))) {
 			val &= ~(BIT(30) | BIT(23));
-			l2c_write_sec(val, base, L310_PREFETCH_CTRL);
+			l2x0_saved_regs.prefetch_ctrl = val;
 			errata[n++] = "752271";
 		}
 	}
@@ -800,6 +808,15 @@ static void l2c310_disable(void)
 	l2c_disable();
 }
 
+static void l2c310_resume(void)
+{
+	l2c_resume();
+
+	/* Re-enable full-line-of-zeros for Cortex-A9 */
+	if (l2x0_saved_regs.aux_ctrl & L310_AUX_CTRL_FULL_LINE_ZERO)
+		set_auxcr(get_auxcr() | BIT(3) | BIT(2) | BIT(1));
+}
+
 static const struct l2c_init_data l2c310_init_fns __initconst = {
 	.type = "L2C-310",
 	.way_size_0 = SZ_8K,
@@ -807,6 +824,7 @@ static const struct l2c_init_data l2c310_init_fns __initconst = {
 	.enable = l2c310_enable,
 	.fixup = l2c310_fixup,
 	.save = l2c310_save,
+	.configure = l2c310_configure,
 	.outer_cache = {
 		.inv_range = l2c210_inv_range,
 		.clean_range = l2c210_clean_range,
@@ -818,7 +836,7 @@ static const struct l2c_init_data l2c310_init_fns __initconst = {
 	},
 };
 
-static void __init __l2c_init(const struct l2c_init_data *data,
+static int __init __l2c_init(const struct l2c_init_data *data,
 	u32 aux_val, u32 aux_mask, u32 cache_id)
 {
 	struct outer_cache_fns fns;
@@ -826,6 +844,14 @@ static void __init __l2c_init(const struct l2c_init_data *data,
 	u32 aux, old_aux;
 
 	/*
+	 * Save the pointer globally so that callbacks which do not receive
+	 * context from callers can access the structure.
+	 */
+	l2x0_data = kmemdup(data, sizeof(*data), GFP_KERNEL);
+	if (!l2x0_data)
+		return -ENOMEM;
+
+	/*
 	 * Sanity check the aux values.  aux_mask is the bits we preserve
 	 * from reading the hardware register, and aux_val is the bits we
 	 * set.
@@ -910,6 +936,8 @@ static void __init __l2c_init(const struct l2c_init_data *data,
 		data->type, ways, l2x0_size >> 10);
 	pr_info("%s: CACHE_ID 0x%08x, AUX_CTRL 0x%08x\n",
 		data->type, cache_id, aux);
+
+	return 0;
 }
 
 void __init l2x0_init(void __iomem *base, u32 aux_val, u32 aux_mask)
@@ -936,6 +964,10 @@ void __init l2x0_init(void __iomem *base, u32 aux_val, u32 aux_mask)
 		break;
 	}
 
+	/* Read back current (default) hardware configuration */
+	if (data->save)
+		data->save(l2x0_base);
+
 	__l2c_init(data, aux_val, aux_mask, cache_id);
 }
 
@@ -1102,7 +1134,7 @@ static const struct l2c_init_data of_l2c210_data __initconst = {
 		.flush_all   = l2c210_flush_all,
 		.disable     = l2c_disable,
 		.sync        = l2c210_sync,
-		.resume      = l2c210_resume,
+		.resume      = l2c_resume,
 	},
 };
 
@@ -1120,7 +1152,7 @@ static const struct l2c_init_data of_l2c220_data __initconst = {
 		.flush_all   = l2c220_flush_all,
 		.disable     = l2c_disable,
 		.sync        = l2c220_sync,
-		.resume      = l2c210_resume,
+		.resume      = l2c_resume,
 	},
 };
 
@@ -1135,28 +1167,26 @@ static void __init l2c310_of_parse(const struct device_node *np,
 
 	of_property_read_u32_array(np, "arm,tag-latency", tag, ARRAY_SIZE(tag));
 	if (tag[0] && tag[1] && tag[2])
-		writel_relaxed(
+		l2x0_saved_regs.tag_latency =
 			L310_LATENCY_CTRL_RD(tag[0] - 1) |
 			L310_LATENCY_CTRL_WR(tag[1] - 1) |
-			L310_LATENCY_CTRL_SETUP(tag[2] - 1),
-			l2x0_base + L310_TAG_LATENCY_CTRL);
+			L310_LATENCY_CTRL_SETUP(tag[2] - 1);
 
 	of_property_read_u32_array(np, "arm,data-latency",
 				   data, ARRAY_SIZE(data));
 	if (data[0] && data[1] && data[2])
-		writel_relaxed(
+		l2x0_saved_regs.data_latency =
 			L310_LATENCY_CTRL_RD(data[0] - 1) |
 			L310_LATENCY_CTRL_WR(data[1] - 1) |
-			L310_LATENCY_CTRL_SETUP(data[2] - 1),
-			l2x0_base + L310_DATA_LATENCY_CTRL);
+			L310_LATENCY_CTRL_SETUP(data[2] - 1);
 
 	of_property_read_u32_array(np, "arm,filter-ranges",
 				   filter, ARRAY_SIZE(filter));
 	if (filter[1]) {
-		writel_relaxed(ALIGN(filter[0] + filter[1], SZ_1M),
-			       l2x0_base + L310_ADDR_FILTER_END);
-		writel_relaxed((filter[0] & ~(SZ_1M - 1)) | L310_ADDR_FILTER_EN,
-			       l2x0_base + L310_ADDR_FILTER_START);
+		l2x0_saved_regs.filter_end =
+					ALIGN(filter[0] + filter[1], SZ_1M);
+		l2x0_saved_regs.filter_start = (filter[0] & ~(SZ_1M - 1))
+					| L310_ADDR_FILTER_EN;
 	}
 
 	ret = l2x0_cache_size_of_parse(np, aux_val, aux_mask, &assoc, SZ_512K);
@@ -1188,6 +1218,7 @@ static const struct l2c_init_data of_l2c310_data __initconst = {
 	.enable = l2c310_enable,
 	.fixup = l2c310_fixup,
 	.save  = l2c310_save,
+	.configure = l2c310_configure,
 	.outer_cache = {
 		.inv_range   = l2c210_inv_range,
 		.clean_range = l2c210_clean_range,
@@ -1216,6 +1247,7 @@ static const struct l2c_init_data of_l2c310_coherent_data __initconst = {
 	.enable = l2c310_enable,
 	.fixup = l2c310_fixup,
 	.save  = l2c310_save,
+	.configure = l2c310_configure,
 	.outer_cache = {
 		.inv_range   = l2c210_inv_range,
 		.clean_range = l2c210_clean_range,
@@ -1330,16 +1362,6 @@ static void aurora_save(void __iomem *base)
 	l2x0_saved_regs.aux_ctrl = readl_relaxed(base + L2X0_AUX_CTRL);
 }
 
-static void aurora_resume(void)
-{
-	void __iomem *base = l2x0_base;
-
-	if (!(readl(base + L2X0_CTRL) & L2X0_CTRL_EN)) {
-		writel_relaxed(l2x0_saved_regs.aux_ctrl, base + L2X0_AUX_CTRL);
-		writel_relaxed(l2x0_saved_regs.ctrl, base + L2X0_CTRL);
-	}
-}
-
 /*
  * For Aurora cache in no outer mode, enable via the CP15 coprocessor
  * broadcasting of cache commands to L2.
@@ -1401,7 +1423,7 @@ static const struct l2c_init_data of_aurora_with_outer_data __initconst = {
 		.flush_all   = l2x0_flush_all,
 		.disable     = l2x0_disable,
 		.sync        = l2x0_cache_sync,
-		.resume      = aurora_resume,
+		.resume      = l2c_resume,
 	},
 };
 
@@ -1414,7 +1436,7 @@ static const struct l2c_init_data of_aurora_no_outer_data __initconst = {
 	.fixup = aurora_fixup,
 	.save  = aurora_save,
 	.outer_cache = {
-		.resume      = aurora_resume,
+		.resume      = l2c_resume,
 	},
 };
 
@@ -1562,6 +1584,7 @@ static const struct l2c_init_data of_bcm_l2x0_data __initconst = {
 	.of_parse = l2c310_of_parse,
 	.enable = l2c310_enable,
 	.save  = l2c310_save,
+	.configure = l2c310_configure,
 	.outer_cache = {
 		.inv_range   = bcm_inv_range,
 		.clean_range = bcm_clean_range,
@@ -1583,18 +1606,12 @@ static void __init tauros3_save(void __iomem *base)
 		readl_relaxed(base + L310_PREFETCH_CTRL);
 }
 
