From: Roger Quadros <rogerq@ti.com>
To: Nitin Yadav <n-yadav@ti.com>, <nm@ti.com>, <vigneshr@ti.com>
Cc: <kristo@kernel.org>, <robh+dt@kernel.org>,
<krzysztof.kozlowski+dt@linaro.org>, <conor+dt@kernel.org>,
<catalin.marinas@arm.com>, <will@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 1/3] arm64: dts: ti: Add GPMC NAND support
Date: Fri, 15 Sep 2023 14:16:06 +0300 [thread overview]
Message-ID: <0994c10b-8805-7ce3-dc1b-13410b3a959c@ti.com> (raw)
In-Reply-To: <20230913114711.2937844-2-n-yadav@ti.com>
Hi Nitin,
On 13.9.2023 14.47, Nitin Yadav wrote:
> Add support for AM62Q NAND card: X8 NAND EXPANSION
> BOARD card (PROC143E1) for AM62x LP SK board.
This patch is not adding NAND support but GPMC and ELM nodes.
>
> Signed-off-by: Nitin Yadav <n-yadav@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 29 ++++++++++++++++++++++++
> arch/arm64/boot/dts/ti/k3-am62.dtsi | 2 ++
> 2 files changed, 31 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
> index 284b90c94da8..e93e79d8083f 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
> @@ -955,4 +955,33 @@ mcasp2: audio-controller@2b20000 {
> power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
> status = "disabled";
> };
> + gpmc0: memory-controller@3b000000 {
> + status = "disabled";
> + compatible = "ti,am64-gpmc";
> + power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 80 0>;
> + clock-names = "fck";
> + reg = <0x00 0x03b000000 0x00 0x400>,
> + <0x00 0x050000000 0x00 0x8000000>;
> + reg-names = "cfg", "data";
> + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
> + gpmc,num-cs = <3>;
> + gpmc,num-waitpins = <2>;
> + #address-cells = <2>;
> + #size-cells = <1>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + elm0: ecc@25010000 {
> + status = "disabled";
> + compatible = "ti,am3352-elm";
> + reg = <0x00 0x25010000 0x00 0x2000>;
> + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 54 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 54 0>;
> + clock-names = "fck";
> + };
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-am62.dtsi b/arch/arm64/boot/dts/ti/k3-am62.dtsi
> index 11f14eef2d44..f7d8aad0a016 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62.dtsi
> @@ -76,6 +76,8 @@ cbass_main: bus@f0000 {
> <0x00 0x70000000 0x00 0x70000000 0x00 0x00010000>, /* OCSRAM */
> <0x01 0x00000000 0x01 0x00000000 0x00 0x00310000>, /* A53 PERIPHBASE */
> <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS0 DAT3 */
> + <0x00 0x3b000000 0x00 0x3b000000 0x00 0x00000400>, /* GPMC0_CFG */
> + <0x00 0x50000000 0x00 0x50000000 0x00 0x08000000>, /* GPMC0 DATA */
>
> /* MCU Domain Range */
> <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>,
--
cheers,
-roger
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2023-09-15 11:17 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-09-13 11:47 [PATCH 0/3] Add support for GPMC NAND Nitin Yadav
2023-09-13 11:47 ` [PATCH 1/3] arm64: dts: ti: Add GPMC NAND support Nitin Yadav
2023-09-14 6:27 ` Krzysztof Kozlowski
2023-09-14 9:26 ` Nitin Yadav
2023-09-14 16:04 ` Nishanth Menon
2023-09-15 9:23 ` Nitin Yadav
2023-09-15 12:22 ` Nishanth Menon
2023-09-15 11:16 ` Roger Quadros [this message]
2023-09-13 11:47 ` [PATCH 2/3] arm64: dts: ti: Add GPMC NAND overlay Nitin Yadav
2023-09-13 11:47 ` [PATCH 3/3] arm64: defconfig: Enable GPMC NAND support Nitin Yadav
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0994c10b-8805-7ce3-dc1b-13410b3a959c@ti.com \
--to=rogerq@ti.com \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=n-yadav@ti.com \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox