* spitz battery driver
@ 2009-11-09 13:58 Pavel Machek
2009-11-10 3:48 ` Eric Miao
0 siblings, 1 reply; 5+ messages in thread
From: Pavel Machek @ 2009-11-09 13:58 UTC (permalink / raw)
To: linux-arm-kernel
Hi!
This introduces battery driver for spitz. For now it is
monitoring&debug-only.
Signed-off-by: Pavel Machek <pavel@ucw.cz> (but not meant for merge)
--- ./drivers/power.ofic/Makefile 2009-10-06 13:51:29.000000000 +0200
+++ ./drivers/power/Makefile 2009-10-11 16:12:09.000000000 +0200
@@ -24,6 +24,7 @@
obj-$(CONFIG_BATTERY_PMU) += pmu_battery.o
obj-$(CONFIG_BATTERY_OLPC) += olpc_battery.o
obj-$(CONFIG_BATTERY_TOSA) += tosa_battery.o
+obj-m += spitz_battery.o
obj-$(CONFIG_BATTERY_WM97XX) += wm97xx_battery.o
obj-$(CONFIG_BATTERY_BQ27x00) += bq27x00_battery.o
obj-$(CONFIG_BATTERY_DA9030) += da9030_battery.o
diff -ur ./drivers/power.ofic/power_supply_sysfs.c ./drivers/power/power_supply_sysfs.c
--- ./drivers/power.ofic/power_supply_sysfs.c 2009-10-06 13:51:29.000000000 +0200
+++ ./drivers/power/power_supply_sysfs.c 2009-10-15 05:45:46.000000000 +0200
@@ -39,7 +39,8 @@
static ssize_t power_supply_show_property(struct device *dev,
struct device_attribute *attr,
- char *buf) {
+ char *buf)
+{
static char *status_text[] = {
"Unknown", "Charging", "Discharging", "Not charging", "Full"
};
@@ -135,7 +136,8 @@
static ssize_t power_supply_show_static_attrs(struct device *dev,
struct device_attribute *attr,
- char *buf) {
+ char *buf)
+{
static char *type_text[] = { "Battery", "UPS", "Mains", "USB" };
struct power_supply *psy = dev_get_drvdata(dev);
diff -ur ./drivers/power.ofic/spitz_battery.c ./drivers/power/spitz_battery.c
--- ./drivers/power.ofic/spitz_battery.c 2009-10-11 16:14:11.000000000 +0200
+++ ./drivers/power/spitz_battery.c 2009-10-22 07:27:52.000000000 +0200
@@ -0,0 +1,430 @@
+/*
+ * Battery and Power Management code for the Sharp SL-3000c
+ *
+ * Copyright (c) 2009 Pavel Machek <pavel@ucw.cz>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Li-ion batteries are angry beasts, and they like to explode.
+ * If angry lithium comes your way, the hw was misdesigned.
+ *
+ */
+#include <linux/platform_device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/power_supply.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+#include <mach/spitz.h>
+#include <mach/sharpsl.h>
+#include <mach/sharpsl_pm.h>
+
+#include "../../arch/arm/mach-pxa/sharpsl.h"
+
+extern struct sharpsl_pm_status sharpsl_pm;
+
+
+struct spitz_bat {
+ struct power_supply psy;
+
+ bool (*is_present)(struct spitz_bat *bat);
+};
+
+static struct spitz_bat spitz_bat_main, spitz_ac;
+
+extern int sharpsl_pm_pxa_read_max1111(int channel);
+
+int basic_current = 125; /* miliAmp */
+int battery_resistance = 422; /* miliOhm */
+
+/* 422 seems to be suitable for very old, 1Ah battery.
+ 2Ah battery probably has better resistance */
+
+/* Unfortunately, resistance depends on state of charge, current
+ * direction and temperature.
+ *
+ * Ouch, and dependency is actually _not_ too simple. It is lowest
+ * at 3.55V, very slowly rises at 4V (approximately linear dependency),
+ * and quickly rises towards 3.2V (in something exponential-looking).
+ *
+ * It is about same at 25Celsius and 40Celsius, and about 2.5x the value
+ * on 0Celsius, rising _very_ sharply.
+ *
+ * Li-ion should only be charged between 0 and 45 Celsius, and discharged
+ * between -20 and 60 celsius.
+ */
+
+extern int backlight_current;
+
+int battery_current(void)
+{
+ int intensity = sharpsl_pm.machinfo->backlight_get_status ? sharpsl_pm.machinfo->backlight_get_status() : 0;
+
+ return basic_current + backlight_current;
+}
+
+int liion_internal_voltage(int voltage, int current_ma)
+{
+ return voltage + (battery_resistance * current_ma / 1000);
+}
+
+int liion_expected_voltage(int internal_voltage, int current_ma)
+{
+ return internal_voltage - (battery_resistance * current_ma / 1000);
+}
+
+/* returns mV */
+int liion_voltage(void)
+{
+ /* Thanks to Stanislav B. ADC has 3.3V as reference,
+ is connected to battery over 47kOhm,
+ and to ground over 100kOhm. */
+ return (sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_VOLT) * 147 * 33)/256;
+}
+
+/* See for example http://www.kokam.com/english/biz/rc.html for
+ * voltage/capacity characteristic. I assume it is going to be
+ * reasonably similar to li-ion used in collie.
+ *
+ */
+
+/*
+ { 420, 100 },
+ { 417, 95 }, means it will report 100% between 418 and 420
+ */
+
+struct battery_thresh battery_levels[] = {
+ { 3980, 100 },
+ { 3900, 95 },
+ { 3860, 90 },
+ { 3800, 85 },
+ { 3760, 80 },
+ { 3720, 74 },
+ { 3680, 69 },
+ { 3620, 65 },
+ { 3570, 59 },
+ { 3560, 55 },
+ { 3550, 48 },
+ { 3530, 45 },
+ { 3510, 39 },
+ { 3490, 33 },
+ { 3470, 29 },
+ { 3450, 23 },
+ { 3410, 16 },
+ { 0, 0 },
+};
+
+int get_percentage(void)
+{
+ int i = ARRAY_SIZE(battery_levels);
+ struct battery_thresh *thresh;
+ int voltage = liion_internal_voltage(liion_voltage(), battery_current());
+
+ thresh = battery_levels;
+
+ while (i > 0 && (voltage > thresh[i].voltage))
+ i--;
+
+ return thresh[i].percentage;
+}
+
+static int spitz_bat_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ int ret = 0;
+ struct spitz_bat *bat = container_of(psy, struct spitz_bat, psy);
+
+ val->intval = 0;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_HEALTH:
+ /* POWER_SUPPLY_HEALTH_OVERHEAT , POWER_SUPPLY_HEALTH_COLD,
+ POWER_SUPPLY_HEALTH_OVERVOLTAGE, POWER_SUPPLY_HEALTH_UNSPEC_FAILURE, POWER_SUPPLY_HEALTH_GOOD
+ */
+ return 0;
+ case POWER_SUPPLY_PROP_CHARGE_TYPE:
+ val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
+ if (gpio_get_value(SPITZ_GPIO_CHRG_ON) == 0) {
+ if (gpio_get_value(SPITZ_GPIO_JK_B) == 1)
+ val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
+ else
+ val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
+ }
+ return 0;
+ case POWER_SUPPLY_PROP_STATUS:
+ {
+ int status = 0;
+
+ if (gpio_get_value(SPITZ_GPIO_CHRG_ON) == 0)
+ printk("Chrg bit on. ");
+ if (gpio_get_value(SPITZ_GPIO_JK_B) == 0)
+ printk("Slow charge bit on. ");
+
+ val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
+
+ if (!sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN))
+ val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+ else {
+ if (gpio_get_value(SPITZ_GPIO_CHRG_ON) == 0)
+ val->intval = POWER_SUPPLY_STATUS_CHARGING;
+ if (sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_CHRGFULL))
+ val->intval = POWER_SUPPLY_STATUS_FULL;
+ }
+
+ printk("ACIN: %d ", sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN));
+ printk("Chrgfull: %d ", sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_CHRGFULL));
+ printk("Fatal: %d ", sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_FATAL));
+ printk("ACIN_volt: %d\n", sharpsl_pm.machinfo->read_devdata(SHARPSL_ACIN_VOLT));
+
+ return 0;
+ }
+ case POWER_SUPPLY_PROP_TECHNOLOGY:
+ val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
+ return 0;
+ case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+ val->intval = liion_voltage()*1000;
+ return 0;
+ case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
+ val->intval = 4200000;
+ return 0;
+ case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+ val->intval = 3400000;
+ return 0;
+ case POWER_SUPPLY_PROP_TEMP:
+ mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
+ sharpsl_pm.machinfo->measure_temp(1);
+ mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
+ val->intval = sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_TEMP);
+ sharpsl_pm.machinfo->measure_temp(0);
+ /* 121: battery finished charging in 22C room */
+ /* 141: outside at 6C */
+ return 0;
+ case POWER_SUPPLY_PROP_MODEL_NAME:
+ val->strval = "spitz-battery";
+ return 0;
+ case POWER_SUPPLY_PROP_PRESENT:
+ val->intval = 1;
+ return 0;
+ /* add these */
+ case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
+ val->intval = 2000000;
+ return 0;
+ case POWER_SUPPLY_PROP_CAPACITY:
+ val->intval = get_percentage();
+ return 0;
+ case POWER_SUPPLY_PROP_VOLTAGE_AVG:
+ val->intval = liion_internal_voltage(liion_voltage(), battery_current())*1000;
+ return 0;
+ case POWER_SUPPLY_PROP_CURRENT_NOW:
+ val->intval = battery_current() * 1000;
+ return 0;
+ default:
+ return -EINVAL;
+ }
+ return -EINVAL;
+}
+
+static int spitz_ac_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ int ret = 0;
+ struct spitz_bat *bat = container_of(psy, struct spitz_bat, psy);
+
+ val->intval = 0;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_STATUS:
+ val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
+ return 0;
+ case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+ /* Thanks to Stanislav B. ADC has 3.3V as reference,
+ is connected to acin over 2kOhm,
+ and to ground over 1kOhm. */
+ val->intval = (sharpsl_pm.machinfo->read_devdata(SHARPSL_ACIN_VOLT) * 3000 * 3300)/256;
+ return 0;
+ case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
+ val->intval = 5250000;
+ return 0;
+ case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+ val->intval = 4750000;
+ return 0;
+ case POWER_SUPPLY_PROP_MODEL_NAME:
+ val->strval = "spitz-power-supply";
+ return 0;
+ case POWER_SUPPLY_PROP_PRESENT:
+ val->intval = sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN);
+ return 0;
+ default:
+ return -EINVAL;
+ }
+ return -EINVAL;
+}
+
+static void spitz_bat_external_power_changed(struct power_supply *psy)
+{
+}
+
+
+static enum power_supply_property spitz_bat_main_props[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_TECHNOLOGY,
+ POWER_SUPPLY_PROP_VOLTAGE_NOW,
+ POWER_SUPPLY_PROP_VOLTAGE_AVG,
+ POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
+ POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
+ POWER_SUPPLY_PROP_TEMP,
+ POWER_SUPPLY_PROP_PRESENT,
+ POWER_SUPPLY_PROP_CHARGE_TYPE,
+ POWER_SUPPLY_PROP_HEALTH,
+ POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+ POWER_SUPPLY_PROP_CURRENT_NOW,
+ POWER_SUPPLY_PROP_CAPACITY,
+};
+
+static struct spitz_bat spitz_bat_main = {
+ .psy = {
+ .name = "main-battery",
+ .type = POWER_SUPPLY_TYPE_BATTERY,
+ .properties = spitz_bat_main_props,
+ .num_properties = ARRAY_SIZE(spitz_bat_main_props),
+ .get_property = spitz_bat_get_property,
+ .external_power_changed = spitz_bat_external_power_changed,
+ .use_for_apm = 1,
+ },
+};
+
+static enum power_supply_property spitz_ac_props[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_VOLTAGE_NOW,
+ POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
+ POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
+ POWER_SUPPLY_PROP_PRESENT,
+};
+
+static struct spitz_bat spitz_ac = {
+ .psy = {
+ .name = "ac",
+ .type = POWER_SUPPLY_TYPE_MAINS,
+ .properties = spitz_ac_props,
+ .num_properties = ARRAY_SIZE(spitz_ac_props),
+ .get_property = spitz_ac_get_property,
+ },
+};
+
+#ifdef CONFIG_PM
+static int spitz_bat_suspend(struct platform_device *dev, pm_message_t state)
+{
+ return 0;
+}
+
+static int spitz_bat_resume(struct platform_device *dev)
+{
+ return 0;
+}
+#else
+#define spitz_bat_suspend NULL
+#define spitz_bat_resume NULL
+#endif
+
+
+static ssize_t spitz_bat_limit_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ sprintf(buf, "Hello :-)");
+ return 9;
+}
+
+static ssize_t spitz_bat_limit_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ if (!strncmp(buf, "fastcharge", 10)) {
+ gpio_set_value(SPITZ_GPIO_JK_B, 1);
+ gpio_set_value(SPITZ_GPIO_CHRG_ON, 0);
+ return 10;
+ }
+ if (!strncmp(buf, "slowcharge", 10)) {
+ gpio_set_value(SPITZ_GPIO_JK_B, 0);
+ gpio_set_value(SPITZ_GPIO_CHRG_ON, 0);
+ return 10;
+ }
+ if (!strncmp(buf, "nonecharge", 10)) {
+ gpio_set_value(SPITZ_GPIO_JK_B, 0);
+ gpio_set_value(SPITZ_GPIO_CHRG_ON, 1);
+ return 10;
+ }
+ return -EINVAL;
+}
+
+
+static DEVICE_ATTR(limit, S_IRUGO | S_IWUSR, spitz_bat_limit_show, spitz_bat_limit_store);
+#if 0
+static struct device_attribute dev_attr_limit = {
+ .attr = { .name = "limit", .mode = 0644 },
+ .show = spitz_bat_limit_show,
+ .store = spitz_bat_limit_store,
+};
+#endif
+
+static int __devinit spitz_bat_probe(struct platform_device *dev)
+{
+ int ret;
+ int i;
+
+ if (!machine_is_spitz())
+ return -ENODEV;
+
+ printk("spitz_bat_probe: register\n");
+ power_supply_register(&dev->dev, &spitz_bat_main.psy);
+ power_supply_register(&dev->dev, &spitz_ac.psy);
+ device_create_file(&dev->dev, &dev_attr_limit);
+
+ return 0;
+}
+
+static int __devexit spitz_bat_remove(struct platform_device *dev)
+{
+ int i;
+
+ device_remove_file(&dev->dev, &dev_attr_limit);
+ power_supply_unregister(&spitz_bat_main.psy);
+ power_supply_unregister(&spitz_ac.psy);
+ return 0;
+}
+
+
+static struct platform_driver spitz_bat_driver = {
+ .driver.name = "spitz-battery",
+ .driver.owner = THIS_MODULE,
+ .probe = spitz_bat_probe,
+ .remove = __devexit_p(spitz_bat_remove),
+ .suspend = spitz_bat_suspend,
+ .resume = spitz_bat_resume,
+};
+
+static int __init spitz_bat_init(void)
+{
+ return platform_driver_register(&spitz_bat_driver);
+}
+
+static void __exit spitz_bat_exit(void)
+{
+ platform_driver_unregister(&spitz_bat_driver);
+}
+
+module_init(spitz_bat_init);
+module_exit(spitz_bat_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Pavel Machek");
+MODULE_DESCRIPTION("Spitz battery driver");
+MODULE_ALIAS("platform:spitz-battery");
diff -ur ./drivers/video/backlight.ofic/corgi_lcd.c ./drivers/video/backlight/corgi_lcd.c
--- ./drivers/video/backlight.ofic/corgi_lcd.c 2009-10-18 18:11:36.000000000 +0200
+++ ./drivers/video/backlight/corgi_lcd.c 2009-10-18 18:37:09.000000000 +0200
@@ -388,17 +388,33 @@
.set_mode = corgi_lcd_set_mode,
};
-static int corgi_bl_get_intensity(struct backlight_device *bd)
+int corgi_bl_get_intensity(struct backlight_device *bd)
{
struct corgi_lcd *lcd = dev_get_drvdata(&bd->dev);
return lcd->intensity;
}
+EXPORT_SYMBOL(corgi_bl_get_intensity);
+
+int backlight_current;
+EXPORT_SYMBOL(backlight_current);
static int corgi_bl_set_intensity(struct corgi_lcd *lcd, int intensity)
{
int cont;
+ backlight_current = 0;
+ if (intensity > 0)
+ backlight_current = 55;
+ if (intensity > 10)
+ backlight_current = 115;
+ if (intensity > 20)
+ backlight_current = 140;
+ if (intensity > 30)
+ backlight_current = 180;
+ if (intensity > 45)
+ backlight_current = 245;
+
if (intensity > 0x10)
intensity += 0x10;
@@ -433,8 +449,9 @@
if (corgibl_flags & CORGIBL_SUSPENDED)
intensity = 0;
- if (corgibl_flags & CORGIBL_BATTLOW)
- intensity &= lcd->limit_mask;
+
+ if ((corgibl_flags & CORGIBL_BATTLOW) && intensity > lcd->limit_mask)
+ intensity = lcd->limit_mask;
return corgi_bl_set_intensity(lcd, intensity);
}
diff -ur ./arch/arm.ofic/mach-pxa/corgi_pm.c ./arch/arm/mach-pxa/corgi_pm.c
--- ./arch/arm.ofic/mach-pxa/corgi_pm.c 2009-09-10 00:13:59.000000000 +0200
+++ ./arch/arm/mach-pxa/corgi_pm.c 2009-10-22 19:19:02.000000000 +0200
@@ -35,6 +35,92 @@
#define SHARPSL_FATAL_ACIN_VOLT 182 /* 3.45V */
#define SHARPSL_FATAL_NOACIN_VOLT 170 /* 3.40V */
+static const struct battery_thresh corgi_battery_levels_acin[] = {
+ { 213, 100},
+ { 212, 98},
+ { 211, 95},
+ { 210, 93},
+ { 209, 90},
+ { 208, 88},
+ { 207, 85},
+ { 206, 83},
+ { 205, 80},
+ { 204, 78},
+ { 203, 75},
+ { 202, 73},
+ { 201, 70},
+ { 200, 68},
+ { 199, 65},
+ { 198, 63},
+ { 197, 60},
+ { 196, 58},
+ { 195, 55},
+ { 194, 53},
+ { 193, 50},
+ { 192, 48},
+ { 192, 45},
+ { 191, 43},
+ { 191, 40},
+ { 190, 38},
+ { 190, 35},
+ { 189, 33},
+ { 188, 30},
+ { 187, 28},
+ { 186, 25},
+ { 185, 23},
+ { 184, 20},
+ { 183, 18},
+ { 182, 15},
+ { 181, 13},
+ { 180, 10},
+ { 179, 8},
+ { 178, 5},
+ { 0, 0},
+};
+
+static const struct battery_thresh corgi_battery_levels_noac[] = {
+ { 213, 100},
+ { 212, 98},
+ { 211, 95},
+ { 210, 93},
+ { 209, 90},
+ { 208, 88},
+ { 207, 85},
+ { 206, 83},
+ { 205, 80},
+ { 204, 78},
+ { 203, 75},
+ { 202, 73},
+ { 201, 70},
+ { 200, 68},
+ { 199, 65},
+ { 198, 63},
+ { 197, 60},
+ { 196, 58},
+ { 195, 55},
+ { 194, 53},
+ { 193, 50},
+ { 192, 48},
+ { 191, 45},
+ { 190, 43},
+ { 189, 40},
+ { 188, 38},
+ { 187, 35},
+ { 186, 33},
+ { 185, 30},
+ { 184, 28},
+ { 183, 25},
+ { 182, 23},
+ { 181, 20},
+ { 180, 18},
+ { 179, 15},
+ { 178, 13},
+ { 177, 10},
+ { 176, 8},
+ { 175, 5},
+ { 0, 0},
+};
+
static void corgi_charger_init(void)
{
pxa_gpio_mode(CORGI_GPIO_ADC_TEMP_ON | GPIO_OUT);
@@ -214,8 +300,8 @@
.fatal_acin_volt = SHARPSL_FATAL_ACIN_VOLT,
.fatal_noacin_volt= SHARPSL_FATAL_NOACIN_VOLT,
.bat_levels = 40,
- .bat_levels_noac = spitz_battery_levels_noac,
- .bat_levels_acin = spitz_battery_levels_acin,
+ .bat_levels_noac = corgi_battery_levels_noac,
+ .bat_levels_acin = corgi_battery_levels_acin,
.status_high_acin = 188,
.status_low_acin = 178,
.status_high_noac = 185,
diff -ur ./arch/arm.ofic/mach-pxa/sharpsl.h ./arch/arm/mach-pxa/sharpsl.h
--- ./arch/arm.ofic/mach-pxa/sharpsl.h 2009-09-10 00:13:59.000000000 +0200
+++ ./arch/arm/mach-pxa/sharpsl.h 2009-10-14 12:12:13.000000000 +0200
@@ -42,8 +42,23 @@
#define MAX1111_BATT_TEMP 2u
#define MAX1111_ACIN_VOLT 6u
-extern struct battery_thresh spitz_battery_levels_acin[];
-extern struct battery_thresh spitz_battery_levels_noac[];
int sharpsl_pm_pxa_read_max1111(int channel);
+/*
+ * Constants
+ */
+#define SHARPSL_CHARGE_ON_TIME_INTERVAL (msecs_to_jiffies(1*60*1000)) /* 1 min */
+#define SHARPSL_CHARGE_FINISH_TIME (msecs_to_jiffies(10*60*1000)) /* 10 min */
+#define SHARPSL_BATCHK_TIME (msecs_to_jiffies(15*1000)) /* 15 sec */
+#define SHARPSL_BATCHK_TIME_SUSPEND (60*10) /* 10 min */
+
+#define SHARPSL_WAIT_CO_TIME 15 /* 15 sec */
+#define SHARPSL_WAIT_DISCHARGE_ON 100 /* 100 msec */
+#define SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP 10 /* 10 msec */
+#define SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT 10 /* 10 msec */
+#define SHARPSL_CHECK_BATTERY_WAIT_TIME_ACIN 10 /* 10 msec */
+#define SHARPSL_CHARGE_WAIT_TIME 15 /* 15 msec */
+#define SHARPSL_CHARGE_CO_CHECK_TIME 5 /* 5 msec */
+#define SHARPSL_CHARGE_RETRY_CNT 1 /* eqv. 10 min */
+
Only in ./arch/arm/mach-pxa: sharpsl.h~
diff -ur ./arch/arm.ofic/mach-pxa/sharpsl_pm.c ./arch/arm/mach-pxa/sharpsl_pm.c
--- ./arch/arm.ofic/mach-pxa/sharpsl_pm.c 2009-10-06 13:48:07.000000000 +0200
+++ ./arch/arm/mach-pxa/sharpsl_pm.c 2009-10-14 12:12:05.000000000 +0200
@@ -32,25 +32,10 @@
#include <mach/regs-rtc.h>
#include <mach/sharpsl.h>
#include <mach/sharpsl_pm.h>
+#include <mach/spitz.h>
#include "sharpsl.h"
-/*
- * Constants
- */
-#define SHARPSL_CHARGE_ON_TIME_INTERVAL (msecs_to_jiffies(1*60*1000)) /* 1 min */
-#define SHARPSL_CHARGE_FINISH_TIME (msecs_to_jiffies(10*60*1000)) /* 10 min */
-#define SHARPSL_BATCHK_TIME (msecs_to_jiffies(15*1000)) /* 15 sec */
-#define SHARPSL_BATCHK_TIME_SUSPEND (60*10) /* 10 min */
-
-#define SHARPSL_WAIT_CO_TIME 15 /* 15 sec */
-#define SHARPSL_WAIT_DISCHARGE_ON 100 /* 100 msec */
-#define SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP 10 /* 10 msec */
-#define SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT 10 /* 10 msec */
-#define SHARPSL_CHECK_BATTERY_WAIT_TIME_ACIN 10 /* 10 msec */
-#define SHARPSL_CHARGE_WAIT_TIME 15 /* 15 msec */
-#define SHARPSL_CHARGE_CO_CHECK_TIME 5 /* 5 msec */
-#define SHARPSL_CHARGE_RETRY_CNT 1 /* eqv. 10 min */
/*
* Prototypes
@@ -72,112 +57,28 @@
* Variables
*/
struct sharpsl_pm_status sharpsl_pm;
+EXPORT_SYMBOL(sharpsl_pm);
static DECLARE_DELAYED_WORK(toggle_charger, sharpsl_charge_toggle);
static DECLARE_DELAYED_WORK(sharpsl_bat, sharpsl_battery_thread);
DEFINE_LED_TRIGGER(sharpsl_charge_led_trigger);
-struct battery_thresh spitz_battery_levels_acin[] = {
- { 213, 100},
- { 212, 98},
- { 211, 95},
- { 210, 93},
- { 209, 90},
- { 208, 88},
- { 207, 85},
- { 206, 83},
- { 205, 80},
- { 204, 78},
- { 203, 75},
- { 202, 73},
- { 201, 70},
- { 200, 68},
- { 199, 65},
- { 198, 63},
- { 197, 60},
- { 196, 58},
- { 195, 55},
- { 194, 53},
- { 193, 50},
- { 192, 48},
- { 192, 45},
- { 191, 43},
- { 191, 40},
- { 190, 38},
- { 190, 35},
- { 189, 33},
- { 188, 30},
- { 187, 28},
- { 186, 25},
- { 185, 23},
- { 184, 20},
- { 183, 18},
- { 182, 15},
- { 181, 13},
- { 180, 10},
- { 179, 8},
- { 178, 5},
- { 0, 0},
-};
-
-struct battery_thresh spitz_battery_levels_noac[] = {
- { 213, 100},
- { 212, 98},
- { 211, 95},
- { 210, 93},
- { 209, 90},
- { 208, 88},
- { 207, 85},
- { 206, 83},
- { 205, 80},
- { 204, 78},
- { 203, 75},
- { 202, 73},
- { 201, 70},
- { 200, 68},
- { 199, 65},
- { 198, 63},
- { 197, 60},
- { 196, 58},
- { 195, 55},
- { 194, 53},
- { 193, 50},
- { 192, 48},
- { 191, 45},
- { 190, 43},
- { 189, 40},
- { 188, 38},
- { 187, 35},
- { 186, 33},
- { 185, 30},
- { 184, 28},
- { 183, 25},
- { 182, 23},
- { 181, 20},
- { 180, 18},
- { 179, 15},
- { 178, 13},
- { 177, 10},
- { 176, 8},
- { 175, 5},
- { 0, 0},
-};
-
/* MAX1111 Commands */
-#define MAXCTRL_PD0 1u << 0
-#define MAXCTRL_PD1 1u << 1
-#define MAXCTRL_SGL 1u << 2
-#define MAXCTRL_UNI 1u << 3
+#define MAXCTRL_PD0 (1u << 0)
+#define MAXCTRL_PD1 (1u << 1)
+#define MAXCTRL_SGL (1u << 2)
+#define MAXCTRL_UNI (1u << 3)
#define MAXCTRL_SEL_SH 4
-#define MAXCTRL_STR 1u << 7
+#define MAXCTRL_STR (1u << 7)
/*
* Read MAX1111 ADC
*/
int sharpsl_pm_pxa_read_max1111(int channel)
{
- if (machine_is_tosa()) // Ugly, better move this function into another module
+ /* Ugly, better move this function into another module */
+ if (machine_is_tosa())
return 0;
#ifdef CONFIG_CORGI_SSP_DEPRECATED
@@ -193,7 +94,7 @@
#endif
}
-static int get_percentage(int voltage)
+int get_percentage(int voltage)
{
int i = sharpsl_pm.machinfo->bat_levels - 1;
int bl_status = sharpsl_pm.machinfo->backlight_get_status ? sharpsl_pm.machinfo->backlight_get_status() : 0;
@@ -209,6 +110,7 @@
return thresh[i].percentage;
}
+EXPORT_SYMBOL(get_percentage);
static int get_apm_status(int voltage)
{
@@ -238,7 +140,7 @@
static void sharpsl_battery_thread(struct work_struct *private_)
{
- int voltage, percent, apm_status, i = 0;
+ int voltage, percent, apm_status, i;
if (!sharpsl_pm.machinfo)
return;
@@ -250,15 +152,14 @@
&& time_after(jiffies, sharpsl_pm.charge_start_time + SHARPSL_CHARGE_ON_TIME_INTERVAL))
schedule_delayed_work(&toggle_charger, 0);
- while(1) {
+ for (i = 0; i < 5; i++) {
voltage = sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_VOLT);
-
- if (voltage > 0) break;
- if (i++ > 5) {
- voltage = sharpsl_pm.machinfo->bat_levels_noac[0].voltage;
- dev_warn(sharpsl_pm.dev, "Warning: Cannot read main battery!\n");
+ if (voltage > 0)
break;
- }
+ }
+ if (voltage <= 0) {
+ voltage = sharpsl_pm.machinfo->bat_levels_noac[0].voltage;
+ dev_warn(sharpsl_pm.dev, "Warning: Cannot read main battery!\n");
}
voltage = sharpsl_average_value(voltage);
@@ -266,8 +167,10 @@
percent = get_percentage(voltage);
/* At low battery voltages, the voltage has a tendency to start
- creeping back up so we try to avoid this here */
- if ((sharpsl_pm.battstat.ac_status == APM_AC_ONLINE) || (apm_status == APM_BATTERY_STATUS_HIGH) || percent <= sharpsl_pm.battstat.mainbat_percent) {
+ creeping back up so we try to avoid this here */
+ if ((sharpsl_pm.battstat.ac_status == APM_AC_ONLINE)
+ || (apm_status == APM_BATTERY_STATUS_HIGH)
+ || percent <= sharpsl_pm.battstat.mainbat_percent) {
sharpsl_pm.battstat.mainbat_voltage = voltage;
sharpsl_pm.battstat.mainbat_status = apm_status;
sharpsl_pm.battstat.mainbat_percent = percent;
@@ -279,8 +182,8 @@
#ifdef CONFIG_BACKLIGHT_CORGI
/* If battery is low. limit backlight intensity to save power. */
if ((sharpsl_pm.battstat.ac_status != APM_AC_ONLINE)
- && ((sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_LOW) ||
- (sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_CRITICAL))) {
+ && ((sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_LOW)
+ || (sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_CRITICAL))) {
if (!(sharpsl_pm.flags & SHARPSL_BL_LIMIT)) {
sharpsl_pm.machinfo->backlight_limit(1);
sharpsl_pm.flags |= SHARPSL_BL_LIMIT;
@@ -293,8 +196,8 @@
/* Suspend if critical battery level */
if ((sharpsl_pm.battstat.ac_status != APM_AC_ONLINE)
- && (sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_CRITICAL)
- && !(sharpsl_pm.flags & SHARPSL_APM_QUEUED)) {
+ && (sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_CRITICAL)
+ && !(sharpsl_pm.flags & SHARPSL_APM_QUEUED)) {
sharpsl_pm.flags |= SHARPSL_APM_QUEUED;
dev_err(sharpsl_pm.dev, "Fatal Off\n");
apm_queue_event(APM_CRITICAL_SUSPEND);
@@ -339,6 +242,8 @@
static void sharpsl_charge_error(void)
{
+ dev_warn(sharpsl_pm.dev, "Charger Error\n");
+
sharpsl_pm_led(SHARPSL_LED_ERROR);
sharpsl_pm.machinfo->charge(0);
sharpsl_pm.charge_mode = CHRG_ERROR;
@@ -346,7 +251,7 @@
static void sharpsl_charge_toggle(struct work_struct *private_)
{
- dev_dbg(sharpsl_pm.dev, "Toogling Charger at time: %lx\n", jiffies);
+ dev_dbg(sharpsl_pm.dev, "Toggling Charger at time: %lx\n", jiffies);
if (!sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN)) {
sharpsl_charge_off();
@@ -368,7 +273,7 @@
{
int acin = sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN);
- dev_dbg(sharpsl_pm.dev, "AC Status: %d\n",acin);
+ dev_dbg(sharpsl_pm.dev, "AC Status: %d\n", acin);
sharpsl_average_clear();
if (acin && (sharpsl_pm.charge_mode != CHRG_ON))
@@ -472,14 +377,14 @@
sharpsl_ad[sharpsl_ad_index] = ad;
sharpsl_ad_index++;
if (sharpsl_ad_index >= SHARPSL_CNV_VALUE_NUM) {
- for (i=0; i < (SHARPSL_CNV_VALUE_NUM-1); i++)
+ for (i = 0; i < (SHARPSL_CNV_VALUE_NUM-1); i++)
sharpsl_ad[i] = sharpsl_ad[i+1];
sharpsl_ad_index = SHARPSL_CNV_VALUE_NUM - 1;
}
- for (i=0; i < sharpsl_ad_index; i++)
+ for (i = 0; i < sharpsl_ad_index; i++)
ad_val += sharpsl_ad[i];
- return (ad_val / sharpsl_ad_index);
+ return ad_val / sharpsl_ad_index;
}
/*
@@ -492,8 +397,8 @@
/* Find MAX val */
temp = val[0];
- j=0;
- for (i=1; i<5; i++) {
+ j = 0;
+ for (i = 1; i < 5; i++) {
if (temp < val[i]) {
temp = val[i];
j = i;
@@ -502,21 +407,21 @@
/* Find MIN val */
temp = val[4];
- k=4;
- for (i=3; i>=0; i--) {
+ k = 4;
+ for (i = 3; i >= 0; i--) {
if (temp > val[i]) {
temp = val[i];
k = i;
}
}
- for (i=0; i<5; i++)
- if (i != j && i != k )
+ for (i = 0; i < 5; i++)
+ if (i != j && i != k)
sum += val[i];
dev_dbg(sharpsl_pm.dev, "Average: %d from values: %d, %d, %d, %d, %d\n", sum/3, val[0], val[1], val[2], val[3], val[4]);
- return (sum/3);
+ return sum/3;
}
static int sharpsl_check_battery_temp(void)
@@ -524,7 +429,7 @@
int val, i, buff[5];
/* Check battery temperature */
- for (i=0; i<5; i++) {
+ for (i = 0; i < 5; i++) {
mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
sharpsl_pm.machinfo->measure_temp(1);
mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
@@ -535,8 +440,10 @@
val = get_select_val(buff);
dev_dbg(sharpsl_pm.dev, "Temperature: %d\n", val);
- if (val > sharpsl_pm.machinfo->charge_on_temp) {
- printk(KERN_WARNING "Not charging: temperature out of limits.\n");
+ /* FIXME: this should catch battery read errors, but we should
+ probably avoid charging in <0C temperatures, too. */
+ if ((val < 0) || (val > sharpsl_pm.machinfo->charge_on_temp)) {
+ dev_warn(sharpsl_pm.dev, "Not charging: temperature %d out of limits.\n", val);
return -1;
}
@@ -557,7 +464,7 @@
sharpsl_pm.machinfo->discharge1(1);
/* Check battery voltage */
- for (i=0; i<5; i++) {
+ for (i = 0; i < 5; i++) {
buff[i] = sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_VOLT);
mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT);
}
@@ -581,16 +488,16 @@
{
int temp, i, buff[5];
- for (i=0; i<5; i++) {
+ for (i = 0; i < 5; i++) {
buff[i] = sharpsl_pm.machinfo->read_devdata(SHARPSL_ACIN_VOLT);
mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_ACIN);
}
temp = get_select_val(buff);
- dev_dbg(sharpsl_pm.dev, "AC Voltage: %d\n",temp);
+ dev_dbg(sharpsl_pm.dev, "AC Voltage: %d\n", temp);
if ((temp > sharpsl_pm.machinfo->charge_acin_high) || (temp < sharpsl_pm.machinfo->charge_acin_low)) {
- dev_err(sharpsl_pm.dev, "Error: AC check failed.\n");
+ dev_err(sharpsl_pm.dev, "Error: AC check failed: voltage %d.\n", temp);
return -1;
}
@@ -624,9 +531,9 @@
static void corgi_goto_sleep(unsigned long alarm_time, unsigned int alarm_enable, suspend_state_t state)
{
- dev_dbg(sharpsl_pm.dev, "Time is: %08x\n",RCNR);
+ dev_dbg(sharpsl_pm.dev, "Time is: %08x\n", RCNR);
- dev_dbg(sharpsl_pm.dev, "Offline Charge Activate = %d\n",sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG);
+ dev_dbg(sharpsl_pm.dev, "Offline Charge Activate = %d\n", sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG);
/* not charging and AC-IN! */
if ((sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG) && (sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN))) {
@@ -644,12 +551,12 @@
if ((sharpsl_pm.charge_mode == CHRG_ON) && ((alarm_enable && ((alarm_time - RCNR) > (SHARPSL_BATCHK_TIME_SUSPEND + 30))) || !alarm_enable)) {
RTSR &= RTSR_ALE;
RTAR = RCNR + SHARPSL_BATCHK_TIME_SUSPEND;
- dev_dbg(sharpsl_pm.dev, "Charging alarm at: %08x\n",RTAR);
+ dev_dbg(sharpsl_pm.dev, "Charging alarm at: %08x\n", RTAR);
sharpsl_pm.flags |= SHARPSL_ALARM_ACTIVE;
} else if (alarm_enable) {
RTSR &= RTSR_ALE;
RTAR = alarm_time;
- dev_dbg(sharpsl_pm.dev, "User alarm at: %08x\n",RTAR);
+ dev_dbg(sharpsl_pm.dev, "User alarm at: %08x\n", RTAR);
} else {
dev_dbg(sharpsl_pm.dev, "No alarms set.\n");
}
@@ -658,19 +565,20 @@
sharpsl_pm.machinfo->postsuspend();
- dev_dbg(sharpsl_pm.dev, "Corgi woken up from suspend: %08x\n",PEDR);
+
+ dev_dbg(sharpsl_pm.dev, "Corgi woken up from suspend: %08x\n", PEDR);
}
static int corgi_enter_suspend(unsigned long alarm_time, unsigned int alarm_enable, suspend_state_t state)
{
- if (!sharpsl_pm.machinfo->should_wakeup(!(sharpsl_pm.flags & SHARPSL_ALARM_ACTIVE) && alarm_enable) )
- {
+ return 0;
+ if (!sharpsl_pm.machinfo->should_wakeup(!(sharpsl_pm.flags & SHARPSL_ALARM_ACTIVE) && alarm_enable)) {
if (!(sharpsl_pm.flags & SHARPSL_ALARM_ACTIVE)) {
dev_dbg(sharpsl_pm.dev, "No user triggered wakeup events and not charging. Strange. Suspend.\n");
corgi_goto_sleep(alarm_time, alarm_enable, state);
return 1;
}
- if(sharpsl_off_charge_battery()) {
+ if (sharpsl_off_charge_battery()) {
dev_dbg(sharpsl_pm.dev, "Charging. Suspend...\n");
corgi_goto_sleep(alarm_time, alarm_enable, state);
return 1;
@@ -697,7 +605,7 @@
corgi_goto_sleep(alarm_time, alarm_status, state);
- while (corgi_enter_suspend(alarm_time,alarm_status,state))
+ while (corgi_enter_suspend(alarm_time, alarm_status, state))
{}
if (sharpsl_pm.machinfo->earlyresume)
@@ -732,7 +640,7 @@
sharpsl_pm.machinfo->discharge1(1);
/* Check battery : check inserting battery ? */
- for (i=0; i<5; i++) {
+ for (i = 0; i < 5; i++) {
buff[i] = sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_VOLT);
mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT);
}
@@ -812,7 +720,7 @@
mdelay(SHARPSL_CHARGE_CO_CHECK_TIME);
time = RCNR;
- while(1) {
+ while (1) {
/* Check if any wakeup event had occurred */
if (sharpsl_pm.machinfo->charger_wakeup() != 0)
return 0;
@@ -835,9 +743,9 @@
mdelay(SHARPSL_CHARGE_CO_CHECK_TIME);
time = RCNR;
- while(1) {
+ while (1) {
/* Check if any wakeup event had occurred */
- if (sharpsl_pm.machinfo->charger_wakeup() != 0)
+ if (sharpsl_pm.machinfo->charger_wakeup())
return 0;
/* Check for timeout */
if ((RCNR-time) > SHARPSL_WAIT_CO_TIME) {
@@ -864,12 +772,12 @@
static ssize_t battery_percentage_show(struct device *dev, struct device_attribute *attr, char *buf)
{
- return sprintf(buf, "%d\n",sharpsl_pm.battstat.mainbat_percent);
+ return sprintf(buf, "%d\n", sharpsl_pm.battstat.mainbat_percent);
}
static ssize_t battery_voltage_show(struct device *dev, struct device_attribute *attr, char *buf)
{
- return sprintf(buf, "%d\n",sharpsl_pm.battstat.mainbat_voltage);
+ return sprintf(buf, "%d\n", sharpsl_pm.battstat.mainbat_voltage);
}
static DEVICE_ATTR(battery_percentage, 0444, battery_percentage_show, NULL);
@@ -943,7 +851,6 @@
}
}
- if (sharpsl_pm.machinfo->batfull_irq)
- {
+ if (sharpsl_pm.machinfo->batfull_irq) {
/* Register interrupt handler. */
if (request_irq(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batfull), sharpsl_chrg_full_isr, IRQF_DISABLED | IRQF_TRIGGER_RISING, "CO", sharpsl_chrg_full_isr)) {
diff -ur ./arch/arm.ofic/mach-pxa/spitz.c ./arch/arm/mach-pxa/spitz.c
--- ./arch/arm.ofic/mach-pxa/spitz.c 2009-10-06 13:48:07.000000000 +0200
+++ ./arch/arm/mach-pxa/spitz.c 2009-10-14 11:01:36.000000000 +0200
@@ -686,12 +733,19 @@
.dev.platform_data = &sharpsl_rom_data,
};
+static struct platform_device spitz_battery_device = {
+ .name = "spitz-battery",
+ .id = -1,
+};
+
+
static struct platform_device *devices[] __initdata = {
&spitzscoop_device,
&spitzkbd_device,
&spitzled_device,
&sharpsl_nand_device,
&sharpsl_rom_device,
+ &spitz_battery_device,
};
static void spitz_poweroff(void)
--- ./arch/arm.ofic/mach-pxa/spitz_pm.c 2009-09-10 00:13:59.000000000 +0200
+++ ./arch/arm/mach-pxa/spitz_pm.c 2009-10-19 07:28:42.000000000 +0200
@@ -37,6 +37,93 @@
static int spitz_last_ac_status;
+static const struct battery_thresh spitz_battery_levels_acin[] = {
+ { 213, 100},
+ { 212, 98},
+ { 211, 95},
+ { 210, 93},
+ { 209, 90},
+ { 208, 88},
+ { 207, 85},
+ { 206, 83},
+ { 205, 80},
+ { 204, 78},
+ { 203, 75},
+ { 202, 73},
+ { 201, 70},
+ { 200, 68},
+ { 199, 65},
+ { 198, 63},
+ { 197, 60},
+ { 196, 58},
+ { 195, 55},
+ { 194, 53},
+ { 193, 50},
+ { 192, 48},
+ { 192, 45},
+ { 191, 43},
+ { 191, 40},
+ { 190, 38},
+ { 190, 35},
+ { 189, 33},
+ { 188, 30},
+ { 187, 28},
+ { 186, 25},
+ { 185, 23},
+ { 184, 20},
+ { 183, 18},
+ { 182, 15},
+ { 181, 13},
+ { 180, 10},
+ { 179, 8},
+ { 178, 5},
+ { 0, 0},
+};
+
+static const struct battery_thresh spitz_battery_levels_noac[] = {
+ { 213, 100},
+ { 212, 98},
+ { 211, 95},
+ { 210, 93},
+ { 209, 90},
+ { 208, 88},
+ { 207, 85},
+ { 206, 83},
+ { 205, 80},
+ { 204, 78},
+ { 203, 75},
+ { 202, 73},
+ { 201, 70},
+ { 200, 68},
+ { 199, 65},
+ { 198, 63},
+ { 197, 60},
+ { 196, 58},
+ { 195, 55},
+ { 194, 53},
+ { 193, 50},
+ { 192, 48},
+ { 191, 45},
+ { 190, 43},
+ { 189, 40},
+ { 188, 38},
+ { 187, 35},
+ { 186, 33},
+ { 185, 30},
+ { 184, 28},
+ { 183, 25},
+ { 182, 23},
+ { 181, 20},
+ { 180, 18},
+ { 179, 15},
+ { 178, 13},
+ { 177, 10},
+ { 176, 8},
+ { 175, 5},
+ { 0, 0},
+};
+
+
static void spitz_charger_init(void)
{
pxa_gpio_mode(SPITZ_GPIO_KEY_INT | GPIO_IN);
@@ -103,7 +190,7 @@
PFER = GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET);
PWER = GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET) | PWER_RTC;
PKWR = GPIO_bit(SPITZ_GPIO_SYNC) | GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET);
- PKSR = 0xffffffff; // clear
+ PKSR = 0xffffffff; /* clear */
/* nRESET_OUT Disable */
PSLR |= PSLR_SL_ROD;
@@ -149,7 +236,7 @@
if (resume_on_alarm && (PEDR & PWER_RTC))
is_resume |= PWER_RTC;
- dev_dbg(sharpsl_pm.dev, "is_resume: %x\n",is_resume);
+ dev_dbg(sharpsl_pm.dev, "is_resume: %x\n", is_resume);
return is_resume;
}
@@ -160,15 +247,15 @@
unsigned long spitzpm_read_devdata(int type)
{
- switch(type) {
+ switch (type) {
case SHARPSL_STATUS_ACIN:
return (((~GPLR(SPITZ_GPIO_AC_IN)) & GPIO_bit(SPITZ_GPIO_AC_IN)) != 0);
case SHARPSL_STATUS_LOCK:
- return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batlock);
+ return !!READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batlock);
case SHARPSL_STATUS_CHRGFULL:
- return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batfull);
+ return !!READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batfull);
case SHARPSL_STATUS_FATAL:
- return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_fatal);
+ return !!READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_fatal);
case SHARPSL_ACIN_VOLT:
return sharpsl_pm_pxa_read_max1111(MAX1111_ACIN_VOLT);
case SHARPSL_BATT_TEMP:
@@ -179,6 +266,11 @@
}
}
+int backlight_get_status(void)
+{
+ return 0;
+}
+
struct sharpsl_charger_machinfo spitz_pm_machinfo = {
.init = spitz_charger_init,
.exit = NULL,
@@ -199,8 +291,9 @@
#if defined(CONFIG_LCD_CORGI)
.backlight_limit = corgi_lcd_limit_intensity,
#elif defined(CONFIG_BACKLIGHT_CORGI)
- .backlight_limit = corgibl_limit_intensity,
+ .backlight_limit = corgibl_limit_intensity,
#endif
+// .backlight_get_status = backlight_get_status,
.charge_on_volt = SHARPSL_CHARGE_ON_VOLT,
.charge_on_temp = SHARPSL_CHARGE_ON_TEMP,
.charge_acin_high = SHARPSL_CHARGE_ON_ACIN_HIGH,
@@ -241,7 +334,7 @@
static void spitzpm_exit(void)
{
- platform_device_unregister(spitzpm_device);
+ platform_device_unregister(spitzpm_device);
}
module_init(spitzpm_init);
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
^ permalink raw reply [flat|nested] 5+ messages in thread
* spitz battery driver
2009-11-09 13:58 spitz battery driver Pavel Machek
@ 2009-11-10 3:48 ` Eric Miao
2009-11-10 10:46 ` Pavel Machek
0 siblings, 1 reply; 5+ messages in thread
From: Eric Miao @ 2009-11-10 3:48 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Nov 9, 2009 at 9:58 PM, Pavel Machek <pavel@ucw.cz> wrote:
> Hi!