-static void tauros3_resume(void)
+static void tauros3_configure(void __iomem *base)
 {
-	void __iomem *base = l2x0_base;
-
-	if (!(readl_relaxed(base + L2X0_CTRL) & L2X0_CTRL_EN)) {
-		writel_relaxed(l2x0_saved_regs.aux2_ctrl,
-			       base + TAUROS3_AUX2_CTRL);
-		writel_relaxed(l2x0_saved_regs.prefetch_ctrl,
-			       base + L310_PREFETCH_CTRL);
-
-		l2c_enable(base, l2x0_saved_regs.aux_ctrl, 8);
-	}
+	writel_relaxed(l2x0_saved_regs.aux2_ctrl,
+		       base + TAUROS3_AUX2_CTRL);
+	writel_relaxed(l2x0_saved_regs.prefetch_ctrl,
+		       base + L310_PREFETCH_CTRL);
 }
 
 static const struct l2c_init_data of_tauros3_data __initconst = {
@@ -1603,9 +1620,10 @@ static const struct l2c_init_data of_tauros3_data __initconst = {
 	.num_lock = 8,
 	.enable = l2c_enable,
 	.save  = tauros3_save,
+	.configure = tauros3_configure,
 	/* Tauros3 broadcasts L1 cache operations to L2 */
 	.outer_cache = {
-		.resume      = tauros3_resume,
+		.resume      = l2c_resume,
 	},
 };
 
@@ -1661,6 +1679,10 @@ int __init l2x0_of_init(u32 aux_val, u32 aux_mask)
 	if (!of_property_read_bool(np, "cache-unified"))
 		pr_err("L2C: device tree omits to specify unified cache\n");
 
+	/* Read back current (default) hardware configuration */
+	if (data->save)
+		data->save(l2x0_base);
+
 	/* L2 configuration can only be changed if the cache is disabled */
 	if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & L2X0_CTRL_EN))
 		if (data->of_parse)
@@ -1671,8 +1693,6 @@ int __init l2x0_of_init(u32 aux_val, u32 aux_mask)
 	else
 		cache_id = readl_relaxed(l2x0_base + L2X0_CACHE_ID);
 
-	__l2c_init(data, aux_val, aux_mask, cache_id);
-
-	return 0;
+	return __l2c_init(data, aux_val, aux_mask, cache_id);
 }
 #endif
-- 
1.9.2

[PATCH v8 2/7] ARM: l2c: Add interface to ask hypervisor to configure L2C

[Marek Szyprowski]

From: Tomasz Figa <t.figa@samsung.com>

Because certain secure hypervisor do not allow writes to individual L2C
registers, but rather expect set of parameters to be passed as argument
to secure monitor calls, there is a need to provide an interface for the
L2C driver to ask the firmware to configure the hardware according to
specified parameters. This patch adds such.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/include/asm/outercache.h | 3 +++
 arch/arm/mm/cache-l2x0.c          | 6 ++++++
 2 files changed, 9 insertions(+)

diff --git a/arch/arm/include/asm/outercache.h b/arch/arm/include/asm/outercache.h
index 891a56b35bcf..563b92fc2f41 100644
--- a/arch/arm/include/asm/outercache.h
+++ b/arch/arm/include/asm/outercache.h
@@ -23,6 +23,8 @@
 
 #include <linux/types.h>
 
+struct l2x0_regs;
+
 struct outer_cache_fns {
 	void (*inv_range)(unsigned long, unsigned long);
 	void (*clean_range)(unsigned long, unsigned long);
@@ -36,6 +38,7 @@ struct outer_cache_fns {
 
 	/* This is an ARM L2C thing */
 	void (*write_sec)(unsigned long, unsigned);
+	void (*configure)(const struct l2x0_regs *);
 };
 
 extern struct outer_cache_fns outer_cache;
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index e5948c5adaa7..d214be207517 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -110,6 +110,11 @@ static inline void l2c_unlock(void __iomem *base, unsigned num)
 
 static void l2c_configure(void __iomem *base)
 {
+	if (outer_cache.configure) {
+		outer_cache.configure(&l2x0_saved_regs);
+		return;
+	}
+
 	if (l2x0_data->configure)
 		l2x0_data->configure(base);
 
@@ -910,6 +915,7 @@ static int __init __l2c_init(const struct l2c_init_data *data,
 
 	fns = data->outer_cache;
 	fns.write_sec = outer_cache.write_sec;
+	fns.configure = outer_cache.configure;
 	if (data->fixup)
 		data->fixup(l2x0_base, cache_id, &fns);
 
-- 
1.9.2

[PATCH v8 3/7] ARM: l2c: Get outer cache .write_sec callback from mach_desc only if not NULL

[Marek Szyprowski]

From: Tomasz Figa <t.figa@samsung.com>

Certain platforms (i.e. Exynos) might need to set .write_sec callback
from firmware initialization which is happenning in .init_early callback
of machine descriptor. However current code will overwrite the pointer
with whatever is present in machine descriptor, even though it can be
already set earlier. This patch fixes this by making the assignment
conditional, depending on whether current .write_sec callback is NULL.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/kernel/irq.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c
index 7c81ec428b9b..5acb8aef6f2d 100644
--- a/arch/arm/kernel/irq.c
+++ b/arch/arm/kernel/irq.c
@@ -108,7 +108,8 @@ void __init init_IRQ(void)
 
 	if (IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_CACHE_L2X0) &&
 	    (machine_desc->l2c_aux_mask || machine_desc->l2c_aux_val)) {
-		outer_cache.write_sec = machine_desc->l2c_write_sec;
+		if (!outer_cache.write_sec)
+			outer_cache.write_sec = machine_desc->l2c_write_sec;
 		ret = l2x0_of_init(machine_desc->l2c_aux_val,
 				   machine_desc->l2c_aux_mask);
 		if (ret)
-- 
1.9.2

[PATCH v8 4/7] ARM: l2c: Add support for overriding prefetch settings

[Marek Szyprowski]

From: Tomasz Figa <t.figa@samsung.com>

Firmware on certain boards (e.g. ODROID-U3) can leave incorrect L2C prefetch
settings configured in registers leading to crashes if L2C is enabled
without overriding them. This patch introduces bindings to enable
prefetch settings to be specified from DT and necessary support in the
driver.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[mszyprow: rebased onto v3.18-rc1, added error message when prefetch related
 dt property has been provided without any value]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 Documentation/devicetree/bindings/arm/l2cc.txt | 10 +++++
 arch/arm/mm/cache-l2x0.c                       | 54 ++++++++++++++++++++++++++
 2 files changed, 64 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
index 292ef7ca3058..0dbabe9a6b0a 100644
--- a/Documentation/devicetree/bindings/arm/l2cc.txt
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -57,6 +57,16 @@ Optional properties:
 - cache-id-part: cache id part number to be used if it is not present
   on hardware
 - wt-override: If present then L2 is forced to Write through mode
+- arm,double-linefill : Override double linefill enable setting. Enable if
+  non-zero, disable if zero.
+- arm,double-linefill-incr : Override double linefill on INCR read. Enable
+  if non-zero, disable if zero.
+- arm,double-linefill-wrap : Override double linefill on WRAP read. Enable
+  if non-zero, disable if zero.
+- arm,prefetch-drop : Override prefetch drop enable setting. Enable if non-zero,
+  disable if zero.
+- arm,prefetch-offset : Override prefetch offset value. Valid values are
+  0-7, 15, 23, and 31.
 
 Example:
 
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index d214be207517..6f9d5a02d053 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -1169,6 +1169,8 @@ static void __init l2c310_of_parse(const struct device_node *np,
 	u32 tag[3] = { 0, 0, 0 };
 	u32 filter[2] = { 0, 0 };
 	u32 assoc;
+	u32 prefetch;
+	u32 val;
 	int ret;
 
