linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: daniel@caiaq.de (Daniel Mack)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 03/17] ARM: pxa/raumfeld: add SMSC9220 ethernet support
Date: Wed, 25 Nov 2009 11:42:17 +0100	[thread overview]
Message-ID: <1259145751-3331-4-git-send-email-daniel@caiaq.de> (raw)
In-Reply-To: <1259145751-3331-1-git-send-email-daniel@caiaq.de>

The 'Connector' and 'Speaker S/M' devices have an SMSC9220 ethernet chip
onboard.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
---
 arch/arm/mach-pxa/raumfeld.c |   51 ++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 51 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c
index 075e337..82af0dc 100644
--- a/arch/arm/mach-pxa/raumfeld.c
+++ b/arch/arm/mach-pxa/raumfeld.c
@@ -19,7 +19,10 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/sysdev.h>
+#include <linux/platform_device.h>
 #include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/smsc911x.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -92,6 +95,52 @@ static mfp_cfg_t raumfeld_pin_config[] __initdata = {
 	GPIO110_UART3_RXD,
 };
 
+/*
+ * SMSC LAN9220 Ethernet
+ */
+
+static struct resource smc91x_resources[] = {
+	{
+		.start	= PXA3xx_CS2_PHYS,
+		.end	= PXA3xx_CS2_PHYS + 0xfffff,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= gpio_to_irq(mfp_to_gpio(GPIO_ETH_IRQ)),
+		.end	= gpio_to_irq(mfp_to_gpio(GPIO_ETH_IRQ)),
+		.flags	= IORESOURCE_IRQ | IRQF_TRIGGER_FALLING,
+	}
+};
+
+static struct smsc911x_platform_config raumfeld_smsc911x_config = {
+	.phy_interface	= PHY_INTERFACE_MODE_MII,
+	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
+};
+
+static struct platform_device smc91x_device = {
+	.name		= "smsc911x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(smc91x_resources),
+	.resource	= smc91x_resources,
+	.dev		= {
+		.platform_data = &raumfeld_smsc911x_config,
+	}
+};
+
+static mfp_cfg_t raumfeld_eth_pin_config[] __initdata = {
+	GPIO1_nCS2,			/* CS */
+	GPIO40_GPIO | MFP_PULL_HIGH,	/* IRQ */
+};
+
+static void __init raumfeld_eth_init(void)
+{
+	pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_eth_pin_config));
+	platform_device_register(&smc91x_device);
+}
+
+
 static void __init raumfeld_common_init(void)
 {
 	enable_irq_wake(IRQ_WAKEUP0);
@@ -118,11 +167,13 @@ static void __init raumfeld_controller_init(void)
 static void __init raumfeld_connector_init(void)
 {
 	raumfeld_common_init();
+	raumfeld_eth_init();
 }
 
 static void __init raumfeld_speaker_init(void)
 {
 	raumfeld_common_init();
+	raumfeld_eth_init();
 }
 
 /* physical memory regions */
-- 
1.6.5.2

  parent reply	other threads:[~2009-11-25 10:42 UTC|newest]

Thread overview: 46+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-11-25 10:42 ARM: pxa: add support for Raumfeld audio devices Daniel Mack
2009-11-25 10:42 ` [PATCH 01/17] ARM: pxa/raumfeld: add basic structure for devices Daniel Mack
2009-11-25 15:26   ` Mike Rapoport
2009-11-25 15:44     ` Daniel Mack
2009-11-25 16:51     ` Marek Vasut
2009-11-25 17:06       ` Russell King - ARM Linux
2009-11-25 10:42 ` [PATCH 02/17] ARM: pxa/raumfeld: add GPIO definitions Daniel Mack
2009-11-25 10:42 ` Daniel Mack [this message]
2009-11-25 15:26   ` [PATCH 03/17] ARM: pxa/raumfeld: add SMSC9220 ethernet support Mike Rapoport
2009-11-25 15:49     ` Daniel Mack
2009-11-25 16:56       ` Russell King - ARM Linux
2009-11-26 17:55         ` Daniel Mack
2009-11-25 10:42 ` [PATCH 04/17] ARM: pxa/raumfeld: add OHCI function Daniel Mack
2009-11-25 10:42 ` [PATCH 05/17] ARM: pxa/raumfeld: add rotary encoder support Daniel Mack
2009-11-25 15:26   ` Mike Rapoport
2009-11-25 15:50     ` Daniel Mack
2009-11-25 16:59     ` Russell King - ARM Linux
2009-11-25 10:42 ` [PATCH 06/17] ARM: pxa/raumfeld: add GPIO buttons Daniel Mack
2009-11-25 10:42 ` [PATCH 07/17] ARM: pxa/raumfeld: add GPIO connected LEDs Daniel Mack
2009-11-25 10:42 ` [PATCH 08/17] ARM: pxa/raumfeld: add one-wire function Daniel Mack
2009-11-25 17:02   ` Russell King - ARM Linux
2009-11-25 10:42 ` [PATCH 09/17] ARM: pxa/raumfeld: add NAND partitions Daniel Mack
2009-11-25 15:26   ` Mike Rapoport
2009-11-25 10:42 ` [PATCH 10/17] ARM: pxa/raumfeld: add framebuffer and backlight devices Daniel Mack
2009-11-25 10:42 ` [PATCH 11/17] ARM: pxa/raumfeld: add SPI controlled devices Daniel Mack
2009-11-25 10:42 ` [PATCH 12/17] ARM: pxa/raumfeld: add audio related functions Daniel Mack
2009-11-25 11:41   ` Mark Brown
2009-11-25 12:28     ` Daniel Mack
2009-11-25 13:07       ` Mark Brown
2009-11-25 13:53         ` Daniel Mack
2009-11-25 14:00           ` Mark Brown
2009-11-25 17:07   ` Russell King - ARM Linux
2009-11-25 10:42 ` [PATCH 13/17] ARM: pxa/raumfeld: add Marvell Libertas via SDIO Daniel Mack
2009-11-25 11:49   ` Mark Brown
2009-11-25 13:04     ` Daniel Mack
2009-11-25 13:36       ` Mark Brown
2009-11-25 10:42 ` [PATCH 14/17] ARM: pxa/raumfeld: add power supply framework Daniel Mack
2009-11-25 10:42 ` [PATCH 15/17] ARM: pxa/raumfeld: add support for I2C controlled devices Daniel Mack
2009-11-25 10:42 ` [PATCH 16/17] ALSA: ARM: add Raumfeld audio support Daniel Mack
2009-11-25 11:02   ` Mark Brown
2009-11-25 12:24     ` Daniel Mack
2009-11-25 13:29       ` Mark Brown
2009-11-26 17:51         ` Daniel Mack
2009-11-25 10:42 ` [PATCH 17/17] ARM: pxa/raumfeld: Add defconfig Daniel Mack
2009-11-25 11:27 ` ARM: pxa: add support for Raumfeld audio devices Mike Rapoport
2009-11-25 12:14   ` Daniel Mack

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1259145751-3331-4-git-send-email-daniel@caiaq.de \
    --to=daniel@caiaq.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).