>
> This introduces battery driver for spitz. For now it is
> monitoring&debug-only.
>
This is a good move. However, I assume the patch is still RFC now.
Or basically the coding style cleanup can be separated into another
patch?
> Signed-off-by: Pavel Machek <pavel@ucw.cz> (but not meant for merge)
>
> --- ./drivers/power.ofic/Makefile ? ? ? 2009-10-06 13:51:29.000000000 +0200
> +++ ./drivers/power/Makefile ? ?2009-10-11 16:12:09.000000000 +0200
> @@ -24,6 +24,7 @@
> ?obj-$(CONFIG_BATTERY_PMU) ? ? ?+= pmu_battery.o
> ?obj-$(CONFIG_BATTERY_OLPC) ? ? += olpc_battery.o
> ?obj-$(CONFIG_BATTERY_TOSA) ? ? += tosa_battery.o
> +obj-m ?+= spitz_battery.o
> ?obj-$(CONFIG_BATTERY_WM97XX) ? += wm97xx_battery.o
> ?obj-$(CONFIG_BATTERY_BQ27x00) ?+= bq27x00_battery.o
> ?obj-$(CONFIG_BATTERY_DA9030) ? += da9030_battery.o
> diff -ur ./drivers/power.ofic/power_supply_sysfs.c ./drivers/power/power_supply_sysfs.c
> --- ./drivers/power.ofic/power_supply_sysfs.c ? 2009-10-06 13:51:29.000000000 +0200
> +++ ./drivers/power/power_supply_sysfs.c ? ? ? ?2009-10-15 05:45:46.000000000 +0200
> @@ -39,7 +39,8 @@
>
> ?static ssize_t power_supply_show_property(struct device *dev,
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?struct device_attribute *attr,
> - ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? char *buf) {
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? char *buf)
> +{
> ? ? ? ?static char *status_text[] = {
> ? ? ? ? ? ? ? ?"Unknown", "Charging", "Discharging", "Not charging", "Full"
> ? ? ? ?};
> @@ -135,7 +136,8 @@
>
> ?static ssize_t power_supply_show_static_attrs(struct device *dev,
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?struct device_attribute *attr,
> - ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? char *buf) {
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? char *buf)
> +{
> ? ? ? ?static char *type_text[] = { "Battery", "UPS", "Mains", "USB" };
> ? ? ? ?struct power_supply *psy = dev_get_drvdata(dev);
>
> diff -ur ./drivers/power.ofic/spitz_battery.c ./drivers/power/spitz_battery.c
> --- ./drivers/power.ofic/spitz_battery.c ? ? ? ?2009-10-11 16:14:11.000000000 +0200
> +++ ./drivers/power/spitz_battery.c ? ? 2009-10-22 07:27:52.000000000 +0200
> @@ -0,0 +1,430 @@
> +/*
> + * Battery and Power Management code for the Sharp SL-3000c
> + *
> + * Copyright (c) 2009 Pavel Machek <pavel@ucw.cz>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * Li-ion batteries are angry beasts, and they like to explode.
> + * If angry lithium comes your way, the hw was misdesigned.
> + *
> + */
> +#include <linux/platform_device.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/power_supply.h>
> +#include <linux/delay.h>
> +#include <linux/spinlock.h>
> +#include <linux/interrupt.h>
> +#include <linux/gpio.h>
> +
> +#include <asm/mach-types.h>
> +#include <mach/spitz.h>
> +#include <mach/sharpsl.h>
> +#include <mach/sharpsl_pm.h>
> +
> +#include "../../arch/arm/mach-pxa/sharpsl.h"
> +
> +extern struct sharpsl_pm_status sharpsl_pm;
> +
> +
> +struct spitz_bat {
> + ? ? ? struct power_supply psy;
> +
> + ? ? ? bool (*is_present)(struct spitz_bat *bat);
> +};
> +
> +static struct spitz_bat spitz_bat_main, spitz_ac;
> +
> +extern int sharpsl_pm_pxa_read_max1111(int channel);
> +
> +int basic_current = 125; /* miliAmp */
> +int battery_resistance = 422; /* miliOhm */
> +
> +/* 422 seems to be suitable for very old, 1Ah battery.
> + ? 2Ah battery probably has better resistance */
> +
> +/* Unfortunately, resistance depends on state of charge, current
> + * direction and temperature.
> + *
> + * Ouch, and dependency is actually _not_ too simple. It is lowest
> + * at 3.55V, very slowly rises at 4V (approximately linear dependency),
> + * and quickly rises towards 3.2V (in something exponential-looking).
> + *
> + * It is about same at 25Celsius and 40Celsius, and about 2.5x the value
> + * on 0Celsius, rising _very_ sharply.
> + *
> + * Li-ion should only be charged between 0 and 45 Celsius, and discharged
> + * between -20 and 60 celsius.
> + */
> +
> +extern int backlight_current;
> +
> +int battery_current(void)
> +{
> + ? ? ? int intensity = sharpsl_pm.machinfo->backlight_get_status ? sharpsl_pm.machinfo->backlight_get_status() : 0;
> +
> + ? ? ? return basic_current + backlight_current;
> +}
> +
> +int liion_internal_voltage(int voltage, int current_ma)
> +{
> + ? ? ? return voltage + (battery_resistance * current_ma / 1000);
> +}
> +
> +int liion_expected_voltage(int internal_voltage, int current_ma)
> +{
> + ? ? ? return internal_voltage - (battery_resistance * current_ma / 1000);
> +}
> +
> +/* returns mV */
> +int liion_voltage(void)
> +{
> + ? ? ? /* Thanks to Stanislav B. ADC has 3.3V as reference,
> + ? ? ? ? ?is connected to battery over 47kOhm,
> + ? ? ? ? ?and to ground over 100kOhm. */
> + ? ? ? return (sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_VOLT) * 147 * 33)/256;
> +}
> +
> +/* See for example http://www.kokam.com/english/biz/rc.html for
> + * voltage/capacity characteristic. I assume it is going to be
> + * reasonably similar to li-ion used in collie.
> + *
> + */
> +
> +/*
> + { 420, 100 },
> + { 417, 95 }, means it will report 100% between 418 and 420
> + */
> +
> +struct battery_thresh battery_levels[] = {
> + ? ? ? { 3980, 100 },
> + ? ? ? { 3900, 95 },
> + ? ? ? { 3860, 90 },
> + ? ? ? { 3800, 85 },
> + ? ? ? { 3760, 80 },
> + ? ? ? { 3720, 74 },
> + ? ? ? { 3680, 69 },
> + ? ? ? { 3620, 65 },
> + ? ? ? { 3570, 59 },
> + ? ? ? { 3560, 55 },
> + ? ? ? { 3550, 48 },
> + ? ? ? { 3530, 45 },
> + ? ? ? { 3510, 39 },
> + ? ? ? { 3490, 33 },
> + ? ? ? { 3470, 29 },
> + ? ? ? { 3450, 23 },
> + ? ? ? { 3410, 16 },
> + ? ? ? { ? ?0, 0 },
> +};
> +
> +int get_percentage(void)
> +{
> + ? ? ? int i = ARRAY_SIZE(battery_levels);
> + ? ? ? struct battery_thresh *thresh;
> + ? ? ? int voltage = liion_internal_voltage(liion_voltage(), battery_current());
> +
> + ? ? ? thresh = battery_levels;
> +
> + ? ? ? while (i > 0 && (voltage > thresh[i].voltage))
> + ? ? ? ? ? ? ? i--;
> +
> + ? ? ? return thresh[i].percentage;
> +}
> +
> +static int spitz_bat_get_property(struct power_supply *psy,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? enum power_supply_property psp,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? union power_supply_propval *val)
> +{
> + ? ? ? int ret = 0;
> + ? ? ? struct spitz_bat *bat = container_of(psy, struct spitz_bat, psy);
> +
> + ? ? ? val->intval = 0;
> +
> + ? ? ? switch (psp) {
> + ? ? ? case POWER_SUPPLY_PROP_HEALTH:
> + ? ? ? ? ? ? ? /* POWER_SUPPLY_HEALTH_OVERHEAT , POWER_SUPPLY_HEALTH_COLD,
> + ? ? ? ? ? ? ? ? ?POWER_SUPPLY_HEALTH_OVERVOLTAGE, POWER_SUPPLY_HEALTH_UNSPEC_FAILURE, POWER_SUPPLY_HEALTH_GOOD
> + ? ? ? ? ? ? ? ?*/
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_CHARGE_TYPE:
> + ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
> + ? ? ? ? ? ? ? if (gpio_get_value(SPITZ_GPIO_CHRG_ON) == 0) {
> + ? ? ? ? ? ? ? ? ? ? ? if (gpio_get_value(SPITZ_GPIO_JK_B) == 1)
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
> + ? ? ? ? ? ? ? ? ? ? ? else
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
> + ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_STATUS:
> + ? ? ? ? {
> + ? ? ? ? ? ? ? int status = 0;
> +
> + ? ? ? ? ? ? ? if (gpio_get_value(SPITZ_GPIO_CHRG_ON) == 0)
> + ? ? ? ? ? ? ? ? ? ? ? printk("Chrg bit on. ");
> + ? ? ? ? ? ? ? if (gpio_get_value(SPITZ_GPIO_JK_B) == 0)
> + ? ? ? ? ? ? ? ? ? ? ? printk("Slow charge bit on. ");
> +
> + ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
> +
> + ? ? ? ? ? ? ? if (!sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN))
> + ? ? ? ? ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
> + ? ? ? ? ? ? ? else {
> + ? ? ? ? ? ? ? ? ? ? ? if (gpio_get_value(SPITZ_GPIO_CHRG_ON) == 0)
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_STATUS_CHARGING;
> + ? ? ? ? ? ? ? ? ? ? ? if (sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_CHRGFULL))
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_STATUS_FULL;
> + ? ? ? ? ? ? ? }
> +
> + ? ? ? ? ? ? ? printk("ACIN: %d ", sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN));
> + ? ? ? ? ? ? ? printk("Chrgfull: %d ?", sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_CHRGFULL));
> + ? ? ? ? ? ? ? printk("Fatal: %d ?", sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_FATAL));
> + ? ? ? ? ? ? ? printk("ACIN_volt: %d\n", sharpsl_pm.machinfo->read_devdata(SHARPSL_ACIN_VOLT));
> +
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? ? }
> + ? ? ? case POWER_SUPPLY_PROP_TECHNOLOGY:
> + ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_VOLTAGE_NOW:
> + ? ? ? ? ? ? ? val->intval = liion_voltage()*1000;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
> + ? ? ? ? ? ? ? val->intval = 4200000;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
> + ? ? ? ? ? ? ? val->intval = 3400000;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_TEMP:
> + ? ? ? ? ? ? ? mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
> + ? ? ? ? ? ? ? sharpsl_pm.machinfo->measure_temp(1);
> + ? ? ? ? ? ? ? mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
> + ? ? ? ? ? ? ? val->intval = sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_TEMP);
> + ? ? ? ? ? ? ? sharpsl_pm.machinfo->measure_temp(0);
> + ? ? ? ? ? ? ? /* 121: battery finished charging in 22C room */
> + ? ? ? ? ? ? ? /* 141: outside at 6C */
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_MODEL_NAME:
> + ? ? ? ? ? ? ? val->strval = "spitz-battery";
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_PRESENT:
> + ? ? ? ? ? ? ? val->intval = 1;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? ? ? ? ? /* add these */
> + ? ? ? case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
> + ? ? ? ? ? ? ? val->intval = 2000000;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_CAPACITY:
> + ? ? ? ? ? ? ? val->intval = get_percentage();
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_VOLTAGE_AVG:
> + ? ? ? ? ? ? ? val->intval = liion_internal_voltage(liion_voltage(), battery_current())*1000;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_CURRENT_NOW:
> + ? ? ? ? ? ? ? val->intval = battery_current() * 1000;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? default:
> + ? ? ? ? ? ? ? return -EINVAL;
> + ? ? ? }
> + ? ? ? return -EINVAL;
> +}
> +
> +static int spitz_ac_get_property(struct power_supply *psy,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? enum power_supply_property psp,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? union power_supply_propval *val)
> +{
> + ? ? ? int ret = 0;
> + ? ? ? struct spitz_bat *bat = container_of(psy, struct spitz_bat, psy);
> +
> + ? ? ? val->intval = 0;
> +
> + ? ? ? switch (psp) {
> + ? ? ? case POWER_SUPPLY_PROP_STATUS:
> + ? ? ? ? ? ? ? val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_VOLTAGE_NOW:
> + ? ? ? ? ? ? ? /* Thanks to Stanislav B. ADC has 3.3V as reference,
> + ? ? ? ? ? ? ? ? ?is connected to acin over 2kOhm,
> + ? ? ? ? ? ? ? ? ?and to ground over 1kOhm. */
> + ? ? ? ? ? ? ? val->intval = (sharpsl_pm.machinfo->read_devdata(SHARPSL_ACIN_VOLT) * 3000 * 3300)/256;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
> + ? ? ? ? ? ? ? val->intval = 5250000;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
> + ? ? ? ? ? ? ? val->intval = 4750000;
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_MODEL_NAME:
> + ? ? ? ? ? ? ? val->strval = "spitz-power-supply";
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? case POWER_SUPPLY_PROP_PRESENT:
> + ? ? ? ? ? ? ? val->intval = sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN);
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? default:
> + ? ? ? ? ? ? ? return -EINVAL;
> + ? ? ? }
> + ? ? ? return -EINVAL;
> +}
> +
> +static void spitz_bat_external_power_changed(struct power_supply *psy)
> +{
> +}
> +
> +
> +static enum power_supply_property spitz_bat_main_props[] = {
> + ? ? ? POWER_SUPPLY_PROP_STATUS,
> + ? ? ? POWER_SUPPLY_PROP_TECHNOLOGY,
> + ? ? ? POWER_SUPPLY_PROP_VOLTAGE_NOW,
> + ? ? ? POWER_SUPPLY_PROP_VOLTAGE_AVG,
> + ? ? ? POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
> + ? ? ? POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
> + ? ? ? POWER_SUPPLY_PROP_TEMP,
> + ? ? ? POWER_SUPPLY_PROP_PRESENT,
> + ? ? ? POWER_SUPPLY_PROP_CHARGE_TYPE,
> + ? ? ? POWER_SUPPLY_PROP_HEALTH,
> + ? ? ? POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
> + ? ? ? POWER_SUPPLY_PROP_CURRENT_NOW,
> + ? ? ? POWER_SUPPLY_PROP_CAPACITY,
> +};
> +
> +static struct spitz_bat spitz_bat_main = {
> + ? ? ? .psy = {
> + ? ? ? ? ? ? ? .name ? ? ? ? ? = "main-battery",
> + ? ? ? ? ? ? ? .type ? ? ? ? ? = POWER_SUPPLY_TYPE_BATTERY,
> + ? ? ? ? ? ? ? .properties ? ? = spitz_bat_main_props,
> + ? ? ? ? ? ? ? .num_properties = ARRAY_SIZE(spitz_bat_main_props),
> + ? ? ? ? ? ? ? .get_property ? = spitz_bat_get_property,
> + ? ? ? ? ? ? ? .external_power_changed = spitz_bat_external_power_changed,
> + ? ? ? ? ? ? ? .use_for_apm ? ?= 1,
> + ? ? ? },
> +};
> +
> +static enum power_supply_property spitz_ac_props[] = {
> + ? ? ? POWER_SUPPLY_PROP_STATUS,
> + ? ? ? POWER_SUPPLY_PROP_VOLTAGE_NOW,
> + ? ? ? POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
> + ? ? ? POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
> + ? ? ? POWER_SUPPLY_PROP_PRESENT,
> +};
> +
> +static struct spitz_bat spitz_ac = {
> + ? ? ? .psy = {
> + ? ? ? ? ? ? ? .name ? ? ? ? ? = "ac",
> + ? ? ? ? ? ? ? .type ? ? ? ? ? = POWER_SUPPLY_TYPE_MAINS,
> + ? ? ? ? ? ? ? .properties ? ? = spitz_ac_props,
> + ? ? ? ? ? ? ? .num_properties = ARRAY_SIZE(spitz_ac_props),
> + ? ? ? ? ? ? ? .get_property ? = spitz_ac_get_property,
> + ? ? ? },
> +};
> +
> +#ifdef CONFIG_PM
> +static int spitz_bat_suspend(struct platform_device *dev, pm_message_t state)
> +{
> + ? ? ? return 0;
> +}
> +
> +static int spitz_bat_resume(struct platform_device *dev)
> +{
> + ? ? ? return 0;
> +}
> +#else
> +#define spitz_bat_suspend NULL
> +#define spitz_bat_resume NULL
> +#endif
> +
> +
> +static ssize_t spitz_bat_limit_show(struct device *dev,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct device_attribute *attr,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? char *buf)
> +{
> + ? ? ? sprintf(buf, "Hello :-)");
> + ? ? ? return 9;
> +}
> +
> +static ssize_t spitz_bat_limit_store(struct device *dev,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?struct device_attribute *attr,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?const char *buf, size_t count)
> +{
> + ? ? ? if (!strncmp(buf, "fastcharge", 10)) {
> + ? ? ? ? ? ? ? gpio_set_value(SPITZ_GPIO_JK_B, 1);
> + ? ? ? ? ? ? ? gpio_set_value(SPITZ_GPIO_CHRG_ON, 0);
> + ? ? ? ? ? ? ? return 10;
> + ? ? ? }
> + ? ? ? if (!strncmp(buf, "slowcharge", 10)) {
> + ? ? ? ? ? ? ? gpio_set_value(SPITZ_GPIO_JK_B, 0);
> + ? ? ? ? ? ? ? gpio_set_value(SPITZ_GPIO_CHRG_ON, 0);
> + ? ? ? ? ? ? ? return 10;
> + ? ? ? }
> + ? ? ? if (!strncmp(buf, "nonecharge", 10)) {
> + ? ? ? ? ? ? ? gpio_set_value(SPITZ_GPIO_JK_B, 0);
> + ? ? ? ? ? ? ? gpio_set_value(SPITZ_GPIO_CHRG_ON, 1);
> + ? ? ? ? ? ? ? return 10;
> + ? ? ? }
> + ? ? ? return -EINVAL;
> +}
> +
> +
> +static DEVICE_ATTR(limit, S_IRUGO | S_IWUSR, spitz_bat_limit_show, spitz_bat_limit_store);
> +#if 0
> +static struct device_attribute dev_attr_limit = {
> + ? ? ? ?.attr = { .name = "limit", .mode = 0644 },
> + ? ? ? ?.show = spitz_bat_limit_show,
> + ? ? ? ?.store = spitz_bat_limit_store,
> +};
> +#endif
> +
> +static int __devinit spitz_bat_probe(struct platform_device *dev)
> +{
> + ? ? ? int ret;
> + ? ? ? int i;
> +
> + ? ? ? if (!machine_is_spitz())
> + ? ? ? ? ? ? ? return -ENODEV;
> +
> + ? ? ? printk("spitz_bat_probe: register\n");
> + ? ? ? power_supply_register(&dev->dev, &spitz_bat_main.psy);
> + ? ? ? power_supply_register(&dev->dev, &spitz_ac.psy);
> + ? ? ? device_create_file(&dev->dev, &dev_attr_limit);
> +
> + ? ? ? return 0;
> +}
> +
> +static int __devexit spitz_bat_remove(struct platform_device *dev)
> +{
> + ? ? ? int i;
> +
> + ? ? ? device_remove_file(&dev->dev, &dev_attr_limit);
> + ? ? ? power_supply_unregister(&spitz_bat_main.psy);
> + ? ? ? power_supply_unregister(&spitz_ac.psy);
> + ? ? ? return 0;
> +}
> +
> +
> +static struct platform_driver spitz_bat_driver = {
> + ? ? ? .driver.name ? ?= "spitz-battery",
> + ? ? ? .driver.owner ? = THIS_MODULE,
> + ? ? ? .probe ? ? ? ? ?= spitz_bat_probe,
> + ? ? ? .remove ? ? ? ? = __devexit_p(spitz_bat_remove),
> + ? ? ? .suspend ? ? ? ?= spitz_bat_suspend,
> + ? ? ? .resume ? ? ? ? = spitz_bat_resume,
> +};
> +
> +static int __init spitz_bat_init(void)
> +{
> + ? ? ? return platform_driver_register(&spitz_bat_driver);
> +}
> +
> +static void __exit spitz_bat_exit(void)
> +{
> + ? ? ? platform_driver_unregister(&spitz_bat_driver);
> +}
> +
> +module_init(spitz_bat_init);
> +module_exit(spitz_bat_exit);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_AUTHOR("Pavel Machek");
> +MODULE_DESCRIPTION("Spitz battery driver");
> +MODULE_ALIAS("platform:spitz-battery");
> diff -ur ./drivers/video/backlight.ofic/corgi_lcd.c ./drivers/video/backlight/corgi_lcd.c
> --- ./drivers/video/backlight.ofic/corgi_lcd.c ?2009-10-18 18:11:36.000000000 +0200
> +++ ./drivers/video/backlight/corgi_lcd.c ? ? ? 2009-10-18 18:37:09.000000000 +0200
> @@ -388,17 +388,33 @@
> ? ? ? ?.set_mode ? ? ? = corgi_lcd_set_mode,
> ?};
>
> -static int corgi_bl_get_intensity(struct backlight_device *bd)
> +int corgi_bl_get_intensity(struct backlight_device *bd)
> ?{
> ? ? ? ?struct corgi_lcd *lcd = dev_get_drvdata(&bd->dev);
>
> ? ? ? ?return lcd->intensity;
> ?}
> +EXPORT_SYMBOL(corgi_bl_get_intensity);
> +
> +int backlight_current;
> +EXPORT_SYMBOL(backlight_current);
>
> ?static int corgi_bl_set_intensity(struct corgi_lcd *lcd, int intensity)
> ?{
> ? ? ? ?int cont;
>
> + ? ? ? backlight_current = 0;
> + ? ? ? if (intensity > 0)
> + ? ? ? ? ? ? ? backlight_current = 55;
> + ? ? ? if (intensity > 10)
> + ? ? ? ? ? ? ? backlight_current = 115;
> + ? ? ? if (intensity > 20)
> + ? ? ? ? ? ? ? backlight_current = 140;
> + ? ? ? if (intensity > 30)
> + ? ? ? ? ? ? ? backlight_current = 180;
> + ? ? ? if (intensity > 45)
> + ? ? ? ? ? ? ? backlight_current = 245;
> +
> ? ? ? ?if (intensity > 0x10)
> ? ? ? ? ? ? ? ?intensity += 0x10;
>
> @@ -433,8 +449,9 @@
>
> ? ? ? ?if (corgibl_flags & CORGIBL_SUSPENDED)
> ? ? ? ? ? ? ? ?intensity = 0;
> - ? ? ? if (corgibl_flags & CORGIBL_BATTLOW)
> - ? ? ? ? ? ? ? intensity &= lcd->limit_mask;
> +
> + ? ? ? if ((corgibl_flags & CORGIBL_BATTLOW) && intensity > lcd->limit_mask)
> + ? ? ? ? ? ? ? intensity = lcd->limit_mask;
>
> ? ? ? ?return corgi_bl_set_intensity(lcd, intensity);
> ?}
> diff -ur ./arch/arm.ofic/mach-pxa/corgi_pm.c ./arch/arm/mach-pxa/corgi_pm.c
> --- ./arch/arm.ofic/mach-pxa/corgi_pm.c 2009-09-10 00:13:59.000000000 +0200
> +++ ./arch/arm/mach-pxa/corgi_pm.c ? ? ?2009-10-22 19:19:02.000000000 +0200
> @@ -35,6 +35,92 @@
> ?#define SHARPSL_FATAL_ACIN_VOLT ? ? ? ?182 ? /* 3.45V */
> ?#define SHARPSL_FATAL_NOACIN_VOLT ? ? ?170 ? /* 3.40V */
>
> +static const struct battery_thresh corgi_battery_levels_acin[] = {
> + ? ? ? { 213, 100},
> + ? ? ? { 212, ?98},
> + ? ? ? { 211, ?95},
> + ? ? ? { 210, ?93},
> + ? ? ? { 209, ?90},
> + ? ? ? { 208, ?88},
> + ? ? ? { 207, ?85},
> + ? ? ? { 206, ?83},
> + ? ? ? { 205, ?80},
> + ? ? ? { 204, ?78},
> + ? ? ? { 203, ?75},
> + ? ? ? { 202, ?73},
> + ? ? ? { 201, ?70},
> + ? ? ? { 200, ?68},
> + ? ? ? { 199, ?65},
> + ? ? ? { 198, ?63},
> + ? ? ? { 197, ?60},
> + ? ? ? { 196, ?58},
> + ? ? ? { 195, ?55},
> + ? ? ? { 194, ?53},
> + ? ? ? { 193, ?50},
> + ? ? ? { 192, ?48},
> + ? ? ? { 192, ?45},
> + ? ? ? { 191, ?43},
> + ? ? ? { 191, ?40},
> + ? ? ? { 190, ?38},
> + ? ? ? { 190, ?35},
> + ? ? ? { 189, ?33},
> + ? ? ? { 188, ?30},
> + ? ? ? { 187, ?28},
> + ? ? ? { 186, ?25},
> + ? ? ? { 185, ?23},
> + ? ? ? { 184, ?20},
> + ? ? ? { 183, ?18},
> + ? ? ? { 182, ?15},
> + ? ? ? { 181, ?13},
> + ? ? ? { 180, ?10},
> + ? ? ? { 179, ? 8},
> + ? ? ? { 178, ? 5},
> + ? ? ? { ? 0, ? 0},
> +};
> +
> +static const struct battery_thresh ?corgi_battery_levels_noac[] = {
> + ? ? ? { 213, 100},
> + ? ? ? { 212, ?98},
> + ? ? ? { 211, ?95},
> + ? ? ? { 210, ?93},
> + ? ? ? { 209, ?90},
> + ? ? ? { 208, ?88},
> + ? ? ? { 207, ?85},
> + ? ? ? { 206, ?83},
> + ? ? ? { 205, ?80},
> + ? ? ? { 204, ?78},
> + ? ? ? { 203, ?75},
> + ? ? ? { 202, ?73},
> + ? ? ? { 201, ?70},
> + ? ? ? { 200, ?68},
> + ? ? ? { 199, ?65},
> + ? ? ? { 198, ?63},
> + ? ? ? { 197, ?60},
> + ? ? ? { 196, ?58},
> + ? ? ? { 195, ?55},
> + ? ? ? { 194, ?53},
> + ? ? ? { 193, ?50},
> + ? ? ? { 192, ?48},
> + ? ? ? { 191, ?45},
> + ? ? ? { 190, ?43},
> + ? ? ? { 189, ?40},
> + ? ? ? { 188, ?38},
> + ? ? ? { 187, ?35},
> + ? ? ? { 186, ?33},
> + ? ? ? { 185, ?30},
> + ? ? ? { 184, ?28},
> + ? ? ? { 183, ?25},
> + ? ? ? { 182, ?23},
> + ? ? ? { 181, ?20},
> + ? ? ? { 180, ?18},
> + ? ? ? { 179, ?15},
> + ? ? ? { 178, ?13},
> + ? ? ? { 177, ?10},
> + ? ? ? { 176, ? 8},
> + ? ? ? { 175, ? 5},
> + ? ? ? { ? 0, ? 0},
> +};
> +
> ?static void corgi_charger_init(void)
> ?{
> ? ? ? ?pxa_gpio_mode(CORGI_GPIO_ADC_TEMP_ON | GPIO_OUT);
> @@ -214,8 +300,8 @@
> ? ? ? ?.fatal_acin_volt ?= SHARPSL_FATAL_ACIN_VOLT,
> ? ? ? ?.fatal_noacin_volt= SHARPSL_FATAL_NOACIN_VOLT,
> ? ? ? ?.bat_levels ? ? ? = 40,
> - ? ? ? .bat_levels_noac ?= spitz_battery_levels_noac,
> - ? ? ? .bat_levels_acin ?= spitz_battery_levels_acin,
> + ? ? ? .bat_levels_noac ?= corgi_battery_levels_noac,
> + ? ? ? .bat_levels_acin ?= corgi_battery_levels_acin,
> ? ? ? ?.status_high_acin = 188,
> ? ? ? ?.status_low_acin ?= 178,
> ? ? ? ?.status_high_noac = 185,
> diff -ur ./arch/arm.ofic/mach-pxa/sharpsl.h ./arch/arm/mach-pxa/sharpsl.h
> --- ./arch/arm.ofic/mach-pxa/sharpsl.h ?2009-09-10 00:13:59.000000000 +0200
> +++ ./arch/arm/mach-pxa/sharpsl.h ? ? ? 2009-10-14 12:12:13.000000000 +0200
> @@ -42,8 +42,23 @@
> ?#define MAX1111_BATT_TEMP ? 2u
> ?#define MAX1111_ACIN_VOLT ? 6u
>
> -extern struct battery_thresh spitz_battery_levels_acin[];
> -extern struct battery_thresh spitz_battery_levels_noac[];
> ?int sharpsl_pm_pxa_read_max1111(int channel);
>
>
> +/*
> + * Constants
> + */
> +#define SHARPSL_CHARGE_ON_TIME_INTERVAL ? ? ? ?(msecs_to_jiffies(1*60*1000)) ?/* 1 min */
> +#define SHARPSL_CHARGE_FINISH_TIME ? ? ? ? ? ? (msecs_to_jiffies(10*60*1000)) /* 10 min */
> +#define SHARPSL_BATCHK_TIME ? ? ? ? ? ? ? ? ? ?(msecs_to_jiffies(15*1000)) ? ?/* 15 sec */
> +#define SHARPSL_BATCHK_TIME_SUSPEND ? ? ? ? ? ?(60*10) ? ? ? ? ? ? ? ? ? ? ? ?/* 10 min */
> +
> +#define SHARPSL_WAIT_CO_TIME ? ? ? ? ? ? ? ? ? 15 ?/* 15 sec */
> +#define SHARPSL_WAIT_DISCHARGE_ON ? ? ? ? ? ? ?100 /* 100 msec */
> +#define SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP ? 10 ?/* 10 msec */
> +#define SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT ? 10 ?/* 10 msec */
> +#define SHARPSL_CHECK_BATTERY_WAIT_TIME_ACIN ? 10 ?/* 10 msec */
> +#define SHARPSL_CHARGE_WAIT_TIME ? ? ? ? ? ? ? 15 ?/* 15 msec */
> +#define SHARPSL_CHARGE_CO_CHECK_TIME ? ? ? ? ? 5 ? /* 5 msec */
> +#define SHARPSL_CHARGE_RETRY_CNT ? ? ? ? ? ? ? 1 ? /* eqv. 10 min */
> +
> Only in ./arch/arm/mach-pxa: sharpsl.h~
> diff -ur ./arch/arm.ofic/mach-pxa/sharpsl_pm.c ./arch/arm/mach-pxa/sharpsl_pm.c
> --- ./arch/arm.ofic/mach-pxa/sharpsl_pm.c ? ? ? 2009-10-06 13:48:07.000000000 +0200
> +++ ./arch/arm/mach-pxa/sharpsl_pm.c ? ?2009-10-14 12:12:05.000000000 +0200
> @@ -32,25 +32,10 @@
> ?#include <mach/regs-rtc.h>
> ?#include <mach/sharpsl.h>
> ?#include <mach/sharpsl_pm.h>
> +#include <mach/spitz.h>
>
> ?#include "sharpsl.h"
>
> -/*
> - * Constants
> - */
> -#define SHARPSL_CHARGE_ON_TIME_INTERVAL ? ? ? ?(msecs_to_jiffies(1*60*1000)) ?/* 1 min */
> -#define SHARPSL_CHARGE_FINISH_TIME ? ? ? ? ? ? (msecs_to_jiffies(10*60*1000)) /* 10 min */
> -#define SHARPSL_BATCHK_TIME ? ? ? ? ? ? ? ? ? ?(msecs_to_jiffies(15*1000)) ? ?/* 15 sec */
> -#define SHARPSL_BATCHK_TIME_SUSPEND ? ? ? ? ? ?(60*10) ? ? ? ? ? ? ? ? ? ? ? ?/* 10 min */
> -
> -#define SHARPSL_WAIT_CO_TIME ? ? ? ? ? ? ? ? ? 15 ?/* 15 sec */
> -#define SHARPSL_WAIT_DISCHARGE_ON ? ? ? ? ? ? ?100 /* 100 msec */
> -#define SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP ? 10 ?/* 10 msec */
> -#define SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT ? 10 ?/* 10 msec */
> -#define SHARPSL_CHECK_BATTERY_WAIT_TIME_ACIN ? 10 ?/* 10 msec */
> -#define SHARPSL_CHARGE_WAIT_TIME ? ? ? ? ? ? ? 15 ?/* 15 msec */
> -#define SHARPSL_CHARGE_CO_CHECK_TIME ? ? ? ? ? 5 ? /* 5 msec */
> -#define SHARPSL_CHARGE_RETRY_CNT ? ? ? ? ? ? ? 1 ? /* eqv. 10 min */
>
> ?/*
> ?* Prototypes
> @@ -72,112 +57,28 @@
> ?* Variables
> ?*/
> ?struct sharpsl_pm_status sharpsl_pm;
> +EXPORT_SYMBOL(sharpsl_pm);
> ?static DECLARE_DELAYED_WORK(toggle_charger, sharpsl_charge_toggle);
> ?static DECLARE_DELAYED_WORK(sharpsl_bat, sharpsl_battery_thread);
> ?DEFINE_LED_TRIGGER(sharpsl_charge_led_trigger);
>
>
>
> -struct battery_thresh spitz_battery_levels_acin[] = {
> - ? ? ? { 213, 100},
> - ? ? ? { 212, ?98},
> - ? ? ? { 211, ?95},
> - ? ? ? { 210, ?93},
> - ? ? ? { 209, ?90},
> - ? ? ? { 208, ?88},
> - ? ? ? { 207, ?85},
> - ? ? ? { 206, ?83},
> - ? ? ? { 205, ?80},
> - ? ? ? { 204, ?78},
> - ? ? ? { 203, ?75},
> - ? ? ? { 202, ?73},
> - ? ? ? { 201, ?70},
> - ? ? ? { 200, ?68},
> - ? ? ? { 199, ?65},
> - ? ? ? { 198, ?63},
> - ? ? ? { 197, ?60},
> - ? ? ? { 196, ?58},
> - ? ? ? { 195, ?55},
> - ? ? ? { 194, ?53},
> - ? ? ? { 193, ?50},
> - ? ? ? { 192, ?48},
> - ? ? ? { 192, ?45},
> - ? ? ? { 191, ?43},
> - ? ? ? { 191, ?40},
> - ? ? ? { 190, ?38},
> - ? ? ? { 190, ?35},
> - ? ? ? { 189, ?33},
> - ? ? ? { 188, ?30},
> - ? ? ? { 187, ?28},
> - ? ? ? { 186, ?25},
> - ? ? ? { 185, ?23},
> - ? ? ? { 184, ?20},
> - ? ? ? { 183, ?18},
> - ? ? ? { 182, ?15},
> - ? ? ? { 181, ?13},
> - ? ? ? { 180, ?10},
> - ? ? ? { 179, ? 8},
> - ? ? ? { 178, ? 5},
> - ? ? ? { ? 0, ? 0},
> -};
> -
> -struct battery_thresh ?spitz_battery_levels_noac[] = {
> - ? ? ? { 213, 100},
> - ? ? ? { 212, ?98},
> - ? ? ? { 211, ?95},
> - ? ? ? { 210, ?93},
> - ? ? ? { 209, ?90},
> - ? ? ? { 208, ?88},
> - ? ? ? { 207, ?85},
> - ? ? ? { 206, ?83},
> - ? ? ? { 205, ?80},
> - ? ? ? { 204, ?78},
> - ? ? ? { 203, ?75},
> - ? ? ? { 202, ?73},
> - ? ? ? { 201, ?70},
> - ? ? ? { 200, ?68},
> - ? ? ? { 199, ?65},
> - ? ? ? { 198, ?63},
> - ? ? ? { 197, ?60},
> - ? ? ? { 196, ?58},
> - ? ? ? { 195, ?55},
> - ? ? ? { 194, ?53},
> - ? ? ? { 193, ?50},
> - ? ? ? { 192, ?48},
> - ? ? ? { 191, ?45},
> - ? ? ? { 190, ?43},
> - ? ? ? { 189, ?40},
> - ? ? ? { 188, ?38},
> - ? ? ? { 187, ?35},
> - ? ? ? { 186, ?33},
> - ? ? ? { 185, ?30},
> - ? ? ? { 184, ?28},
> - ? ? ? { 183, ?25},
> - ? ? ? { 182, ?23},
> - ? ? ? { 181, ?20},
> - ? ? ? { 180, ?18},
> - ? ? ? { 179, ?15},
> - ? ? ? { 178, ?13},
> - ? ? ? { 177, ?10},
> - ? ? ? { 176, ? 8},
> - ? ? ? { 175, ? 5},
> - ? ? ? { ? 0, ? 0},
> -};
> -
> ?/* MAX1111 Commands */
> -#define MAXCTRL_PD0 ? ? ?1u << 0
> -#define MAXCTRL_PD1 ? ? ?1u << 1
> -#define MAXCTRL_SGL ? ? ?1u << 2
> -#define MAXCTRL_UNI ? ? ?1u << 3
> +#define MAXCTRL_PD0 ? ? ?(1u << 0)
> +#define MAXCTRL_PD1 ? ? ?(1u << 1)
> +#define MAXCTRL_SGL ? ? ?(1u << 2)
> +#define MAXCTRL_UNI ? ? ?(1u << 3)
> ?#define MAXCTRL_SEL_SH ? 4
> -#define MAXCTRL_STR ? ? ?1u << 7
> +#define MAXCTRL_STR ? ? ?(1u << 7)
>
> ?/*
> ?* Read MAX1111 ADC
> ?*/
> ?int sharpsl_pm_pxa_read_max1111(int channel)
> ?{
> - ? ? ? if (machine_is_tosa()) // Ugly, better move this function into another module
> + ? ? ? /* Ugly, better move this function into another module */
> + ? ? ? if (machine_is_tosa())
> ? ? ? ? ? ?return 0;
>
> ?#ifdef CONFIG_CORGI_SSP_DEPRECATED
> @@ -193,7 +94,7 @@
> ?#endif
> ?}
>
> -static int get_percentage(int voltage)
> +int get_percentage(int voltage)
> ?{
> ? ? ? ?int i = sharpsl_pm.machinfo->bat_levels - 1;
> ? ? ? ?int bl_status = sharpsl_pm.machinfo->backlight_get_status ? sharpsl_pm.machinfo->backlight_get_status() : 0;
> @@ -209,6 +110,7 @@
>
> ? ? ? ?return thresh[i].percentage;
> ?}
> +EXPORT_SYMBOL(get_percentage);
>
> ?static int get_apm_status(int voltage)
> ?{
> @@ -238,7 +140,7 @@
>
> ?static void sharpsl_battery_thread(struct work_struct *private_)
> ?{
> - ? ? ? int voltage, percent, apm_status, i = 0;
> + ? ? ? int voltage, percent, apm_status, i;
>
> ? ? ? ?if (!sharpsl_pm.machinfo)
> ? ? ? ? ? ? ? ?return;
> @@ -250,15 +152,14 @@
> ? ? ? ? ? ? ? ? ? ? ? ?&& time_after(jiffies, sharpsl_pm.charge_start_time + ?SHARPSL_CHARGE_ON_TIME_INTERVAL))
> ? ? ? ? ? ? ? ?schedule_delayed_work(&toggle_charger, 0);
>
> - ? ? ? while(1) {
> + ? ? ? for (i = 0; i < 5; i++) {
> ? ? ? ? ? ? ? ?voltage = sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_VOLT);
> -
> - ? ? ? ? ? ? ? if (voltage > 0) break;
> - ? ? ? ? ? ? ? if (i++ > 5) {
> - ? ? ? ? ? ? ? ? ? ? ? voltage = sharpsl_pm.machinfo->bat_levels_noac[0].voltage;
> - ? ? ? ? ? ? ? ? ? ? ? dev_warn(sharpsl_pm.dev, "Warning: Cannot read main battery!\n");
> + ? ? ? ? ? ? ? if (voltage > 0)
> ? ? ? ? ? ? ? ? ? ? ? ?break;
> - ? ? ? ? ? ? ? }
> + ? ? ? }
> + ? ? ? if (voltage <= 0) {
> + ? ? ? ? ? ? ? voltage = sharpsl_pm.machinfo->bat_levels_noac[0].voltage;
> + ? ? ? ? ? ? ? dev_warn(sharpsl_pm.dev, "Warning: Cannot read main battery!\n");
> ? ? ? ?}
>
> ? ? ? ?voltage = sharpsl_average_value(voltage);
> @@ -266,8 +167,10 @@
> ? ? ? ?percent = get_percentage(voltage);
>
> ? ? ? ?/* At low battery voltages, the voltage has a tendency to start
> - ? ? ? ? ? creeping back up so we try to avoid this here */
> - ? ? ? if ((sharpsl_pm.battstat.ac_status == APM_AC_ONLINE) || (apm_status == APM_BATTERY_STATUS_HIGH) || ?percent <= sharpsl_pm.battstat.mainbat_percent) {
> + ? ? ? ? ?creeping back up so we try to avoid this here */
> + ? ? ? if ((sharpsl_pm.battstat.ac_status == APM_AC_ONLINE)
> + ? ? ? ? ? || (apm_status == APM_BATTERY_STATUS_HIGH)
> + ? ? ? ? ? || percent <= sharpsl_pm.battstat.mainbat_percent) {
> ? ? ? ? ? ? ? ?sharpsl_pm.battstat.mainbat_voltage = voltage;
> ? ? ? ? ? ? ? ?sharpsl_pm.battstat.mainbat_status = apm_status;
> ? ? ? ? ? ? ? ?sharpsl_pm.battstat.mainbat_percent = percent;
> @@ -279,8 +182,8 @@
> ?#ifdef CONFIG_BACKLIGHT_CORGI
> ? ? ? ?/* If battery is low. limit backlight intensity to save power. */
> ? ? ? ?if ((sharpsl_pm.battstat.ac_status != APM_AC_ONLINE)
> - ? ? ? ? ? ? ? ? ? ? ? && ((sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_LOW) ||
> - ? ? ? ? ? ? ? ? ? ? ? (sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_CRITICAL))) {
> + ? ? ? ? ? && ((sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_LOW)
> + ? ? ? ? ? || (sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_CRITICAL))) {
> ? ? ? ? ? ? ? ?if (!(sharpsl_pm.flags & SHARPSL_BL_LIMIT)) {
> ? ? ? ? ? ? ? ? ? ? ? ?sharpsl_pm.machinfo->backlight_limit(1);
> ? ? ? ? ? ? ? ? ? ? ? ?sharpsl_pm.flags |= SHARPSL_BL_LIMIT;
> @@ -293,8 +196,8 @@
>
> ? ? ? ?/* Suspend if critical battery level */
> ? ? ? ?if ((sharpsl_pm.battstat.ac_status != APM_AC_ONLINE)
> - ? ? ? ? ? ? ? ? ? ? ? && (sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_CRITICAL)
> - ? ? ? ? ? ? ? ? ? ? ? && !(sharpsl_pm.flags & SHARPSL_APM_QUEUED)) {
> + ? ? ? ? ? ?&& (sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_CRITICAL)
> + ? ? ? ? ? ?&& !(sharpsl_pm.flags & SHARPSL_APM_QUEUED)) {
> ? ? ? ? ? ? ? ?sharpsl_pm.flags |= SHARPSL_APM_QUEUED;
> ? ? ? ? ? ? ? ?dev_err(sharpsl_pm.dev, "Fatal Off\n");
> ? ? ? ? ? ? ? ?apm_queue_event(APM_CRITICAL_SUSPEND);
> @@ -339,6 +242,8 @@
>
> ?static void sharpsl_charge_error(void)
> ?{
> + ? ? ? dev_warn(sharpsl_pm.dev, "Charger Error\n");
> +
> ? ? ? ?sharpsl_pm_led(SHARPSL_LED_ERROR);
> ? ? ? ?sharpsl_pm.machinfo->charge(0);
> ? ? ? ?sharpsl_pm.charge_mode = CHRG_ERROR;
> @@ -346,7 +251,7 @@
>
> ?static void sharpsl_charge_toggle(struct work_struct *private_)
> ?{
> - ? ? ? dev_dbg(sharpsl_pm.dev, "Toogling Charger at time: %lx\n", jiffies);
> + ? ? ? dev_dbg(sharpsl_pm.dev, "Toggling Charger at time: %lx\n", jiffies);
>
> ? ? ? ?if (!sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN)) {
> ? ? ? ? ? ? ? ?sharpsl_charge_off();
> @@ -368,7 +273,7 @@
> ?{
> ? ? ? ?int acin = sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN);
>
> - ? ? ? dev_dbg(sharpsl_pm.dev, "AC Status: %d\n",acin);
> + ? ? ? dev_dbg(sharpsl_pm.dev, "AC Status: %d\n", acin);
>
> ? ? ? ?sharpsl_average_clear();
> ? ? ? ?if (acin && (sharpsl_pm.charge_mode != CHRG_ON))
> @@ -472,14 +377,14 @@
> ? ? ? ?sharpsl_ad[sharpsl_ad_index] = ad;
> ? ? ? ?sharpsl_ad_index++;
> ? ? ? ?if (sharpsl_ad_index >= SHARPSL_CNV_VALUE_NUM) {
> - ? ? ? ? ? ? ? for (i=0; i < (SHARPSL_CNV_VALUE_NUM-1); i++)
> + ? ? ? ? ? ? ? for (i = 0; i < (SHARPSL_CNV_VALUE_NUM-1); i++)
> ? ? ? ? ? ? ? ? ? ? ? ?sharpsl_ad[i] = sharpsl_ad[i+1];
> ? ? ? ? ? ? ? ?sharpsl_ad_index = SHARPSL_CNV_VALUE_NUM - 1;
> ? ? ? ?}
> - ? ? ? for (i=0; i < sharpsl_ad_index; i++)
> + ? ? ? for (i = 0; i < sharpsl_ad_index; i++)
> ? ? ? ? ? ? ? ?ad_val += sharpsl_ad[i];
>
> - ? ? ? return (ad_val / sharpsl_ad_index);
> + ? ? ? return ad_val / sharpsl_ad_index;
> ?}
>
> ?/*
> @@ -492,8 +397,8 @@
>
> ? ? ? ?/* Find MAX val */
> ? ? ? ?temp = val[0];
> - ? ? ? j=0;
> - ? ? ? for (i=1; i<5; i++) {
> + ? ? ? j = 0;
> + ? ? ? for (i = 1; i < 5; i++) {
> ? ? ? ? ? ? ? ?if (temp < val[i]) {
> ? ? ? ? ? ? ? ? ? ? ? ?temp = val[i];
> ? ? ? ? ? ? ? ? ? ? ? ?j = i;
> @@ -502,21 +407,21 @@
>
> ? ? ? ?/* Find MIN val */
> ? ? ? ?temp = val[4];
> - ? ? ? k=4;
> - ? ? ? for (i=3; i>=0; i--) {
> + ? ? ? k = 4;
> + ? ? ? for (i = 3; i >= 0; i--) {
> ? ? ? ? ? ? ? ?if (temp > val[i]) {
> ? ? ? ? ? ? ? ? ? ? ? ?temp = val[i];
> ? ? ? ? ? ? ? ? ? ? ? ?k = i;
> ? ? ? ? ? ? ? ?}
> ? ? ? ?}
>
> - ? ? ? for (i=0; i<5; i++)
> - ? ? ? ? ? ? ? if (i != j && i != k )
> + ? ? ? for (i = 0; i < 5; i++)
> + ? ? ? ? ? ? ? if (i != j && i != k)
> ? ? ? ? ? ? ? ? ? ? ? ?sum += val[i];
>
> ? ? ? ?dev_dbg(sharpsl_pm.dev, "Average: %d from values: %d, %d, %d, %d, %d\n", sum/3, val[0], val[1], val[2], val[3], val[4]);
>
> - ? ? ? return (sum/3);
> + ? ? ? return sum/3;
> ?}
>
> ?static int sharpsl_check_battery_temp(void)
> @@ -524,7 +429,7 @@
> ? ? ? ?int val, i, buff[5];
>
> ? ? ? ?/* Check battery temperature */
> - ? ? ? for (i=0; i<5; i++) {
> + ? ? ? for (i = 0; i < 5; i++) {
> ? ? ? ? ? ? ? ?mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
> ? ? ? ? ? ? ? ?sharpsl_pm.machinfo->measure_temp(1);
> ? ? ? ? ? ? ? ?mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
> @@ -535,8 +440,10 @@
> ? ? ? ?val = get_select_val(buff);
>
> ? ? ? ?dev_dbg(sharpsl_pm.dev, "Temperature: %d\n", val);
> - ? ? ? if (val > sharpsl_pm.machinfo->charge_on_temp) {
> - ? ? ? ? ? ? ? printk(KERN_WARNING "Not charging: temperature out of limits.\n");
> + ? ? ? /* FIXME: this should catch battery read errors, but we should
> + ? ? ? ? ?probably avoid charging in <0C temperatures, too. */
> + ? ? ? if ((val < 0) || (val > sharpsl_pm.machinfo->charge_on_temp)) {
> + ? ? ? ? ? ? ? dev_warn(sharpsl_pm.dev, "Not charging: temperature %d out of limits.\n", val);
> ? ? ? ? ? ? ? ?return -1;
> ? ? ? ?}
>
> @@ -557,7 +464,7 @@
> ? ? ? ? ? ? ? ?sharpsl_pm.machinfo->discharge1(1);
>
> ? ? ? ?/* Check battery voltage */
> - ? ? ? for (i=0; i<5; i++) {
> + ? ? ? for (i = 0; i < 5; i++) {
> ? ? ? ? ? ? ? ?buff[i] = sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_VOLT);
> ? ? ? ? ? ? ? ?mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT);
> ? ? ? ?}
> @@ -581,16 +488,16 @@
> ?{
> ? ? ? ?int temp, i, buff[5];
>
> - ? ? ? for (i=0; i<5; i++) {
> + ? ? ? for (i = 0; i < 5; i++) {
> ? ? ? ? ? ? ? ?buff[i] = sharpsl_pm.machinfo->read_devdata(SHARPSL_ACIN_VOLT);
> ? ? ? ? ? ? ? ?mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_ACIN);
> ? ? ? ?}
>
> ? ? ? ?temp = get_select_val(buff);
> - ? ? ? dev_dbg(sharpsl_pm.dev, "AC Voltage: %d\n",temp);
> + ? ? ? dev_dbg(sharpsl_pm.dev, "AC Voltage: %d\n", temp);
>
> ? ? ? ?if ((temp > sharpsl_pm.machinfo->charge_acin_high) || (temp < sharpsl_pm.machinfo->charge_acin_low)) {
> - ? ? ? ? ? ? ? dev_err(sharpsl_pm.dev, "Error: AC check failed.\n");
> + ? ? ? ? ? ? ? dev_err(sharpsl_pm.dev, "Error: AC check failed: voltage %d.\n", temp);
> ? ? ? ? ? ? ? ?return -1;
> ? ? ? ?}
>
> @@ -624,9 +531,9 @@
>
> ?static void corgi_goto_sleep(unsigned long alarm_time, unsigned int alarm_enable, suspend_state_t state)
> ?{
> - ? ? ? dev_dbg(sharpsl_pm.dev, "Time is: %08x\n",RCNR);
> + ? ? ? dev_dbg(sharpsl_pm.dev, "Time is: %08x\n", RCNR);
>
> - ? ? ? dev_dbg(sharpsl_pm.dev, "Offline Charge Activate = %d\n",sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG);
> + ? ? ? dev_dbg(sharpsl_pm.dev, "Offline Charge Activate = %d\n", sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG);
> ? ? ? ?/* not charging and AC-IN! */
>
> ? ? ? ?if ((sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG) && (sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN))) {
> @@ -644,12 +551,12 @@
> ? ? ? ?if ((sharpsl_pm.charge_mode == CHRG_ON) && ((alarm_enable && ((alarm_time - RCNR) > (SHARPSL_BATCHK_TIME_SUSPEND + 30))) || !alarm_enable)) {
> ? ? ? ? ? ? ? ?RTSR &= RTSR_ALE;
> ? ? ? ? ? ? ? ?RTAR = RCNR + SHARPSL_BATCHK_TIME_SUSPEND;
> - ? ? ? ? ? ? ? dev_dbg(sharpsl_pm.dev, "Charging alarm at: %08x\n",RTAR);
> + ? ? ? ? ? ? ? dev_dbg(sharpsl_pm.dev, "Charging alarm at: %08x\n", RTAR);
> ? ? ? ? ? ? ? ?sharpsl_pm.flags |= SHARPSL_ALARM_ACTIVE;
> ? ? ? ?} else if (alarm_enable) {
> ? ? ? ? ? ? ? ?RTSR &= RTSR_ALE;
> ? ? ? ? ? ? ? ?RTAR = alarm_time;
> - ? ? ? ? ? ? ? dev_dbg(sharpsl_pm.dev, "User alarm at: %08x\n",RTAR);
> + ? ? ? ? ? ? ? dev_dbg(sharpsl_pm.dev, "User alarm at: %08x\n", RTAR);
> ? ? ? ?} else {
> ? ? ? ? ? ? ? ?dev_dbg(sharpsl_pm.dev, "No alarms set.\n");
> ? ? ? ?}
> @@ -658,19 +565,20 @@
>
> ? ? ? ?sharpsl_pm.machinfo->postsuspend();
>
> - ? ? ? dev_dbg(sharpsl_pm.dev, "Corgi woken up from suspend: %08x\n",PEDR);
> +
> + ? ? ? dev_dbg(sharpsl_pm.dev, "Corgi woken up from suspend: %08x\n", PEDR);
> ?}
>
> ?static int corgi_enter_suspend(unsigned long alarm_time, unsigned int alarm_enable, suspend_state_t state)
> ?{
> - ? ? ? if (!sharpsl_pm.machinfo->should_wakeup(!(sharpsl_pm.flags & SHARPSL_ALARM_ACTIVE) && alarm_enable) )
> - ? ? ? {
> + ?return 0;
> + ? ? ? if (!sharpsl_pm.machinfo->should_wakeup(!(sharpsl_pm.flags & SHARPSL_ALARM_ACTIVE) && alarm_enable)) {
> ? ? ? ? ? ? ? ?if (!(sharpsl_pm.flags & SHARPSL_ALARM_ACTIVE)) {
> ? ? ? ? ? ? ? ? ? ? ? ?dev_dbg(sharpsl_pm.dev, "No user triggered wakeup events and not charging. Strange. Suspend.\n");
> ? ? ? ? ? ? ? ? ? ? ? ?corgi_goto_sleep(alarm_time, alarm_enable, state);
> ? ? ? ? ? ? ? ? ? ? ? ?return 1;
> ? ? ? ? ? ? ? ?}
> - ? ? ? ? ? ? ? if(sharpsl_off_charge_battery()) {
> + ? ? ? ? ? ? ? if (sharpsl_off_charge_battery()) {
> ? ? ? ? ? ? ? ? ? ? ? ?dev_dbg(sharpsl_pm.dev, "Charging. Suspend...\n");
> ? ? ? ? ? ? ? ? ? ? ? ?corgi_goto_sleep(alarm_time, alarm_enable, state);
> ? ? ? ? ? ? ? ? ? ? ? ?return 1;
> @@ -697,7 +605,7 @@
>
> ? ? ? ?corgi_goto_sleep(alarm_time, alarm_status, state);
>
> - ? ? ? while (corgi_enter_suspend(alarm_time,alarm_status,state))
> + ? ? ? while (corgi_enter_suspend(alarm_time, alarm_status, state))
> ? ? ? ? ? ? ? ?{}
>
> ? ? ? ?if (sharpsl_pm.machinfo->earlyresume)
> @@ -732,7 +640,7 @@
> ? ? ? ? ? ? ? ?sharpsl_pm.machinfo->discharge1(1);
>
> ? ? ? ?/* Check battery : check inserting battery ? */
> - ? ? ? for (i=0; i<5; i++) {
> + ? ? ? for (i = 0; i < 5; i++) {
> ? ? ? ? ? ? ? ?buff[i] = sharpsl_pm.machinfo->read_devdata(SHARPSL_BATT_VOLT);
> ? ? ? ? ? ? ? ?mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT);
> ? ? ? ?}
> @@ -812,7 +720,7 @@
> ? ? ? ? ? ? ? ?mdelay(SHARPSL_CHARGE_CO_CHECK_TIME);
>
> ? ? ? ? ? ? ? ?time = RCNR;
> - ? ? ? ? ? ? ? while(1) {
> + ? ? ? ? ? ? ? while (1) {
> ? ? ? ? ? ? ? ? ? ? ? ?/* Check if any wakeup event had occurred */
> ? ? ? ? ? ? ? ? ? ? ? ?if (sharpsl_pm.machinfo->charger_wakeup() != 0)
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?return 0;
> @@ -835,9 +743,9 @@
> ? ? ? ?mdelay(SHARPSL_CHARGE_CO_CHECK_TIME);
>
> ? ? ? ?time = RCNR;
> - ? ? ? while(1) {
> + ? ? ? while (1) {
> ? ? ? ? ? ? ? ?/* Check if any wakeup event had occurred */
> - ? ? ? ? ? ? ? if (sharpsl_pm.machinfo->charger_wakeup() != 0)
> + ? ? ? ? ? ? ? if (sharpsl_pm.machinfo->charger_wakeup())
> ? ? ? ? ? ? ? ? ? ? ? ?return 0;
> ? ? ? ? ? ? ? ?/* Check for timeout */
> ? ? ? ? ? ? ? ?if ((RCNR-time) > SHARPSL_WAIT_CO_TIME) {
> @@ -864,12 +772,12 @@
>
> ?static ssize_t battery_percentage_show(struct device *dev, struct device_attribute *attr, char *buf)
> ?{
> - ? ? ? return sprintf(buf, "%d\n",sharpsl_pm.battstat.mainbat_percent);
> + ? ? ? return sprintf(buf, "%d\n", sharpsl_pm.battstat.mainbat_percent);
> ?}
>
> ?static ssize_t battery_voltage_show(struct device *dev, struct device_attribute *attr, char *buf)
> ?{
> - ? ? ? return sprintf(buf, "%d\n",sharpsl_pm.battstat.mainbat_voltage);
> + ? ? ? return sprintf(buf, "%d\n", sharpsl_pm.battstat.mainbat_voltage);
> ?}
>
> ?static DEVICE_ATTR(battery_percentage, 0444, battery_percentage_show, NULL);
> @@ -943,7 +851,6 @@
> ? ? ? ? ? ? ? ?}
> ? ? ? ?}
>
> - ? ? ? if (sharpsl_pm.machinfo->batfull_irq)
> - ? ? ? {
> + ? ? ? if (sharpsl_pm.machinfo->batfull_irq) {
> ? ? ? ? ? ? ? ?/* Register interrupt handler. */
> ? ? ? ? ? ? ? ?if (request_irq(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batfull), sharpsl_chrg_full_isr, IRQF_DISABLED | IRQF_TRIGGER_RISING, "CO", sharpsl_chrg_full_isr)) {
> diff -ur ./arch/arm.ofic/mach-pxa/spitz.c ./arch/arm/mach-pxa/spitz.c
> --- ./arch/arm.ofic/mach-pxa/spitz.c ? ?2009-10-06 13:48:07.000000000 +0200
> +++ ./arch/arm/mach-pxa/spitz.c 2009-10-14 11:01:36.000000000 +0200
> @@ -686,12 +733,19 @@
> ? ? ? ?.dev.platform_data = &sharpsl_rom_data,
> ?};
>
> +static struct platform_device spitz_battery_device = {
> + ? ? ? .name ? = "spitz-battery",
> + ? ? ? .id ? ? = -1,
> +};
> +
> +
> ?static struct platform_device *devices[] __initdata = {
> ? ? ? ?&spitzscoop_device,
> ? ? ? ?&spitzkbd_device,
> ? ? ? ?&spitzled_device,
> ? ? ? ?&sharpsl_nand_device,
> ? ? ? ?&sharpsl_rom_device,
> + ? ? ? &spitz_battery_device,
> ?};
>
> ?static void spitz_poweroff(void)
> --- ./arch/arm.ofic/mach-pxa/spitz_pm.c 2009-09-10 00:13:59.000000000 +0200
> +++ ./arch/arm/mach-pxa/spitz_pm.c ? ? ?2009-10-19 07:28:42.000000000 +0200
> @@ -37,6 +37,93 @@
>
> ?static int spitz_last_ac_status;
>
> +static const struct battery_thresh spitz_battery_levels_acin[] = {
> + ? ? ? { 213, 100},
> + ? ? ? { 212, ?98},
> + ? ? ? { 211, ?95},
> + ? ? ? { 210, ?93},
> + ? ? ? { 209, ?90},
> + ? ? ? { 208, ?88},
> + ? ? ? { 207, ?85},
> + ? ? ? { 206, ?83},
> + ? ? ? { 205, ?80},
> + ? ? ? { 204, ?78},
> + ? ? ? { 203, ?75},
> + ? ? ? { 202, ?73},
> + ? ? ? { 201, ?70},
> + ? ? ? { 200, ?68},
> + ? ? ? { 199, ?65},
> + ? ? ? { 198, ?63},
> + ? ? ? { 197, ?60},
> + ? ? ? { 196, ?58},
> + ? ? ? { 195, ?55},
> + ? ? ? { 194, ?53},
> + ? ? ? { 193, ?50},
> + ? ? ? { 192, ?48},
> + ? ? ? { 192, ?45},
> + ? ? ? { 191, ?43},
> + ? ? ? { 191, ?40},
> + ? ? ? { 190, ?38},
> + ? ? ? { 190, ?35},
> + ? ? ? { 189, ?33},
> + ? ? ? { 188, ?30},
> + ? ? ? { 187, ?28},
> + ? ? ? { 186, ?25},
> + ? ? ? { 185, ?23},
> + ? ? ? { 184, ?20},
> + ? ? ? { 183, ?18},
> + ? ? ? { 182, ?15},
> + ? ? ? { 181, ?13},
> + ? ? ? { 180, ?10},
> + ? ? ? { 179, ? 8},
> + ? ? ? { 178, ? 5},
> + ? ? ? { ? 0, ? 0},
> +};
> +
> +static const struct battery_thresh ?spitz_battery_levels_noac[] = {
> + ? ? ? { 213, 100},
> + ? ? ? { 212, ?98},
> + ? ? ? { 211, ?95},
> + ? ? ? { 210, ?93},
> + ? ? ? { 209, ?90},
> + ? ? ? { 208, ?88},
> + ? ? ? { 207, ?85},
> + ? ? ? { 206, ?83},
> + ? ? ? { 205, ?80},
> + ? ? ? { 204, ?78},
> + ? ? ? { 203, ?75},
> + ? ? ? { 202, ?73},
> + ? ? ? { 201, ?70},
> + ? ? ? { 200, ?68},
> + ? ? ? { 199, ?65},
> + ? ? ? { 198, ?63},
> + ? ? ? { 197, ?60},
> + ? ? ? { 196, ?58},
> + ? ? ? { 195, ?55},
> + ? ? ? { 194, ?53},
> + ? ? ? { 193, ?50},
> + ? ? ? { 192, ?48},
> + ? ? ? { 191, ?45},
> + ? ? ? { 190, ?43},
> + ? ? ? { 189, ?40},
> + ? ? ? { 188, ?38},
> + ? ? ? { 187, ?35},
> + ? ? ? { 186, ?33},
> + ? ? ? { 185, ?30},
> + ? ? ? { 184, ?28},
> + ? ? ? { 183, ?25},
> + ? ? ? { 182, ?23},
> + ? ? ? { 181, ?20},
> + ? ? ? { 180, ?18},
> + ? ? ? { 179, ?15},
> + ? ? ? { 178, ?13},
> + ? ? ? { 177, ?10},
> + ? ? ? { 176, ? 8},
> + ? ? ? { 175, ? 5},
> + ? ? ? { ? 0, ? 0},
> +};
> +
> +
> ?static void spitz_charger_init(void)
> ?{
> ? ? ? ?pxa_gpio_mode(SPITZ_GPIO_KEY_INT | GPIO_IN);
> @@ -103,7 +190,7 @@
> ? ? ? ?PFER = GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET);
> ? ? ? ?PWER = GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET) | PWER_RTC;
> ? ? ? ?PKWR = GPIO_bit(SPITZ_GPIO_SYNC) | GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET);
> - ? ? ? PKSR = 0xffffffff; // clear
> + ? ? ? PKSR = 0xffffffff; /* clear */
>
> ? ? ? ?/* nRESET_OUT Disable */
> ? ? ? ?PSLR |= PSLR_SL_ROD;
> @@ -149,7 +236,7 @@
> ? ? ? ?if (resume_on_alarm && (PEDR & PWER_RTC))
> ? ? ? ? ? ? ? ?is_resume |= PWER_RTC;
>
> - ? ? ? dev_dbg(sharpsl_pm.dev, "is_resume: %x\n",is_resume);
> + ? ? ? dev_dbg(sharpsl_pm.dev, "is_resume: %x\n", is_resume);
> ? ? ? ?return is_resume;
> ?}
>
> @@ -160,15 +247,15 @@
>
> ?unsigned long spitzpm_read_devdata(int type)
> ?{
> - ? ? ? switch(type) {
> + ? ? ? switch (type) {
> ? ? ? ?case SHARPSL_STATUS_ACIN:
> ? ? ? ? ? ? ? ?return (((~GPLR(SPITZ_GPIO_AC_IN)) & GPIO_bit(SPITZ_GPIO_AC_IN)) != 0);
> ? ? ? ?case SHARPSL_STATUS_LOCK:
> - ? ? ? ? ? ? ? return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batlock);
> + ? ? ? ? ? ? ? return !!READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batlock);
> ? ? ? ?case SHARPSL_STATUS_CHRGFULL:
> - ? ? ? ? ? ? ? return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batfull);
> + ? ? ? ? ? ? ? return !!READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batfull);
> ? ? ? ?case SHARPSL_STATUS_FATAL:
> - ? ? ? ? ? ? ? return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_fatal);
> + ? ? ? ? ? ? ? return !!READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_fatal);
> ? ? ? ?case SHARPSL_ACIN_VOLT:
> ? ? ? ? ? ? ? ?return sharpsl_pm_pxa_read_max1111(MAX1111_ACIN_VOLT);
> ? ? ? ?case SHARPSL_BATT_TEMP:
> @@ -179,6 +266,11 @@
> ? ? ? ?}
> ?}
>
> +int backlight_get_status(void)
> +{
> + ? ? ? return 0;
> +}
> +
> ?struct sharpsl_charger_machinfo spitz_pm_machinfo = {
> ? ? ? ?.init ? ? ? ? ? ? = spitz_charger_init,
> ? ? ? ?.exit ? ? ? ? ? ? = NULL,
> @@ -199,8 +291,9 @@
> ?#if defined(CONFIG_LCD_CORGI)
> ? ? ? ?.backlight_limit = corgi_lcd_limit_intensity,
> ?#elif defined(CONFIG_BACKLIGHT_CORGI)
> - ? ? ? ?.backlight_limit ?= corgibl_limit_intensity,
> + ? ? ? .backlight_limit ?= corgibl_limit_intensity,
> ?#endif
> +// ? ? .backlight_get_status = backlight_get_status,
> ? ? ? ?.charge_on_volt ? = SHARPSL_CHARGE_ON_VOLT,
> ? ? ? ?.charge_on_temp ? = SHARPSL_CHARGE_ON_TEMP,
> ? ? ? ?.charge_acin_high = SHARPSL_CHARGE_ON_ACIN_HIGH,
> @@ -241,7 +334,7 @@
>
> ?static void spitzpm_exit(void)
> ?{
> - ? ? ? platform_device_unregister(spitzpm_device);
> + ? ? ? platform_device_unregister(spitzpm_device);
> ?}
>
> ?module_init(spitzpm_init);
>
>
> --
> (english) http://www.livejournal.com/~pavelmachek
> (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* spitz battery driver
2009-11-10 3:48 ` Eric Miao
@ 2009-11-10 10:46 ` Pavel Machek
2009-11-10 12:34 ` Stanislav Brabec
0 siblings, 1 reply; 5+ messages in thread
From: Pavel Machek @ 2009-11-10 10:46 UTC (permalink / raw)
To: linux-arm-kernel
On Tue 2009-11-10 11:48:16, Eric Miao wrote:
> On Mon, Nov 9, 2009 at 9:58 PM, Pavel Machek <pavel@ucw.cz> wrote:
> > Hi!
> >
> > This introduces battery driver for spitz. For now it is
> > monitoring&debug-only.
> >
>
> This is a good move. However, I assume the patch is still RFC now.
> Or basically the coding style cleanup can be separated into another
> patch?
Its rfc now. Parts of codingstyle cleanup should already be in your
tree, I'll rediff it later.
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
^ permalink raw reply [flat|nested] 5+ messages in thread
* spitz battery driver
2009-11-10 10:46 ` Pavel Machek
@ 2009-11-10 12:34 ` Stanislav Brabec
2009-11-10 13:25 ` Pavel Machek
0 siblings, 1 reply; 5+ messages in thread
From: Stanislav Brabec @ 2009-11-10 12:34 UTC (permalink / raw)
To: linux-arm-kernel
Pavel Machek wrote:
> On Tue 2009-11-10 11:48:16, Eric Miao wrote:
> > > This introduces battery driver for spitz. For now it is
> > > monitoring&debug-only.
> > >
> >
> > This is a good move. However, I assume the patch is still RFC now.
> > Or basically the coding style cleanup can be separated into another
> > patch?
>
> Its rfc now. Parts of codingstyle cleanup should already be in your
> tree, I'll rediff it later.
Pavel, could you compare your patch with the "power: implement platform
battery driver"? patches from Paul Fertser just sent to LKML and
zaurus-devel list? Would it be complicated to migrate to it? I guess
that use of platform driver could allow to recycle major parts of the
charging driver by more devices.
________________________________________________________________________
Stanislav Brabec
http://www.penguin.cz/~utx/zaurus
^ permalink raw reply [flat|nested] 5+ messages in thread
* spitz battery driver
2009-11-10 12:34 ` Stanislav Brabec
@ 2009-11-10 13:25 ` Pavel Machek
0 siblings, 0 replies; 5+ messages in thread
From: Pavel Machek @ 2009-11-10 13:25 UTC (permalink / raw)
To: linux-arm-kernel
k
> > > This is a good move. However, I assume the patch is still RFC now.
> > > Or basically the coding style cleanup can be separated into another
> > > patch?
> >
> > Its rfc now. Parts of codingstyle cleanup should already be in your
> > tree, I'll rediff it later.
>
> Pavel, could you compare your patch with the "power: implement platform
> battery driver"??? patches from Paul Fertser just sent to LKML and
> zaurus-devel list? Would it be complicated to migrate to it? I guess
Complicated? No. Useful? Probably also no. Remove 50 lines for
additional indirection? I'd prefer not to.
> that use of platform driver could allow to recycle major parts of the
> charging driver by more devices.
take a look at those patches. I'd rather use mainline battery api.
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2009-11-10 13:25 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-11-09 13:58 spitz battery driver Pavel Machek
2009-11-10 3:48 ` Eric Miao
2009-11-10 10:46 ` Pavel Machek
2009-11-10 12:34 ` Stanislav Brabec
2009-11-10 13:25 ` Pavel Machek
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).