* [PATCH net-next 1/2] net: mdio-mux-mmioreg: Add support for 16bit and 32bit register sizes
2016-11-04 15:51 [PATCH net-next 0/2] ARM64: Add Internal PHY support for Meson GXL Neil Armstrong
@ 2016-11-04 15:51 ` Neil Armstrong
2016-11-04 16:20 ` Florian Fainelli
2016-11-04 15:51 ` [PATCH net-next 2/2] net: phy: Add Meson GXL Internal PHY driver Neil Armstrong
2016-11-09 17:51 ` [PATCH net-next 0/2] ARM64: Add Internal PHY support for Meson GXL David Miller
2 siblings, 1 reply; 7+ messages in thread
From: Neil Armstrong @ 2016-11-04 15:51 UTC (permalink / raw)
To: linux-arm-kernel
In order to support PHY switching on Amlogic GXL SoCs, add support for
16bit and 32bit registers sizes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../devicetree/bindings/net/mdio-mux-mmioreg.txt | 4 +-
drivers/net/phy/mdio-mux-mmioreg.c | 60 +++++++++++++++++-----
2 files changed, 49 insertions(+), 15 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
index 8516929..065e8bd 100644
--- a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
+++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
@@ -3,7 +3,7 @@ Properties for an MDIO bus multiplexer controlled by a memory-mapped device
This is a special case of a MDIO bus multiplexer. A memory-mapped device,
like an FPGA, is used to control which child bus is connected. The mdio-mux
node must be a child of the memory-mapped device. The driver currently only
-supports devices with eight-bit registers.
+supports devices with 8, 16 or 32-bit registers.
Required properties in addition to the generic multiplexer properties:
@@ -11,7 +11,7 @@ Required properties in addition to the generic multiplexer properties:
- reg : integer, contains the offset of the register that controls the bus
multiplexer. The size field in the 'reg' property is the size of
- register, and must therefore be 1.
+ register, and must therefore be 1, 2, or 4.
- mux-mask : integer, contains an eight-bit mask that specifies which
bits in the register control the actual bus multiplexer. The
diff --git a/drivers/net/phy/mdio-mux-mmioreg.c b/drivers/net/phy/mdio-mux-mmioreg.c
index d0bed52..6a33646 100644
--- a/drivers/net/phy/mdio-mux-mmioreg.c
+++ b/drivers/net/phy/mdio-mux-mmioreg.c
@@ -21,7 +21,8 @@
struct mdio_mux_mmioreg_state {
void *mux_handle;
phys_addr_t phys;
- uint8_t mask;
+ unsigned int iosize;
+ unsigned int mask;
};
/*
@@ -47,17 +48,47 @@ static int mdio_mux_mmioreg_switch_fn(int current_child, int desired_child,
struct mdio_mux_mmioreg_state *s = data;
if (current_child ^ desired_child) {
- void __iomem *p = ioremap(s->phys, 1);
- uint8_t x, y;
-
+ void __iomem *p = ioremap(s->phys, s->iosize);
if (!p)
return -ENOMEM;
- x = ioread8(p);
- y = (x & ~s->mask) | desired_child;
- if (x != y) {
- iowrite8((x & ~s->mask) | desired_child, p);
- pr_debug("%s: %02x -> %02x\n", __func__, x, y);
+ switch (s->iosize) {
+ case sizeof(uint8_t): {
+ uint8_t x, y;
+
+ x = ioread8(p);
+ y = (x & ~s->mask) | desired_child;
+ if (x != y) {
+ iowrite8((x & ~s->mask) | desired_child, p);
+ pr_debug("%s: %02x -> %02x\n", __func__, x, y);
+ }
+
+ break;
+ }
+ case sizeof(uint16_t): {
+ uint16_t x, y;
+
+ x = ioread16(p);
+ y = (x & ~s->mask) | desired_child;
+ if (x != y) {
+ iowrite16((x & ~s->mask) | desired_child, p);
+ pr_debug("%s: %04x -> %04x\n", __func__, x, y);
+ }
+
+ break;
+ }
+ case sizeof(uint32_t): {
+ uint32_t x, y;
+
+ x = ioread32(p);
+ y = (x & ~s->mask) | desired_child;
+ if (x != y) {
+ iowrite32((x & ~s->mask) | desired_child, p);
+ pr_debug("%s: %08x -> %08x\n", __func__, x, y);
+ }
+
+ break;
+ }
}
iounmap(p);
@@ -88,8 +119,11 @@ static int mdio_mux_mmioreg_probe(struct platform_device *pdev)
}
s->phys = res.start;
- if (resource_size(&res) != sizeof(uint8_t)) {
- dev_err(&pdev->dev, "only 8-bit registers are supported\n");
+ s->iosize = resource_size(&res);
+ if (s->iosize != sizeof(uint8_t) &&
+ s->iosize != sizeof(uint16_t) &&
+ s->iosize != sizeof(uint32_t)) {
+ dev_err(&pdev->dev, "only 8/16/32-bit registers are supported\n");
return -EINVAL;
}
@@ -98,8 +132,8 @@ static int mdio_mux_mmioreg_probe(struct platform_device *pdev)
dev_err(&pdev->dev, "missing or invalid mux-mask property\n");
return -ENODEV;
}
- if (be32_to_cpup(iprop) > 255) {
- dev_err(&pdev->dev, "only 8-bit registers are supported\n");
+ if (be32_to_cpup(iprop) >= BIT(s->iosize * 8)) {
+ dev_err(&pdev->dev, "only 8/16/32-bit registers are supported\n");
return -EINVAL;
}
s->mask = be32_to_cpup(iprop);
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH net-next 2/2] net: phy: Add Meson GXL Internal PHY driver
2016-11-04 15:51 [PATCH net-next 0/2] ARM64: Add Internal PHY support for Meson GXL Neil Armstrong
2016-11-04 15:51 ` [PATCH net-next 1/2] net: mdio-mux-mmioreg: Add support for 16bit and 32bit register sizes Neil Armstrong
@ 2016-11-04 15:51 ` Neil Armstrong
2016-11-04 16:19 ` Florian Fainelli
2016-11-05 10:39 ` Andrew Lunn
2016-11-09 17:51 ` [PATCH net-next 0/2] ARM64: Add Internal PHY support for Meson GXL David Miller
2 siblings, 2 replies; 7+ messages in thread
From: Neil Armstrong @ 2016-11-04 15:51 UTC (permalink / raw)
To: linux-arm-kernel
Add driver for the Internal RMII PHY found in the Amlogic Meson GXL SoCs.
