[PATCH] regulators: add support max8952 regulator

[kgene.kim@samsung.com (Kukjin Kim)]

Kukjin Kim wrote:
> 
> From: Changhwan Youn <chaos.youn@samsung.com>
> 
> The operation of max8952 is almost similar to max8649 except
> the output voltage range. This patch adds support the max8952
> regulator using current max8649 implementation.
> 
> Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.
> ---
>  drivers/regulator/Kconfig   |    4 ++--
>  drivers/regulator/max8649.c |   43
> ++++++++++++++++++++++++++++++++++++-------
>  2 files changed, 38 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
> index 172951b..fab9a90 100644
> --- a/drivers/regulator/Kconfig
> +++ b/drivers/regulator/Kconfig
> @@ -81,10 +81,10 @@ config REGULATOR_MAX1586
>  	  for PXA27x chips to control VCC_CORE and VCC_USIM voltages.
> 
>  config REGULATOR_MAX8649
> -	tristate "Maxim 8649 voltage regulator"
> +	tristate "Maxim 8649/8952 voltage regulator"
>  	depends on I2C
>  	help
> -	  This driver controls a Maxim 8649 voltage output regulator via
> +	  This driver controls a Maxim 8649/8952 voltage output regulator
via
>  	  I2C bus.
> 
>  config REGULATOR_MAX8660
> diff --git a/drivers/regulator/max8649.c b/drivers/regulator/max8649.c
> index 4520ace..f5d034c 100644
> --- a/drivers/regulator/max8649.c
> +++ b/drivers/regulator/max8649.c
> @@ -22,6 +22,9 @@
>  #define MAX8649_DCDC_STEP	10000		/* uV */
>  #define MAX8649_VOL_MASK	0x3f
> 
> +/* difference between voltages of max8649 and max8952 */
> +#define DIFF_MAX8952_DCDC_VOL	20000		/* uV */
> +
>  /* Registers */
>  #define MAX8649_MODE0		0x00
>  #define MAX8649_MODE1		0x01
> @@ -47,6 +50,11 @@
>  #define MAX8649_RAMP_MASK	(7 << 5)
>  #define MAX8649_RAMP_DOWN	(1 << 1)
> 
> +enum chips {
> +	MAX8649,
> +	MAX8952
> +};
> +
>  struct max8649_regulator_info {
>  	struct regulator_dev	*regulator;
>  	struct i2c_client	*i2c;
> @@ -54,6 +62,7 @@ struct max8649_regulator_info {
>  	struct mutex		io_lock;
> 
>  	int		vol_reg;
> +	int		type;
>  	unsigned	mode:2;	/* bit[1:0] = VID1, VID0 */
>  	unsigned	extclk_freq:2;
>  	unsigned	extclk:1;
> @@ -138,7 +147,12 @@ static inline int check_range(int min_uV, int max_uV)
> 
>  static int max8649_list_voltage(struct regulator_dev *rdev, unsigned
index)
>  {
> -	return (MAX8649_DCDC_VMIN + index * MAX8649_DCDC_STEP);
> +	struct max8649_regulator_info *info = rdev_get_drvdata(rdev);
> +	int ret = MAX8649_DCDC_VMIN + index * MAX8649_DCDC_STEP;
> +
> +	if (info->type == MAX8952)
> +		ret += DIFF_MAX8952_DCDC_VOL;
> +	return ret;
>  }
> 
>  static int max8649_get_voltage(struct regulator_dev *rdev)
> @@ -160,6 +174,11 @@ static int max8649_set_voltage(struct regulator_dev
*rdev,
>  	struct max8649_regulator_info *info = rdev_get_drvdata(rdev);
>  	unsigned char data, mask;
> 
> +	if (info->type == MAX8952) {
> +		min_uV -= DIFF_MAX8952_DCDC_VOL;
> +		max_uV -= DIFF_MAX8952_DCDC_VOL;
> +	}
> +
>  	if (check_range(min_uV, max_uV)) {
>  		dev_err(info->dev, "invalid voltage range (%d, %d) uV\n",
>  			min_uV, max_uV);
> @@ -263,7 +282,6 @@ static struct regulator_ops max8649_dcdc_ops = {
>  	.enable_time	= max8649_enable_time,
>  	.set_mode	= max8649_set_mode,
>  	.get_mode	= max8649_get_mode,
> -
>  };
> 
>  static struct regulator_desc dcdc_desc = {
> @@ -281,6 +299,7 @@ static int __devinit max8649_regulator_probe(struct
> i2c_client *client,
>  	struct max8649_regulator_info *info = NULL;
>  	unsigned char data;
>  	int ret;
> +	int ret2;
> 
>  	info = kzalloc(sizeof(struct max8649_regulator_info), GFP_KERNEL);
>  	if (!info) {
> @@ -313,11 +332,20 @@ static int __devinit max8649_regulator_probe(struct
> i2c_client *client,
> 
>  	ret = max8649_reg_read(info->i2c, MAX8649_CHIP_ID1);
>  	if (ret < 0) {
> -		dev_err(info->dev, "Failed to detect ID of MAX8649:%d\n",
> -			ret);
> +		dev_err(info->dev, "Failed to detect ID of %s:%d\n",
> +			id->name, ret);
> +		goto out;
> +	}
> +
> +	ret2 = max8649_reg_read(info->i2c, MAX8649_CHIP_ID2);
> +	if (ret2 < 0) {
> +		dev_err(info->dev, "Failed to detect ID of %s:%d\n",
> +			id->name, ret2);
>  		goto out;
>  	}
> -	dev_info(info->dev, "Detected MAX8649 (ID:%x)\n", ret);
> +	dev_info(info->dev, "Detected %s (ID:%x %x)\n", id->name, ret,
ret2);
> +
> +	info->type = id->driver_data;
> 
>  	/* enable VID0 & VID1 */
>  	max8649_set_bits(info->i2c, MAX8649_CONTROL, MAX8649_VID_MASK,
> 0);
> @@ -354,7 +382,7 @@ static int __devinit max8649_regulator_probe(struct
> i2c_client *client,
>  		goto out;
>  	}
> 
> -	dev_info(info->dev, "Max8649 regulator device is detected.\n");
> +	dev_info(info->dev, "%s regulator device is detected.\n", id->name);
>  	return 0;
>  out:
>  	kfree(info);
> @@ -375,7 +403,8 @@ static int __devexit max8649_regulator_remove(struct
> i2c_client *client)
>  }
> 
>  static const struct i2c_device_id max8649_id[] = {
> -	{ "max8649", 0 },
> +	{ "max8649", MAX8649 },
> +	{ "max8952", MAX8952 },
>  	{ }
>  };
>  MODULE_DEVICE_TABLE(i2c, max8649_id);
> --
>1.6.2.5