 	of_property_read_u32_array(np, "arm,tag-latency", tag, ARRAY_SIZE(tag));
@@ -1214,6 +1216,58 @@ static void __init l2c310_of_parse(const struct device_node *np,
 		       assoc);
 		break;
 	}
+
+	prefetch = l2x0_saved_regs.prefetch_ctrl;
+
+	ret = of_property_read_u32(np, "arm,double-linefill", &val);
+	if (ret == 0) {
+		if (val)
+			prefetch |= L310_PREFETCH_CTRL_DBL_LINEFILL;
+		else
+			prefetch &= ~L310_PREFETCH_CTRL_DBL_LINEFILL;
+	} else if (ret != -EINVAL) {
+		pr_err("L2C-310 OF arm,double-linefill property value is missing\n");
+	}
+
+	ret = of_property_read_u32(np, "arm,double-linefill-incr", &val);
+	if (ret == 0) {
+		if (val)
+			prefetch |= L310_PREFETCH_CTRL_DBL_LINEFILL_INCR;
+		else
+			prefetch &= ~L310_PREFETCH_CTRL_DBL_LINEFILL_INCR;
+	} else if (ret != -EINVAL) {
+		pr_err("L2C-310 OF arm,double-linefill-incr property value is missing\n");
+	}
+
+	ret = of_property_read_u32(np, "arm,double-linefill-wrap", &val);
+	if (ret == 0) {
+		if (!val)
+			prefetch |= L310_PREFETCH_CTRL_DBL_LINEFILL_WRAP;
+		else
+			prefetch &= ~L310_PREFETCH_CTRL_DBL_LINEFILL_WRAP;
+	} else if (ret != -EINVAL) {
+		pr_err("L2C-310 OF arm,double-linefill-wrap property value is missing\n");
+	}
+
+	ret = of_property_read_u32(np, "arm,prefetch-drop", &val);
+	if (ret == 0) {
+		if (val)
+			prefetch |= L310_PREFETCH_CTRL_PREFETCH_DROP;
+		else
+			prefetch &= ~L310_PREFETCH_CTRL_PREFETCH_DROP;
+	} else if (ret != -EINVAL) {
+		pr_err("L2C-310 OF arm,prefetch-drop property value is missing\n");
+	}
+
+	ret = of_property_read_u32(np, "arm,prefetch-offset", &val);
+	if (ret == 0) {
+		prefetch &= ~L310_PREFETCH_CTRL_OFFSET_MASK;
+		prefetch |= val & L310_PREFETCH_CTRL_OFFSET_MASK;
+	} else if (ret != -EINVAL) {
+		pr_err("L2C-310 OF arm,prefetch-offset property value is missing\n");
+	}
+
+	l2x0_saved_regs.prefetch_ctrl = prefetch;
 }
 
 static const struct l2c_init_data of_l2c310_data __initconst = {
-- 
1.9.2

[PATCH v8 5/7] ARM: EXYNOS: Add .write_sec outer cache callback for L2C-310

[Marek Szyprowski]

From: Tomasz Figa <t.figa@samsung.com>

Exynos4 SoCs equipped with an L2C-310 cache controller and running under
secure firmware require certain registers of aforementioned IP to be
accessed only from secure mode. This means that SMC calls are required
for certain register writes. To handle this, an implementation of
.write_sec and .configure callbacks is provided by this patch.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[added comment and reworked unconditional call to SMC_CMD_L2X0INVALL]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/mach-exynos/firmware.c | 50 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm/mach-exynos/firmware.c b/arch/arm/mach-exynos/firmware.c
index 766f57d2f029..dc5ae53aa317 100644
--- a/arch/arm/mach-exynos/firmware.c
+++ b/arch/arm/mach-exynos/firmware.c
@@ -17,6 +17,7 @@
 #include <asm/cacheflush.h>
 #include <asm/cputype.h>
 #include <asm/firmware.h>
+#include <asm/hardware/cache-l2x0.h>
 #include <asm/suspend.h>
 
 #include <mach/map.h>
@@ -136,6 +137,43 @@ static const struct firmware_ops exynos_firmware_ops = {
 	.resume			= IS_ENABLED(CONFIG_EXYNOS_CPU_SUSPEND) ? exynos_resume : NULL,
 };
 
+static void exynos_l2_write_sec(unsigned long val, unsigned reg)
+{
+	static int l2cache_enabled;
+
+	switch (reg) {
+	case L2X0_CTRL:
+		if (val & L2X0_CTRL_EN) {
+			/*
+			 * Before the cache can be enabled, due to firmware
+			 * design, SMC_CMD_L2X0INVALL must be called.
+			 */
+			if (!l2cache_enabled) {
+				exynos_smc(SMC_CMD_L2X0INVALL, 0, 0, 0);
+				l2cache_enabled = 1;
+			}
+		} else {
+			l2cache_enabled = 0;
+		}
+		exynos_smc(SMC_CMD_L2X0CTRL, val, 0, 0);
+		break;
+
+	case L2X0_DEBUG_CTRL:
+		exynos_smc(SMC_CMD_L2X0DEBUG, val, 0, 0);
+		break;
+
+	default:
+		WARN_ONCE(1, "%s: ignoring write to reg 0x%x\n", __func__, reg);
+	}
+}
+
+static void exynos_l2_configure(const struct l2x0_regs *regs)
+{
+	exynos_smc(SMC_CMD_L2X0SETUP1, regs->tag_latency, regs->data_latency,
+			regs->prefetch_ctrl);
+	exynos_smc(SMC_CMD_L2X0SETUP2, regs->pwr_ctrl, regs->aux_ctrl, 0);
+}
+
 void __init exynos_firmware_init(void)
 {
 	struct device_node *nd;
@@ -155,4 +193,16 @@ void __init exynos_firmware_init(void)
 	pr_info("Running under secure firmware.\n");
 
 	register_firmware_ops(&exynos_firmware_ops);
+
+	/*
+	 * Exynos 4 SoCs (based on Cortex A9 and equipped with L2C-310),
+	 * running under secure firmware, require certain registers of L2
+	 * cache controller to be written in secure mode. Here .write_sec
+	 * callback is provided to perform necessary SMC calls.
+	 */
+	if (IS_ENABLED(CONFIG_CACHE_L2X0)
+	    && read_cpuid_part() == ARM_CPU_PART_CORTEX_A9) {
+		outer_cache.write_sec = exynos_l2_write_sec;
+		outer_cache.configure = exynos_l2_configure;
+	}
 }
-- 
1.9.2

[PATCH v8 6/7] ARM: EXYNOS: Add support for non-secure L2X0 resume

[Marek Szyprowski]

From: Tomasz Figa <t.figa@samsung.com>

On Exynos SoCs it is necessary to resume operation of L2C early in
assembly code, because otherwise certain systems will crash. This patch
adds necessary code to non-secure resume handler.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[rewrote the code accessing l2x0_saved_regs]
Sigend-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/mach-exynos/sleep.S | 46 ++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 46 insertions(+)

diff --git a/arch/arm/mach-exynos/sleep.S b/arch/arm/mach-exynos/sleep.S
index e3c373082bbe..31d25834b9c4 100644
--- a/arch/arm/mach-exynos/sleep.S
+++ b/arch/arm/mach-exynos/sleep.S
@@ -16,6 +16,8 @@
  */
 
 #include <linux/linkage.h>
+#include <asm/asm-offsets.h>
+#include <asm/hardware/cache-l2x0.h>
 #include "smc.h"
 
 #define CPU_MASK	0xff0ffff0
@@ -74,6 +76,45 @@ ENTRY(exynos_cpu_resume_ns)
 	mov	r0, #SMC_CMD_C15RESUME
 	dsb
 	smc	#0
+#ifdef CONFIG_CACHE_L2X0
+	adr	r0, 1f
+	ldr	r2, [r0]
+	add	r0, r2, r0
+
+	/* Check that the address has been initialised. */
+	ldr	r1, [r0, #L2X0_R_PHY_BASE]
+	teq	r1, #0
+	beq	skip_l2x0
+
+	/* Check if controller has been enabled. */
+	ldr	r2, [r1, #L2X0_CTRL]
+	tst	r2, #0x1
+	bne	skip_l2x0
+
+	ldr	r1, [r0, #L2X0_R_TAG_LATENCY]
+	ldr	r2, [r0, #L2X0_R_DATA_LATENCY]
+	ldr	r3, [r0, #L2X0_R_PREFETCH_CTRL]
+	mov	r0, #SMC_CMD_L2X0SETUP1
+	smc	#0
+
+	/* Reload saved regs pointer because smc corrupts registers. */
+	adr	r0, 1f
+	ldr	r2, [r0]
+	add	r0, r2, r0
+
+	ldr	r1, [r0, #L2X0_R_PWR_CTRL]
+	ldr	r2, [r0, #L2X0_R_AUX_CTRL]
+	mov	r0, #SMC_CMD_L2X0SETUP2
+	smc	#0
+
+	mov	r0, #SMC_CMD_L2X0INVALL
+	smc	#0
+
+	mov	r1, #1
+	mov	r0, #SMC_CMD_L2X0CTRL
+	smc	#0
+skip_l2x0:
+#endif /* CONFIG_CACHE_L2X0 */
 skip_cp15:
 	b	cpu_resume
 ENDPROC(exynos_cpu_resume_ns)
@@ -83,3 +124,8 @@ cp15_save_diag:
 	.globl cp15_save_power
 cp15_save_power:
 	.long	0	@ cp15 power control
+
+#ifdef CONFIG_CACHE_L2X0
+	.align
+1:	.long	l2x0_saved_regs - .
+#endif /* CONFIG_CACHE_L2X0 */
-- 
1.9.2

[PATCH v8 7/7] ARM: dts: exynos4: Add nodes for L2 cache controller

[Marek Szyprowski]

From: Tomasz Figa <t.figa@samsung.com>

This patch adds device tree nodes for L2 cache controller present on
Exynos4 SoCs.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/boot/dts/exynos4210.dtsi |  9 +++++++++
 arch/arm/boot/dts/exynos4x12.dtsi | 14 ++++++++++++++
 2 files changed, 23 insertions(+)

diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index bcc9e63c8070..8e45ea44317e 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -81,6 +81,15 @@
 		reg = <0x10023CA0 0x20>;
 	};
 
+	l2c: l2-cache-controller at 10502000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x10502000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+		arm,tag-latency = <2 2 1>;
+		arm,data-latency = <2 2 1>;
+	};
+
 	gic: interrupt-controller at 10490000 {
 		cpu-offset = <0x8000>;
 	};
diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index 861bb919f6d3..c7adfd60ad3a 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -54,6 +54,20 @@
 		reg = <0x10023CA0 0x20>;
 	};
 
+	l2c: l2-cache-controller at 10502000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x10502000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+		arm,tag-latency = <2 2 1>;
+		arm,data-latency = <3 2 1>;
+		arm,double-linefill = <1>;
+		arm,double-linefill-incr = <0>;
+		arm,double-linefill-wrap = <1>;
+		arm,prefetch-drop = <1>;
+		arm,prefetch-offset = <7>;
+	};
+
 	clock: clock-controller at 10030000 {
 		compatible = "samsung,exynos4412-clock";
 		reg = <0x10030000 0x20000>;
-- 
1.9.2

[PATCH v8 0/7] Enable L2 cache support on Exynos4210/4x12 SoCs

[Marek Szyprowski]

Hello,

On 2014-11-13 14:18, Marek Szyprowski wrote:
> This is an updated patchset, which intends to add support for L2 cache
> on Exynos4 SoCs on boards running under secure firmware, which requires
> certain initialization steps to be done with help of firmware, as
> selected registers are writable only from secure mode.
>
> First four patches extend existing support for secure write in L2C driver
> to account for design of secure firmware running on Exynos. Namely:
>   1) direct read access to certain registers is needed on Exynos, because
>      secure firmware calls set several registers at once,
>   2) not all boards are running secure firmware, so .write_sec callback
>      needs to be installed in Exynos firmware ops initialization code,
>   3) write access to {DATA,TAG}_LATENCY_CTRL registers fron non-secure world
>      is not allowed and so must use l2c_write_sec as well,
>   4) on certain boards, default value of prefetch register is incorrect
>      and must be overridden at L2C initialization.
> For boards running with firmware that provides access to individual
> L2C registers this series should introduce no functional changes. However
> since the driver is widely used on other platforms I'd like to kindly ask
> any interested people for testing.
>
> Further three patches add implementation of .write_sec and .configure
> callbacks for Exynos secure firmware and necessary DT nodes to enable
> L2 cache.
>
> Changes in this version tested on Exynos4412-based TRATS2 and OdroidU3+
> boards (both with secure firmware). There should be no functional change
> for Exynos boards running without secure firmware. I do not have access
> to affected non-Exynos boards, so I could not test on them.
>
>
> Depends on:
>   - [PATCH v3 0/5] Firmware-assisted suspend/resume of Exynos SoCs
>     (https://lkml.org/lkml/2014/8/26/445)
>     available in samsung/pm2 branch in
>     git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git
>   - L2C patches merged to v3.18-rc3

I assume that after all comments from previous versions, no more changes 
are needed
to this patchset and I would really like to have it queued to v3.19.

Arnd, Olof: could you take this patchset thought arm-soc tree? It already
contains all dependencies.

Kukjin: could you ack this patchset?

> Changelog:
> Changes since v7:
> (https://lkml.org/lkml/2014/10/29/158)
> - rebased onto arm-soc/for-next kernel tree (depends on patches merged to
>    v3.18-rc3 and arm-soc/samsung/pm2 branch)
> - removed 'ARM: l2c: unify L2C-310 OF initialization error messages' patch
>    (no longer needed)
>
> Changes since v6:
> (https://lkml.org/lkml/2014/10/27/233)
> - changed PL310 to L2C-310 prefix in error messages
> - added patch shortening the error message about incorrect associativity
>
> Changes since v5:
> (https://lkml.org/lkml/2014/9/24/364)
> - rebased onto v3.18-rc2
> - added error message about missing properties values
>
> Changes since v4:
> (https://lkml.org/lkml/2014/8/26/461)
>   - rewrote the code accessing l2x0_saved_regs from assembly code
>   - added comment and reworked unconditional call to SMC_CMD_L2X0INVALL
>
>
> Patch summary:
>
> Tomasz Figa (7):
>    ARM: l2c: Refactor the driver to use commit-like interface
>    ARM: l2c: Add interface to ask hypervisor to configure L2C
>    ARM: l2c: Get outer cache .write_sec callback from mach_desc only if
>      not NULL
>    ARM: l2c: Add support for overriding prefetch settings
>    ARM: EXYNOS: Add .write_sec outer cache callback for L2C-310
>    ARM: EXYNOS: Add support for non-secure L2X0 resume
>    ARM: dts: exynos4: Add nodes for L2 cache controller
>
>   Documentation/devicetree/bindings/arm/l2cc.txt |  10 +
>   arch/arm/boot/dts/exynos4210.dtsi              |   9 +
>   arch/arm/boot/dts/exynos4x12.dtsi              |  14 ++
>   arch/arm/include/asm/outercache.h              |   3 +
>   arch/arm/kernel/irq.c                          |   3 +-
>   arch/arm/mach-exynos/firmware.c                |  50 +++++
>   arch/arm/mach-exynos/sleep.S                   |  46 +++++
>   arch/arm/mm/cache-l2x0.c                       | 270 ++++++++++++++++---------
>   8 files changed, 309 insertions(+), 96 deletions(-)
>

Best regards
-- 
Marek Szyprowski, PhD
Samsung R&D Institute Poland

[PATCH v8 0/7] Enable L2 cache support on Exynos4210/4x12 SoCs

[Arnd Bergmann]

On Friday 14 November 2014 15:11:58 Marek Szyprowski wrote:
> 
> I assume that after all comments from previous versions, no more changes 
> are needed
> to this patchset and I would really like to have it queued to v3.19.
> 
> Arnd, Olof: could you take this patchset thought arm-soc tree? It already
> contains all dependencies.
> 
> Kukjin: could you ack this patchset?

I'd rather see this merged through Russell's tree, as most of the patches
are for core code, and only three are for the platform.

For the exynos patches:

Acked-by: Arnd Bergmann <arnd@arndb.de>

	Arnd

[PATCH v8 0/7] Enable L2 cache support on Exynos4210/4x12 SoCs

[Kukjin Kim]

Arnd Bergmann wrote:
> 
> On Friday 14 November 2014 15:11:58 Marek Szyprowski wrote:
> >
> > I assume that after all comments from previous versions, no more changes
> > are needed
> > to this patchset and I would really like to have it queued to v3.19.
> >
> > Arnd, Olof: could you take this patchset thought arm-soc tree? It already
> > contains all dependencies.
> >
> > Kukjin: could you ack this patchset?
> 
> I'd rather see this merged through Russell's tree, as most of the patches
> are for core code, and only three are for the platform.
> 
> For the exynos patches:
> 
> Acked-by: Arnd Bergmann <arnd@arndb.de>
> 
I'm also fine on this series for the exynos stuff:

Acked-by: Kukjin Kim <kgene.kim@samsung.com>

And agree with Arnd's suggestion to handle in rmk tree.
(I think seems this has no dependency with samsung tree)

Thanks,
Kukjin

[PATCH v8 0/7] Enable L2 cache support on Exynos4210/4x12 SoCs

[Marek Szyprowski]

Hello,

On 2014-11-14 15:51, Arnd Bergmann wrote:
> On Friday 14 November 2014 15:11:58 Marek Szyprowski wrote:
>> I assume that after all comments from previous versions, no more changes
>> are needed
>> to this patchset and I would really like to have it queued to v3.19.
>>
>> Arnd, Olof: could you take this patchset thought arm-soc tree? It already
>> contains all dependencies.
>>
>> Kukjin: could you ack this patchset?
> I'd rather see this merged through Russell's tree, as most of the patches
> are for core code, and only three are for the platform.

Ok, I will upload v9 posted yesterday to Russell's patch system when
http://www.arm.linux.org.uk/ gets back to life.

> For the exynos patches:
>
> Acked-by: Arnd Bergmann <arnd@arndb.de>

Best regards
-- 
Marek Szyprowski, PhD
Samsung R&D Institute Poland