This PHY seems to only implement some standard registers and need some
workarounds to provide autoneg values from vendor registers.
Some magic values are currently used to configure the PHY, and this a
temporary setup until clarification about these registers names and
registers fields are provided by Amlogic.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/net/phy/Kconfig | 5 +++
drivers/net/phy/Makefile | 1 +
drivers/net/phy/meson-gxl.c | 81 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 87 insertions(+)
create mode 100644 drivers/net/phy/meson-gxl.c
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 2651c8d..b48943a 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -264,6 +264,11 @@ config MARVELL_PHY
---help---
Currently has a driver for the 88E1011S
+config MESON_GXL_PHY
+ tristate "Amlogic Meson GXL Internal PHY"
+ ---help---
+ Currently has a driver for the Amlogic Meson GXL Internal PHY
+
config MICREL_PHY
tristate "Micrel PHYs"
---help---
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index e58667d..3cd5af7 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_INTEL_XWAY_PHY) += intel-xway.o
obj-$(CONFIG_LSI_ET1011C_PHY) += et1011c.o
obj-$(CONFIG_LXT_PHY) += lxt.o
obj-$(CONFIG_MARVELL_PHY) += marvell.o
+obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o
obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o
obj-$(CONFIG_MICREL_PHY) += micrel.o
obj-$(CONFIG_MICROCHIP_PHY) += microchip.o
diff --git a/drivers/net/phy/meson-gxl.c b/drivers/net/phy/meson-gxl.c
new file mode 100644
index 0000000..1ea69b7
--- /dev/null
+++ b/drivers/net/phy/meson-gxl.c
@@ -0,0 +1,81 @@
+/*
+ * Amlogic Meson GXL Internal PHY Driver
+ *
+ * Copyright (C) 2015 Amlogic, Inc. All rights reserved.
+ * Copyright (C) 2016 BayLibre, SAS. All rights reserved.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+#include <linux/netdevice.h>
+
+static int meson_gxl_config_init(struct phy_device *phydev)
+{
+ /* Enable Analog and DSP register Bank access by */
+ phy_write(phydev, 0x14, 0x0000);
+ phy_write(phydev, 0x14, 0x0400);
+ phy_write(phydev, 0x14, 0x0000);
+ phy_write(phydev, 0x14, 0x0400);
+
+ /* Write Analog register 23 */
+ phy_write(phydev, 0x17, 0x8E0D);
+ phy_write(phydev, 0x14, 0x4417);
+
+ /* Enable fractional PLL */
+ phy_write(phydev, 0x17, 0x0005);
+ phy_write(phydev, 0x14, 0x5C1B);
+
+ /* Program fraction FR_PLL_DIV1 */
+ phy_write(phydev, 0x17, 0x029A);
+ phy_write(phydev, 0x14, 0x5C1D);
+
+ /* Program fraction FR_PLL_DIV1 */
+ phy_write(phydev, 0x17, 0xAAAA);
+ phy_write(phydev, 0x14, 0x5C1C);
+
+ return 0;
+}
+
+static struct phy_driver meson_gxl_phy[] = {
+ {
+ .phy_id = 0x01814400,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Meson GXL Internal PHY",
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_IS_INTERNAL,
+ .config_init = meson_gxl_config_init,
+ .config_aneg = genphy_config_aneg,
+ .aneg_done = genphy_aneg_done,
+ .read_status = genphy_read_status,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ },
+};
+
+static struct mdio_device_id __maybe_unused meson_gxl_tbl[] = {
+ { 0x01814400, 0xfffffff0 },
+ { }
+};
+
+module_phy_driver(meson_gxl_phy);
+
+MODULE_DEVICE_TABLE(mdio, meson_gxl_tbl);
+
+MODULE_DESCRIPTION("Amlogic Meson GXL Internal PHY driver");
+MODULE_AUTHOR("Baoqi wang");
+MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");
+MODULE_LICENSE("GPL");
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread