From: b.zolnierkie@samsung.com (Bartlomiej Zolnierkiewicz)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2] ARM: dts: Add missing CPU frequencies for Exynos5422/5800
Date: Thu, 15 Dec 2016 12:55:59 +0100 [thread overview]
Message-ID: <10512254.nyUcL0zgTP@amdc3058> (raw)
Add missing 2000MHz & 1900MHz OPPs (for A15 cores) and 1400MHz OPP
(for A7 cores). Also update common Odroid-XU3 Lite/XU3/XU4 thermal
cooling maps to account for new OPPs.
Since new OPPs are not available on all Exynos5422/5800 boards modify
dts files for Odroid-XU3 Lite (limited to 1.8 GHz / 1.3 GHz) & Peach
Pi (limited to 2.0 GHz / 1.3 GHz) accordingly.
Tested on Odroid-XU3 and XU3 Lite.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Ben Gamari <ben@smart-cactus.org>
Cc: Arjun K V <arjun.kv@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v2:
- added comments about limitations of SoC revisions used by Odroid-XU3 Lite and
Peach Pi boards (suggested by Javier)
- removed redundant opp_a7_14 label
- added Arjun to Cc:
Javier, could you test it on Peach Pi board?
arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 14 ++++++-------
arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts | 22 +++++++++++++++++++++
arch/arm/boot/dts/exynos5800-peach-pi.dts | 9 ++++++++
arch/arm/boot/dts/exynos5800.dtsi | 15 ++++++++++++++
4 files changed, 53 insertions(+), 7 deletions(-)
Index: b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
===================================================================
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi 2016-12-15 12:43:54.365955950 +0100
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi 2016-12-15 12:43:54.361955949 +0100
@@ -118,7 +118,7 @@
/*
* When reaching cpu_alert3, reduce CPU
* by 2 steps. On Exynos5422/5800 that would
- * be: 1600 MHz and 1100 MHz.
+ * (usually) be: 1800 MHz and 1200 MHz.
*/
map3 {
trip = <&cpu_alert3>;
@@ -131,16 +131,16 @@
/*
* When reaching cpu_alert4, reduce CPU
- * further, down to 600 MHz (11 steps for big,
- * 7 steps for LITTLE).
+ * further, down to 600 MHz (13 steps for big,
+ * 8 steps for LITTLE).
*/
- map5 {
+ cooling_map5: map5 {
trip = <&cpu_alert4>;
- cooling-device = <&cpu0 3 7>;
+ cooling-device = <&cpu0 3 8>;
};
- map6 {
+ cooling_map6: map6 {
trip = <&cpu_alert4>;
- cooling-device = <&cpu4 3 11>;
+ cooling-device = <&cpu4 3 13>;
};
};
};
Index: b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts
===================================================================
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts 2016-12-15 12:43:54.365955950 +0100
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts 2016-12-15 12:43:54.361955949 +0100
@@ -21,6 +21,28 @@
compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5";
};
+/*
+ * Odroid XU3-Lite board uses SoC revision with lower maximum frequencies
+ * than Odroid XU3/XU4 boards: 1.8 GHz for A15 cores & 1.3 GHz for A7 cores.
+ * Therefore we need to update OPPs tables and thermal maps accordingly.
+ */
+&cluster_a15_opp_table {
+ /delete-node/opp at 2000000000;
+ /delete-node/opp at 1900000000;
+};
+
+&cluster_a7_opp_table {
+ /delete-node/opp at 1400000000;
+};
+
+&cooling_map5 {
+ cooling-device = <&cpu0 3 7>;
+};
+
+&cooling_map6 {
+ cooling-device = <&cpu4 3 11>;
+};
+
&pwm {
/*
* PWM 0 -- fan
Index: b/arch/arm/boot/dts/exynos5800-peach-pi.dts
===================================================================
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts 2016-12-15 12:43:54.365955950 +0100
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts 2016-12-15 12:43:54.361955949 +0100
@@ -146,6 +146,15 @@
vdd-supply = <&ldo9_reg>;
};
+/*
+ * Peach Pi board uses SoC revision with lower maximum frequency for A7 cores
+ * (1.3 GHz instead of 1.4 GHz) than Odroid XU3/XU4 boards. Thus we need to
+ * update A7 OPPs table accordingly.
+ */
+&cluster_a7_opp_table {
+ /delete-property/opp at 1400000000;
+};
+
&cpu0 {
cpu-supply = <&buck2_reg>;
};
Index: b/arch/arm/boot/dts/exynos5800.dtsi
===================================================================
--- a/arch/arm/boot/dts/exynos5800.dtsi 2016-12-15 12:43:54.365955950 +0100
+++ b/arch/arm/boot/dts/exynos5800.dtsi 2016-12-15 12:43:54.361955949 +0100
@@ -24,6 +24,16 @@
};
&cluster_a15_opp_table {
+ opp at 2000000000 {
+ opp-hz = /bits/ 64 <2000000000>;
+ opp-microvolt = <1250000>;
+ clock-latency-ns = <140000>;
+ };
+ opp at 1900000000 {
+ opp-hz = /bits/ 64 <1900000000>;
+ opp-microvolt = <1250000>;
+ clock-latency-ns = <140000>;
+ };
opp at 1700000000 {
opp-microvolt = <1250000>;
};
@@ -85,6 +95,11 @@
};
&cluster_a7_opp_table {
+ opp at 1400000000 {
+ opp-hz = /bits/ 64 <1400000000>;
+ opp-microvolt = <1250000>;
+ clock-latency-ns = <140000>;
+ };
opp at 1300000000 {
opp-microvolt = <1250000>;
};
next reply other threads:[~2016-12-15 11:55 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-15 11:55 Bartlomiej Zolnierkiewicz [this message]
2016-12-15 13:55 ` [PATCH v2] ARM: dts: Add missing CPU frequencies for Exynos5422/5800 Markus Reichl
2016-12-16 0:54 ` Doug Anderson
2016-12-29 14:17 ` Krzysztof Kozlowski
2017-01-04 21:05 ` Doug Anderson
2017-01-04 23:57 ` Javier Martinez Canillas
2017-01-05 19:40 ` Krzysztof Kozlowski
2016-12-16 19:18 ` Javier Martinez Canillas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=10512254.nyUcL0zgTP@amdc3058 \
--to=b.zolnierkie@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox