* LPC32XX architecture files (updated v4)
@ 2010-02-19 23:25 wellsk40 at gmail.com
2010-02-19 23:25 ` [PATCH 01/13] ARM: LPC32XX: Initial architecture header files wellsk40 at gmail.com
` (12 more replies)
0 siblings, 13 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:25 UTC (permalink / raw)
To: linux-arm-kernel
Thanks again for the review comments. This patchset is the 4rth
release with many review comments incorporated.
Changes from previous release to v4 (02/19/2010)
Review comment changes...
Removed the include/mach/board.h file until it is actually needed
Changed IRQ macros for SIC1 and SIC2 and handling in SIC1/SIC2
chained handlers
Size macros in platform.h changed to numeric values
Changed uncompress macros to use __raw_readl/writel instead of
direct register access using volatile unsigned long *
Removed unused LPC32XX_CLKPWR_SET_PLL_USBPDIV macro
printascii debug macro assembly optimized
Fixed an issue with macros using _REG being doubled casted. After
looking at this, _REG isn't really needed at all. The
macros that rely on it can use io_p2v() directly.
_REG macro removed in platform.h. Other macros that use it now
use io_p2v directly
Grammar and typo fixes
DEFINE_MUTEX used instead of init_mutex()
PLL397 and main osc clock rates hardcoded (0 rate not needed for a
disabled clock)
clock structure usecount type changes to u32
Added WARN_ON for clock disable when usecount <= 0
Clock functions pointers no longer have the address of(&) prefix
for function names, not needed
IRAM size computation algorithm changed
arch specific name changes on global platform structs specific to
the lpc32xx
LPC32xx gpiolib macro change for GPIO3 to hide pin gap details
Made pll_postdivs static in clock.c. Moved support function
(clk_get_pllrate_from_reg) from common.c that used that
function into clock.c. Prototype for support function
left in common.h (used in timer.c).
Used ffs() instead of a case block for a support function in the
clock driver
Changed clock enable/disable logic to fix an issue with clock
usecount accumulators and disable logic on failure. Clocks
are now enabled from the bottom up. This is ok on the 32xx
and makes the logic much simpler.
generic_handle_irq() used instead of handle_level_irq() for
chained handlers
SUBIRQs initially left masked, chained handler init enables them
now
suspend_valid_only_mem used instead of local variant
Small tweaks to suspend.S
icache invalidation added after SRAM copy and cache flush placed
in the correct place
Removed the ARCH specific register swap in include/amba/clcd.h
(compiles fine, but requires RK PL111 patch to work)
Montavista copyright and original GPLv2 licensing terms to pm.c
and suspend.S. INAL either, but if they get involved,
it would be easier to completely rewrite them than try
to sort out the aftermath.
Additional changes...
Added missing LPC32XX_CLKPWR_USBPDIV_PLL_MASK mask macros to USB
PCLK div computation (clock.c)
Unchanged from review comments...
IO_ADDRESS macro name unchanged. Macro is used in an existing
driver (WDT) and provides support for assembly code
that can't use the typecasts for sparse
I liked the idea of using functions for adding platform drivers
specific to different device variants, but didn't want to
do this...yet. (It makes good sense though.)
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 01/13] ARM: LPC32XX: Initial architecture header files
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
@ 2010-02-19 23:25 ` wellsk40 at gmail.com
2010-02-20 16:12 ` Uwe Kleine-König
2010-02-19 23:25 ` [PATCH 02/13] ARM: LPC32XX: Debug and IRQ macros wellsk40 at gmail.com
` (11 subsequent siblings)
12 siblings, 1 reply; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:25 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Initial header files for the LPC32XX architecture
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/include/mach/clkdev.h | 25 +
arch/arm/mach-lpc32xx/include/mach/gpio.h | 74 +++
arch/arm/mach-lpc32xx/include/mach/hardware.h | 34 ++
arch/arm/mach-lpc32xx/include/mach/i2c.h | 63 ++
arch/arm/mach-lpc32xx/include/mach/io.h | 27 +
arch/arm/mach-lpc32xx/include/mach/irqs.h | 117 ++++
arch/arm/mach-lpc32xx/include/mach/memory.h | 27 +
arch/arm/mach-lpc32xx/include/mach/platform.h | 694 +++++++++++++++++++++++
arch/arm/mach-lpc32xx/include/mach/system.h | 52 ++
arch/arm/mach-lpc32xx/include/mach/timex.h | 28 +
arch/arm/mach-lpc32xx/include/mach/uncompress.h | 60 ++
arch/arm/mach-lpc32xx/include/mach/vmalloc.h | 24 +
12 files changed, 1225 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/include/mach/clkdev.h b/arch/arm/mach-lpc32xx/include/mach/clkdev.h
new file mode 100644
index 0000000..9bf0637
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/clkdev.h
@@ -0,0 +1,25 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/clkdev.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_CLKDEV_H
+#define __ASM_ARCH_CLKDEV_H
+
+#define __clk_get(clk) ({ 1; })
+#define __clk_put(clk) do { } while (0)
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/gpio.h b/arch/arm/mach-lpc32xx/include/mach/gpio.h
new file mode 100644
index 0000000..67d03da
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/gpio.h
@@ -0,0 +1,74 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/gpio.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_GPIO_H
+#define __ASM_ARCH_GPIO_H
+
+#include <asm-generic/gpio.h>
+
+/*
+ * Note!
+ * Muxed GP pins need to be setup to the GP state in the board level
+ * code prior to using this driver.
+ * GPI pins : 28xP3 group
+ * GPO pins : 24xP3 group
+ * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
+ */
+
+#define LPC32XX_GPIO_P0_MAX 8
+#define LPC32XX_GPIO_P1_MAX 24
+#define LPC32XX_GPIO_P2_MAX 13
+#define LPC32XX_GPIO_P3_MAX 6
+#define LPC32XX_GPI_P3_MAX 28
+#define LPC32XX_GPO_P3_MAX 24
+
+#define LPC32XX_GPIO_P0_GRP 0
+#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
+#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
+#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
+#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
+#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
+
+/*
+ * A specific GPIO can be selected with this macro
+ * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+ * See the LPC32x0 User's guide for GPIO group numbers
+ */
+#define LPC32XX_GPIO(x, y) ((x) + (y))
+
+static inline int gpio_get_value(unsigned gpio)
+{
+ return __gpio_get_value(gpio);
+}
+
+static inline void gpio_set_value(unsigned gpio, int value)
+{
+ __gpio_set_value(gpio, value);
+}
+
+static inline int gpio_cansleep(unsigned gpio)
+{
+ return __gpio_cansleep(gpio);
+}
+
+static inline int gpio_to_irq(unsigned gpio)
+{
+ return __gpio_to_irq(gpio);
+}
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/hardware.h b/arch/arm/mach-lpc32xx/include/mach/hardware.h
new file mode 100644
index 0000000..33e1dde
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/hardware.h
@@ -0,0 +1,34 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/hardware.h
+ *
+ * Copyright (c) 2005 MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+/*
+ * Start of virtual addresses for IO devices
+ */
+#define IO_BASE 0xF0000000
+
+/*
+ * This macro relies on fact that for all HW i/o addresses bits 20-23 are 0
+ */
+#define IO_ADDRESS(x) (((((x) & 0xff000000) >> 4) | ((x) & 0xfffff)) |\
+ IO_BASE)
+
+#define io_p2v(x) ((void __iomem *) (unsigned long) IO_ADDRESS(x))
+#define io_v2p(x) ((((x) & 0x0ff00000) << 4) | ((x) & 0x000fffff))
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/i2c.h b/arch/arm/mach-lpc32xx/include/mach/i2c.h
new file mode 100644
index 0000000..034dc92
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/i2c.h
@@ -0,0 +1,63 @@
+/*
+ * PNX4008-specific tweaks for I2C IP3204 block
+ *
+ * Author: Vitaly Wool <vwool@ru.mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#ifndef __ASM_ARCH_I2C_H
+#define __ASM_ARCH_I2C_H
+
+enum {
+ mstatus_tdi = 0x00000001,
+ mstatus_afi = 0x00000002,
+ mstatus_nai = 0x00000004,
+ mstatus_drmi = 0x00000008,
+ mstatus_active = 0x00000020,
+ mstatus_scl = 0x00000040,
+ mstatus_sda = 0x00000080,
+ mstatus_rff = 0x00000100,
+ mstatus_rfe = 0x00000200,
+ mstatus_tff = 0x00000400,
+ mstatus_tfe = 0x00000800,
+};
+
+enum {
+ mcntrl_tdie = 0x00000001,
+ mcntrl_afie = 0x00000002,
+ mcntrl_naie = 0x00000004,
+ mcntrl_drmie = 0x00000008,
+ mcntrl_daie = 0x00000020,
+ mcntrl_rffie = 0x00000040,
+ mcntrl_tffie = 0x00000080,
+ mcntrl_reset = 0x00000100,
+ mcntrl_cdbmode = 0x00000400,
+};
+
+enum {
+ rw_bit = 1 << 0,
+ start_bit = 1 << 8,
+ stop_bit = 1 << 9,
+};
+
+#define I2C_REG_RX(a) ((a)->ioaddr) /* Rx FIFO reg (RO) */
+#define I2C_REG_TX(a) ((a)->ioaddr) /* Tx FIFO reg (WO) */
+#define I2C_REG_STS(a) ((a)->ioaddr + 0x04) /* Status reg (RO) */
+#define I2C_REG_CTL(a) ((a)->ioaddr + 0x08) /* Ctl reg */
+#define I2C_REG_CKL(a) ((a)->ioaddr + 0x0c) /* Clock divider low */
+#define I2C_REG_CKH(a) ((a)->ioaddr + 0x10) /* Clock divider high */
+#define I2C_REG_ADR(a) ((a)->ioaddr + 0x14) /* I2C address */
+#define I2C_REG_RFL(a) ((a)->ioaddr + 0x18) /* Rx FIFO level (RO) */
+#define I2C_REG_TFL(a) ((a)->ioaddr + 0x1c) /* Tx FIFO level (RO) */
+#define I2C_REG_RXB(a) ((a)->ioaddr + 0x20) /* Num of bytes Rx-ed (RO) */
+#define I2C_REG_TXB(a) ((a)->ioaddr + 0x24) /* Num of bytes Tx-ed (RO) */
+#define I2C_REG_TXS(a) ((a)->ioaddr + 0x28) /* Tx slave FIFO (RO) */
+#define I2C_REG_STFL(a) ((a)->ioaddr + 0x2c) /* Tx slave FIFO level (RO) */
+
+#define I2C_CHIP_NAME "PNX4008-I2C"
+
+#endif /* __ASM_ARCH_I2C_H */
diff --git a/arch/arm/mach-lpc32xx/include/mach/io.h b/arch/arm/mach-lpc32xx/include/mach/io.h
new file mode 100644
index 0000000..9b59ab5
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/io.h
@@ -0,0 +1,27 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/io.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARM_ARCH_IO_H
+#define __ASM_ARM_ARCH_IO_H
+
+#define IO_SPACE_LIMIT 0xffffffff
+
+#define __io(a) __typesafe_io(a)
+#define __mem_pci(a) (a)
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/irqs.h b/arch/arm/mach-lpc32xx/include/mach/irqs.h
new file mode 100644
index 0000000..2667f52
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/irqs.h
@@ -0,0 +1,117 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/irqs.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARM_ARCH_IRQS_H
+#define __ASM_ARM_ARCH_IRQS_H
+
+#define LPC32XX_SIC1_IRQ(n) (32 + (n))
+#define LPC32XX_SIC2_IRQ(n) (64 + (n))
+
+/*
+ * MIC interrupts
+ */
+#define IRQ_LPC32XX_SUB1IRQ 0
+#define IRQ_LPC32XX_SUB2IRQ 1
+#define IRQ_LPC32XX_PWM3 3
+#define IRQ_LPC32XX_PWM4 4
+#define IRQ_LPC32XX_HSTIMER 5
+#define IRQ_LPC32XX_WATCH 6
+#define IRQ_LPC32XX_UART_IIR3 7
+#define IRQ_LPC32XX_UART_IIR4 8
+#define IRQ_LPC32XX_UART_IIR5 9
+#define IRQ_LPC32XX_UART_IIR6 10
+#define IRQ_LPC32XX_FLASH 11
+#define IRQ_LPC32XX_SD1 13
+#define IRQ_LPC32XX_LCD 14
+#define IRQ_LPC32XX_SD0 15
+#define IRQ_LPC32XX_TIMER0 16
+#define IRQ_LPC32XX_TIMER1 17
+#define IRQ_LPC32XX_TIMER2 18
+#define IRQ_LPC32XX_TIMER3 19
+#define IRQ_LPC32XX_SSP0 20
+#define IRQ_LPC32XX_SSP1 21
+#define IRQ_LPC32XX_I2S0 22
+#define IRQ_LPC32XX_I2S1 23
+#define IRQ_LPC32XX_UART_IIR7 24
+#define IRQ_LPC32XX_UART_IIR2 25
+#define IRQ_LPC32XX_UART_IIR1 26
+#define IRQ_LPC32XX_MSTIMER 27
+#define IRQ_LPC32XX_DMA 28
+#define IRQ_LPC32XX_ETHERNET 29
+#define IRQ_LPC32XX_SUB1FIQ 30
+#define IRQ_LPC32XX_SUB2FIQ 31
+
+/*
+ * SIC1 interrupts start at offset 32
+ */
+#define IRQ_LPC32XX_JTAG_COMM_TX LPC32XX_SIC1_IRQ(1)
+#define IRQ_LPC32XX_JTAG_COMM_RX LPC32XX_SIC1_IRQ(2)
+#define IRQ_LPC32XX_GPI_11 LPC32XX_SIC1_IRQ(4)
+#define IRQ_LPC32XX_TS_P LPC32XX_SIC1_IRQ(6)
+#define IRQ_LPC32XX_TS_IRQ LPC32XX_SIC1_IRQ(7)
+#define IRQ_LPC32XX_TS_AUX LPC32XX_SIC1_IRQ(8)
+#define IRQ_LPC32XX_SPI2 LPC32XX_SIC1_IRQ(12)
+#define IRQ_LPC32XX_PLLUSB LPC32XX_SIC1_IRQ(13)
+#define IRQ_LPC32XX_PLLHCLK LPC32XX_SIC1_IRQ(14)
+#define IRQ_LPC32XX_PLL397 LPC32XX_SIC1_IRQ(17)
+#define IRQ_LPC32XX_I2C_2 LPC32XX_SIC1_IRQ(18)
+#define IRQ_LPC32XX_I2C_1 LPC32XX_SIC1_IRQ(19)
+#define IRQ_LPC32XX_RTC LPC32XX_SIC1_IRQ(20)
+#define IRQ_LPC32XX_KEY LPC32XX_SIC1_IRQ(22)
+#define IRQ_LPC32XX_SPI1 LPC32XX_SIC1_IRQ(23)
+#define IRQ_LPC32XX_SW LPC32XX_SIC1_IRQ(24)
+#define IRQ_LPC32XX_USB_OTG_TIMER LPC32XX_SIC1_IRQ(25)
+#define IRQ_LPC32XX_USB_OTG_ATX LPC32XX_SIC1_IRQ(26)
+#define IRQ_LPC32XX_USB_HOST LPC32XX_SIC1_IRQ(27)
+#define IRQ_LPC32XX_USB_DEV_DMA LPC32XX_SIC1_IRQ(28)
+#define IRQ_LPC32XX_USB_DEV_LP LPC32XX_SIC1_IRQ(29)
+#define IRQ_LPC32XX_USB_DEV_HP LPC32XX_SIC1_IRQ(30)
+#define IRQ_LPC32XX_USB_I2C LPC32XX_SIC1_IRQ(31)
+
+/*
+ * SIC2 interrupts start at offset 64
+ */
+#define IRQ_LPC32XX_GPIO_00 LPC32XX_SIC2_IRQ(0)
+#define IRQ_LPC32XX_GPIO_01 LPC32XX_SIC2_IRQ(1)
+#define IRQ_LPC32XX_GPIO_02 LPC32XX_SIC2_IRQ(2)
+#define IRQ_LPC32XX_GPIO_03 LPC32XX_SIC2_IRQ(3)
+#define IRQ_LPC32XX_GPIO_04 LPC32XX_SIC2_IRQ(4)
+#define IRQ_LPC32XX_GPIO_05 LPC32XX_SIC2_IRQ(5)
+#define IRQ_LPC32XX_SPI2_DATAIN LPC32XX_SIC2_IRQ(6)
+#define IRQ_LPC32XX_U2_HCTS LPC32XX_SIC2_IRQ(7)
+#define IRQ_LPC32XX_P0_P1_IRQ LPC32XX_SIC2_IRQ(8)
+#define IRQ_LPC32XX_GPI_08 LPC32XX_SIC2_IRQ(9)
+#define IRQ_LPC32XX_GPI_09 LPC32XX_SIC2_IRQ(10)
+#define IRQ_LPC32XX_GPI_19 LPC32XX_SIC2_IRQ(11)
+#define IRQ_LPC32XX_U7_HCTS LPC32XX_SIC2_IRQ(12)
+#define IRQ_LPC32XX_GPI_07 LPC32XX_SIC2_IRQ(15)
+#define IRQ_LPC32XX_SDIO LPC32XX_SIC2_IRQ(18)
+#define IRQ_LPC32XX_U5_RX LPC32XX_SIC2_IRQ(19)
+#define IRQ_LPC32XX_SPI1_DATAIN LPC32XX_SIC2_IRQ(20)
+#define IRQ_LPC32XX_GPI_00 LPC32XX_SIC2_IRQ(22)
+#define IRQ_LPC32XX_GPI_01 LPC32XX_SIC2_IRQ(23)
+#define IRQ_LPC32XX_GPI_02 LPC32XX_SIC2_IRQ(24)
+#define IRQ_LPC32XX_GPI_03 LPC32XX_SIC2_IRQ(25)
+#define IRQ_LPC32XX_GPI_04 LPC32XX_SIC2_IRQ(26)
+#define IRQ_LPC32XX_GPI_05 LPC32XX_SIC2_IRQ(27)
+#define IRQ_LPC32XX_GPI_06 LPC32XX_SIC2_IRQ(28)
+#define IRQ_LPC32XX_SYSCLK LPC32XX_SIC2_IRQ(31)
+
+#define NR_IRQS 96
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/memory.h b/arch/arm/mach-lpc32xx/include/mach/memory.h
new file mode 100644
index 0000000..044e1ac
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/memory.h
@@ -0,0 +1,27 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/memory.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+/*
+ * Physical DRAM offset of bank 0
+ */
+#define PHYS_OFFSET UL(0x80000000)
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/platform.h b/arch/arm/mach-lpc32xx/include/mach/platform.h
new file mode 100644
index 0000000..14ea8d1
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/platform.h
@@ -0,0 +1,694 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/platform.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_PLATFORM_H
+#define __ASM_ARCH_PLATFORM_H
+
+#define _SBF(f, v) ((v) << (f))
+#define _BIT(n) _SBF(n, 1)
+
+/*
+ * AHB 0 physical base addresses
+ */
+#define LPC32XX_SLC_BASE 0x20020000
+#define LPC32XX_SSP0_BASE 0x20084000
+#define LPC32XX_SPI1_BASE 0x20088000
+#define LPC32XX_SSP1_BASE 0x2008C000
+#define LPC32XX_SPI2_BASE 0x20090000
+#define LPC32XX_I2S0_BASE 0x20094000
+#define LPC32XX_SD_BASE 0x20098000
+#define LPC32XX_I2S1_BASE 0x2009C000
+#define LPC32XX_MLC_BASE 0x200A8000
+#define LPC32XX_AHB0_START LPC32XX_SLC_BASE
+#define LPC32XX_AHB0_SIZE 0x00089000
+
+/*
+ * AHB 1 physical base addresses
+ */
+#define LPC32XX_DMA_BASE 0x31000000
+#define LPC32XX_USB_BASE 0x31020000
+#define LPC32XX_USBH_BASE 0x31020000
+#define LPC32XX_USB_OTG_BASE 0x31020000
+#define LPC32XX_OTG_I2C_BASE 0x31020300
+#define LPC32XX_LCD_BASE 0x31040000
+#define LPC32XX_ETHERNET_BASE 0x31060000
+#define LPC32XX_EMC_BASE 0x31080000
+#define LPC32XX_ETB_CFG_BASE 0x310C0000
+#define LPC32XX_ETB_DATA_BASE 0x310E0000
+#define LPC32XX_AHB1_START LPC32XX_DMA_BASE
+#define LPC32XX_AHB1_SIZE 0x000E1000
+
+/*
+ * FAB physical base addresses
+ */
+#define LPC32XX_CLK_PM_BASE 0x40004000
+#define LPC32XX_MIC_BASE 0x40008000
+#define LPC32XX_SIC1_BASE 0x4000C000
+#define LPC32XX_SIC2_BASE 0x40010000
+#define LPC32XX_HS_UART1_BASE 0x40014000
+#define LPC32XX_HS_UART2_BASE 0x40018000
+#define LPC32XX_HS_UART7_BASE 0x4001C000
+#define LPC32XX_RTC_BASE 0x40024000
+#define LPC32XX_RTC_RAM_BASE 0x40024080
+#define LPC32XX_GPIO_BASE 0x40028000
+#define LPC32XX_PWM3_BASE 0x4002C000
+#define LPC32XX_PWM4_BASE 0x40030000
+#define LPC32XX_MSTIM_BASE 0x40034000
+#define LPC32XX_HSTIM_BASE 0x40038000
+#define LPC32XX_WDTIM_BASE 0x4003C000
+#define LPC32XX_DEBUG_CTRL_BASE 0x40040000
+#define LPC32XX_TIMER0_BASE 0x40044000
+#define LPC32XX_ADC_BASE 0x40048000
+#define LPC32XX_TIMER1_BASE 0x4004C000
+#define LPC32XX_KSCAN_BASE 0x40050000
+#define LPC32XX_UART_CTRL_BASE 0x40054000
+#define LPC32XX_TIMER2_BASE 0x40058000
+#define LPC32XX_PWM1_BASE 0x4005C000
+#define LPC32XX_PWM2_BASE 0x4005C004
+#define LPC32XX_TIMER3_BASE 0x40060000
+
+/*
+ * APB physical base addresses
+ */
+#define LPC32XX_UART3_BASE 0x40080000
+#define LPC32XX_UART4_BASE 0x40088000
+#define LPC32XX_UART5_BASE 0x40090000
+#define LPC32XX_UART6_BASE 0x40098000
+#define LPC32XX_I2C1_BASE 0x400A0000
+#define LPC32XX_I2C2_BASE 0x400A8000
+
+/*
+ * FAB and APB base and sizing
+ */
+#define LPC32XX_FABAPB_START LPC32XX_CLK_PM_BASE
+#define LPC32XX_FABAPB_SIZE 0x000A5000
+
+/*
+ * Internal memory bases and sizes
+ */
+#define LPC32XX_IRAM_BASE 0x08000000
+#define LPC32XX_IROM_BASE 0x0C000000
+
+/*
+ * External Static Memory Bank Address Space Bases
+ */
+#define LPC32XX_EMC_CS0_BASE 0xE0000000
+#define LPC32XX_EMC_CS1_BASE 0xE1000000
+#define LPC32XX_EMC_CS2_BASE 0xE2000000
+#define LPC32XX_EMC_CS3_BASE 0xE3000000
+
+/*
+ * External SDRAM Memory Bank Address Space Bases
+ */
+#define LPC32XX_EMC_DYCS0_BASE 0x80000000
+#define LPC32XX_EMC_DYCS1_BASE 0xA0000000
+
+/*
+ * Clock and crystal information
+ */
+#define LPC32XX_MAIN_OSC_FREQ 13000000
+#define LPC32XX_CLOCK_OSC_FREQ 32768
+
+/*
+ * Clock and Power control register offsets
+ */
+#define _PMREG(x) io_p2v(LPC32XX_CLK_PM_BASE +\
+ (x))
+#define LPC32XX_CLKPWR_DEBUG_CTRL _PMREG(0x000)
+#define LPC32XX_CLKPWR_BOOTMAP _PMREG(0x014)
+#define LPC32XX_CLKPWR_P01_ER _PMREG(0x018)
+#define LPC32XX_CLKPWR_USBCLK_PDIV _PMREG(0x01C)
+#define LPC32XX_CLKPWR_INT_ER _PMREG(0x020)
+#define LPC32XX_CLKPWR_INT_RS _PMREG(0x024)
+#define LPC32XX_CLKPWR_INT_SR _PMREG(0x028)
+#define LPC32XX_CLKPWR_INT_AP _PMREG(0x02C)
+#define LPC32XX_CLKPWR_PIN_ER _PMREG(0x030)
+#define LPC32XX_CLKPWR_PIN_RS _PMREG(0x034)
+#define LPC32XX_CLKPWR_PIN_SR _PMREG(0x038)
+#define LPC32XX_CLKPWR_PIN_AP _PMREG(0x03C)
+#define LPC32XX_CLKPWR_HCLK_DIV _PMREG(0x040)
+#define LPC32XX_CLKPWR_PWR_CTRL _PMREG(0x044)
+#define LPC32XX_CLKPWR_PLL397_CTRL _PMREG(0x048)
+#define LPC32XX_CLKPWR_MAIN_OSC_CTRL _PMREG(0x04C)
+#define LPC32XX_CLKPWR_SYSCLK_CTRL _PMREG(0x050)
+#define LPC32XX_CLKPWR_LCDCLK_CTRL _PMREG(0x054)
+#define LPC32XX_CLKPWR_HCLKPLL_CTRL _PMREG(0x058)
+#define LPC32XX_CLKPWR_ADC_CLK_CTRL_1 _PMREG(0x060)
+#define LPC32XX_CLKPWR_USB_CTRL _PMREG(0x064)
+#define LPC32XX_CLKPWR_SDRAMCLK_CTRL _PMREG(0x068)
+#define LPC32XX_CLKPWR_DDR_LAP_NOM _PMREG(0x06C)
+#define LPC32XX_CLKPWR_DDR_LAP_COUNT _PMREG(0x070)
+#define LPC32XX_CLKPWR_DDR_LAP_DELAY _PMREG(0x074)
+#define LPC32XX_CLKPWR_SSP_CLK_CTRL _PMREG(0x078)
+#define LPC32XX_CLKPWR_I2S_CLK_CTRL _PMREG(0x07C)
+#define LPC32XX_CLKPWR_MS_CTRL _PMREG(0x080)
+#define LPC32XX_CLKPWR_MACCLK_CTRL _PMREG(0x090)
+#define LPC32XX_CLKPWR_TEST_CLK_SEL _PMREG(0x0A4)
+#define LPC32XX_CLKPWR_SFW_INT _PMREG(0x0A8)
+#define LPC32XX_CLKPWR_I2C_CLK_CTRL _PMREG(0x0AC)
+#define LPC32XX_CLKPWR_KEY_CLK_CTRL _PMREG(0x0B0)
+#define LPC32XX_CLKPWR_ADC_CLK_CTRL _PMREG(0x0B4)
+#define LPC32XX_CLKPWR_PWM_CLK_CTRL _PMREG(0x0B8)
+#define LPC32XX_CLKPWR_TIMER_CLK_CTRL _PMREG(0x0BC)
+#define LPC32XX_CLKPWR_TIMERS_PWMS_CLK_CTRL_1 _PMREG(0x0C0)
+#define LPC32XX_CLKPWR_SPI_CLK_CTRL _PMREG(0x0C4)
+#define LPC32XX_CLKPWR_NAND_CLK_CTRL _PMREG(0x0C8)
+#define LPC32XX_CLKPWR_UART3_CLK_CTRL _PMREG(0x0D0)
+#define LPC32XX_CLKPWR_UART4_CLK_CTRL _PMREG(0x0D4)
+#define LPC32XX_CLKPWR_UART5_CLK_CTRL _PMREG(0x0D8)
+#define LPC32XX_CLKPWR_UART6_CLK_CTRL _PMREG(0x0DC)
+#define LPC32XX_CLKPWR_IRDA_CLK_CTRL _PMREG(0x0E0)
+#define LPC32XX_CLKPWR_UART_CLK_CTRL _PMREG(0x0E4)
+#define LPC32XX_CLKPWR_DMA_CLK_CTRL _PMREG(0x0E8)
+#define LPC32XX_CLKPWR_AUTOCLOCK _PMREG(0x0EC)
+#define LPC32XX_CLKPWR_DEVID(x) _PMREG(0x130 + (x))
+
+/*
+ * clkpwr_debug_ctrl register definitions
+*/
+#define LPC32XX_CLKPWR_VFP_CLOCK_ENABLE_BIT _BIT(4)
+
+/*
+ * clkpwr_bootmap register definitions
+ */
+#define LPC32XX_CLKPWR_BOOTMAP_SEL_BIT _BIT(1)
+
+/*
+ * clkpwr_start_gpio register bit definitions
+ */
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO23_BIT _BIT(31)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO22_BIT _BIT(30)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO21_BIT _BIT(29)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO20_BIT _BIT(28)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO19_BIT _BIT(27)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO18_BIT _BIT(26)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO17_BIT _BIT(25)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO16_BIT _BIT(24)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO15_BIT _BIT(23)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO14_BIT _BIT(22)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO13_BIT _BIT(21)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO12_BIT _BIT(20)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO11_BIT _BIT(19)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO10_BIT _BIT(18)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO9_BIT _BIT(17)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO8_BIT _BIT(16)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO7_BIT _BIT(15)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO6_BIT _BIT(14)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO5_BIT _BIT(13)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO4_BIT _BIT(12)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO3_BIT _BIT(11)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO2_BIT _BIT(10)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO1_BIT _BIT(9)
+#define LPC32XX_CLKPWR_GPIOSRC_P1IO0_BIT _BIT(8)
+#define LPC32XX_CLKPWR_GPIOSRC_P0IO7_BIT _BIT(7)
+#define LPC32XX_CLKPWR_GPIOSRC_P0IO6_BIT _BIT(6)
+#define LPC32XX_CLKPWR_GPIOSRC_P0IO5_BIT _BIT(5)
+#define LPC32XX_CLKPWR_GPIOSRC_P0IO4_BIT _BIT(4)
+#define LPC32XX_CLKPWR_GPIOSRC_P0IO3_BIT _BIT(3)
+#define LPC32XX_CLKPWR_GPIOSRC_P0IO2_BIT _BIT(2)
+#define LPC32XX_CLKPWR_GPIOSRC_P0IO1_BIT _BIT(1)
+#define LPC32XX_CLKPWR_GPIOSRC_P0IO0_BIT _BIT(0)
+
+/*
+ * clkpwr_usbclk_pdiv register definitions
+ */
+#define LPC32XX_CLKPWR_USBPDIV_PLL_MASK 0xF
+
+/*
+ * clkpwr_start_int, clkpwr_start_raw_sts_int, clkpwr_start_sts_int,
+ * clkpwr_start_pol_int, register bit definitions
+ */
+#define LPC32XX_CLKPWR_INTSRC_ADC_BIT _BIT(31)
+#define LPC32XX_CLKPWR_INTSRC_TS_P_BIT _BIT(30)
+#define LPC32XX_CLKPWR_INTSRC_TS_AUX_BIT _BIT(29)
+#define LPC32XX_CLKPWR_INTSRC_USBAHNEEDCLK_BIT _BIT(26)
+#define LPC32XX_CLKPWR_INTSRC_MSTIMER_BIT _BIT(25)
+#define LPC32XX_CLKPWR_INTSRC_RTC_BIT _BIT(24)
+#define LPC32XX_CLKPWR_INTSRC_USBNEEDCLK_BIT _BIT(23)
+#define LPC32XX_CLKPWR_INTSRC_USB_BIT _BIT(22)
+#define LPC32XX_CLKPWR_INTSRC_I2C_BIT _BIT(21)
+#define LPC32XX_CLKPWR_INTSRC_USBOTGTIMER_BIT _BIT(20)
+#define LPC32XX_CLKPWR_INTSRC_USBATXINT_BIT _BIT(19)
+#define LPC32XX_CLKPWR_INTSRC_KEY_BIT _BIT(16)
+#define LPC32XX_CLKPWR_INTSRC_MAC_BIT _BIT(7)
+#define LPC32XX_CLKPWR_INTSRC_P0P1_BIT _BIT(6)
+#define LPC32XX_CLKPWR_INTSRC_GPIO_05_BIT _BIT(5)
+#define LPC32XX_CLKPWR_INTSRC_GPIO_04_BIT _BIT(4)
+#define LPC32XX_CLKPWR_INTSRC_GPIO_03_BIT _BIT(3)
+#define LPC32XX_CLKPWR_INTSRC_GPIO_02_BIT _BIT(2)
+#define LPC32XX_CLKPWR_INTSRC_GPIO_01_BIT _BIT(1)
+#define LPC32XX_CLKPWR_INTSRC_GPIO_00_BIT _BIT(0)
+
+/*
+ * clkpwr_start_pin, clkpwr_start_raw_sts_pin, clkpwr_start_sts_pin,
+ * clkpwr_start_pol_pin register bit definitions
+ */
+#define LPC32XX_CLKPWR_EXTSRC_U7_RX_BIT _BIT(31)
+#define LPC32XX_CLKPWR_EXTSRC_U7_HCTS_BIT _BIT(30)
+#define LPC32XX_CLKPWR_EXTSRC_U6_IRRX_BIT _BIT(28)
+#define LPC32XX_CLKPWR_EXTSRC_U5_RX_BIT _BIT(26)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_28_BIT _BIT(25)
+#define LPC32XX_CLKPWR_EXTSRC_U3_RX_BIT _BIT(24)
+#define LPC32XX_CLKPWR_EXTSRC_U2_HCTS_BIT _BIT(23)
+#define LPC32XX_CLKPWR_EXTSRC_U2_RX_BIT _BIT(22)
+#define LPC32XX_CLKPWR_EXTSRC_U1_RX_BIT _BIT(21)
+#define LPC32XX_CLKPWR_EXTSRC_MSDIO_INT_BIT _BIT(18)
+#define LPC32XX_CLKPWR_EXTSRC_MSDIO_SRT_BIT _BIT(17)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_06_BIT _BIT(16)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_05_BIT _BIT(15)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_04_BIT _BIT(14)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_03_BIT _BIT(13)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_02_BIT _BIT(12)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_01_BIT _BIT(11)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_00_BIT _BIT(10)
+#define LPC32XX_CLKPWR_EXTSRC_SYSCLKEN_BIT _BIT(9)
+#define LPC32XX_CLKPWR_EXTSRC_SPI1_DATIN_BIT _BIT(8)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_07_BIT _BIT(7)
+#define LPC32XX_CLKPWR_EXTSRC_SPI2_DATIN_BIT _BIT(6)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_19_BIT _BIT(5)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_09_BIT _BIT(4)
+#define LPC32XX_CLKPWR_EXTSRC_GPI_08_BIT _BIT(3)
+
+/*
+ * clkpwr_hclk_div register definitions
+ */
+#define LPC32XX_CLKPWR_HCLKDIV_DDRCLK_STOP (0x0 << 7)
+#define LPC32XX_CLKPWR_HCLKDIV_DDRCLK_NORM (0x1 << 7)
+#define LPC32XX_CLKPWR_HCLKDIV_DDRCLK_HALF (0x2 << 7)
+#define LPC32XX_CLKPWR_HCLKDIV_PCLK_DIV(n) (((n) & 0x1F) << 2)
+#define LPC32XX_CLKPWR_HCLKDIV_DIV_2POW(n) ((n) & 0x3)
+
+/*
+ * clkpwr_pwr_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_CTRL_FORCE_PCLK _BIT(10)
+#define LPC32XX_CLKPWR_SDRAM_SELF_RFSH _BIT(9)
+#define LPC32XX_CLKPWR_UPD_SDRAM_SELF_RFSH _BIT(8)
+#define LPC32XX_CLKPWR_AUTO_SDRAM_SELF_RFSH _BIT(7)
+#define LPC32XX_CLKPWR_HIGHCORE_STATE_BIT _BIT(5)
+#define LPC32XX_CLKPWR_SYSCLKEN_STATE_BIT _BIT(4)
+#define LPC32XX_CLKPWR_SYSCLKEN_GPIO_EN _BIT(3)
+#define LPC32XX_CLKPWR_SELECT_RUN_MODE _BIT(2)
+#define LPC32XX_CLKPWR_HIGHCORE_GPIO_EN _BIT(1)
+#define LPC32XX_CLKPWR_STOP_MODE_CTRL _BIT(0)
+
+/*
+ * clkpwr_pll397_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_PLL397_MSLOCK_STS _BIT(10)
+#define LPC32XX_CLKPWR_PLL397_BYPASS _BIT(9)
+#define LPC32XX_CLKPWR_PLL397_BIAS_NORM 0x000
+#define LPC32XX_CLKPWR_PLL397_BIAS_N12_5 0x040
+#define LPC32XX_CLKPWR_PLL397_BIAS_N25 0x080
+#define LPC32XX_CLKPWR_PLL397_BIAS_N37_5 0x0C0
+#define LPC32XX_CLKPWR_PLL397_BIAS_P12_5 0x100
+#define LPC32XX_CLKPWR_PLL397_BIAS_P25 0x140
+#define LPC32XX_CLKPWR_PLL397_BIAS_P37_5 0x180
+#define LPC32XX_CLKPWR_PLL397_BIAS_P50 0x1C0
+#define LPC32XX_CLKPWR_PLL397_BIAS_MASK 0x1C0
+#define LPC32XX_CLKPWR_SYSCTRL_PLL397_DIS _BIT(1)
+#define LPC32XX_CLKPWR_SYSCTRL_PLL397_STS _BIT(0)
+
+/*
+ * clkpwr_main_osc_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_MOSC_ADD_CAP(n) (((n) & 0x7F) << 2)
+#define LPC32XX_CLKPWR_MOSC_CAP_MASK (0x7F << 2)
+#define LPC32XX_CLKPWR_TEST_MODE _BIT(1)
+#define LPC32XX_CLKPWR_MOSC_DISABLE _BIT(0)
+
+/*
+ * clkpwr_sysclk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_SYSCTRL_BP_TRIG(n) (((n) & 0x3FF) << 2)
+#define LPC32XX_CLKPWR_SYSCTRL_BP_MASK (0x3FF << 2)
+#define LPC32XX_CLKPWR_SYSCTRL_USEPLL397 _BIT(1)
+#define LPC32XX_CLKPWR_SYSCTRL_SYSCLKMUX _BIT(0)
+
+/*
+ * clkpwr_lcdclk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT12 0x000
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16 0x040
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT15 0x080
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT24 0x0C0
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_STN4M 0x100
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_STN8C 0x140
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_DSTN4M 0x180
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_DSTN8C 0x1C0
+#define LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK 0x01C0
+#define LPC32XX_CLKPWR_LCDCTRL_CLK_EN 0x020
+#define LPC32XX_CLKPWR_LCDCTRL_SET_PSCALE(n) ((n - 1) & 0x1F)
+#define LPC32XX_CLKPWR_LCDCTRL_PSCALE_MSK 0x001F
+
+/*
+ * clkpwr_hclkpll_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_HCLKPLL_POWER_UP _BIT(16)
+#define LPC32XX_CLKPWR_HCLKPLL_CCO_BYPASS _BIT(15)
+#define LPC32XX_CLKPWR_HCLKPLL_POSTDIV_BYPASS _BIT(14)
+#define LPC32XX_CLKPWR_HCLKPLL_FDBK_SEL_FCLK _BIT(13)
+#define LPC32XX_CLKPWR_HCLKPLL_POSTDIV_2POW(n) (((n) & 0x3) << 11)
+#define LPC32XX_CLKPWR_HCLKPLL_PREDIV_PLUS1(n) (((n) & 0x3) << 9)
+#define LPC32XX_CLKPWR_HCLKPLL_PLLM(n) (((n) & 0xFF) << 1)
+#define LPC32XX_CLKPWR_HCLKPLL_PLL_STS _BIT(0)
+
+/*
+ * clkpwr_adc_clk_ctrl_1 register definitions
+ */
+#define LPC32XX_CLKPWR_ADCCTRL1_RTDIV(n) (((n) & 0xFF) << 0)
+#define LPC32XX_CLKPWR_ADCCTRL1_PCLK_SEL _BIT(8)
+
+/*
+ * clkpwr_usb_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_USBCTRL_HCLK_EN _BIT(24)
+#define LPC32XX_CLKPWR_USBCTRL_USBI2C_EN _BIT(23)
+#define LPC32XX_CLKPWR_USBCTRL_USBDVND_EN _BIT(22)
+#define LPC32XX_CLKPWR_USBCTRL_USBHSTND_EN _BIT(21)
+#define LPC32XX_CLKPWR_USBCTRL_PU_ADD (0x0 << 19)
+#define LPC32XX_CLKPWR_USBCTRL_BUS_KEEPER (0x1 << 19)
+#define LPC32XX_CLKPWR_USBCTRL_PD_ADD (0x3 << 19)
+#define LPC32XX_CLKPWR_USBCTRL_CLK_EN2 _BIT(18)
+#define LPC32XX_CLKPWR_USBCTRL_CLK_EN1 _BIT(17)
+#define LPC32XX_CLKPWR_USBCTRL_PLL_PWRUP _BIT(16)
+#define LPC32XX_CLKPWR_USBCTRL_CCO_BYPASS _BIT(15)
+#define LPC32XX_CLKPWR_USBCTRL_POSTDIV_BYPASS _BIT(14)
+#define LPC32XX_CLKPWR_USBCTRL_FDBK_SEL_FCLK _BIT(13)
+#define LPC32XX_CLKPWR_USBCTRL_POSTDIV_2POW(n) (((n) & 0x3) << 11)
+#define LPC32XX_CLKPWR_USBCTRL_PREDIV_PLUS1(n) (((n) & 0x3) << 9)
+#define LPC32XX_CLKPWR_USBCTRL_FDBK_PLUS1(n) (((n) & 0xFF) << 1)
+#define LPC32XX_CLKPWR_USBCTRL_PLL_STS _BIT(0)
+
+/*
+ * clkpwr_sdramclk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_SDRCLK_FASTSLEW_CLK _BIT(22)
+#define LPC32XX_CLKPWR_SDRCLK_FASTSLEW _BIT(21)
+#define LPC32XX_CLKPWR_SDRCLK_FASTSLEW_DAT _BIT(20)
+#define LPC32XX_CLKPWR_SDRCLK_SW_DDR_RESET _BIT(19)
+#define LPC32XX_CLKPWR_SDRCLK_HCLK_DLY(n) (((n) & 0x1F) << 14)
+#define LPC32XX_CLKPWR_SDRCLK_DLY_ADDR_STS _BIT(13)
+#define LPC32XX_CLKPWR_SDRCLK_SENS_FACT(n) (((n) & 0x7) << 10)
+#define LPC32XX_CLKPWR_SDRCLK_USE_CAL _BIT(9)
+#define LPC32XX_CLKPWR_SDRCLK_DO_CAL _BIT(8)
+#define LPC32XX_CLKPWR_SDRCLK_CAL_ON_RTC _BIT(7)
+#define LPC32XX_CLKPWR_SDRCLK_DQS_DLY(n) (((n) & 0x1F) << 2)
+#define LPC32XX_CLKPWR_SDRCLK_USE_DDR _BIT(1)
+#define LPC32XX_CLKPWR_SDRCLK_CLK_DIS _BIT(0)
+
+/*
+ * clkpwr_ssp_blk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_SSPCTRL_DMA_SSP1RX _BIT(5)
+#define LPC32XX_CLKPWR_SSPCTRL_DMA_SSP1TX _BIT(4)
+#define LPC32XX_CLKPWR_SSPCTRL_DMA_SSP0RX _BIT(3)
+#define LPC32XX_CLKPWR_SSPCTRL_DMA_SSP0TX _BIT(2)
+#define LPC32XX_CLKPWR_SSPCTRL_SSPCLK1_EN _BIT(1)
+#define LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN _BIT(0)
+
+/*
+ * clkpwr_i2s_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_I2SCTRL_I2S1_RX_FOR_TX _BIT(6)
+#define LPC32XX_CLKPWR_I2SCTRL_I2S1_TX_FOR_RX _BIT(5)
+#define LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA _BIT(4)
+#define LPC32XX_CLKPWR_I2SCTRL_I2S0_RX_FOR_TX _BIT(3)
+#define LPC32XX_CLKPWR_I2SCTRL_I2S0_TX_FOR_RX _BIT(2)
+#define LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN _BIT(1)
+#define LPC32XX_CLKPWR_I2SCTRL_I2SCLK0_EN _BIT(0)
+
+/*
+ * clkpwr_ms_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_MSCARD_MSDIO_PIN_DIS _BIT(10)
+#define LPC32XX_CLKPWR_MSCARD_MSDIO_PU_EN _BIT(9)
+#define LPC32XX_CLKPWR_MSCARD_MSDIO23_DIS _BIT(8)
+#define LPC32XX_CLKPWR_MSCARD_MSDIO1_DIS _BIT(7)
+#define LPC32XX_CLKPWR_MSCARD_MSDIO0_DIS _BIT(6)
+#define LPC32XX_CLKPWR_MSCARD_SDCARD_EN _BIT(5)
+#define LPC32XX_CLKPWR_MSCARD_SDCARD_DIV(n) ((n) & 0xF)
+
+/*
+ * clkpwr_macclk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_MACCTRL_NO_ENET_PIS 0x00
+#define LPC32XX_CLKPWR_MACCTRL_USE_MII_PINS 0x08
+#define LPC32XX_CLKPWR_MACCTRL_USE_RMII_PINS 0x18
+#define LPC32XX_CLKPWR_MACCTRL_PINS_MSK 0x18
+#define LPC32XX_CLKPWR_MACCTRL_DMACLK_EN _BIT(2)
+#define LPC32XX_CLKPWR_MACCTRL_MMIOCLK_EN _BIT(1)
+#define LPC32XX_CLKPWR_MACCTRL_HRCCLK_EN _BIT(0)
+
+/*
+ * clkpwr_test_clk_sel register definitions
+ */
+#define LPC32XX_CLKPWR_TESTCLK1_SEL_PERCLK (0x0 << 5)
+#define LPC32XX_CLKPWR_TESTCLK1_SEL_RTC (0x1 << 5)
+#define LPC32XX_CLKPWR_TESTCLK1_SEL_MOSC (0x2 << 5)
+#define LPC32XX_CLKPWR_TESTCLK1_SEL_MASK (0x3 << 5)
+#define LPC32XX_CLKPWR_TESTCLK_TESTCLK1_EN _BIT(4)
+#define LPC32XX_CLKPWR_TESTCLK2_SEL_HCLK (0x0 << 1)
+#define LPC32XX_CLKPWR_TESTCLK2_SEL_PERCLK (0x1 << 1)
+#define LPC32XX_CLKPWR_TESTCLK2_SEL_USBCLK (0x2 << 1)
+#define LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC (0x5 << 1)
+#define LPC32XX_CLKPWR_TESTCLK2_SEL_PLL397 (0x7 << 1)
+#define LPC32XX_CLKPWR_TESTCLK2_SEL_MASK (0x7 << 1)
+#define LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN _BIT(0)
+
+/*
+ * clkpwr_sw_int register definitions
+ */
+#define LPC32XX_CLKPWR_SW_INT(n) (_BIT(0) | (((n) & 0x7F) << 1))
+#define LPC32XX_CLKPWR_SW_GET_ARG(n) (((n) & 0xFE) >> 1)
+
+/*
+ * clkpwr_i2c_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE _BIT(4)
+#define LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE _BIT(3)
+#define LPC32XX_CLKPWR_I2CCLK_I2C1HI_DRIVE _BIT(2)
+#define LPC32XX_CLKPWR_I2CCLK_I2C2CLK_EN _BIT(1)
+#define LPC32XX_CLKPWR_I2CCLK_I2C1CLK_EN _BIT(0)
+
+/*
+ * clkpwr_key_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_KEYCLKCTRL_CLK_EN 0x1
+
+/*
+ * clkpwr_adc_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_ADC32CLKCTRL_CLK_EN 0x1
+
+/*
+ * clkpwr_pwm_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_PWMCLK_PWM2_DIV(n) (((n) & 0xF) << 8)
+#define LPC32XX_CLKPWR_PWMCLK_PWM1_DIV(n) (((n) & 0xF) << 4)
+#define LPC32XX_CLKPWR_PWMCLK_PWM2SEL_PCLK 0x8
+#define LPC32XX_CLKPWR_PWMCLK_PWM2CLK_EN 0x4
+#define LPC32XX_CLKPWR_PWMCLK_PWM1SEL_PCLK 0x2
+#define LPC32XX_CLKPWR_PWMCLK_PWM1CLK_EN 0x1
+
+/*
+ * clkpwr_timer_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_PWMCLK_HSTIMER_EN 0x2
+#define LPC32XX_CLKPWR_PWMCLK_WDOG_EN 0x1
+
+/*
+ * clkpwr_timers_pwms_clk_ctrl_1 register definitions
+ */
+#define LPC32XX_CLKPWR_TMRPWMCLK_TIMER3_EN 0x20
+#define LPC32XX_CLKPWR_TMRPWMCLK_TIMER2_EN 0x10
+#define LPC32XX_CLKPWR_TMRPWMCLK_TIMER1_EN 0x08
+#define LPC32XX_CLKPWR_TMRPWMCLK_TIMER0_EN 0x04
+#define LPC32XX_CLKPWR_TMRPWMCLK_PWM4_EN 0x02
+#define LPC32XX_CLKPWR_TMRPWMCLK_PWM3_EN 0x01
+
+/*
+ * clkpwr_spi_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_SPICLK_SET_SPI2DATIO 0x80
+#define LPC32XX_CLKPWR_SPICLK_SET_SPI2CLK 0x40
+#define LPC32XX_CLKPWR_SPICLK_USE_SPI2 0x20
+#define LPC32XX_CLKPWR_SPICLK_SPI2CLK_EN 0x10
+#define LPC32XX_CLKPWR_SPICLK_SET_SPI1DATIO 0x08
+#define LPC32XX_CLKPWR_SPICLK_SET_SPI1CLK 0x04
+#define LPC32XX_CLKPWR_SPICLK_USE_SPI1 0x02
+#define LPC32XX_CLKPWR_SPICLK_SPI1CLK_EN 0x01
+
+/*
+ * clkpwr_nand_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_NANDCLK_INTSEL_MLC 0x20
+#define LPC32XX_CLKPWR_NANDCLK_DMA_RNB 0x10
+#define LPC32XX_CLKPWR_NANDCLK_DMA_INT 0x08
+#define LPC32XX_CLKPWR_NANDCLK_SEL_SLC 0x04
+#define LPC32XX_CLKPWR_NANDCLK_MLCCLK_EN 0x02
+#define LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN 0x01
+
+/*
+ * clkpwr_uart3_clk_ctrl, clkpwr_uart4_clk_ctrl, clkpwr_uart5_clk_ctrl
+ * and clkpwr_uart6_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_UART_Y_DIV(y) ((y) & 0xFF)
+#define LPC32XX_CLKPWR_UART_X_DIV(x) (((x) & 0xFF) << 8)
+#define LPC32XX_CLKPWR_UART_USE_HCLK _BIT(16)
+
+/*
+ * clkpwr_irda_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_IRDA_Y_DIV(y) ((y) & 0xFF)
+#define LPC32XX_CLKPWR_IRDA_X_DIV(x) (((x) & 0xFF) << 8)
+
+/*
+ * clkpwr_uart_clk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_UARTCLKCTRL_UART6_EN _BIT(3)
+#define LPC32XX_CLKPWR_UARTCLKCTRL_UART5_EN _BIT(2)
+#define LPC32XX_CLKPWR_UARTCLKCTRL_UART4_EN _BIT(1)
+#define LPC32XX_CLKPWR_UARTCLKCTRL_UART3_EN _BIT(0)
+
+/*
+ * clkpwr_dmaclk_ctrl register definitions
+ */
+#define LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN 0x1
+
+/*
+ * clkpwr_autoclock register definitions
+ */
+#define LPC32XX_CLKPWR_AUTOCLK_USB_EN 0x40
+#define LPC32XX_CLKPWR_AUTOCLK_IRAM_EN 0x02
+#define LPC32XX_CLKPWR_AUTOCLK_IROM_EN 0x01
+
+/*
+ * Interrupt controller register offsets
+ */
+#define LPC32XX_INTC_MASK(x) io_p2v((x) + 0x00)
+#define LPC32XX_INTC_RAW_STAT(x) io_p2v((x) + 0x04)
+#define LPC32XX_INTC_STAT(x) io_p2v((x) + 0x08)
+#define LPC32XX_INTC_POLAR(x) io_p2v((x) + 0x0C)
+#define LPC32XX_INTC_ACT_TYPE(x) io_p2v((x) + 0x10)
+#define LPC32XX_INTC_TYPE(x) io_p2v((x) + 0x14)
+
+/*
+ * Timer/counter register offsets
+ */
+#define LCP32XX_TIMER_IR(x) io_p2v((x) + 0x00)
+#define LCP32XX_TIMER_TCR(x) io_p2v((x) + 0x04)
+#define LCP32XX_TIMER_TC(x) io_p2v((x) + 0x08)
+#define LCP32XX_TIMER_PR(x) io_p2v((x) + 0x0C)
+#define LCP32XX_TIMER_PC(x) io_p2v((x) + 0x10)
+#define LCP32XX_TIMER_MCR(x) io_p2v((x) + 0x14)
+#define LCP32XX_TIMER_MR0(x) io_p2v((x) + 0x18)
+#define LCP32XX_TIMER_MR1(x) io_p2v((x) + 0x1C)
+#define LCP32XX_TIMER_MR2(x) io_p2v((x) + 0x20)
+#define LCP32XX_TIMER_MR3(x) io_p2v((x) + 0x24)
+#define LCP32XX_TIMER_CCR(x) io_p2v((x) + 0x28)
+#define LCP32XX_TIMER_CR0(x) io_p2v((x) + 0x2C)
+#define LCP32XX_TIMER_CR1(x) io_p2v((x) + 0x30)
+#define LCP32XX_TIMER_CR2(x) io_p2v((x) + 0x34)
+#define LCP32XX_TIMER_CR3(x) io_p2v((x) + 0x38)
+#define LCP32XX_TIMER_EMR(x) io_p2v((x) + 0x3C)
+#define LCP32XX_TIMER_CTCR(x) io_p2v((x) + 0x70)
+
+/*
+ * ir register definitions
+ */
+#define LCP32XX_TIMER_CNTR_MTCH_BIT(n) (1 << ((n) & 0x3))
+#define LCP32XX_TIMER_CNTR_CAPT_BIT(n) (1 << (4 + ((n) & 0x3)))
+
+/*
+ * tcr register definitions
+ */
+#define LCP32XX_TIMER_CNTR_TCR_EN 0x1
+#define LCP32XX_TIMER_CNTR_TCR_RESET 0x2
+
+/*
+ * mcr register definitions
+ */
+#define LCP32XX_TIMER_CNTR_MCR_MTCH(n) (0x1 << ((n) * 3))
+#define LCP32XX_TIMER_CNTR_MCR_RESET(n) (0x1 << (((n) * 3) + 1))
+#define LCP32XX_TIMER_CNTR_MCR_STOP(n) (0x1 << (((n) * 3) + 2))
+
+/*
+ * Standard UART register offsets
+ */
+#define LPC32XX_UART_DLL_FIFO(x) io_p2v((x) + 0x00)
+#define LPC32XX_UART_DLM_IER(x) io_p2v((x) + 0x04)
+#define LPC32XX_UART_IIR_FCR(x) io_p2v((x) + 0x08)
+#define LPC32XX_UART_LCR(x) io_p2v((x) + 0x0C)
+#define LPC32XX_UART_MODEM_CTRL(x) io_p2v((x) + 0x10)
+#define LPC32XX_UART_LSR(x) io_p2v((x) + 0x14)
+#define LPC32XX_UART_MODEM_STATUS(x) io_p2v((x) + 0x18)
+#define LPC32XX_UART_RXLEV(x) io_p2v((x) + 0x1C)
+
+/*
+ * UART control structure offsets
+ */
+#define _UCREG(x) io_p2v(\
+ LPC32XX_UART_CTRL_BASE + (x))
+#define LPC32XX_UARTCTL_CTRL _UCREG(0x00)
+#define LPC32XX_UARTCTL_CLKMODE _UCREG(0x04)
+#define LPC32XX_UARTCTL_CLOOP _UCREG(0x08)
+
+/*
+ * ctrl register definitions
+ */
+#define LPC32XX_UART_U3_MD_CTRL_EN _BIT(11)
+#define LPC32XX_UART_IRRX6_INV_EN _BIT(10)
+#define LPC32XX_UART_HDPX_EN _BIT(9)
+#define LPC32XX_UART_UART6_IRDAMOD_BYPASS _BIT(5)
+#define LPC32XX_RT_IRTX6_INV_EN _BIT(4)
+#define LPC32XX_RT_IRTX6_INV_MIR_EN _BIT(3)
+#define LPC32XX_RT_RX_IRPULSE_3_16_115K _BIT(2)
+#define LPC32XX_RT_TX_IRPULSE_3_16_115K _BIT(1)
+#define LPC32XX_UART_U5_ROUTE_TO_USB _BIT(0)
+
+/*
+ * clkmode register definitions
+ */
+#define LPC32XX_UART_ENABLED_CLOCKS(n) (((n) >> 16) & 0x7F)
+#define LPC32XX_UART_ENABLED_CLOCK(n, u) (((n) >> (16 + (u))) & 0x1)
+#define LPC32XX_UART_ENABLED_CLKS_ANY _BIT(14)
+#define LPC32XX_UART_CLKMODE_OFF 0x0
+#define LPC32XX_UART_CLKMODE_ON 0x1
+#define LPC32XX_UART_CLKMODE_AUTO 0x2
+#define LPC32XX_UART_CLKMODE_MASK(u) (0x3 << ((((u) - 3) * 2) + 4))
+#define LPC32XX_UART_CLKMODE_LOAD(m, u) ((m) << ((((u) - 3) * 2) + 4))
+
+/*
+ * GPIO Module Register offsets
+ */
+#define _GPREG(x) io_p2v(LPC32XX_GPIO_BASE + (x))
+#define LPC32XX_GPIO_P_MUX_SET _GPREG(0x100)
+#define LPC32XX_GPIO_P_MUX_CLR _GPREG(0x104)
+#define LPC32XX_GPIO_P_MUX_STATE _GPREG(0x108)
+#define LPC32XX_GPIO_P3_MUX_SET _GPREG(0x110)
+#define LPC32XX_GPIO_P3_MUX_CLR _GPREG(0x114)
+#define LPC32XX_GPIO_P3_MUX_STATE _GPREG(0x118)
+#define LPC32XX_GPIO_P0_MUX_SET _GPREG(0x120)
+#define LPC32XX_GPIO_P0_MUX_CLR _GPREG(0x124)
+#define LPC32XX_GPIO_P0_MUX_STATE _GPREG(0x128)
+#define LPC32XX_GPIO_P1_MUX_SET _GPREG(0x130)
+#define LPC32XX_GPIO_P1_MUX_CLR _GPREG(0x134)
+#define LPC32XX_GPIO_P1_MUX_STATE _GPREG(0x138)
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/system.h b/arch/arm/mach-lpc32xx/include/mach/system.h
new file mode 100644
index 0000000..df3b0de
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/system.h
@@ -0,0 +1,52 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/system.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H
+
+static void arch_idle(void)
+{
+ cpu_do_idle();
+}
+
+static inline void arch_reset(char mode, const char *cmd)
+{
+ extern void lpc32xx_watchdog_reset(void);
+
+ switch (mode) {
+ case 's':
+ case 'h':
+ printk(KERN_CRIT "RESET: Rebooting system\n");
+
+ /* Disable interrupts */
+ local_irq_disable();
+
+ lpc32xx_watchdog_reset();
+ break;
+
+ default:
+ /* Do nothing */
+ break;
+ }
+
+ /* Wait for watchdog to reset system */
+ while (1)
+ ;
+}
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/timex.h b/arch/arm/mach-lpc32xx/include/mach/timex.h
new file mode 100644
index 0000000..8d4066b
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/timex.h
@@ -0,0 +1,28 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/timex.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_TIMEX_H
+#define __ASM_ARCH_TIMEX_H
+
+/*
+ * Rate in Hz of the main system oscillator. This value should match
+ * the value 'MAIN_OSC_FREQ' in platform.h
+ */
+#define CLOCK_TICK_RATE 13000000
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/uncompress.h b/arch/arm/mach-lpc32xx/include/mach/uncompress.h
new file mode 100644
index 0000000..c142487
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/uncompress.h
@@ -0,0 +1,60 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/uncompress.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARM_ARCH_UNCOMPRESS_H
+#define __ASM_ARM_ARCH_UNCOMPRESS_H
+
+#include <linux/io.h>
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+
+/*
+ * Uncompress output is hardcoded to standard UART 5
+ */
+
+#define UART_FIFO_CTL_TX_RESET (1 << 2)
+#define UART_STATUS_TX_MT (1 << 6)
+
+#define _UARTREG(x) (void __iomem *)(LPC32XX_UART5_BASE + (x))
+
+#define LPC32XX_UART_DLLFIFO_O 0x00
+#define LPC32XX_UART_IIRFCR_O 0x08
+#define LPC32XX_UART_LSR_O 0x14
+
+static inline void putc(int ch)
+{
+ /* Wait for transmit FIFO to empty */
+ while ((__raw_readl(_UARTREG(LPC32XX_UART_LSR_O)) &
+ UART_STATUS_TX_MT) == 0)
+ ;
+
+ __raw_writel((u32) ch, _UARTREG(LPC32XX_UART_DLLFIFO_O));
+}
+
+static inline void flush(void)
+{
+ __raw_writel(__raw_readl(_UARTREG(LPC32XX_UART_IIRFCR_O)) |
+ UART_FIFO_CTL_TX_RESET, _UARTREG(LPC32XX_UART_IIRFCR_O));
+}
+
+/* NULL functions; we don't presently need them */
+#define arch_decomp_setup()
+#define arch_decomp_wdog()
+
+#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/vmalloc.h b/arch/arm/mach-lpc32xx/include/mach/vmalloc.h
new file mode 100644
index 0000000..d1d936c
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/vmalloc.h
@@ -0,0 +1,24 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/vmalloc.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_VMALLOC_H
+#define __ASM_ARCH_VMALLOC_H
+
+#define VMALLOC_END 0xF0000000
+
+#endif
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 02/13] ARM: LPC32XX: Debug and IRQ macros
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
2010-02-19 23:25 ` [PATCH 01/13] ARM: LPC32XX: Initial architecture header files wellsk40 at gmail.com
@ 2010-02-19 23:25 ` wellsk40 at gmail.com
2010-02-19 23:25 ` [PATCH 03/13] ARM: LPC32XX: Clock driver wellsk40 at gmail.com
` (10 subsequent siblings)
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:25 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Debug (printascii) and IRQ handler macros for the LPC32XX
architecture
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/include/mach/debug-macro.S | 54 ++++++++++++++++++++++
arch/arm/mach-lpc32xx/include/mach/entry-macro.S | 47 +++++++++++++++++++
2 files changed, 101 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/include/mach/debug-macro.S b/arch/arm/mach-lpc32xx/include/mach/debug-macro.S
new file mode 100644
index 0000000..66b7acc
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/debug-macro.S
@@ -0,0 +1,54 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/debug-macro.S
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+
+#define LPC32XX_UART_DLL_FIFO_OFS 0x00
+#define LPC32XX_UART_LSR_OFS 0x14
+
+#define LPC32XX_UART_DEBUG_BASE LPC32XX_UART5_BASE
+
+/*
+ * Debug output is hardcoded to standard UART 5
+*/
+
+ .macro addruart,rx
+ mrc p15, 0, \rx, c1, c0
+ tst \rx, #1 @ MMU enabled?
+ ldreq \rx, =LPC32XX_UART_DEBUG_BASE @ physical
+ ldrne \rx, =IO_ADDRESS(LPCLPC32XX_UART_DEBUG_BASE) @ virtual
+ .endm
+
+ .macro senduart,rd,rx
+ str \rd, [\rx, #LPC32XX_UART_DLL_FIFO_OFS]
+ .endm
+
+ .macro busyuart,rd,rx
+1002:
+ ldr \rd, [\rx, #LPC32XX_UART_LSR_OFS]
+ tst \rd, #(1 << 6)
+ beq 1002b
+ .endm
+
+ .macro waituart,rd,rx
+1001:
+ ldr \rd, [\rx, #LPC32XX_UART_LSR_OFS]
+ tst \rd, #(1 << 5)
+ beq 1001b
+ .endm
diff --git a/arch/arm/mach-lpc32xx/include/mach/entry-macro.S b/arch/arm/mach-lpc32xx/include/mach/entry-macro.S
new file mode 100644
index 0000000..870227c
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/include/mach/entry-macro.S
@@ -0,0 +1,47 @@
+/*
+ * arch/arm/mach-lpc32xx/include/mach/entry-macro.S
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+
+#define LPC32XX_INTC_MASKED_STATUS_OFS 0x8
+
+ .macro disable_fiq
+ .endm
+
+ .macro get_irqnr_preamble, base, tmp
+ ldr \base, =IO_ADDRESS(LPC32XX_MIC_BASE)
+ .endm
+
+ .macro arch_ret_to_user, tmp1, tmp2
+ .endm
+
+/*
+ * Return IRQ number in irqnr. Also return processor Z flag status in CPSR
+ * as set if an interrupt is pending.
+ */
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+ ldr \irqstat, [\base, #LPC32XX_INTC_MASKED_STATUS_OFS]
+ clz \irqnr, \irqstat
+ rsb \irqnr, \irqnr, #31
+ teq \irqstat, #0
+ .endm
+
+ .macro irq_prio_table
+ .endm
+
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 03/13] ARM: LPC32XX: Clock driver
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
2010-02-19 23:25 ` [PATCH 01/13] ARM: LPC32XX: Initial architecture header files wellsk40 at gmail.com
2010-02-19 23:25 ` [PATCH 02/13] ARM: LPC32XX: Debug and IRQ macros wellsk40 at gmail.com
@ 2010-02-19 23:25 ` wellsk40 at gmail.com
2010-02-20 16:33 ` Russell King - ARM Linux
2010-02-19 23:26 ` [PATCH 04/13] ARM: LPC32XX: GPIO, timer, and IRQ drivers wellsk40 at gmail.com
` (9 subsequent siblings)
12 siblings, 1 reply; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:25 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Clock driver for the LPC32XX architecture
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/clock.c | 1086 +++++++++++++++++++++++++++++++++++++++++
arch/arm/mach-lpc32xx/clock.h | 37 ++
2 files changed, 1123 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/clock.c b/arch/arm/mach-lpc32xx/clock.c
new file mode 100644
index 0000000..a1e8ee3
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/clock.c
@@ -0,0 +1,1086 @@
+/*
+ * arch/arm/mach-lpc32xx/clock.c
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * LPC32xx clock management driver overview
+ *
+ * The LPC32XX contains a number of high level system clocks that can be
+ * generated from different sources. These system clocks are used to
+ * generate the CPU and bus rates and the individual peripheral clocks in
+ * the system. When Linux is started by the boot loader, the system
+ * clocks are already running. Stopping a system clock during normal
+ * Linux operation should never be attempted, as peripherals that require
+ * those clocks will quit working (ie, DRAM).
+ *
+ * The LPC32xx high level clock tree looks as follows. Clocks marked with
+ * an asterisk are always on and cannot be disabled. Clocks marked with
+ * an ampersand can only be disabled in CPU suspend mode. Clocks marked
+ * with a caret are always on if it is the selected clock for the SYSCLK
+ * source. The clock that isn't used for SYSCLK can be enabled and
+ * disabled normally.
+ * 32KHz oscillator*
+ * / | \
+ * RTC* PLL397^ TOUCH
+ * /
+ * Main oscillator^ /
+ * | \ /
+ * | SYSCLK&
+ * | \
+ * | \
+ * USB_PLL HCLK_PLL&
+ * | | |
+ * USB host/device PCLK& |
+ * | |
+ * Peripherals
+ *
+ * The CPU and chip bus rates are derived from the HCLK PLL, which can
+ * generate various clock rates up to 266MHz and beyond. The internal bus
+ * rates (PCLK and HCLK) are generated from dividers based on the HCLK
+ * PLL rate. HCLK can be a ratio of 1:1, 1:2, or 1:4 or HCLK PLL rate,
+ * while PCLK can be 1:1 to 1:32 of HCLK PLL rate. Most peripherals high
+ * level clocks are based on either HCLK or PCLK, but have their own
+ * dividers as part of the IP itself. Because of this, the system clock
+ * rates should not be changed.
+ *
+ * The HCLK PLL is clocked from SYSCLK, which can be derived from the
+ * main oscillator or PLL397. PLL397 generates a rate that is 397 times
+ * the 32KHz oscillator rate. The main oscillator runs at the selected
+ * oscillator/crystal rate on the mosc_in pin of the LPC32xx. This rate
+ * is normally 13MHz, but depends on the selection of external crystals
+ * or oscillators. If USB operation is required, the main oscillator must
+ * be used in the system.
+ *
+ * Switching SYSCLK between sources during normal Linux operation is not
+ * supported. SYSCLK is preset in the bootloader. Because of the
+ * complexities of clock management during clock frequency changes,
+ * there are some limitations to the clock driver explained below:
+ * - The PLL397 and main oscillator can be enabled and disabled by the
+ * clk_enable() and clk_disable() functions unless SYSCLK is based
+ * on that clock. This allows the other oscillator that isn't driving
+ * the HCLK PLL to be used as another system clock that can be routed
+ * to an external pin.
+ * - The muxed SYSCLK input and HCLK_PLL rate cannot be changed with
+ * this driver.
+ * - HCLK and PCLK rates cannot be changed as part of this driver.
+ * - Most peripherals have their own dividers are part of the peripheral
+ * block. Changing SYSCLK, HCLK PLL, HCLK, or PCLK sources or rates
+ * will also impact the individual peripheral rates.
+ */
+
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/clcd.h>
+
+#include <mach/hardware.h>
+#include <asm/clkdev.h>
+#include <mach/clkdev.h>
+#include <mach/platform.h>
+#include "clock.h"
+#include "common.h"
+
+static struct clk clk_armpll;
+static struct clk clk_usbpll;
+static DEFINE_MUTEX(clkm_lock);
+
+/*
+ * Post divider values for PLLs based on selected register value
+ */
+static const u32 pll_postdivs[4] = {1, 2, 4, 8};
+
+static u32 local_return_parent_rate(struct clk *clk)
+{
+ /*
+ * If a clock has a rate of 0, then it inherits it's parent
+ * clock rate
+ */
+ if (clk->rate == 0)
+ return local_return_parent_rate(clk->parent);
+
+ return clk->rate;
+}
+
+/* 32KHz clock has a fixed rate and is not stoppable */
+static struct clk osc_32KHz = {
+ .rate = LPC32XX_CLOCK_OSC_FREQ,
+ .get_rate = local_return_parent_rate,
+};
+
+static int local_pll397_enable(struct clk *clk, int enable)
+{
+ u32 reg;
+ unsigned long timeout = 1 + msecs_to_jiffies(10);
+
+ reg = __raw_readl(LPC32XX_CLKPWR_PLL397_CTRL);
+
+ if (enable == 0) {
+ reg |= LPC32XX_CLKPWR_SYSCTRL_PLL397_DIS;
+ __raw_writel(reg, LPC32XX_CLKPWR_PLL397_CTRL);
+ } else {
+ /* Enable PLL397 */
+ reg &= ~LPC32XX_CLKPWR_SYSCTRL_PLL397_DIS;
+ __raw_writel(reg, LPC32XX_CLKPWR_PLL397_CTRL);
+
+ /* Wait for PLL397 lock */
+ while (((__raw_readl(LPC32XX_CLKPWR_PLL397_CTRL) &
+ LPC32XX_CLKPWR_SYSCTRL_PLL397_STS) == 0) &&
+ (timeout > jiffies))
+ cpu_relax();
+
+ if ((__raw_readl(LPC32XX_CLKPWR_PLL397_CTRL) &
+ LPC32XX_CLKPWR_SYSCTRL_PLL397_STS) == 0)
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int local_oscmain_enable(struct clk *clk, int enable)
+{
+ u32 reg;
+ unsigned long timeout = 1 + msecs_to_jiffies(10);
+
+ reg = __raw_readl(LPC32XX_CLKPWR_MAIN_OSC_CTRL);
+
+ if (enable == 0) {
+ reg |= LPC32XX_CLKPWR_MOSC_DISABLE;
+ __raw_writel(reg, LPC32XX_CLKPWR_MAIN_OSC_CTRL);
+ } else {
+ /* Enable main oscillator */
+ reg &= ~LPC32XX_CLKPWR_MOSC_DISABLE;
+ __raw_writel(reg, LPC32XX_CLKPWR_MAIN_OSC_CTRL);
+
+ /* Wait for main oscillator to start */
+ while (((__raw_readl(LPC32XX_CLKPWR_MAIN_OSC_CTRL) &
+ LPC32XX_CLKPWR_MOSC_DISABLE) != 0) &&
+ (timeout > jiffies))
+ cpu_relax();
+
+ if ((__raw_readl(LPC32XX_CLKPWR_MAIN_OSC_CTRL) &
+ LPC32XX_CLKPWR_MOSC_DISABLE) != 0)
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static struct clk osc_pll397 = {
+ .parent = &osc_32KHz,
+ .enable = local_pll397_enable,
+ .rate = LPC32XX_CLOCK_OSC_FREQ * 397,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk osc_main = {
+ .enable = local_oscmain_enable,
+ .rate = LPC32XX_MAIN_OSC_FREQ,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_sys;
+
+/*
+ * Convert a PLL register value to a PLL output frequency
+ */
+u32 clk_get_pllrate_from_reg(u32 inputclk, u32 regval)
+{
+ struct clk_pll_setup pllcfg;
+
+ pllcfg.cco_bypass_b15 = 0;
+ pllcfg.direct_output_b14 = 0;
+ pllcfg.fdbk_div_ctrl_b13 = 0;
+ if ((regval & LPC32XX_CLKPWR_HCLKPLL_CCO_BYPASS) != 0)
+ pllcfg.cco_bypass_b15 = 1;
+ if ((regval & LPC32XX_CLKPWR_HCLKPLL_POSTDIV_BYPASS) != 0)
+ pllcfg.direct_output_b14 = 1;
+ if ((regval & LPC32XX_CLKPWR_HCLKPLL_FDBK_SEL_FCLK) != 0)
+ pllcfg.fdbk_div_ctrl_b13 = 1;
+ pllcfg.pll_m = 1 + ((regval >> 1) & 0xFF);
+ pllcfg.pll_n = 1 + ((regval >> 9) & 0x3);
+ pllcfg.pll_p = pll_postdivs[((regval >> 11) & 0x3)];
+
+ return clk_check_pll_setup(inputclk, &pllcfg);
+}
+
+/*
+ * Setup the HCLK PLL with a PLL structure
+ */
+static u32 local_clk_pll_setup(struct clk_pll_setup *PllSetup)
+{
+ u32 tv, tmp = 0;
+
+ if (PllSetup->analog_on != 0)
+ tmp |= LPC32XX_CLKPWR_HCLKPLL_POWER_UP;
+ if (PllSetup->cco_bypass_b15 != 0)
+ tmp |= LPC32XX_CLKPWR_HCLKPLL_CCO_BYPASS;
+ if (PllSetup->direct_output_b14 != 0)
+ tmp |= LPC32XX_CLKPWR_HCLKPLL_POSTDIV_BYPASS;
+ if (PllSetup->fdbk_div_ctrl_b13 != 0)
+ tmp |= LPC32XX_CLKPWR_HCLKPLL_FDBK_SEL_FCLK;
+
+ tv = ffs(PllSetup->pll_p) - 1;
+ if ((!is_power_of_2(PllSetup->pll_p)) || (tv > 3))
+ return 0;
+
+ tmp |= LPC32XX_CLKPWR_HCLKPLL_POSTDIV_2POW(tv);
+ tmp |= LPC32XX_CLKPWR_HCLKPLL_PREDIV_PLUS1(PllSetup->pll_n - 1);
+ tmp |= LPC32XX_CLKPWR_HCLKPLL_PLLM(PllSetup->pll_m - 1);
+
+ return tmp;
+}
+
+/*
+ * Update the ARM core PLL frequency rate variable from the actual PLL setting
+ */
+static void local_update_armpll_rate(void)
+{
+ u32 clkin, pllreg;
+
+ clkin = clk_armpll.parent->rate;
+ pllreg = __raw_readl(LPC32XX_CLKPWR_HCLKPLL_CTRL) & 0x1FFFF;
+
+ clk_armpll.rate = clk_get_pllrate_from_reg(clkin, pllreg);
+}
+
+/*
+ * Find a PLL configuration for the selected input frequency
+ */
+static u32 local_clk_find_pll_cfg(u32 pllin_freq, u32 target_freq,
+ struct clk_pll_setup *pllsetup)
+{
+ u32 ifreq, freqtol, m, n, p, fclkout;
+
+ /* Determine frequency tolerance limits */
+ freqtol = target_freq / 250;
+ ifreq = pllin_freq;
+
+ /* Is direct bypass mode possible? */
+ if (abs(pllin_freq - target_freq) <= freqtol) {
+ pllsetup->analog_on = 0;
+ pllsetup->cco_bypass_b15 = 1;
+ pllsetup->direct_output_b14 = 1;
+ pllsetup->fdbk_div_ctrl_b13 = 1;
+ pllsetup->pll_p = pll_postdivs[0];
+ pllsetup->pll_n = 1;
+ pllsetup->pll_m = 1;
+ return clk_check_pll_setup(ifreq, pllsetup);
+ } else if (target_freq <= ifreq) {
+ pllsetup->analog_on = 0;
+ pllsetup->cco_bypass_b15 = 1;
+ pllsetup->direct_output_b14 = 0;
+ pllsetup->fdbk_div_ctrl_b13 = 1;
+ pllsetup->pll_n = 1;
+ pllsetup->pll_m = 1;
+ for (p = 0; p <= 3; p++) {
+ pllsetup->pll_p = pll_postdivs[p];
+ fclkout = clk_check_pll_setup(ifreq, pllsetup);
+ if (abs(target_freq - fclkout) <= freqtol)
+ return fclkout;
+ }
+ }
+
+ /* Is direct mode possible? */
+ pllsetup->analog_on = 1;
+ pllsetup->cco_bypass_b15 = 0;
+ pllsetup->direct_output_b14 = 1;
+ pllsetup->fdbk_div_ctrl_b13 = 0;
+ pllsetup->pll_p = pll_postdivs[0];
+ for (m = 1; m <= 256; m++) {
+ for (n = 1; n <= 4; n++) {
+ /* Compute output frequency for this value */
+ pllsetup->pll_n = n;
+ pllsetup->pll_m = m;
+ fclkout = clk_check_pll_setup(ifreq,
+ pllsetup);
+ if (abs(target_freq - fclkout) <=
+ freqtol)
+ return fclkout;
+ }
+ }
+
+ /* Is integer mode possible? */
+ pllsetup->analog_on = 1;
+ pllsetup->cco_bypass_b15 = 0;
+ pllsetup->direct_output_b14 = 0;
+ pllsetup->fdbk_div_ctrl_b13 = 1;
+ for (m = 1; m <= 256; m++) {
+ for (n = 1; n <= 4; n++) {
+ for (p = 0; p < 4; p++) {
+ /* Compute output frequency */
+ pllsetup->pll_p = pll_postdivs[p];
+ pllsetup->pll_n = n;
+ pllsetup->pll_m = m;
+ fclkout = clk_check_pll_setup(
+ ifreq, pllsetup);
+ if (abs(target_freq - fclkout) <= freqtol)
+ return fclkout;
+ }
+ }
+ }
+
+ /* Try non-integer mode */
+ pllsetup->analog_on = 1;
+ pllsetup->cco_bypass_b15 = 0;
+ pllsetup->direct_output_b14 = 0;
+ pllsetup->fdbk_div_ctrl_b13 = 0;
+ for (m = 1; m <= 256; m++) {
+ for (n = 1; n <= 4; n++) {
+ for (p = 0; p < 4; p++) {
+ /* Compute output frequency */
+ pllsetup->pll_p = pll_postdivs[p];
+ pllsetup->pll_n = n;
+ pllsetup->pll_m = m;
+ fclkout = clk_check_pll_setup(
+ ifreq, pllsetup);
+ if (abs(target_freq - fclkout) <= freqtol)
+ return fclkout;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static struct clk clk_armpll = {
+ .parent = &clk_sys,
+ .get_rate = local_return_parent_rate,
+};
+
+/*
+ * Update the USB PLL frequency rate variable from the actual PLL setting
+ */
+static void local_update_usbpll_rate(void)
+{
+ u32 clkin, pllreg;
+
+ clkin = clk_usbpll.get_rate(&clk_usbpll);
+ pllreg = __raw_readl(LPC32XX_CLKPWR_USB_CTRL) & 0x1FFFF;
+
+ if ((pllreg & LPC32XX_CLKPWR_USBCTRL_PLL_PWRUP) == 0)
+ clk_usbpll.rate = 0;
+ else
+ clk_usbpll.rate = clk_get_pllrate_from_reg(clkin,
+ pllreg);
+}
+
+/*
+ * Setup the USB PLL with a PLL structure
+ */
+static u32 local_clk_usbpll_setup(struct clk_pll_setup *pHCLKPllSetup)
+{
+ u32 reg, tmp = local_clk_pll_setup(pHCLKPllSetup);
+
+ reg = __raw_readl(LPC32XX_CLKPWR_USB_CTRL) & ~0x1FFFF;
+ reg |= tmp;
+ __raw_writel(reg, LPC32XX_CLKPWR_USB_CTRL);
+
+ return clk_check_pll_setup(clk_usbpll.parent->rate,
+ pHCLKPllSetup);
+}
+
+static int local_usbpll_enable(struct clk *clk, int enable)
+{
+ u32 reg;
+ int ret = -ENODEV;
+ unsigned long timeout = 1 + msecs_to_jiffies(10);
+
+ reg = __raw_readl(LPC32XX_CLKPWR_USB_CTRL);
+
+ if (enable == 0) {
+ reg &= ~(LPC32XX_CLKPWR_USBCTRL_CLK_EN1 |
+ LPC32XX_CLKPWR_USBCTRL_CLK_EN2);
+ __raw_writel(reg, LPC32XX_CLKPWR_USB_CTRL);
+ } else if (reg & LPC32XX_CLKPWR_USBCTRL_PLL_PWRUP) {
+ reg |= LPC32XX_CLKPWR_USBCTRL_CLK_EN1;
+ __raw_writel(reg, LPC32XX_CLKPWR_USB_CTRL);
+
+ /* Wait for PLL lock */
+ while ((timeout > jiffies) & (ret == -ENODEV)) {
+ reg = __raw_readl(LPC32XX_CLKPWR_USB_CTRL);
+ if (reg & LPC32XX_CLKPWR_USBCTRL_PLL_STS)
+ ret = 0;
+ }
+
+ if (ret == 0) {
+ reg |= LPC32XX_CLKPWR_USBCTRL_CLK_EN2;
+ __raw_writel(reg, LPC32XX_CLKPWR_USB_CTRL);
+ }
+ }
+
+ return ret;
+}
+
+static int local_usbpll_set_rate(struct clk *clk, u32 rate)
+{
+ u32 clkin, reg, usbdiv;
+ struct clk_pll_setup pllsetup;
+
+ /*
+ * Unlike other clocks, this clock has a KHz input rate, so bump
+ * it up to work with the PLL function
+ */
+ rate = rate * 1000;
+
+ local_usbpll_enable(clk, 0);
+
+ if (rate == 0)
+ return 0;
+
+ clkin = clk->parent->rate;
+ usbdiv = (__raw_readl(LPC32XX_CLKPWR_USBCLK_PDIV) &
+ LPC32XX_CLKPWR_USBPDIV_PLL_MASK) + 1;
+ clkin = clkin / usbdiv;
+
+ /* Try to find a good rate setup */
+ if (local_clk_find_pll_cfg(clkin, rate, &pllsetup) == 0)
+ return -EINVAL;
+
+ reg = __raw_readl(LPC32XX_CLKPWR_USB_CTRL);
+ reg |= LPC32XX_CLKPWR_USBCTRL_CLK_EN1;
+ __raw_writel(reg, LPC32XX_CLKPWR_USB_CTRL);
+
+ pllsetup.analog_on = 1;
+ local_clk_usbpll_setup(&pllsetup);
+
+ clk->rate = clk_check_pll_setup(clkin, &pllsetup);
+
+ reg = __raw_readl(LPC32XX_CLKPWR_USB_CTRL);
+ reg |= LPC32XX_CLKPWR_USBCTRL_CLK_EN2;
+ __raw_writel(reg, LPC32XX_CLKPWR_USB_CTRL);
+
+ return 0;
+}
+
+static struct clk clk_usbpll = {
+ .parent = &osc_main,
+ .set_rate = local_usbpll_set_rate,
+ .enable = local_usbpll_enable,
+ .get_rate = local_return_parent_rate,
+};
+
+static u32 clk_get_hclk_div(void)
+{
+ static const u32 hclkdivs[4] = {1, 2, 4, 4};
+ return hclkdivs[LPC32XX_CLKPWR_HCLKDIV_DIV_2POW(
+ __raw_readl(LPC32XX_CLKPWR_HCLK_DIV))];
+}
+
+static struct clk clk_hclk = {
+ .parent = &clk_armpll,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_pclk = {
+ .parent = &clk_armpll,
+ .get_rate = local_return_parent_rate,
+};
+
+static int local_onoff_enable(struct clk *clk, int enable)
+{
+ u32 tmp;
+
+ tmp = __raw_readl(clk->enable_reg);
+
+ if (enable == 0)
+ tmp &= ~clk->enable_mask;
+ else
+ tmp |= clk->enable_mask;
+
+ __raw_writel(tmp, clk->enable_reg);
+
+ return 0;
+}
+
+/* Peripheral clock sources */
+static struct clk clk_timer0 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_TIMERS_PWMS_CLK_CTRL_1,
+ .enable_mask = LPC32XX_CLKPWR_TMRPWMCLK_TIMER0_EN,
+ .get_rate = local_return_parent_rate,
+};
+static struct clk clk_timer1 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_TIMERS_PWMS_CLK_CTRL_1,
+ .enable_mask = LPC32XX_CLKPWR_TMRPWMCLK_TIMER1_EN,
+ .get_rate = local_return_parent_rate,
+};
+static struct clk clk_timer2 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_TIMERS_PWMS_CLK_CTRL_1,
+ .enable_mask = LPC32XX_CLKPWR_TMRPWMCLK_TIMER2_EN,
+ .get_rate = local_return_parent_rate,
+};
+static struct clk clk_timer3 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_TIMERS_PWMS_CLK_CTRL_1,
+ .enable_mask = LPC32XX_CLKPWR_TMRPWMCLK_TIMER3_EN,
+ .get_rate = local_return_parent_rate,
+};
+static struct clk clk_wdt = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_TIMER_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_PWMCLK_WDOG_EN,
+ .get_rate = local_return_parent_rate,
+};
+static struct clk clk_vfp9 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_DEBUG_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_VFP_CLOCK_ENABLE_BIT,
+ .get_rate = local_return_parent_rate,
+};
+static struct clk clk_dma = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_DMA_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_uart3 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_UART_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_UARTCLKCTRL_UART3_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_uart4 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_UART_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_UARTCLKCTRL_UART4_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_uart5 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_UART_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_UARTCLKCTRL_UART5_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_uart6 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_UART_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_UARTCLKCTRL_UART6_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_i2c0 = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_I2C_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_I2CCLK_I2C1CLK_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_i2c1 = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_I2C_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_I2CCLK_I2C2CLK_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_i2c2 = {
+ .parent = &clk_pclk,
+ .enable = local_onoff_enable,
+ .enable_reg = io_p2v(LPC32XX_USB_BASE + 0xFF4),
+ .enable_mask = 0x4,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_ssp0 = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_SSP_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_ssp1 = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_SSP_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_SSPCTRL_SSPCLK1_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_kscan = {
+ .parent = &osc_32KHz,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_KEY_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_KEYCLKCTRL_CLK_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_nand = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_NAND_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_i2s0 = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_I2S_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_I2SCTRL_I2SCLK0_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_i2s1 = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_I2S_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_net = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_MACCLK_CTRL,
+ .enable_mask = (LPC32XX_CLKPWR_MACCTRL_DMACLK_EN |
+ LPC32XX_CLKPWR_MACCTRL_MMIOCLK_EN |
+ LPC32XX_CLKPWR_MACCTRL_HRCCLK_EN),
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_rtc = {
+ .parent = &osc_32KHz,
+ .rate = 1, /* 1 Hz */
+ .get_rate = local_return_parent_rate,
+};
+
+static struct clk clk_usbd = {
+ .parent = &clk_usbpll,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_USB_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_USBCTRL_HCLK_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static int tsc_onoff_enable(struct clk *clk, int enable)
+{
+ u32 tmp;
+
+ /* Make sure 32KHz clock is the selected clock */
+ tmp = __raw_readl(LPC32XX_CLKPWR_ADC_CLK_CTRL_1);
+ tmp &= ~LPC32XX_CLKPWR_ADCCTRL1_PCLK_SEL;
+ __raw_writel(tmp, LPC32XX_CLKPWR_ADC_CLK_CTRL_1);
+
+ if (enable == 0)
+ __raw_writel(0, clk->enable_reg);
+ else
+ __raw_writel(clk->enable_mask, clk->enable_reg);
+
+ return 0;
+}
+
+static struct clk clk_tsc = {
+ .parent = &osc_32KHz,
+ .enable = tsc_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_ADC_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_ADC32CLKCTRL_CLK_EN,
+ .get_rate = local_return_parent_rate,
+};
+
+static int mmc_onoff_enable(struct clk *clk, int enable)
+{
+ u32 tmp;
+
+ tmp = __raw_readl(LPC32XX_CLKPWR_MS_CTRL) &
+ ~(LPC32XX_CLKPWR_MSCARD_SDCARD_EN |
+ LPC32XX_CLKPWR_MSCARD_SDCARD_DIV(15));
+
+ /* If rate is 0, disable clock */
+ if (enable != 0)
+ tmp |= LPC32XX_CLKPWR_MSCARD_SDCARD_EN |
+ LPC32XX_CLKPWR_MSCARD_SDCARD_DIV(1);
+
+ __raw_writel(tmp, LPC32XX_CLKPWR_MS_CTRL);
+
+ return 0;
+}
+
+static u32 mmc_get_rate(struct clk *clk)
+{
+ u32 div, tmp, rate;
+
+ div = __raw_readl(LPC32XX_CLKPWR_MS_CTRL);
+ tmp = div & LPC32XX_CLKPWR_MSCARD_SDCARD_EN;
+
+ if (!tmp)
+ return 0;
+
+ /* Get the parent clock rate */
+ rate = clk->parent->get_rate(clk->parent);
+
+ /* Get the LCD controller clock divider value */
+ div = div & 0xF;
+
+ if (!div)
+ return 0;
+
+ tmp = rate / div;
+
+ return tmp;
+}
+
+static int mmc_set_rate(struct clk *clk, u32 rate)
+{
+ if (rate == 0)
+ mmc_onoff_enable(clk, 0);
+ else
+ mmc_onoff_enable(clk, 1);
+
+ return 0;
+}
+
+static struct clk clk_mmc = {
+ .parent = &clk_armpll,
+ .set_rate = mmc_set_rate,
+ .get_rate = mmc_get_rate,
+ .enable = mmc_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_MS_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_MSCARD_SDCARD_EN,
+};
+
+static u32 clcd_get_rate(struct clk *clk)
+{
+ u32 tmp, div, rate;
+
+ tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) &
+ LPC32XX_CLKPWR_LCDCTRL_CLK_EN;
+
+ if (!tmp)
+ return 0;
+
+ rate = clk->parent->get_rate(clk->parent);
+ tmp = __raw_readl(io_p2v(LPC32XX_LCD_BASE + CLCD_TIM2));
+
+ /* Only supports internal clocking */
+ if (tmp & TIM2_BCD)
+ return rate;
+
+ div = (tmp & 0x1F) | ((tmp & 0xF8) >> 22);
+ tmp = rate / (2 + div);
+
+ return tmp;
+}
+
+static int clcd_set_rate(struct clk *clk, u32 rate)
+{
+ u32 tmp, prate, div;
+
+ tmp = __raw_readl(io_p2v(LPC32XX_LCD_BASE + CLCD_TIM2));
+ prate = clk->parent->get_rate(clk->parent);
+
+ if (rate == prate) {
+ tmp |= TIM2_BCD;
+ local_onoff_enable(clk, 1);
+ } else {
+ /* Find closest divider */
+ div = prate / rate;
+ if (div == 1)
+ div = 0;
+ else
+ div -= 2;
+
+ tmp &= ~(0xF800001F);
+ tmp &= ~TIM2_BCD;
+ tmp |= (div & 0x1F);
+ tmp |= (((div >> 5) & 0x1F) << 27);
+ __raw_writel(tmp, io_p2v(LPC32XX_LCD_BASE + CLCD_TIM2));
+ local_onoff_enable(clk, 1);
+ }
+
+ return 0;
+}
+
+static struct clk clk_lcd = {
+ .parent = &clk_hclk,
+ .set_rate = clcd_set_rate,
+ .get_rate = clcd_get_rate,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_LCDCLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_LCDCTRL_CLK_EN,
+};
+
+static inline void clk_lock(void)
+{
+ mutex_lock(&clkm_lock);
+}
+
+static inline void clk_unlock(void)
+{
+ mutex_unlock(&clkm_lock);
+}
+
+static void local_clk_disable(struct clk *clk)
+{
+ WARN_ON(clk->usecount == 0);
+
+ /* Don't attempt to disable clock if it has no users */
+ if (clk->usecount > 0) {
+ clk->usecount--;
+
+ /* Only disable clock when it has no more users */
+ if ((clk->usecount == 0) && (clk->enable))
+ clk->enable(clk, 0);
+
+ /* Check parent clocks, they may need to be disabled too */
+ if (clk->parent)
+ local_clk_disable(clk->parent);
+ }
+}
+
+static int local_clk_enable(struct clk *clk)
+{
+ int ret = 0;
+
+ /* Only enable clock if it's currently disabled */
+ if (clk->usecount == 0) {
+ if (clk->enable)
+ ret = clk->enable(clk, 1);
+ }
+
+ /* Enable parent clock and update counts */
+ if (!ret) {
+ clk->usecount++;
+
+ if (clk->parent) {
+ ret = local_clk_enable(clk->parent);
+
+ if (ret) {
+ clk->usecount--;
+ if ((!clk->usecount) && (clk->enable))
+ clk->enable(clk, 0);
+ }
+ }
+ }
+
+ return ret;
+}
+
+/*
+ * clk_enable - inform the system when the clock source should be running.
+ */
+int clk_enable(struct clk *clk)
+{
+ int ret;
+
+ clk_lock();
+ ret = local_clk_enable(clk);
+ clk_unlock();
+
+ return ret;
+}
+EXPORT_SYMBOL(clk_enable);
+
+/*
+ * clk_disable - inform the system when the clock source is no longer required
+ */
+void clk_disable(struct clk *clk)
+{
+ clk_lock();
+ local_clk_disable(clk);
+ clk_unlock();
+}
+EXPORT_SYMBOL(clk_disable);
+
+/*
+ * clk_get_rate - obtain the current clock rate (in Hz) for a clock source
+ */
+unsigned long clk_get_rate(struct clk *clk)
+{
+ unsigned long rate;
+
+ clk_lock();
+ rate = (clk->get_rate)(clk);
+ clk_unlock();
+
+ return rate;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+/*
+ * clk_set_rate - set the clock rate for a clock source
+ */
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ int ret = -EINVAL;
+
+ /*
+ * Most system clocks can only be enabled or disabled, with
+ * the actual rate set as part of the peripheral dividers
+ * instead of high level clock control
+ */
+ if (clk->set_rate) {
+ clk_lock();
+ ret = (clk->set_rate)(clk, rate);
+ clk_unlock();
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL(clk_set_rate);
+
+/*
+ * clk_round_rate - adjust a rate to the exact rate a clock can provide
+ */
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ int ret;
+
+ /* Use set_rate to try to adjust the rate if it supports it */
+ ret = clk_set_rate(clk, rate);
+ if (ret < 0)
+ return ret;
+
+ return clk->rate;
+}
+EXPORT_SYMBOL(clk_round_rate);
+
+/*
+ * clk_set_parent - set the parent clock source for this clock
+ */
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+ /* Clock re-parenting is not supported */
+ return -EINVAL;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
+/*
+ * clk_get_parent - get the parent clock source for this clock
+ */
+struct clk *clk_get_parent(struct clk *clk)
+{
+ return clk->parent;
+}
+EXPORT_SYMBOL(clk_get_parent);
+
+#define _REGISTER_CLOCK(d, n, c) \
+ { \
+ .dev_id = (d), \
+ .con_id = (n), \
+ .clk = &(c), \
+ },
+
+static struct clk_lookup lookups[] = {
+ _REGISTER_CLOCK(NULL, "osc_32KHz", osc_32KHz)
+ _REGISTER_CLOCK(NULL, "osc_pll397", osc_pll397)
+ _REGISTER_CLOCK(NULL, "osc_main", osc_main)
+ _REGISTER_CLOCK(NULL, "sys_ck", clk_sys)
+ _REGISTER_CLOCK(NULL, "arm_pll_ck", clk_armpll)
+ _REGISTER_CLOCK(NULL, "ck_pll5", clk_usbpll)
+ _REGISTER_CLOCK(NULL, "hclk_ck", clk_hclk)
+ _REGISTER_CLOCK(NULL, "pclk_ck", clk_pclk)
+ _REGISTER_CLOCK(NULL, "timer0_ck", clk_timer0)
+ _REGISTER_CLOCK(NULL, "timer1_ck", clk_timer1)
+ _REGISTER_CLOCK(NULL, "timer2_ck", clk_timer2)
+ _REGISTER_CLOCK(NULL, "timer3_ck", clk_timer3)
+ _REGISTER_CLOCK(NULL, "vfp9_ck", clk_vfp9)
+ _REGISTER_CLOCK(NULL, "clk_dmac", clk_dma)
+ _REGISTER_CLOCK("pnx4008-watchdog", NULL, clk_wdt)
+ _REGISTER_CLOCK(NULL, "uart3_ck", clk_uart3)
+ _REGISTER_CLOCK(NULL, "uart4_ck", clk_uart4)
+ _REGISTER_CLOCK(NULL, "uart5_ck", clk_uart5)
+ _REGISTER_CLOCK(NULL, "uart6_ck", clk_uart6)
+ _REGISTER_CLOCK("pnx-i2c.0", NULL, clk_i2c0)
+ _REGISTER_CLOCK("pnx-i2c.1", NULL, clk_i2c1)
+ _REGISTER_CLOCK("pnx-i2c.2", NULL, clk_i2c2)
+ _REGISTER_CLOCK("dev:ssp0", NULL, clk_ssp0)
+ _REGISTER_CLOCK("dev:ssp1", NULL, clk_ssp1)
+ _REGISTER_CLOCK("lpc32xx_keys.0", NULL, clk_kscan)
+ _REGISTER_CLOCK("lpc32xx-nand.0", "nand_ck", clk_nand)
+ _REGISTER_CLOCK("tbd", "i2s0_ck", clk_i2s0)
+ _REGISTER_CLOCK("tbd", "i2s1_ck", clk_i2s1)
+ _REGISTER_CLOCK("lpc32xx-ts", NULL, clk_tsc)
+ _REGISTER_CLOCK("dev:mmc0", "MCLK", clk_mmc)
+ _REGISTER_CLOCK("lpc-net.0", NULL, clk_net)
+ _REGISTER_CLOCK("dev:clcd", NULL, clk_lcd)
+ _REGISTER_CLOCK("lpc32xx_udc", "ck_usbd", clk_usbd)
+ _REGISTER_CLOCK("lpc32xx_rtc", NULL, clk_rtc)
+};
+
+static int __init clk_init(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(lookups); i++)
+ clkdev_add(&lookups[i]);
+
+ /*
+ * Setup muxed SYSCLK for HCLK PLL base -this selects the
+ * parent clock used for the ARM PLL and is used to derive
+ * the many system clock rates in the device.
+ */
+ if (clk_is_sysclk_mainosc() != 0)
+ clk_sys.parent = &osc_main;
+ else
+ clk_sys.parent = &osc_pll397;
+
+ clk_sys.rate = clk_sys.parent->rate;
+
+ /* Compute the current ARM PLL and USB PLL frequencies */
+ local_update_armpll_rate();
+ local_update_usbpll_rate();
+
+ /* Compute HCLK and PCLK bus rates */
+ clk_hclk.rate = clk_hclk.parent->rate / clk_get_hclk_div();
+ clk_pclk.rate = clk_pclk.parent->rate / clk_get_pclk_div();
+
+ /*
+ * Enable system clocks - this step is somewhat formal, as the
+ * clocks are already running, but it does get the clock data
+ * inline with the actual system state. Never disable these
+ * clocks as they will only stop if the system is going to sleep.
+ * In that case, the chip/system power management functions will
+ * handle clock gating.
+ */
+ clk_enable(&clk_hclk);
+ clk_enable(&clk_pclk);
+
+ /*
+ * Timers 0 and 1 were enabled and are being used by the high
+ * resolution tick function prior to this driver being initialized.
+ * Tag them now as used.
+ */
+ clk_enable(&clk_timer0);
+ clk_enable(&clk_timer1);
+
+ return 0;
+}
+core_initcall(clk_init);
+
diff --git a/arch/arm/mach-lpc32xx/clock.h b/arch/arm/mach-lpc32xx/clock.h
new file mode 100644
index 0000000..3918be3
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/clock.h
@@ -0,0 +1,37 @@
+/*
+ * arch/arm/mach-lpc32xx/clock.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __LPC32XX_CLOCK_H
+#define __LPC32XX_CLOCK_H
+
+struct clk {
+ struct list_head node;
+ struct clk *parent;
+ u32 rate;
+ u32 usecount;
+
+ int (*set_rate) (struct clk *, u32);
+ int (*enable) (struct clk *clk, int);
+ u32 (*get_rate) (struct clk *clk);
+
+ /* Register address and bit mask for simple clocks */
+ void __iomem *enable_reg;
+ u32 enable_mask;
+};
+
+#endif
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 04/13] ARM: LPC32XX: GPIO, timer, and IRQ drivers
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (2 preceding siblings ...)
2010-02-19 23:25 ` [PATCH 03/13] ARM: LPC32XX: Clock driver wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 05/13] ARM: LPC32XX: System suspend support wellsk40 at gmail.com
` (8 subsequent siblings)
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Common drivers for the LPC32XX used on all platforms
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/gpiolib.c | 446 +++++++++++++++++++++++++++++++++++++++
arch/arm/mach-lpc32xx/irq.c | 434 +++++++++++++++++++++++++++++++++++++
arch/arm/mach-lpc32xx/timer.c | 182 ++++++++++++++++
3 files changed, 1062 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/gpiolib.c b/arch/arm/mach-lpc32xx/gpiolib.c
new file mode 100644
index 0000000..e9d816c
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/gpiolib.c
@@ -0,0 +1,446 @@
+/*
+ * arch/arm/mach-lpc32xx/gpiolib.c
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/errno.h>
+#include <linux/gpio.h>
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+#include "common.h"
+
+#define LPC32XX_GPIO_P3_INP_STATE _GPREG(0x000)
+#define LPC32XX_GPIO_P3_OUTP_SET _GPREG(0x004)
+#define LPC32XX_GPIO_P3_OUTP_CLR _GPREG(0x008)
+#define LPC32XX_GPIO_P3_OUTP_STATE _GPREG(0x00C)
+#define LPC32XX_GPIO_P2_DIR_SET _GPREG(0x010)
+#define LPC32XX_GPIO_P2_DIR_CLR _GPREG(0x014)
+#define LPC32XX_GPIO_P2_DIR_STATE _GPREG(0x018)
+#define LPC32XX_GPIO_P2_INP_STATE _GPREG(0x01C)
+#define LPC32XX_GPIO_P2_OUTP_SET _GPREG(0x020)
+#define LPC32XX_GPIO_P2_OUTP_CLR _GPREG(0x024)
+#define LPC32XX_GPIO_P2_MUX_SET _GPREG(0x028)
+#define LPC32XX_GPIO_P2_MUX_CLR _GPREG(0x02C)
+#define LPC32XX_GPIO_P2_MUX_STATE _GPREG(0x030)
+#define LPC32XX_GPIO_P0_INP_STATE _GPREG(0x040)
+#define LPC32XX_GPIO_P0_OUTP_SET _GPREG(0x044)
+#define LPC32XX_GPIO_P0_OUTP_CLR _GPREG(0x048)
+#define LPC32XX_GPIO_P0_OUTP_STATE _GPREG(0x04C)
+#define LPC32XX_GPIO_P0_DIR_SET _GPREG(0x050)
+#define LPC32XX_GPIO_P0_DIR_CLR _GPREG(0x054)
+#define LPC32XX_GPIO_P0_DIR_STATE _GPREG(0x058)
+#define LPC32XX_GPIO_P1_INP_STATE _GPREG(0x060)
+#define LPC32XX_GPIO_P1_OUTP_SET _GPREG(0x064)
+#define LPC32XX_GPIO_P1_OUTP_CLR _GPREG(0x068)
+#define LPC32XX_GPIO_P1_OUTP_STATE _GPREG(0x06C)
+#define LPC32XX_GPIO_P1_DIR_SET _GPREG(0x070)
+#define LPC32XX_GPIO_P1_DIR_CLR _GPREG(0x074)
+#define LPC32XX_GPIO_P1_DIR_STATE _GPREG(0x078)
+
+#define GPIO012_PIN_TO_BIT(x) (1 << (x))
+#define GPIO3_PIN_TO_BIT(x) (1 << ((x) + 25))
+#define GPO3_PIN_TO_BIT(x) (1 << (x))
+#define GPIO012_PIN_IN_SEL(x, y) (((x) >> (y)) & 1)
+#define GPIO3_PIN_IN_SHIFT(x) ((x) == 5 ? 24 : 10 + (x))
+#define GPIO3_PIN_IN_SEL(x, y) ((x) >> GPIO3_PIN_IN_SHIFT(y))
+#define GPIO3_PIN5_IN_SEL(x) (((x) >> 24) & 1)
+#define GPI3_PIN_IN_SEL(x, y) (((x) >> (y)) & 1)
+
+struct gpio_regs {
+ void __iomem *inp_state;
+ void __iomem *outp_set;
+ void __iomem *outp_clr;
+ void __iomem *dir_set;
+ void __iomem *dir_clr;
+};
+
+/*
+ * GPIO names
+ */
+static const char *gpio_p0_names[LPC32XX_GPIO_P0_MAX] = {
+ "p0.0", "p0.1", "p0.2", "p0.3",
+ "p0.4", "p0.5", "p0.6", "p0.7"
+};
+
+static const char *gpio_p1_names[LPC32XX_GPIO_P1_MAX] = {
+ "p1.0", "p1.1", "p1.2", "p1.3",
+ "p1.4", "p1.5", "p1.6", "p1.7",
+ "p1.8", "p1.9", "p1.10", "p1.11",
+ "p1.12", "p1.13", "p1.14", "p1.15",
+ "p1.16", "p1.17", "p1.18", "p1.19",
+ "p1.20", "p1.21", "p1.22", "p1.23",
+};
+
+static const char *gpio_p2_names[LPC32XX_GPIO_P2_MAX] = {
+ "p2.0", "p2.1", "p2.2", "p2.3",
+ "p2.4", "p2.5", "p2.6", "p2.7",
+ "p2.8", "p2.9", "p2.10", "p2.11",
+ "p2.12"
+};
+
+static const char *gpio_p3_names[LPC32XX_GPIO_P3_MAX] = {
+ "gpi000", "gpio01", "gpio02", "gpio03",
+ "gpio04", "gpio05"
+};
+
+static const char *gpi_p3_names[LPC32XX_GPI_P3_MAX] = {
+ "gpi00", "gpi01", "gpi02", "gpi03",
+ "gpi04", "gpi05", "gpi06", "gpi07",
+ "gpi08", "gpi09", NULL, NULL,
+ NULL, NULL, NULL, "gpi15",
+ "gpi16", "gpi17", "gpi18", "gpi19",
+ "gpi20", "gpi21", "gpi22", "gpi23",
+ "gpi24", "gpi25", "gpi26", "gpi27"
+};
+
+static const char *gpo_p3_names[LPC32XX_GPO_P3_MAX] = {
+ "gpo00", "gpo01", "gpo02", "gpo03",
+ "gpo04", "gpo05", "gpo06", "gpo07",
+ "gpo08", "gpo09", "gpo10", "gpo11",
+ "gpo12", "gpo13", "gpo14", "gpo15",
+ "gpo16", "gpo17", "gpo18", "gpo19",
+ "gpo20", "gpo21", "gpo22", "gpo23"
+};
+
+static struct gpio_regs gpio_grp_regs_p0 = {
+ .inp_state = LPC32XX_GPIO_P0_INP_STATE,
+ .outp_set = LPC32XX_GPIO_P0_OUTP_SET,
+ .outp_clr = LPC32XX_GPIO_P0_OUTP_CLR,
+ .dir_set = LPC32XX_GPIO_P0_DIR_SET,
+ .dir_clr = LPC32XX_GPIO_P0_DIR_CLR,
+};
+
+static struct gpio_regs gpio_grp_regs_p1 = {
+ .inp_state = LPC32XX_GPIO_P1_INP_STATE,
+ .outp_set = LPC32XX_GPIO_P1_OUTP_SET,
+ .outp_clr = LPC32XX_GPIO_P1_OUTP_CLR,
+ .dir_set = LPC32XX_GPIO_P1_DIR_SET,
+ .dir_clr = LPC32XX_GPIO_P1_DIR_CLR,
+};
+
+static struct gpio_regs gpio_grp_regs_p2 = {
+ .inp_state = LPC32XX_GPIO_P2_INP_STATE,
+ .outp_set = LPC32XX_GPIO_P2_OUTP_SET,
+ .outp_clr = LPC32XX_GPIO_P2_OUTP_CLR,
+ .dir_set = LPC32XX_GPIO_P2_DIR_SET,
+ .dir_clr = LPC32XX_GPIO_P2_DIR_CLR,
+};
+
+static struct gpio_regs gpio_grp_regs_p3 = {
+ .inp_state = LPC32XX_GPIO_P3_INP_STATE,
+ .outp_set = LPC32XX_GPIO_P3_OUTP_SET,
+ .outp_clr = LPC32XX_GPIO_P3_OUTP_CLR,
+ .dir_set = LPC32XX_GPIO_P2_DIR_SET,
+ .dir_clr = LPC32XX_GPIO_P2_DIR_CLR,
+};
+
+struct lpc32xx_gpio_chip {
+ struct gpio_chip chip;
+ struct gpio_regs *gpio_grp;
+};
+
+static inline struct lpc32xx_gpio_chip *to_lpc32xx_gpio(
+ struct gpio_chip *gpc)
+{
+ return container_of(gpc, struct lpc32xx_gpio_chip, chip);
+}
+
+static void __set_gpio_dir_p012(struct lpc32xx_gpio_chip *group,
+ unsigned pin, int input)
+{
+ if (input)
+ __raw_writel(GPIO012_PIN_TO_BIT(pin),
+ group->gpio_grp->dir_clr);
+ else
+ __raw_writel(GPIO012_PIN_TO_BIT(pin),
+ group->gpio_grp->dir_set);
+}
+
+static void __set_gpio_dir_p3(struct lpc32xx_gpio_chip *group,
+ unsigned pin, int input)
+{
+ u32 u = GPIO3_PIN_TO_BIT(pin);
+
+ if (input)
+ __raw_writel(u, group->gpio_grp->dir_clr);
+ else
+ __raw_writel(u, group->gpio_grp->dir_set);
+}
+
+static void __set_gpio_level_p012(struct lpc32xx_gpio_chip *group,
+ unsigned pin, int high)
+{
+ if (high)
+ __raw_writel(GPIO012_PIN_TO_BIT(pin),
+ group->gpio_grp->outp_set);
+ else
+ __raw_writel(GPIO012_PIN_TO_BIT(pin),
+ group->gpio_grp->outp_clr);
+}
+
+static void __set_gpio_level_p3(struct lpc32xx_gpio_chip *group,
+ unsigned pin, int high)
+{
+ u32 u = GPIO3_PIN_TO_BIT(pin);
+
+ if (high)
+ __raw_writel(u, group->gpio_grp->outp_set);
+ else
+ __raw_writel(u, group->gpio_grp->outp_clr);
+}
+
+static void __set_gpo_level_p3(struct lpc32xx_gpio_chip *group,
+ unsigned pin, int high)
+{
+ if (high)
+ __raw_writel(GPO3_PIN_TO_BIT(pin), group->gpio_grp->outp_set);
+ else
+ __raw_writel(GPO3_PIN_TO_BIT(pin), group->gpio_grp->outp_clr);
+}
+
+static int __get_gpio_state_p012(struct lpc32xx_gpio_chip *group,
+ unsigned pin)
+{
+ return GPIO012_PIN_IN_SEL(__raw_readl(group->gpio_grp->inp_state),
+ pin);
+}
+
+static int __get_gpio_state_p3(struct lpc32xx_gpio_chip *group,
+ unsigned pin)
+{
+ int state = __raw_readl(group->gpio_grp->inp_state);
+
+ /*
+ * P3 GPIO pin input mapping is not contiguous, GPIOP3-0..4 is mapped
+ * to bits 10..14, while GPIOP3-5 is mapped to bit 24.
+ */
+ return GPIO3_PIN_IN_SEL(state, pin);
+}
+
+static int __get_gpi_state_p3(struct lpc32xx_gpio_chip *group,
+ unsigned pin)
+{
+ return GPI3_PIN_IN_SEL(__raw_readl(group->gpio_grp->inp_state), pin);
+}
+
+/*
+ * GENERIC_GPIO primitives.
+ */
+static int lpc32xx_gpio_dir_input_p012(struct gpio_chip *chip,
+ unsigned pin)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ __set_gpio_dir_p012(group, pin, 1);
+
+ return 0;
+}
+
+static int lpc32xx_gpio_dir_input_p3(struct gpio_chip *chip,
+ unsigned pin)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ __set_gpio_dir_p3(group, pin, 1);
+
+ return 0;
+}
+
+static int lpc32xx_gpio_dir_in_always(struct gpio_chip *chip,
+ unsigned pin)
+{
+ return 0;
+}
+
+static int lpc32xx_gpio_get_value_p012(struct gpio_chip *chip, unsigned pin)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ return __get_gpio_state_p012(group, pin);
+}
+
+static int lpc32xx_gpio_get_value_p3(struct gpio_chip *chip, unsigned pin)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ return __get_gpio_state_p3(group, pin);
+}
+
+static int lpc32xx_gpi_get_value(struct gpio_chip *chip, unsigned pin)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ return __get_gpi_state_p3(group, pin);
+}
+
+static int lpc32xx_gpio_dir_output_p012(struct gpio_chip *chip, unsigned pin,
+ int value)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ __set_gpio_dir_p012(group, pin, 0);
+
+ return 0;
+}
+
+static int lpc32xx_gpio_dir_output_p3(struct gpio_chip *chip, unsigned pin,
+ int value)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ __set_gpio_dir_p3(group, pin, 0);
+
+ return 0;
+}
+
+static int lpc32xx_gpio_dir_out_always(struct gpio_chip *chip, unsigned pin,
+ int value)
+{
+ return 0;
+}
+
+static void lpc32xx_gpio_set_value_p012(struct gpio_chip *chip, unsigned pin,
+ int value)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ __set_gpio_level_p012(group, pin, value);
+}
+
+static void lpc32xx_gpio_set_value_p3(struct gpio_chip *chip, unsigned pin,
+ int value)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ __set_gpio_level_p3(group, pin, value);
+}
+
+static void lpc32xx_gpo_set_value(struct gpio_chip *chip, unsigned pin,
+ int value)
+{
+ struct lpc32xx_gpio_chip *group = to_lpc32xx_gpio(chip);
+
+ __set_gpo_level_p3(group, pin, value);
+}
+
+static int lpc32xx_gpio_request(struct gpio_chip *chip, unsigned pin)
+{
+ if (pin < chip->ngpio)
+ return 0;
+
+ return -EINVAL;
+}
+
+static struct lpc32xx_gpio_chip lpc32xx_gpiochip[] = {
+ {
+ .chip = {
+ .label = "gpio_p0",
+ .direction_input = lpc32xx_gpio_dir_input_p012,
+ .get = lpc32xx_gpio_get_value_p012,
+ .direction_output = lpc32xx_gpio_dir_output_p012,
+ .set = lpc32xx_gpio_set_value_p012,
+ .request = lpc32xx_gpio_request,
+ .base = LPC32XX_GPIO_P0_GRP,
+ .ngpio = LPC32XX_GPIO_P0_MAX,
+ .names = gpio_p0_names,
+ .can_sleep = 0,
+ },
+ .gpio_grp = &gpio_grp_regs_p0,
+ },
+ {
+ .chip = {
+ .label = "gpio_p1",
+ .direction_input = lpc32xx_gpio_dir_input_p012,
+ .get = lpc32xx_gpio_get_value_p012,
+ .direction_output = lpc32xx_gpio_dir_output_p012,
+ .set = lpc32xx_gpio_set_value_p012,
+ .request = lpc32xx_gpio_request,
+ .base = LPC32XX_GPIO_P1_GRP,
+ .ngpio = LPC32XX_GPIO_P1_MAX,
+ .names = gpio_p1_names,
+ .can_sleep = 0,
+ },
+ .gpio_grp = &gpio_grp_regs_p1,
+ },
+ {
+ .chip = {
+ .label = "gpio_p2",
+ .direction_input = lpc32xx_gpio_dir_input_p012,
+ .get = lpc32xx_gpio_get_value_p012,
+ .direction_output = lpc32xx_gpio_dir_output_p012,
+ .set = lpc32xx_gpio_set_value_p012,
+ .request = lpc32xx_gpio_request,
+ .base = LPC32XX_GPIO_P2_GRP,
+ .ngpio = LPC32XX_GPIO_P2_MAX,
+ .names = gpio_p2_names,
+ .can_sleep = 0,
+ },
+ .gpio_grp = &gpio_grp_regs_p2,
+ },
+ {
+ .chip = {
+ .label = "gpio_p3",
+ .direction_input = lpc32xx_gpio_dir_input_p3,
+ .get = lpc32xx_gpio_get_value_p3,
+ .direction_output = lpc32xx_gpio_dir_output_p3,
+ .set = lpc32xx_gpio_set_value_p3,
+ .request = lpc32xx_gpio_request,
+ .base = LPC32XX_GPIO_P3_GRP,
+ .ngpio = LPC32XX_GPIO_P3_MAX,
+ .names = gpio_p3_names,
+ .can_sleep = 0,
+ },
+ .gpio_grp = &gpio_grp_regs_p3,
+ },
+ {
+ .chip = {
+ .label = "gpi_p3",
+ .direction_input = lpc32xx_gpio_dir_in_always,
+ .get = lpc32xx_gpi_get_value,
+ .request = lpc32xx_gpio_request,
+ .base = LPC32XX_GPI_P3_GRP,
+ .ngpio = LPC32XX_GPI_P3_MAX,
+ .names = gpi_p3_names,
+ .can_sleep = 0,
+ },
+ .gpio_grp = &gpio_grp_regs_p3,
+ },
+ {
+ .chip = {
+ .label = "gpo_p3",
+ .direction_output = lpc32xx_gpio_dir_out_always,
+ .set = lpc32xx_gpo_set_value,
+ .request = lpc32xx_gpio_request,
+ .base = LPC32XX_GPO_P3_GRP,
+ .ngpio = LPC32XX_GPO_P3_MAX,
+ .names = gpo_p3_names,
+ .can_sleep = 0,
+ },
+ .gpio_grp = &gpio_grp_regs_p3,
+ },
+};
+
+void __init lpc32xx_gpio_init(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(lpc32xx_gpiochip); i++)
+ gpiochip_add(&lpc32xx_gpiochip[i].chip);
+}
diff --git a/arch/arm/mach-lpc32xx/irq.c b/arch/arm/mach-lpc32xx/irq.c
new file mode 100644
index 0000000..4253722
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/irq.c
@@ -0,0 +1,434 @@
+/*
+ * arch/arm/mach-lpc32xx/irq.c
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <mach/irqs.h>
+#include <mach/hardware.h>
+#include <mach/platform.h>
+#include "common.h"
+
+/*
+ * Default value representing the Activation polarity of all internal
+ * interrupt sources
+ */
+#define MIC_APR_DEFAULT 0x3FF0EFE0
+#define SIC1_APR_DEFAULT 0xFBD27186
+#define SIC2_APR_DEFAULT 0x801810C0
+
+/*
+ * Default value representing the Activation Type of all internal
+ * interrupt sources. All are level sensitive.
+ */
+#define MIC_ATR_DEFAULT 0x00000000
+#define SIC1_ATR_DEFAULT 0x00026000
+#define SIC2_ATR_DEFAULT 0x00000000
+
+struct lpc32xx_event_group_regs {
+ void __iomem *enab_reg;
+ void __iomem *edge_reg;
+ void __iomem *maskstat_reg;
+ void __iomem *rawstat_reg;
+};
+
+static const struct lpc32xx_event_group_regs lpc32xx_event_int_regs = {
+ .enab_reg = LPC32XX_CLKPWR_INT_ER,
+ .edge_reg = LPC32XX_CLKPWR_INT_AP,
+ .maskstat_reg = LPC32XX_CLKPWR_INT_SR,
+ .rawstat_reg = LPC32XX_CLKPWR_INT_RS,
+};
+
+static const struct lpc32xx_event_group_regs lpc32xx_event_pin_regs = {
+ .enab_reg = LPC32XX_CLKPWR_PIN_ER,
+ .edge_reg = LPC32XX_CLKPWR_PIN_AP,
+ .maskstat_reg = LPC32XX_CLKPWR_PIN_SR,
+ .rawstat_reg = LPC32XX_CLKPWR_PIN_RS,
+};
+
+struct lpc32xx_event_info {
+ const struct lpc32xx_event_group_regs *event_group;
+ u32 mask;
+};
+
+/*
+ * Maps an IRQ number to and event mask and register
+ */
+static const struct lpc32xx_event_info lpc32xx_events[NR_IRQS] = {
+ [IRQ_LPC32XX_GPI_08] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_08_BIT,
+ },
+ [IRQ_LPC32XX_GPI_09] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_09_BIT,
+ },
+ [IRQ_LPC32XX_GPI_19] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_19_BIT,
+ },
+ [IRQ_LPC32XX_GPI_07] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_07_BIT,
+ },
+ [IRQ_LPC32XX_GPI_00] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_00_BIT,
+ },
+ [IRQ_LPC32XX_GPI_01] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_01_BIT,
+ },
+ [IRQ_LPC32XX_GPI_02] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_02_BIT,
+ },
+ [IRQ_LPC32XX_GPI_03] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_03_BIT,
+ },
+ [IRQ_LPC32XX_GPI_04] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_04_BIT,
+ },
+ [IRQ_LPC32XX_GPI_05] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_05_BIT,
+ },
+ [IRQ_LPC32XX_GPI_06] = {
+ .event_group = &lpc32xx_event_pin_regs,
+ .mask = LPC32XX_CLKPWR_EXTSRC_GPI_06_BIT,
+ },
+ [IRQ_LPC32XX_GPIO_00] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_GPIO_00_BIT,
+ },
+ [IRQ_LPC32XX_GPIO_01] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_GPIO_01_BIT,
+ },
+ [IRQ_LPC32XX_GPIO_02] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_GPIO_02_BIT,
+ },
+ [IRQ_LPC32XX_GPIO_03] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_GPIO_03_BIT,
+ },
+ [IRQ_LPC32XX_GPIO_04] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_GPIO_04_BIT,
+ },
+ [IRQ_LPC32XX_GPIO_05] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_GPIO_05_BIT,
+ },
+ [IRQ_LPC32XX_KEY] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_KEY_BIT,
+ },
+ [IRQ_LPC32XX_USB_OTG_ATX] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_USBATXINT_BIT,
+ },
+ [IRQ_LPC32XX_USB_HOST] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_USB_BIT,
+ },
+ [IRQ_LPC32XX_RTC] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_RTC_BIT,
+ },
+ [IRQ_LPC32XX_MSTIMER] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_MSTIMER_BIT,
+ },
+ [IRQ_LPC32XX_TS_AUX] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_TS_AUX_BIT,
+ },
+ [IRQ_LPC32XX_TS_P] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_TS_P_BIT,
+ },
+ [IRQ_LPC32XX_TS_IRQ] = {
+ .event_group = &lpc32xx_event_int_regs,
+ .mask = LPC32XX_CLKPWR_INTSRC_ADC_BIT,
+ },
+};
+
+static void get_controller(unsigned int irq, unsigned int *base,
+ unsigned int *irqbit)
+{
+ if (irq < 32) {
+ *base = LPC32XX_MIC_BASE;
+ *irqbit = 1 << irq;
+ } else if (irq < 64) {
+ *base = LPC32XX_SIC1_BASE;
+ *irqbit = 1 << (irq - 32);
+ } else {
+ *base = LPC32XX_SIC2_BASE;
+ *irqbit = 1 << (irq - 64);
+ }
+}
+
+static void lpc32xx_mask_irq(unsigned int irq)
+{
+ unsigned int reg, ctrl, mask;
+
+ get_controller(irq, &ctrl, &mask);
+
+ reg = __raw_readl(LPC32XX_INTC_MASK(ctrl)) & ~mask;
+ __raw_writel(reg, LPC32XX_INTC_MASK(ctrl));
+}
+
+static void lpc32xx_unmask_irq(unsigned int irq)
+{
+ unsigned int reg, ctrl, mask;
+
+ get_controller(irq, &ctrl, &mask);
+
+ reg = __raw_readl(LPC32XX_INTC_MASK(ctrl)) | mask;
+ __raw_writel(reg, LPC32XX_INTC_MASK(ctrl));
+}
+
+static void lpc32xx_ack_irq(unsigned int irq)
+{
+ unsigned int ctrl, mask;
+
+ get_controller(irq, &ctrl, &mask);
+
+ __raw_writel(mask, LPC32XX_INTC_RAW_STAT(ctrl));
+
+ /* Also need to clear pending wake event */
+ if (lpc32xx_events[irq].mask != 0)
+ __raw_writel(lpc32xx_events[irq].mask,
+ lpc32xx_events[irq].event_group->rawstat_reg);
+}
+
+static void __lpc32xx_set_irq_type(unsigned int irq, int use_high_level,
+ int use_edge)
+{
+ unsigned int reg, ctrl, mask;
+
+ get_controller(irq, &ctrl, &mask);
+
+ /* Activation level, high or low */
+ reg = __raw_readl(LPC32XX_INTC_POLAR(ctrl));
+ if (use_high_level)
+ reg |= mask;
+ else
+ reg &= ~mask;
+ __raw_writel(reg, LPC32XX_INTC_POLAR(ctrl));
+
+ /* Activation type, edge or level */
+ reg = __raw_readl(LPC32XX_INTC_ACT_TYPE(ctrl));
+ if (use_edge) {
+ reg |= mask;
+ set_irq_handler(irq, handle_edge_irq);
+ } else {
+ reg &= ~mask;
+ set_irq_handler(irq, handle_level_irq);
+ }
+
+ /* Use same polarity for the wake events */
+ if (lpc32xx_events[irq].mask != 0) {
+ reg = __raw_readl(lpc32xx_events[irq].event_group->edge_reg);
+
+ if (use_high_level)
+ reg |= lpc32xx_events[irq].mask;
+ else
+ reg &= ~lpc32xx_events[irq].mask;
+
+ __raw_writel(reg, lpc32xx_events[irq].event_group->edge_reg);
+ }
+}
+
+static int lpc32xx_set_irq_type(unsigned int irq, unsigned int type)
+{
+ switch (type) {
+ case IRQ_TYPE_EDGE_RISING:
+ /* Rising edge sensitive */
+ __lpc32xx_set_irq_type(irq, 1, 1);
+ break;
+
+ case IRQ_TYPE_EDGE_FALLING:
+ /* Falling edge sensitive */
+ __lpc32xx_set_irq_type(irq, 0, 1);
+ break;
+
+ case IRQ_TYPE_LEVEL_LOW:
+ /* Low level sensitive */
+ __lpc32xx_set_irq_type(irq, 0, 0);
+ break;
+
+ case IRQ_TYPE_LEVEL_HIGH:
+ /* High level sensitive */
+ __lpc32xx_set_irq_type(irq, 1, 0);
+ break;
+
+ /* Other modes are not supported */
+ default:
+ return -EINVAL;
+ }
+
+ /* Ok to use the level handler for all types */
+ set_irq_handler(irq, handle_level_irq);
+
+ return 0;
+}
+
+static int lpc32xx_irq_wake(unsigned int irqno, unsigned int state)
+{
+ unsigned long eventreg;
+
+ if (lpc32xx_events[irqno].mask != 0) {
+ eventreg = __raw_readl(lpc32xx_events[irqno].
+ event_group->enab_reg);
+
+ if (state)
+ eventreg |= lpc32xx_events[irqno].mask;
+ else
+ eventreg &= ~lpc32xx_events[irqno].mask;
+
+ __raw_writel(eventreg,
+ lpc32xx_events[irqno].event_group->enab_reg);
+
+ return 0;
+ }
+
+ /* Clear event */
+ __raw_writel(lpc32xx_events[irqno].mask,
+ lpc32xx_events[irqno].event_group->rawstat_reg);
+
+ return -ENODEV;
+}
+
+static void __init lpc32xx_set_default_mappings(unsigned int apr,
+ unsigned int atr, unsigned int offset)
+{
+ unsigned int i;
+
+ /* Set activation levels for each interrupt */
+ i = 0;
+ while (i < 32) {
+ __lpc32xx_set_irq_type(offset + i, ((apr >> i) & 0x1),
+ ((atr >> i) & 0x1));
+ i++;
+ }
+}
+
+static struct irq_chip lpc32xx_irq_chip = {
+ .ack = lpc32xx_ack_irq,
+ .mask = lpc32xx_mask_irq,
+ .unmask = lpc32xx_unmask_irq,
+ .set_type = lpc32xx_set_irq_type,
+ .set_wake = lpc32xx_irq_wake
+};
+
+static void lpc32xx_sic1_handler(unsigned int irq, struct irq_desc *desc)
+{
+ unsigned long ints = __raw_readl(LPC32XX_INTC_STAT(LPC32XX_SIC1_BASE));
+
+ while (ints != 0) {
+ int irqno = fls(ints) - 1;
+
+ ints &= ~(1 << irqno);
+
+ generic_handle_irq(LPC32XX_SIC1_IRQ(irqno));
+ }
+}
+
+static void lpc32xx_sic2_handler(unsigned int irq, struct irq_desc *desc)
+{
+ unsigned long ints = __raw_readl(LPC32XX_INTC_STAT(LPC32XX_SIC2_BASE));
+
+ while (ints != 0) {
+ int irqno = fls(ints) - 1;
+
+ ints &= ~(1 << irqno);
+
+ generic_handle_irq(LPC32XX_SIC2_IRQ(irqno));
+ }
+}
+
+void __init lpc32xx_init_irq(void)
+{
+ unsigned int i;
+
+ /* Setup MIC */
+ __raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_MIC_BASE));
+ __raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_MIC_BASE));
+ __raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_MIC_BASE));
+
+ /* Setup SIC1 */
+ __raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC1_BASE));
+ __raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC1_BASE));
+ __raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC1_BASE));
+
+ /* Setup SIC2 */
+ __raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC2_BASE));
+ __raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC2_BASE));
+ __raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC2_BASE));
+
+ /* Configure supported IRQ's */
+ for (i = 0; i < NR_IRQS; i++) {
+ set_irq_chip(i, &lpc32xx_irq_chip);
+ set_irq_handler(i, handle_level_irq);
+ set_irq_flags(i, IRQF_VALID);
+ }
+
+ /* Set default mappings */
+ lpc32xx_set_default_mappings(MIC_APR_DEFAULT, MIC_ATR_DEFAULT, 0);
+ lpc32xx_set_default_mappings(SIC1_APR_DEFAULT, SIC1_ATR_DEFAULT, 32);
+ lpc32xx_set_default_mappings(SIC2_APR_DEFAULT, SIC2_ATR_DEFAULT, 64);
+
+ /* mask all interrupts except SUBIRQ */
+ __raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_MIC_BASE));
+ __raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC1_BASE));
+ __raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC2_BASE));
+
+ /* MIC SUBIRQx interrupts will route handling to the chain handlers */
+ set_irq_chained_handler(IRQ_LPC32XX_SUB1IRQ, lpc32xx_sic1_handler);
+ set_irq_chained_handler(IRQ_LPC32XX_SUB2IRQ, lpc32xx_sic2_handler);
+
+ /* Initially disable all wake events */
+ __raw_writel(0, LPC32XX_CLKPWR_P01_ER);
+ __raw_writel(0, LPC32XX_CLKPWR_INT_ER);
+ __raw_writel(0, LPC32XX_CLKPWR_PIN_ER);
+
+ /*
+ * Default wake activation polarities, all pin sources are low edge
+ * triggered
+ */
+ __raw_writel(LPC32XX_CLKPWR_INTSRC_TS_P_BIT |
+ LPC32XX_CLKPWR_INTSRC_MSTIMER_BIT |
+ LPC32XX_CLKPWR_INTSRC_RTC_BIT,
+ LPC32XX_CLKPWR_INT_AP);
+ __raw_writel(0, LPC32XX_CLKPWR_PIN_AP);
+
+ /* Clear latched wake event states */
+ __raw_writel(__raw_readl(LPC32XX_CLKPWR_PIN_RS),
+ LPC32XX_CLKPWR_PIN_RS);
+ __raw_writel(__raw_readl(LPC32XX_CLKPWR_INT_RS),
+ LPC32XX_CLKPWR_INT_RS);
+}
diff --git a/arch/arm/mach-lpc32xx/timer.c b/arch/arm/mach-lpc32xx/timer.c
new file mode 100644
index 0000000..630dd4a
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/timer.c
@@ -0,0 +1,182 @@
+/*
+ * arch/arm/mach-lpc32xx/timer.c
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2009 - 2010 NXP Semiconductors
+ * Copyright (C) 2009 Fontys University of Applied Sciences, Eindhoven
+ * Ed Schouten <e.schouten@fontys.nl>
+ * Laurens Timmermans <l.timmermans@fontys.nl>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/time.h>
+#include <linux/err.h>
+#include <linux/clockchips.h>
+
+#include <asm/mach/time.h>
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+#include "common.h"
+
+static cycle_t lpc32xx_clksrc_read(struct clocksource *cs)
+{
+ return (cycle_t)__raw_readl(LCP32XX_TIMER_TC(LPC32XX_TIMER1_BASE));
+}
+
+static struct clocksource lpc32xx_clksrc = {
+ .name = "lpc32xx_clksrc",
+ .shift = 24,
+ .rating = 300,
+ .read = lpc32xx_clksrc_read,
+ .mask = CLOCKSOURCE_MASK(32),
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static int lpc32xx_clkevt_next_event(unsigned long delta,
+ struct clock_event_device *dev)
+{
+ __raw_writel(LCP32XX_TIMER_CNTR_TCR_RESET,
+ LCP32XX_TIMER_TCR(LPC32XX_TIMER0_BASE));
+ __raw_writel(delta, LCP32XX_TIMER_PR(LPC32XX_TIMER0_BASE));
+ __raw_writel(LCP32XX_TIMER_CNTR_TCR_EN,
+ LCP32XX_TIMER_TCR(LPC32XX_TIMER0_BASE));
+
+ return 0;
+}
+
+static void lpc32xx_clkevt_mode(enum clock_event_mode mode,
+ struct clock_event_device *dev)
+{
+ switch (mode) {
+ case CLOCK_EVT_MODE_PERIODIC:
+ WARN_ON(1);
+ break;
+
+ case CLOCK_EVT_MODE_ONESHOT:
+ case CLOCK_EVT_MODE_SHUTDOWN:
+ /*
+ * Disable the timer. When using oneshot, we must also
+ * disable the timer to wait for the first call to
+ * set_next_event().
+ */
+ __raw_writel(0, LCP32XX_TIMER_TCR(LPC32XX_TIMER0_BASE));
+ break;
+
+ case CLOCK_EVT_MODE_UNUSED:
+ case CLOCK_EVT_MODE_RESUME:
+ break;
+ }
+}
+
+static struct clock_event_device lpc32xx_clkevt = {
+ .name = "lpc32xx_clkevt",
+ .features = CLOCK_EVT_FEAT_ONESHOT,
+ .shift = 32,
+ .rating = 300,
+ .set_next_event = lpc32xx_clkevt_next_event,
+ .set_mode = lpc32xx_clkevt_mode,
+};
+
+static irqreturn_t lpc32xx_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = &lpc32xx_clkevt;
+
+ /* Clear match */
+ __raw_writel(LCP32XX_TIMER_CNTR_MTCH_BIT(0),
+ LCP32XX_TIMER_IR(LPC32XX_TIMER0_BASE));
+
+ evt->event_handler(evt);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction lpc32xx_timer_irq = {
+ .name = "LPC32XX Timer Tick",
+ .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+ .handler = lpc32xx_timer_interrupt,
+};
+
+/*
+ * The clock management driver isn't initialized at this point, so the
+ * clocks need to be enabled here manually and then tagged as used in
+ * the clock driver initialization
+ */
+static void __init lpc32xx_timer_init(void)
+{
+ u32 clkrate, pllreg;
+
+ /* Enable timer clock */
+ __raw_writel(LPC32XX_CLKPWR_TMRPWMCLK_TIMER0_EN |
+ LPC32XX_CLKPWR_TMRPWMCLK_TIMER1_EN,
+ LPC32XX_CLKPWR_TIMERS_PWMS_CLK_CTRL_1);
+
+ /*
+ * The clock driver isn't initialized at this point. So determine if
+ * the SYSCLK is driven from the PLL397 or main oscillator and then use
+ * it to compute the PLL frequency and the PCLK divider to get the base
+ * timer rates. This rate is needed to compute the tick rate.
+ */
+ if (clk_is_sysclk_mainosc() != 0)
+ clkrate = LPC32XX_MAIN_OSC_FREQ;
+ else
+ clkrate = 397 * LPC32XX_CLOCK_OSC_FREQ;
+
+ /* Get ARM HCLKPLL register and convert it into a frequency */
+ pllreg = __raw_readl(LPC32XX_CLKPWR_HCLKPLL_CTRL) & 0x1FFFF;
+ clkrate = clk_get_pllrate_from_reg(clkrate, pllreg);
+
+ /* Get PCLK divider and divide ARM PLL clock by it to get timer rate */
+ clkrate = clkrate / clk_get_pclk_div();
+
+ /* Initial timer setup */
+ __raw_writel(0, LCP32XX_TIMER_TCR(LPC32XX_TIMER0_BASE));
+ __raw_writel(LCP32XX_TIMER_CNTR_MTCH_BIT(0),
+ LCP32XX_TIMER_IR(LPC32XX_TIMER0_BASE));
+ __raw_writel(1, LCP32XX_TIMER_MR0(LPC32XX_TIMER0_BASE));
+ __raw_writel(LCP32XX_TIMER_CNTR_MCR_MTCH(0) |
+ LCP32XX_TIMER_CNTR_MCR_STOP(0) |
+ LCP32XX_TIMER_CNTR_MCR_RESET(0),
+ LCP32XX_TIMER_MCR(LPC32XX_TIMER0_BASE));
+
+ /* Setup tick interrupt */
+ setup_irq(IRQ_LPC32XX_TIMER0, &lpc32xx_timer_irq);
+
+ /* Setup the clockevent structure. */
+ lpc32xx_clkevt.mult = div_sc(clkrate, NSEC_PER_SEC,
+ lpc32xx_clkevt.shift);
+ lpc32xx_clkevt.max_delta_ns = clockevent_delta2ns(-1,
+ &lpc32xx_clkevt);
+ lpc32xx_clkevt.min_delta_ns = clockevent_delta2ns(1,
+ &lpc32xx_clkevt) + 1;
+ lpc32xx_clkevt.cpumask = cpumask_of(0);
+ clockevents_register_device(&lpc32xx_clkevt);
+
+ /* Use timer1 as clock source. */
+ __raw_writel(LCP32XX_TIMER_CNTR_TCR_RESET,
+ LCP32XX_TIMER_TCR(LPC32XX_TIMER1_BASE));
+ __raw_writel(0, LCP32XX_TIMER_PR(LPC32XX_TIMER1_BASE));
+ __raw_writel(0, LCP32XX_TIMER_MCR(LPC32XX_TIMER1_BASE));
+ __raw_writel(LCP32XX_TIMER_CNTR_TCR_EN,
+ LCP32XX_TIMER_TCR(LPC32XX_TIMER1_BASE));
+ lpc32xx_clksrc.mult = clocksource_hz2mult(clkrate,
+ lpc32xx_clksrc.shift);
+ clocksource_register(&lpc32xx_clksrc);
+}
+
+struct sys_timer lpc32xx_timer = {
+ .init = &lpc32xx_timer_init,
+};
+
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 05/13] ARM: LPC32XX: System suspend support
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (3 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 04/13] ARM: LPC32XX: GPIO, timer, and IRQ drivers wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 06/13] ARM: LPC32XX: Serial support code wellsk40 at gmail.com
` (7 subsequent siblings)
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Support for system suspend and resume
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/pm.c | 145 +++++++++++++++++++++++++++++++++++++
arch/arm/mach-lpc32xx/suspend.S | 151 +++++++++++++++++++++++++++++++++++++++
2 files changed, 296 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/pm.c b/arch/arm/mach-lpc32xx/pm.c
new file mode 100644
index 0000000..d792e2e
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/pm.c
@@ -0,0 +1,145 @@
+/*
+ * arch/arm/mach-lpc32xx/pm.c
+ *
+ * Original authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
+ * Modified by Kevin Wells <kevin.wells@nxp.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+/*
+ * LPC32XX CPU and system power management
+ *
+ * The LCP32XX has three CPU modes for controlling system power: run,
+ * direct-run, and halt modes. When switching between halt and run modes,
+ * the CPU transistions through direct-run mode. For Linux, direct-run
+ * mode is not used in normal operation. Halt mode is used when the
+ * system is fully suspended.
+ *
+ * Run mode:
+ * The ARM CPU clock (HCLK_PLL), HCLK bus clock, and PCLK bus clocks are
+ * derived from the HCLK PLL. The HCLK and PCLK bus rates are divided from
+ * the HCLK_PLL rate. Linux runs in this mode.
+ *
+ * Direct-run mode:
+ * The ARM CPU clock, HCLK bus clock, and PCLK bus clocks are driven from
+ * SYSCLK. SYSCLK is usually around 13MHz, but may vary based on SYSCLK
+ * source or the frequency of the main oscillator. In this mode, the
+ * HCLK_PLL can be safely enabled, changed, or disabled.
+ *
+ * Halt mode:
+ * SYSCLK is gated off and the CPU and system clocks are halted.
+ * Peripherals based on the 32KHz oscillator clock (ie, RTC, touch,
+ * key scanner, etc.) still operate if enabled. In this state, an enabled
+ * system event (ie, GPIO state change, RTC match, key press, etc.) will
+ * wake the system up back into direct-run mode.
+ *
+ * DRAM refresh
+ * DRAM clocking and refresh are slightly different for systems with DDR
+ * DRAM or regular SDRAM devices. If SDRAM is used in the system, the
+ * SDRAM will still be accessible in direct-run mode. In DDR based systems,
+ * a transistion to direct-run mode will stop all DDR accesses (no clocks).
+ * Because of this, the code to switch power modes and the code to enter
+ * and exit DRAM self-refresh modes must not be executed in DRAM. A small
+ * section of IRAM is used instead for this.
+ *
+ * Suspend is handled with the following logic:
+ * Backup a small area of IRAM used for the suspend code
+ * Copy suspend code to IRAM
+ * Transfer control to code in IRAM
+ * Places DRAMs in self-refresh mode
+ * Enter direct-run mode
+ * Save state of HCLK_PLL PLL
+ * Disable HCLK_PLL PLL
+ * Enter halt mode - CPU and buses will stop
+ * System enters direct-run mode when an enabled event occurs
+ * HCLK PLL state is restored
+ * Run mode is entered
+ * DRAMS are placed back into normal mode
+ * Code execution returns from IRAM
+ * IRAM code are used for suspend is restored
+ * Suspend mode is exited
+ */
+
+#include <linux/suspend.h>
+#include <linux/io.h>
+
+#include <asm/cacheflush.h>
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+#include "common.h"
+#include "clock.h"
+
+#define TEMP_IRAM_AREA IO_ADDRESS(LPC32XX_IRAM_BASE)
+
+/*
+ * Both STANDBY and MEM suspend states are handled the same with no
+ * loss of CPU or memory state
+ */
+static int lpc32xx_pm_enter(suspend_state_t state)
+{
+ int (*lpc32xx_suspend_ptr) (void);
+ void *iram_swap_area;
+
+ /* Allocate some space for temporary IRAM storage */
+ iram_swap_area = kmalloc(lpc32xx_sys_suspend_sz, GFP_KERNEL);
+ if (!iram_swap_area) {
+ printk(KERN_ERR
+ "PM Suspend: cannot allocate memory to save portion "
+ "of SRAM\n");
+ return -ENOMEM;
+ }
+
+ /* Backup a small area of IRAM used for the suspend code */
+ memcpy(iram_swap_area, (void *) TEMP_IRAM_AREA,
+ lpc32xx_sys_suspend_sz);
+
+ /*
+ * Copy code to suspend system into IRAM. The suspend code
+ * needs to run from IRAM as DRAM may no longer be available
+ * when the PLL is stopped.
+ */
+ memcpy((void *) TEMP_IRAM_AREA, &lpc32xx_sys_suspend,
+ lpc32xx_sys_suspend_sz);
+ flush_icache_range((unsigned long)TEMP_IRAM_AREA,
+ (unsigned long)(TEMP_IRAM_AREA) + lpc32xx_sys_suspend_sz);
+
+ /* Transfer to suspend code in IRAM */
+ lpc32xx_suspend_ptr = (void *) TEMP_IRAM_AREA;
+ flush_cache_all();
+ (void) lpc32xx_suspend_ptr();
+
+ /* Restore original IRAM contents */
+ memcpy((void *) TEMP_IRAM_AREA, iram_swap_area,
+ lpc32xx_sys_suspend_sz);
+
+ kfree(iram_swap_area);
+
+ return 0;
+}
+
+static struct platform_suspend_ops lpc32xx_pm_ops = {
+ .valid = suspend_valid_only_mem,
+ .enter = lpc32xx_pm_enter,
+};
+
+#define EMC_DYN_MEM_CTRL_OFS 0x20
+#define EMC_SRMMC (1 << 3)
+#define EMC_CTRL_REG io_p2v(LPC32XX_EMC_BASE + EMC_DYN_MEM_CTRL_OFS)
+static int __init lpc32xx_pm_init(void)
+{
+ /*
+ * Setup SDRAM self-refresh clock to automatically disable o
+ * start of self-refresh. This only needs to be done once.
+ */
+ __raw_writel(__raw_readl(EMC_CTRL_REG) | EMC_SRMMC, EMC_CTRL_REG);
+
+ suspend_set_ops(&lpc32xx_pm_ops);
+
+ return 0;
+}
+arch_initcall(lpc32xx_pm_init);
diff --git a/arch/arm/mach-lpc32xx/suspend.S b/arch/arm/mach-lpc32xx/suspend.S
new file mode 100644
index 0000000..374f9f0
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/suspend.S
@@ -0,0 +1,151 @@
+/*
+ * arch/arm/mach-lpc32xx/suspend.S
+ *
+ * Original authors: Dmitry Chigirev, Vitaly Wool <source@mvista.com>
+ * Modified by Kevin Wells <kevin.wells@nxp.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <mach/platform.h>
+#include <mach/hardware.h>
+
+/* Using named register defines makes the code easier to follow */
+#define WORK1_REG r0
+#define WORK2_REG r1
+#define SAVED_HCLK_DIV_REG r2
+#define SAVED_HCLK_PLL_REG r3
+#define SAVED_DRAM_CLKCTRL_REG r4
+#define SAVED_PWR_CTRL_REG r5
+#define CLKPWRBASE_REG r6
+#define EMCBASE_REG r7
+
+#define LPC32XX_EMC_STATUS_OFFS 0x04
+#define LPC32XX_EMC_STATUS_BUSY 0x1
+#define LPC32XX_EMC_STATUS_SELF_RFSH 0x4
+
+#define LPC32XX_CLKPWR_PWR_CTRL_OFFS 0x44
+#define LPC32XX_CLKPWR_HCLK_DIV_OFFS 0x40
+#define LPC32XX_CLKPWR_HCLKPLL_CTRL_OFFS 0x58
+
+#define CLKPWR_PCLK_DIV_MASK 0xFFFFFE7F
+
+ .text
+
+ENTRY(lpc32xx_sys_suspend)
+ @ Save a copy of the used registers in IRAM, r0 is corrupted
+ adr r0, tmp_stack_end
+ stmfd r0!, {r3 - r7, sp, lr}
+
+ @ Load a few common register addresses
+ adr WORK1_REG, reg_bases
+ ldr CLKPWRBASE_REG, [WORK1_REG, #0]
+ ldr EMCBASE_REG, [WORK1_REG, #4]
+
+ ldr SAVED_PWR_CTRL_REG, [CLKPWRBASE_REG,\
+ #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+ orr WORK1_REG, SAVED_PWR_CTRL_REG, #LPC32XX_CLKPWR_SDRAM_SELF_RFSH
+
+ @ Wait for SDRAM busy status to go busy and then idle
+ @ This guarantees a small windows where DRAM isn't busy
+1:
+ ldr WORK2_REG, [EMCBASE_REG, #LPC32XX_EMC_STATUS_OFFS]
+ and WORK2_REG, WORK2_REG, #LPC32XX_EMC_STATUS_BUSY
+ cmp WORK2_REG, #LPC32XX_EMC_STATUS_BUSY
+ bne 1b @ Branch while idle
+2:
+ ldr WORK2_REG, [EMCBASE_REG, #LPC32XX_EMC_STATUS_OFFS]
+ and WORK2_REG, WORK2_REG, #LPC32XX_EMC_STATUS_BUSY
+ cmp WORK2_REG, #LPC32XX_EMC_STATUS_BUSY
+ beq 2b @ Branch until idle
+
+ @ Setup self-refresh with support for manual exit of
+ @ self-refresh mode
+ str WORK1_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+ orr WORK2_REG, WORK1_REG, #LPC32XX_CLKPWR_UPD_SDRAM_SELF_RFSH
+ str WORK2_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+ str WORK1_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+
+ @ Wait for self-refresh acknowledge, clocks to the DRAM device
+ @ will automatically stop on start of self-refresh
+3:
+ ldr WORK2_REG, [EMCBASE_REG, #LPC32XX_EMC_STATUS_OFFS]
+ and WORK2_REG, WORK2_REG, #LPC32XX_EMC_STATUS_SELF_RFSH
+ cmp WORK2_REG, #LPC32XX_EMC_STATUS_SELF_RFSH
+ bne 3b @ Branch until self-refresh mode starts
+
+ @ Enter direct-run mode from run mode
+ bic WORK1_REG, WORK1_REG, #LPC32XX_CLKPWR_SELECT_RUN_MODE
+ str WORK1_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+
+ @ Safe disable of DRAM clock in EMC block, prevents DDR sync
+ @ issues on restart
+ ldr SAVED_HCLK_DIV_REG, [CLKPWRBASE_REG,\
+ #LPC32XX_CLKPWR_HCLK_DIV_OFFS]
+ and WORK2_REG, SAVED_HCLK_DIV_REG, #CLKPWR_PCLK_DIV_MASK
+ str WORK2_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_HCLK_DIV_OFFS]
+
+ @ Save HCLK PLL state and disable HCLK PLL
+ ldr SAVED_HCLK_PLL_REG, [CLKPWRBASE_REG,\
+ #LPC32XX_CLKPWR_HCLKPLL_CTRL_OFFS]
+ bic WORK2_REG, SAVED_HCLK_PLL_REG, #LPC32XX_CLKPWR_HCLKPLL_POWER_UP
+ str WORK2_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_HCLKPLL_CTRL_OFFS]
+
+ @ Enter stop mode until an enabled event occurs
+ orr WORK1_REG, WORK1_REG, #LPC32XX_CLKPWR_STOP_MODE_CTRL
+ str WORK1_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+ .rept 9
+ nop
+ .endr
+
+ @ Clear stop status
+ bic WORK1_REG, WORK1_REG, #LPC32XX_CLKPWR_STOP_MODE_CTRL
+
+ @ Restore original HCLK PLL value and wait for PLL lock
+ str SAVED_HCLK_PLL_REG, [CLKPWRBASE_REG,\
+ #LPC32XX_CLKPWR_HCLKPLL_CTRL_OFFS]
+4:
+ ldr WORK2_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_HCLKPLL_CTRL_OFFS]
+ and WORK2_REG, WORK2_REG, #LPC32XX_CLKPWR_HCLKPLL_PLL_STS
+ bne 4b
+
+ @ Re-enter run mode with self-refresh flag cleared, but no DRAM
+ @ update yet. DRAM is still in self-refresh
+ str SAVED_PWR_CTRL_REG, [CLKPWRBASE_REG,\
+ #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+
+ @ Restore original DRAM clock mode to restore DRAM clocks
+ str SAVED_HCLK_DIV_REG, [CLKPWRBASE_REG,\
+ #LPC32XX_CLKPWR_HCLK_DIV_OFFS]
+
+ @ Clear self-refresh mode
+ orr WORK1_REG, SAVED_PWR_CTRL_REG,\
+ #LPC32XX_CLKPWR_UPD_SDRAM_SELF_RFSH
+ str WORK1_REG, [CLKPWRBASE_REG, #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+ str SAVED_PWR_CTRL_REG, [CLKPWRBASE_REG,\
+ #LPC32XX_CLKPWR_PWR_CTRL_OFFS]
+
+ @ Wait for EMC to clear self-refresh mode
+5:
+ ldr WORK2_REG, [EMCBASE_REG, #LPC32XX_EMC_STATUS_OFFS]
+ and WORK2_REG, WORK2_REG, #LPC32XX_EMC_STATUS_SELF_RFSH
+ bne 5b @ Branch until self-refresh has exited
+
+ @ restore regs and return
+ adr r0, tmp_stack
+ ldmfd r0!, {r3 - r7, sp, pc}
+
+reg_bases:
+ .long IO_ADDRESS(LPC32XX_CLK_PM_BASE)
+ .long IO_ADDRESS(LPC32XX_EMC_BASE)
+
+tmp_stack:
+ .long 0, 0, 0, 0, 0, 0, 0
+tmp_stack_end:
+
+ENTRY(lpc32xx_sys_suspend_sz)
+ .word . - lpc32xx_sys_suspend
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 06/13] ARM: LPC32XX: Serial support code
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (4 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 05/13] ARM: LPC32XX: System suspend support wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-20 16:34 ` Russell King - ARM Linux
2010-02-19 23:26 ` [PATCH 07/13] ARM: LPC32XX: Misc support functions wellsk40 at gmail.com
` (6 subsequent siblings)
12 siblings, 1 reply; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Serial port setup support code
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/serial.c | 191 ++++++++++++++++++++++++++++++++++++++++
1 files changed, 191 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/serial.c b/arch/arm/mach-lpc32xx/serial.c
new file mode 100644
index 0000000..680a79b
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/serial.c
@@ -0,0 +1,191 @@
+/*
+ * arch/arm/mach-lpc32xx/serial.c
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+#include <linux/serial_8250.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+#include <mach/io.h>
+#include "common.h"
+
+#define LPC32XX_SUART_FIFO_SIZE 64
+
+/* Standard 8250/16550 compatible serial ports */
+static struct plat_serial8250_port serial_std_platform_data[] = {
+#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT
+ {
+ .membase = io_p2v(LPC32XX_UART5_BASE),
+ .mapbase = LPC32XX_UART5_BASE,
+ .irq = IRQ_LPC32XX_UART_IIR5,
+ .uartclk = LPC32XX_MAIN_OSC_FREQ,
+ .regshift = 2,
+ .iotype = UPIO_MEM32,
+ .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
+ UPF_SKIP_TEST,
+ },
+#endif
+#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
+ {
+ .membase = io_p2v(LPC32XX_UART3_BASE),
+ .mapbase = LPC32XX_UART3_BASE,
+ .irq = IRQ_LPC32XX_UART_IIR3,
+ .uartclk = LPC32XX_MAIN_OSC_FREQ,
+ .regshift = 2,
+ .iotype = UPIO_MEM32,
+ .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
+ UPF_SKIP_TEST,
+ },
+#endif
+#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
+ {
+ .membase = io_p2v(LPC32XX_UART4_BASE),
+ .mapbase = LPC32XX_UART4_BASE,
+ .irq = IRQ_LPC32XX_UART_IIR4,
+ .uartclk = LPC32XX_MAIN_OSC_FREQ,
+ .regshift = 2,
+ .iotype = UPIO_MEM32,
+ .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
+ UPF_SKIP_TEST,
+ },
+#endif
+#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
+ {
+ .membase = io_p2v(LPC32XX_UART6_BASE),
+ .mapbase = LPC32XX_UART6_BASE,
+ .irq = IRQ_LPC32XX_UART_IIR6,
+ .uartclk = LPC32XX_MAIN_OSC_FREQ,
+ .regshift = 2,
+ .iotype = UPIO_MEM32,
+ .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
+ UPF_SKIP_TEST,
+ },
+#endif
+ { },
+};
+
+struct uartinit {
+ char *uart_ck_name;
+ u32 ck_mode_mask;
+ void __iomem *pdiv_clk_reg;
+};
+
+static struct uartinit uartinit_data[] __initdata = {
+#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT
+ {
+ .uart_ck_name = "uart5_ck",
+ .ck_mode_mask =
+ LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 5),
+ .pdiv_clk_reg = LPC32XX_CLKPWR_UART5_CLK_CTRL,
+ },
+#endif
+#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
+ {
+ .uart_ck_name = "uart3_ck",
+ .ck_mode_mask =
+ LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 3),
+ .pdiv_clk_reg = LPC32XX_CLKPWR_UART3_CLK_CTRL,
+ },
+#endif
+#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
+ {
+ .uart_ck_name = "uart4_ck",
+ .ck_mode_mask =
+ LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 4),
+ .pdiv_clk_reg = LPC32XX_CLKPWR_UART4_CLK_CTRL,
+ },
+#endif
+#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
+ {
+ .uart_ck_name = "uart6_ck",
+ .ck_mode_mask =
+ LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 6),
+ .pdiv_clk_reg = LPC32XX_CLKPWR_UART6_CLK_CTRL,
+ },
+#endif
+};
+
+static struct platform_device serial_std_platform_device = {
+ .name = "serial8250",
+ .id = 0,
+ .dev = {
+ .platform_data = serial_std_platform_data,
+ },
+};
+
+static struct platform_device *lpc32xx_serial_devs[] __initdata = {
+ &serial_std_platform_device,
+};
+
+void __init lpc32xx_serial_init(void)
+{
+ u32 tmp, clkmodes = 0;
+ struct clk *clk;
+ unsigned int puart;
+ int i, j;
+
+ /* UART clocks are off, let clock driver manage them */
+ __raw_writel(0, LPC32XX_CLKPWR_UART_CLK_CTRL);
+
+ for (i = 0; i < ARRAY_SIZE(uartinit_data); i++) {
+ clk = clk_get(NULL, uartinit_data[i].uart_ck_name);
+ if (!IS_ERR(clk)) {
+ clk_enable(clk);
+ serial_std_platform_data[i].uartclk =
+ clk_get_rate(clk);
+ }
+
+ /* Fall back on main osc rate if clock rate return fails */
+ if (serial_std_platform_data[i].uartclk == 0)
+ serial_std_platform_data[i].uartclk =
+ LPC32XX_MAIN_OSC_FREQ;
+
+ /* Setup UART clock modes for all UARTs, disable autoclock */
+ clkmodes |= uartinit_data[i].ck_mode_mask;
+
+ /* pre-UART clock divider set to 1 */
+ __raw_writel(0x0101, uartinit_data[i].pdiv_clk_reg);
+ }
+
+ /* This needs to be done after all UART clocks are setup */
+ __raw_writel(clkmodes, LPC32XX_UARTCTL_CLKMODE);
+ for (i = 0; i < ARRAY_SIZE(uartinit_data) - 1; i++) {
+ /* Force a flush of the RX FIFOs to work around a HW bug */
+ puart = serial_std_platform_data[i].mapbase;
+ __raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart));
+ __raw_writel(0x00, LPC32XX_UART_DLL_FIFO(puart));
+ j = LPC32XX_SUART_FIFO_SIZE;
+ while (j--)
+ tmp = __raw_readl(LPC32XX_UART_DLL_FIFO(puart));
+ __raw_writel(0, LPC32XX_UART_IIR_FCR(puart));
+ }
+
+ /* Disable UART5->USB transparent mode or USB won't work */
+ tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
+ tmp &= ~LPC32XX_UART_U5_ROUTE_TO_USB;
+ __raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
+
+ platform_add_devices(lpc32xx_serial_devs,
+ ARRAY_SIZE(lpc32xx_serial_devs));
+}
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 07/13] ARM: LPC32XX: Misc support functions
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (5 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 06/13] ARM: LPC32XX: Serial support code wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 08/13] ARM: LPC32XX: Phytec 3250 platform support wellsk40 at gmail.com
` (5 subsequent siblings)
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Misc support functions and prototypes used in the LPC32XX arch
and platforms
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/common.c | 271 ++++++++++++++++++++++++++++++++++++++++
arch/arm/mach-lpc32xx/common.h | 73 +++++++++++
2 files changed, 344 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/common.c b/arch/arm/mach-lpc32xx/common.c
new file mode 100644
index 0000000..ee24dc2
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/common.c
@@ -0,0 +1,271 @@
+/*
+ * arch/arm/mach-lpc32xx/common.c
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/i2c-pnx.h>
+#include <linux/io.h>
+
+#include <asm/mach/map.h>
+
+#include <mach/i2c.h>
+#include <mach/hardware.h>
+#include <mach/platform.h>
+#include "common.h"
+
+/*
+ * Watchdog timer
+ */
+static struct resource watchdog_resources[] = {
+ [0] = {
+ .start = LPC32XX_WDTIM_BASE,
+ .end = LPC32XX_WDTIM_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+struct platform_device lpc32xx_watchdog_device = {
+ .name = "pnx4008-watchdog",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(watchdog_resources),
+ .resource = watchdog_resources,
+};
+
+/*
+ * I2C busses
+ */
+static struct i2c_pnx_data i2c0_data = {
+ .name = I2C_CHIP_NAME "1",
+ .base = LPC32XX_I2C1_BASE,
+ .irq = IRQ_LPC32XX_I2C_1,
+};
+
+static struct i2c_pnx_data i2c1_data = {
+ .name = I2C_CHIP_NAME "2",
+ .base = LPC32XX_I2C2_BASE,
+ .irq = IRQ_LPC32XX_I2C_2,
+};
+
+static struct i2c_pnx_data i2c2_data = {
+ .name = "USB-I2C",
+ .base = LPC32XX_OTG_I2C_BASE,
+ .irq = IRQ_LPC32XX_USB_I2C,
+};
+
+struct platform_device lpc32xx_i2c0_device = {
+ .name = "pnx-i2c",
+ .id = 0,
+ .dev = {
+ .platform_data = &i2c0_data,
+ },
+};
+
+struct platform_device lpc32xx_i2c1_device = {
+ .name = "pnx-i2c",
+ .id = 1,
+ .dev = {
+ .platform_data = &i2c1_data,
+ },
+};
+
+struct platform_device lpc32xx_i2c2_device = {
+ .name = "pnx-i2c",
+ .id = 2,
+ .dev = {
+ .platform_data = &i2c2_data,
+ },
+};
+
+/*
+ * Returns the unique ID for the device
+ */
+void lpc32xx_get_uid(u32 devid[4])
+{
+ int i;
+
+ for (i = 0; i < 4; i++)
+ devid[i] = __raw_readl(LPC32XX_CLKPWR_DEVID(i << 2));
+}
+
+/*
+ * Returns SYSCLK source
+ * 0 = PLL397, 1 = main oscillator
+ */
+int clk_is_sysclk_mainosc(void)
+{
+ if ((__raw_readl(LPC32XX_CLKPWR_SYSCLK_CTRL) &
+ LPC32XX_CLKPWR_SYSCTRL_SYSCLKMUX) == 0)
+ return 1;
+
+ return 0;
+}
+
+/*
+ * System reset via the watchdog timer
+ */
+void lpc32xx_watchdog_reset(void)
+{
+ /* Make sure WDT clocks are enabled */
+ __raw_writel(LPC32XX_CLKPWR_PWMCLK_WDOG_EN,
+ LPC32XX_CLKPWR_TIMER_CLK_CTRL);
+
+ /* Instant assert of RESETOUT_N with pulse length 1mS */
+ __raw_writel(13000, io_p2v(LPC32XX_WDTIM_BASE + 0x18));
+ __raw_writel(0x70, io_p2v(LPC32XX_WDTIM_BASE + 0xC));
+}
+
+/*
+ * Detects and returns IRAM size for the device variation
+ */
+#define LPC32XX_IRAM_BANK_SIZE SZ_128K
+static u32 iram_size;
+u32 lpc32xx_return_iram_size(void)
+{
+ if (iram_size == 0) {
+ u32 savedval1, savedval2;
+ void __iomem *iramptr1, *iramptr2;
+
+ iramptr1 = io_p2v(LPC32XX_IRAM_BASE);
+ iramptr2 = io_p2v(LPC32XX_IRAM_BASE + LPC32XX_IRAM_BANK_SIZE);
+ savedval1 = __raw_readl(iramptr1);
+ savedval2 = __raw_readl(iramptr2);
+
+ if (savedval1 == savedval2) {
+ __raw_writel(savedval2 + 1, iramptr2);
+ if (__raw_readl(iramptr1) == savedval2 + 1)
+ iram_size = LPC32XX_IRAM_BANK_SIZE;
+ else
+ iram_size = LPC32XX_IRAM_BANK_SIZE * 2;
+ __raw_writel(savedval2, iramptr2);
+ } else
+ iram_size = LPC32XX_IRAM_BANK_SIZE * 2;
+ }
+
+ return iram_size;
+}
+
+/*
+ * Computes PLL rate from PLL register and input clock
+ */
+u32 clk_check_pll_setup(u32 ifreq, struct clk_pll_setup *pllsetup)
+{
+ u32 ilfreq, p, m, n, fcco, fref, cfreq;
+ int mode;
+
+ /*
+ * PLL requirements
+ * ifreq must be >= 1MHz and <= 20MHz
+ * FCCO must be >= 156MHz and <= 320MHz
+ * FREF must be >= 1MHz and <= 27MHz
+ * Assume the passed input data is not valid
+ */
+
+ ilfreq = ifreq;
+ m = pllsetup->pll_m;
+ n = pllsetup->pll_n;
+ p = pllsetup->pll_p;
+
+ mode = (pllsetup->cco_bypass_b15 << 2) |
+ (pllsetup->direct_output_b14 << 1) |
+ pllsetup->fdbk_div_ctrl_b13;
+
+ switch (mode) {
+ case 0x0: /* Non-integer mode */
+ cfreq = (m * ilfreq) / (2 * p * n);
+ fcco = (m * ilfreq) / n;
+ fref = ilfreq / n;
+ break;
+
+ case 0x1: /* integer mode */
+ cfreq = (m * ilfreq) / n;
+ fcco = (m * ilfreq) / (n * 2 * p);
+ fref = ilfreq / n;
+ break;
+
+ case 0x2:
+ case 0x3: /* Direct mode */
+ cfreq = (m * ilfreq) / n;
+ fcco = cfreq;
+ fref = ilfreq / n;
+ break;
+
+ case 0x4:
+ case 0x5: /* Bypass mode */
+ cfreq = ilfreq / (2 * p);
+ fcco = 156000000;
+ fref = 1000000;
+ break;
+
+ case 0x6:
+ case 0x7: /* Direct bypass mode */
+ default:
+ cfreq = ilfreq;
+ fcco = 156000000;
+ fref = 1000000;
+ break;
+ }
+
+ if (fcco < 156000000 || fcco > 320000000)
+ cfreq = 0;
+
+ if (fref < 1000000 || fref > 27000000)
+ cfreq = 0;
+
+ return (u32) cfreq;
+}
+
+u32 clk_get_pclk_div(void)
+{
+ return 1 + ((__raw_readl(LPC32XX_CLKPWR_HCLK_DIV) >> 2) & 0x1F);
+}
+
+static struct map_desc lpc32xx_io_desc[] __initdata = {
+ {
+ .virtual = IO_ADDRESS(LPC32XX_AHB0_START),
+ .pfn = __phys_to_pfn(LPC32XX_AHB0_START),
+ .length = LPC32XX_AHB0_SIZE,
+ .type = MT_DEVICE
+ },
+ {
+ .virtual = IO_ADDRESS(LPC32XX_AHB1_START),
+ .pfn = __phys_to_pfn(LPC32XX_AHB1_START),
+ .length = LPC32XX_AHB1_SIZE,
+ .type = MT_DEVICE
+ },
+ {
+ .virtual = IO_ADDRESS(LPC32XX_FABAPB_START),
+ .pfn = __phys_to_pfn(LPC32XX_FABAPB_START),
+ .length = LPC32XX_FABAPB_SIZE,
+ .type = MT_DEVICE
+ },
+ {
+ .virtual = IO_ADDRESS(LPC32XX_IRAM_BASE),
+ .pfn = __phys_to_pfn(LPC32XX_IRAM_BASE),
+ .length = (LPC32XX_IRAM_BANK_SIZE * 2),
+ .type = MT_DEVICE
+ },
+};
+
+void __init lpc32xx_map_io(void)
+{
+ iotable_init(lpc32xx_io_desc, ARRAY_SIZE(lpc32xx_io_desc));
+}
diff --git a/arch/arm/mach-lpc32xx/common.h b/arch/arm/mach-lpc32xx/common.h
new file mode 100644
index 0000000..f82211f
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/common.h
@@ -0,0 +1,73 @@
+/*
+ * arch/arm/mach-lpc32xx/common.h
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2009-2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __LPC32XX_COMMON_H
+#define __LPC32XX_COMMON_H
+
+#include <linux/platform_device.h>
+
+/*
+ * Arch specific platform device structures
+ */
+extern struct platform_device lpc32xx_watchdog_device;
+extern struct platform_device lpc32xx_i2c0_device;
+extern struct platform_device lpc32xx_i2c1_device;
+extern struct platform_device lpc32xx_i2c2_device;
+
+/*
+ * Other arch specific structures and functions
+ */
+extern struct sys_timer lpc32xx_timer;
+extern void __init lpc32xx_init_irq(void);
+extern void __init lpc32xx_map_io(void);
+extern void __init lpc32xx_serial_init(void);
+extern void __init lpc32xx_gpio_init(void);
+
+/*
+ * Structure used for setting up and querying the PLLS
+ */
+struct clk_pll_setup {
+ int analog_on;
+ int cco_bypass_b15;
+ int direct_output_b14;
+ int fdbk_div_ctrl_b13;
+ int pll_p;
+ int pll_n;
+ u32 pll_m;
+};
+
+extern int clk_is_sysclk_mainosc(void);
+extern u32 clk_check_pll_setup(u32 ifreq, struct clk_pll_setup *pllsetup);
+extern u32 clk_get_pllrate_from_reg(u32 inputclk, u32 regval);
+extern u32 clk_get_pclk_div(void);
+
+/*
+ * Returns the LPC32xx unique 128-bit chip ID
+ */
+extern void lpc32xx_get_uid(u32 devid[4]);
+
+extern void lpc32xx_watchdog_reset(void);
+extern u32 lpc32xx_return_iram_size(void);
+
+/*
+ * Pointers used for sizing and copying suspend function data
+ */
+extern int lpc32xx_sys_suspend(void);
+extern int lpc32xx_sys_suspend_sz;
+
+#endif
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 08/13] ARM: LPC32XX: Phytec 3250 platform support
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (6 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 07/13] ARM: LPC32XX: Misc support functions wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 09/13] ARM: LPC32XX: Arch config menu supoport and makefiles wellsk40 at gmail.com
` (4 subsequent siblings)
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Platform support file for the PHY3250 mach id
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/phy3250.c | 397 +++++++++++++++++++++++++++++++++++++++
1 files changed, 397 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
new file mode 100644
index 0000000..bc9a42d
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -0,0 +1,397 @@
+/*
+ * arch/arm/mach-lpc32xx/phy3250.c
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/dma-mapping.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/eeprom.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/clcd.h>
+#include <linux/amba/pl022.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+#include "common.h"
+
+/*
+ * Mapped GPIOLIB GPIOs
+ */
+#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
+#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define LED_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 1)
+
+/*
+ * AMBA LCD controller
+ */
+static struct clcd_panel conn_lcd_panel = {
+ .mode = {
+ .name = "QVGA portrait",
+ .refresh = 60,
+ .xres = 240,
+ .yres = 320,
+ .pixclock = 191828,
+ .left_margin = 22,
+ .right_margin = 11,
+ .upper_margin = 2,
+ .lower_margin = 1,
+ .hsync_len = 5,
+ .vsync_len = 2,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = (TIM2_IVS | TIM2_IHS),
+ .cntl = (CNTL_BGR | CNTL_LCDTFT | CNTL_LCDVCOMP(1) |
+ CNTL_LCDBPP16_565),
+ .bpp = 16,
+};
+#define PANEL_SIZE (3 * SZ_64K)
+
+static int lpc32xx_clcd_setup(struct clcd_fb *fb)
+{
+ dma_addr_t dma;
+
+ fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev,
+ PANEL_SIZE, &dma, GFP_KERNEL);
+ if (!fb->fb.screen_base) {
+ printk(KERN_ERR "CLCD: unable to map framebuffer\n");
+ return -ENOMEM;
+ }
+
+ fb->fb.fix.smem_start = dma;
+ fb->fb.fix.smem_len = PANEL_SIZE;
+ fb->panel = &conn_lcd_panel;
+
+ if (gpio_request(LCD_POWER_GPIO, "LCD power"))
+ printk(KERN_ERR "Error requesting gpio %u",
+ LCD_POWER_GPIO);
+ else if (gpio_direction_output(LCD_POWER_GPIO, 1))
+ printk(KERN_ERR "Error setting gpio %u to output",
+ LCD_POWER_GPIO);
+
+ if (gpio_request(BKL_POWER_GPIO, "LCD backlight power"))
+ printk(KERN_ERR "Error requesting gpio %u",
+ BKL_POWER_GPIO);
+ else if (gpio_direction_output(BKL_POWER_GPIO, 1))
+ printk(KERN_ERR "Error setting gpio %u to output",
+ BKL_POWER_GPIO);
+
+ return 0;
+}
+
+static int lpc32xx_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
+{
+ return dma_mmap_writecombine(&fb->dev->dev, vma,
+ fb->fb.screen_base, fb->fb.fix.smem_start,
+ fb->fb.fix.smem_len);
+}
+
+static void lpc32xx_clcd_remove(struct clcd_fb *fb)
+{
+ dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
+ fb->fb.screen_base, fb->fb.fix.smem_start);
+}
+
+/*
+ * On some early LCD modules (1307.0), the backlight logic is inverted.
+ * For those board variants, swap the disable and enable states for
+ * BKL_POWER_GPIO.
+*/
+static void clcd_disable(struct clcd_fb *fb)
+{
+ gpio_set_value(BKL_POWER_GPIO, 0);
+ gpio_set_value(LCD_POWER_GPIO, 0);
+}
+
+static void clcd_enable(struct clcd_fb *fb)
+{
+ gpio_set_value(BKL_POWER_GPIO, 1);
+ gpio_set_value(LCD_POWER_GPIO, 1);
+}
+
+static struct clcd_board lpc32xx_clcd_data = {
+ .name = "Phytec LCD",
+ .check = clcdfb_check,
+ .decode = clcdfb_decode,
+ .disable = clcd_disable,
+ .enable = clcd_enable,
+ .setup = lpc32xx_clcd_setup,
+ .mmap = lpc32xx_clcd_mmap,
+ .remove = lpc32xx_clcd_remove,
+};
+
+static struct amba_device lpc32xx_clcd_device = {
+ .dev = {
+ .coherent_dma_mask = ~0,
+ .init_name = "dev:clcd",
+ .platform_data = &lpc32xx_clcd_data,
+ },
+ .res = {
+ .start = LPC32XX_LCD_BASE,
+ .end = (LPC32XX_LCD_BASE + SZ_4K - 1),
+ .flags = IORESOURCE_MEM,
+ },
+ .dma_mask = ~0,
+ .irq = {IRQ_LPC32XX_LCD, NO_IRQ},
+};
+
+/*
+ * AMBA SSP (SPI)
+ */
+static void phy3250_spi_cs_set(u32 control)
+{
+ gpio_set_value(SPI0_CS_GPIO, (int) control);
+}
+
+static struct pl022_config_chip spi0_chip_info = {
+ .lbm = LOOPBACK_DISABLED,
+ .com_mode = INTERRUPT_TRANSFER,
+ .iface = SSP_INTERFACE_MOTOROLA_SPI,
+ .hierarchy = SSP_MASTER,
+ .slave_tx_disable = 0,
+ .endian_tx = SSP_TX_LSB,
+ .endian_rx = SSP_RX_LSB,
+ .data_size = SSP_DATA_BITS_8,
+ .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
+ .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
+ .clk_phase = SSP_CLK_FIRST_EDGE,
+ .clk_pol = SSP_CLK_POL_IDLE_LOW,
+ .ctrl_len = SSP_BITS_8,
+ .wait_state = SSP_MWIRE_WAIT_ZERO,
+ .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
+ .cs_control = phy3250_spi_cs_set,
+};
+
+static struct pl022_ssp_controller lpc32xx_ssp0_data = {
+ .bus_id = 0,
+ .num_chipselect = 1,
+ .enable_dma = 0,
+};
+
+static struct amba_device lpc32xx_ssp0_device = {
+ .dev = {
+ .coherent_dma_mask = ~0,
+ .init_name = "dev:ssp0",
+ .platform_data = &lpc32xx_ssp0_data,
+ },
+ .res = {
+ .start = LPC32XX_SSP0_BASE,
+ .end = (LPC32XX_SSP0_BASE + SZ_4K - 1),
+ .flags = IORESOURCE_MEM,
+ },
+ .dma_mask = ~0,
+ .irq = {IRQ_LPC32XX_SSP0, NO_IRQ},
+};
+
+/* AT25 driver registration */
+static int __init phy3250_spi_board_register(void)
+{
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+ static struct spi_board_info info[] = {
+ {
+ .modalias = "spidev",
+ .max_speed_hz = 5000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .controller_data = &spi0_chip_info,
+ },
+ };
+
+#else
+ static struct spi_eeprom eeprom = {
+ .name = "at25256a",
+ .byte_len = 0x8000,
+ .page_size = 64,
+ .flags = EE_ADDR2,
+ };
+
+ static struct spi_board_info info[] = {
+ {
+ .modalias = "at25",
+ .max_speed_hz = 5000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .platform_data = &eeprom,
+ .controller_data = &spi0_chip_info,
+ },
+ };
+#endif
+ return spi_register_board_info(info, ARRAY_SIZE(info));
+}
+arch_initcall(phy3250_spi_board_register);
+
+static struct i2c_board_info __initdata phy3250_i2c_board_info[] = {
+ {
+ I2C_BOARD_INFO("pcf8563", 0x51),
+ },
+};
+
+static struct gpio_led phy_leds[] = {
+ {
+ .name = "led0",
+ .gpio = LED_GPIO,
+ .active_low = 1,
+ .default_trigger = "heartbeat",
+ },
+};
+
+static struct gpio_led_platform_data led_data = {
+ .leds = phy_leds,
+ .num_leds = ARRAY_SIZE(phy_leds),
+};
+
+static struct platform_device lpc32xx_gpio_led_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev.platform_data = &led_data,
+};
+
+static struct platform_device *phy3250_devs[] __initdata = {
+ &lpc32xx_i2c0_device,
+ &lpc32xx_i2c1_device,
+ &lpc32xx_i2c2_device,
+ &lpc32xx_watchdog_device,
+ &lpc32xx_gpio_led_device,
+};
+
+static struct amba_device *amba_devs[] __initdata = {
+ &lpc32xx_clcd_device,
+ &lpc32xx_ssp0_device,
+};
+
+/*
+ * Board specific functions
+ */
+static void __init phy3250_board_init(void)
+{
+ u32 tmp;
+ int i;
+
+ lpc32xx_gpio_init();
+
+ /* Register GPIOs used on this board */
+ if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
+ printk(KERN_ERR "Error requesting gpio %u",
+ SPI0_CS_GPIO);
+ else if (gpio_direction_output(SPI0_CS_GPIO, 1))
+ printk(KERN_ERR "Error setting gpio %u to output",
+ SPI0_CS_GPIO);
+
+ /* Setup network interface for RMII mode */
+ tmp = __raw_readl(LPC32XX_CLKPWR_MACCLK_CTRL);
+ tmp &= ~LPC32XX_CLKPWR_MACCTRL_PINS_MSK;
+ tmp |= LPC32XX_CLKPWR_MACCTRL_USE_RMII_PINS;
+ __raw_writel(tmp, LPC32XX_CLKPWR_MACCLK_CTRL);
+
+ /* Setup SLC NAND controller muxing */
+ __raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
+ LPC32XX_CLKPWR_NAND_CLK_CTRL);
+
+ /* Setup LCD muxing to RGB565 */
+ tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) &
+ ~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK |
+ LPC32XX_CLKPWR_LCDCTRL_PSCALE_MSK);
+ tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16;
+ __raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL);
+
+ /* Set up I2C pull levels */
+ tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL);
+ tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE |
+ LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE;
+ __raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL);
+
+ /* Disable IrDA pulsing support on UART6 */
+ tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
+ tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
+ __raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
+
+ /* Enable DMA for I2S1 channel */
+ tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL);
+ tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA;
+ __raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL);
+
+ lpc32xx_serial_init();
+
+ /*
+ * AMBA peripheral clocks need to be enabled prior to AMBA device
+ * detection or a data fault will occur, so enable the clocks
+ * here. However, we don't want to enable them if the peripheral
+ * isn't included in the image
+ */
+#ifdef CONFIG_FB_ARMCLCD
+ tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
+ __raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
+ LPC32XX_CLKPWR_LCDCLK_CTRL);
+#endif
+#ifdef CONFIG_SPI_PL022
+ tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
+ __raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
+ LPC32XX_CLKPWR_SSP_CLK_CTRL);
+#endif
+
+ platform_add_devices(phy3250_devs, ARRAY_SIZE(phy3250_devs));
+ for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
+ struct amba_device *d = amba_devs[i];
+ amba_device_register(d, &iomem_resource);
+ }
+
+ /* Test clock needed for UDA1380 initial init */
+ __raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
+ LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN,
+ LPC32XX_CLKPWR_TEST_CLK_SEL);
+
+ i2c_register_board_info(0, phy3250_i2c_board_info,
+ ARRAY_SIZE(phy3250_i2c_board_info));
+}
+
+static int __init lpc32xx_display_uid(void)
+{
+ u32 uid[4];
+
+ lpc32xx_get_uid(uid);
+
+ printk(KERN_INFO "LPC32XX unique ID: %08x%08x%08x%08x\n",
+ uid[3], uid[2], uid[1], uid[0]);
+
+ return 1;
+}
+arch_initcall(lpc32xx_display_uid);
+
+MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller")
+ /* Maintainer: Kevin Wells, NXP Semiconductors */
+ .phys_io = LPC32XX_UART5_BASE,
+ .io_pg_offst = ((IO_ADDRESS(LPC32XX_UART5_BASE))>>18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = lpc32xx_map_io,
+ .init_irq = lpc32xx_init_irq,
+ .timer = &lpc32xx_timer,
+ .init_machine = phy3250_board_init,
+MACHINE_END
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 09/13] ARM: LPC32XX: Arch config menu supoport and makefiles
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (7 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 08/13] ARM: LPC32XX: Phytec 3250 platform support wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 10/13] ARM: LPC32XX: Default PHY3250 kernel config (ramdisk) wellsk40 at gmail.com
` (3 subsequent siblings)
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/Kconfig | 33 +++++++++++++++++++++++++++++++++
arch/arm/mach-lpc32xx/Makefile | 8 ++++++++
arch/arm/mach-lpc32xx/Makefile.boot | 4 ++++
3 files changed, 45 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-lpc32xx/Kconfig b/arch/arm/mach-lpc32xx/Kconfig
new file mode 100644
index 0000000..fde6635
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/Kconfig
@@ -0,0 +1,33 @@
+if ARCH_LPC32XX
+
+menu "Individual UART enable selections"
+
+config ARCH_LPC32XX_UART3_SELECT
+ bool "Add support for standard UART3"
+ help
+ Adds support for standard UART 3 when the 8250 serial support
+ is enabled.
+
+config ARCH_LPC32XX_UART4_SELECT
+ bool "Add support for standard UART4"
+ help
+ Adds support for standard UART 4 when the 8250 serial support
+ is enabled.
+
+config ARCH_LPC32XX_UART5_SELECT
+ bool "Add support for standard UART5"
+ default y
+ help
+ Adds support for standard UART 5 when the 8250 serial support
+ is enabled.
+
+config ARCH_LPC32XX_UART6_SELECT
+ bool "Add support for standard UART6"
+ help
+ Adds support for standard UART 6 when the 8250 serial support
+ is enabled.
+
+endmenu
+
+endif
+
diff --git a/arch/arm/mach-lpc32xx/Makefile b/arch/arm/mach-lpc32xx/Makefile
new file mode 100644
index 0000000..a5fc5d0
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/Makefile
@@ -0,0 +1,8 @@
+#
+# Makefile for the linux kernel.
+#
+
+obj-y := timer.o irq.o common.o serial.o clock.o
+obj-y += gpiolib.o pm.o suspend.o
+obj-y += phy3250.o
+
diff --git a/arch/arm/mach-lpc32xx/Makefile.boot b/arch/arm/mach-lpc32xx/Makefile.boot
new file mode 100644
index 0000000..b796b41
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/Makefile.boot
@@ -0,0 +1,4 @@
+ zreladdr-y := 0x80008000
+params_phys-y := 0x80000100
+initrd_phys-y := 0x82000000
+
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 10/13] ARM: LPC32XX: Default PHY3250 kernel config (ramdisk)
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (8 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 09/13] ARM: LPC32XX: Arch config menu supoport and makefiles wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 11/13] ARM: Add support for the LPC32XX arch wellsk40 at gmail.com
` (2 subsequent siblings)
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/configs/phy3250_defconfig | 1084 ++++++++++++++++++++++++++++++++++++
1 files changed, 1084 insertions(+), 0 deletions(-)
diff --git a/arch/arm/configs/phy3250_defconfig b/arch/arm/configs/phy3250_defconfig
new file mode 100644
index 0000000..2c0145c
--- /dev/null
+++ b/arch/arm/configs/phy3250_defconfig
@@ -0,0 +1,1084 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.33-rc6
+# Mon Feb 8 13:45:54 2010
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
+# CONFIG_KERNEL_LZO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_LZO is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_SPIN_UNLOCK is not set
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_READ_UNLOCK is not set
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_WRITE_UNLOCK is not set
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
+CONFIG_FREEZER=y
+
+#
+# System Type
+#
+CONFIG_MMU=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_NOMADIK is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+CONFIG_ARCH_LPC32XX=y
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_U8500 is not set
+
+#
+# Individual UART enable selections
+#
+# CONFIG_ARCH_LPC32XX_UART3_SELECT is not set
+# CONFIG_ARCH_LPC32XX_UART4_SELECT is not set
+CONFIG_ARCH_LPC32XX_UART5_SELECT=y
+# CONFIG_ARCH_LPC32XX_UART6_SELECT is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_ARM926T=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5TJ=y
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_V4WB=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+CONFIG_ARM_AMBA=y
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
+CONFIG_PREEMPT=y
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="console=tty0 console=ttyS0,115200n81 root=/dev/ram0 init=/sbin/init"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_IDLE_GOV_MENU=y
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+CONFIG_VFP=y
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+CONFIG_BINFMT_AOUT=y
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
+# CONFIG_PM_RUNTIME is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+# CONFIG_NET is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_MTD is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=y
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=1
+CONFIG_BLK_DEV_RAM_SIZE=16384
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_MG_DISK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_AD525X_DPOT is not set
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_TI_DAC7512 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+CONFIG_EEPROM_AT25=y
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_AMBA_PL010 is not set
+# CONFIG_SERIAL_AMBA_PL011 is not set
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PNX=y
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_PL022=y
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+# CONFIG_GPIO_PL061 is not set
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+# CONFIG_GPIO_ADP5588 is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_PNX4008_WATCHDOG=y
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MFD_88PM8607 is not set
+# CONFIG_AB4500_CORE is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+CONFIG_FB_ARMCLCD=y
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP3944 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_BD2802 is not set
+# CONFIG_LEDS_LT3593 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+# CONFIG_LEDS_TRIGGER_TIMER is not set
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
+# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+# CONFIG_FILE_LOCKING is not set
+CONFIG_FSNOTIFY=y
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_ARM_UNWIND is not set
+CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_ERRORS=y
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+# CONFIG_OC_ETM is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+CONFIG_CRYPTO_AES=y
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=y
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=y
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 11/13] ARM: Add support for the LPC32XX arch
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (9 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 10/13] ARM: LPC32XX: Default PHY3250 kernel config (ramdisk) wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 12/13] i2c: " wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 13/13] WATCHDOG: " wellsk40 at gmail.com
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Add LPC32XX support in arch/arm/Kconfig and arch/arm/Makefile
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/Kconfig | 15 +++++++++++++++
arch/arm/Makefile | 1 +
2 files changed, 16 insertions(+), 0 deletions(-)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index e4150f4..922dfb0 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -572,6 +572,19 @@ config ARCH_NUC93X
Support for Nuvoton (Winbond logic dept.) NUC93X MCU,The NUC93X is a
low-power and high performance MPEG-4/JPEG multimedia controller chip.
+config ARCH_LPC32XX
+ bool "NXP LPC32XX"
+ select CPU_ARM926T
+ select ARCH_REQUIRE_GPIOLIB
+ select HAVE_IDE
+ select ARM_AMBA
+ select USB_ARCH_HAS_OHCI
+ select COMMON_CLKDEV
+ select GENERIC_TIME
+ select GENERIC_CLOCKEVENTS
+ help
+ Support for the NXP LPC32XX family of processors
+
config ARCH_PNX4008
bool "Philips Nexperia PNX4008 Mobile"
select CPU_ARM926T
@@ -809,6 +822,8 @@ source "arch/arm/mach-lh7a40x/Kconfig"
source "arch/arm/mach-loki/Kconfig"
+source "arch/arm/mach-lpc32xx/Kconfig"
+
source "arch/arm/mach-msm/Kconfig"
source "arch/arm/mach-mv78xx0/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index e471a96..181611c 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -139,6 +139,7 @@ machine-$(CONFIG_ARCH_KS8695) := ks8695
machine-$(CONFIG_ARCH_L7200) := l7200
machine-$(CONFIG_ARCH_LH7A40X) := lh7a40x
machine-$(CONFIG_ARCH_LOKI) := loki
+machine-$(CONFIG_ARCH_LPC32XX) := lpc32xx
machine-$(CONFIG_ARCH_MMP) := mmp
machine-$(CONFIG_ARCH_MSM) := msm
machine-$(CONFIG_ARCH_MV78XX0) := mv78xx0
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 12/13] i2c: Add support for the LPC32XX arch
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (10 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 11/13] ARM: Add support for the LPC32XX arch wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 13/13] WATCHDOG: " wellsk40 at gmail.com
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Allow the i2c-pnx driver to be reused with the LPC32xx arch.
Changed menu title to include NXP devices
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
drivers/i2c/busses/Kconfig | 4 ++--
1 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 02afe89..44c5fd7 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -474,8 +474,8 @@ config I2C_PASEMI
Supports the PA Semi PWRficient on-chip SMBus interfaces.
config I2C_PNX
- tristate "I2C bus support for Philips PNX targets"
- depends on ARCH_PNX4008
+ tristate "I2C bus support for Philips/NXP devices"
+ depends on ARCH_PNX4008 || ARCH_LPC32XX
help
This driver supports the Philips IP3204 I2C IP block master and/or
slave controller
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 13/13] WATCHDOG: Add support for the LPC32XX arch
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
` (11 preceding siblings ...)
2010-02-19 23:26 ` [PATCH 12/13] i2c: " wellsk40 at gmail.com
@ 2010-02-19 23:26 ` wellsk40 at gmail.com
12 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-19 23:26 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Allow the pnx4408 watchdog driver to be reused with the
LPC32xx arch. Changed menu title to include the LCP32XX
device.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
drivers/watchdog/Kconfig | 6 +++---
1 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 713b1ce..b882e09 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -205,11 +205,11 @@ config OMAP_WATCHDOG
here to enable the OMAP1610/OMAP1710/OMAP2420/OMAP3430 watchdog timer.
config PNX4008_WATCHDOG
- tristate "PNX4008 Watchdog"
- depends on ARCH_PNX4008
+ tristate "PNX4008/LPC32XX Watchdog"
+ depends on ARCH_PNX4008 || ARCH_LPC32XX
help
Say Y here if to include support for the watchdog timer
- in the PNX4008 processor.
+ in the PNX4008 or LPC32XX processors.
This driver can be built as a module by choosing M. The module
will be called pnx4008_wdt.
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH 01/13] ARM: LPC32XX: Initial architecture header files
2010-02-19 23:25 ` [PATCH 01/13] ARM: LPC32XX: Initial architecture header files wellsk40 at gmail.com
@ 2010-02-20 16:12 ` Uwe Kleine-König
[not found] ` <a08234131002201112x66a595c4j235bf1a31aef4f92@mail.gmail.com>
0 siblings, 1 reply; 23+ messages in thread
From: Uwe Kleine-König @ 2010-02-20 16:12 UTC (permalink / raw)
To: linux-arm-kernel
Hey Kevin,
> +/*
> + * Note!
> + * Muxed GP pins need to be setup to the GP state in the board level
> + * code prior to using this driver.
This is done by the imx machines, too, and I wonder if it's worth to try
to get rid of that or at least let the gpio_direction_... functions fail
if the pin isn't muxed as gpio. Thoughts?
I didn't check the alternative functionalities for the gpios on lpc32xx,
but what happens if any gpio is requested and the direction configured?
Does it interfer with system functions? (E.g. if a pin is used in a
dedicated say i2c function, does it make the i2c driver non-functional
if I do gpio_direction_output(i2cpin, 1)?)
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 03/13] ARM: LPC32XX: Clock driver
2010-02-19 23:25 ` [PATCH 03/13] ARM: LPC32XX: Clock driver wellsk40 at gmail.com
@ 2010-02-20 16:33 ` Russell King - ARM Linux
2010-02-23 21:28 ` Kevin Wells
0 siblings, 1 reply; 23+ messages in thread
From: Russell King - ARM Linux @ 2010-02-20 16:33 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Feb 19, 2010 at 03:25:59PM -0800, wellsk40 at gmail.com wrote:
> +static u32 local_return_parent_rate(struct clk *clk)
> +{
> + /*
> + * If a clock has a rate of 0, then it inherits it's parent
> + * clock rate
> + */
> + if (clk->rate == 0)
> + return local_return_parent_rate(clk->parent);
Does this really need to be recursive?
while (clk->rate == 0)
clk = clk->parent;
return clk->rate;
?
> +static u32 mmc_get_rate(struct clk *clk)
> +{
> + u32 div, tmp, rate;
> +
> + div = __raw_readl(LPC32XX_CLKPWR_MS_CTRL);
> + tmp = div & LPC32XX_CLKPWR_MSCARD_SDCARD_EN;
> +
> + if (!tmp)
> + return 0;
There's no requirement to return a rate of zero if the clock is not enabled.
In fact, it's something that should be avoided because it prevents querying
the rate you'll get before enabling the clock (which might affect whether
you decide to enable it.)
> +static void local_clk_disable(struct clk *clk)
> +{
> + WARN_ON(clk->usecount == 0);
> +
> + /* Don't attempt to disable clock if it has no users */
> + if (clk->usecount > 0) {
> + clk->usecount--;
> +
> + /* Only disable clock when it has no more users */
> + if ((clk->usecount == 0) && (clk->enable))
> + clk->enable(clk, 0);
> +
> + /* Check parent clocks, they may need to be disabled too */
> + if (clk->parent)
> + local_clk_disable(clk->parent);
This is not a good idea if you ever support clock reparenting - it's
much better to have the parent enabled when the usecount changes from
0 to 1, and disabled when you move from 1 to 0 - otherwise you'll
have to call local_clk_disable() and local_clk_enable() multiple times
when you reparent.
> +unsigned long clk_get_rate(struct clk *clk)
> +{
> + unsigned long rate;
> +
> + clk_lock();
> + rate = (clk->get_rate)(clk);
parens aren't required.
> + if (clk->set_rate) {
> + clk_lock();
> + ret = (clk->set_rate)(clk, rate);
Ditto.
> +/*
> + * clk_round_rate - adjust a rate to the exact rate a clock can provide
> + */
> +long clk_round_rate(struct clk *clk, unsigned long rate)
> +{
> + int ret;
> +
> + /* Use set_rate to try to adjust the rate if it supports it */
> + ret = clk_set_rate(clk, rate);
This is definitely wrong. round_rate() is supposed to return the rate
which the clock will give you for the rate you're asking for _without_
setting it.
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 06/13] ARM: LPC32XX: Serial support code
2010-02-19 23:26 ` [PATCH 06/13] ARM: LPC32XX: Serial support code wellsk40 at gmail.com
@ 2010-02-20 16:34 ` Russell King - ARM Linux
0 siblings, 0 replies; 23+ messages in thread
From: Russell King - ARM Linux @ 2010-02-20 16:34 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Feb 19, 2010 at 03:26:02PM -0800, wellsk40 at gmail.com wrote:
> +#include <linux/kernel.h>
> +#include <linux/types.h>
> +#include <linux/serial.h>
> +#include <linux/serial_core.h>
> +#include <linux/serial_reg.h>
> +#include <linux/serial_8250.h>
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +
> +#include <mach/hardware.h>
> +#include <mach/platform.h>
> +#include <mach/io.h>
mach/io.h is not required.
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 01/13] ARM: LPC32XX: Initial architecture header files
[not found] ` <a08234131002201112x66a595c4j235bf1a31aef4f92@mail.gmail.com>
@ 2010-02-20 19:14 ` Kevin Wells
2010-02-20 19:17 ` Kevin Wells
1 sibling, 0 replies; 23+ messages in thread
From: Kevin Wells @ 2010-02-20 19:14 UTC (permalink / raw)
To: linux-arm-kernel
2010/2/20 Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Hey Kevin,
>
> > +/*
> > + * Note!
> > + * Muxed GP pins need to be setup to the GP state in the board level
> > + * code prior to using this driver.
> This is done by the imx machines, too, and I wonder if it's worth to try
> to get rid of that or at least let the gpio_direction_... functions fail
> if the pin isn't muxed as gpio. Thoughts?
>
> HI Uwe,
In the current function of the driver, the assumption is that if an out pin
is used, it has already been muxed correctly, so requesting an output
for a pin not muxed as a GPI/O will work fine and even setting it's pin
level will work, but the level won't appear on the external pin. If
something decides to switch the mux after that state is programmed,
then the currently programmed output level will show up on that pin.
For state muxing, I would prefer to not have the GPIO driver change an
existing mux state to make a GPIO work. I don't return an error now
when a output state is used and is not muxed for an output state. But
its painless to add this.
GPI pins and GPIO pins configured as inputs always work regardless
of the muxed pin state and would never need to have a fail check, its
basically a raw pin state read.
I didn't check the alternative functionalities for the gpios on lpc32xx,
> but what happens if any gpio is requested and the direction configured?
> Does it interfer with system functions? (E.g. if a pin is used in a
> dedicated say i2c function, does it make the i2c driver non-functional
> if I do gpio_direction_output(i2cpin, 1)?)
>
>
Setting a GPIO direction or output state will not effect a peripheral pin
(on this part) when muxed for the peripheral. (ie, setting a GPIO to output
and switching it to low when its shared with a UART pin and the mux is
setup for UART).
thanks,
Kevin
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20100220/24c3bd02/attachment-0001.htm>
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 01/13] ARM: LPC32XX: Initial architecture header files
[not found] ` <a08234131002201112x66a595c4j235bf1a31aef4f92@mail.gmail.com>
2010-02-20 19:14 ` Kevin Wells
@ 2010-02-20 19:17 ` Kevin Wells
2010-02-22 21:41 ` Kevin Wells
1 sibling, 1 reply; 23+ messages in thread
From: Kevin Wells @ 2010-02-20 19:17 UTC (permalink / raw)
To: linux-arm-kernel
2010/2/20 Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
>
> Hey Kevin,
>
> > +/*
> > + * Note!
> > + * Muxed GP pins need to be setup to the GP state in the board level
> > + * code prior to using this driver.
> This is done by the imx machines, too, and I wonder if it's worth to try
> to get rid of that or at least let the gpio_direction_... functions fail
> if the pin isn't muxed as gpio. ?Thoughts?
>
HI Uwe,
In the current function of the driver, the assumption is that if an out pin
is used, it has already been muxed correctly, so requesting an output
for a pin not muxed as a GPI/O will work fine and even setting it's pin
level will work, but the level won't appear on the external pin. If
something decides to switch the mux after that state is programmed,
then the currently programmed output level will show up on that pin.
For state muxing, I would prefer to not have the GPIO driver change an
existing mux state to make a GPIO work. I don't return an error now
when a output state is used and is not muxed for an output state. But
its painless to add this.
GPI pins and GPIO pins configured as inputs always work regardless
of the muxed pin state and would never need to have a fail check, its
basically a raw pin state read.
> I didn't check the alternative functionalities for the gpios on lpc32xx,
> but what happens if any gpio is requested and the direction configured?
> Does it interfer with system functions? ?(E.g. if a pin is used in a
> dedicated say i2c function, does it make the i2c driver non-functional
> if I do gpio_direction_output(i2cpin, 1)?)
>
Setting a GPIO direction or output state will not effect a peripheral pin
(on this part) when muxed for the peripheral. (ie, setting a GPIO to output
and switching it to low when its shared with a UART pin and the mux is
setup for UART).
thanks,
Kevin
> Best regards
> Uwe
>
> --
> Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? | Uwe Kleine-K?nig ? ? ? ? ? ?|
> Industrial Linux Solutions ? ? ? ? ? ? ? ? | http://www.pengutronix.de/ ?|
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 01/13] ARM: LPC32XX: Initial architecture header files
2010-02-20 19:17 ` Kevin Wells
@ 2010-02-22 21:41 ` Kevin Wells
2010-02-23 8:02 ` Uwe Kleine-König
0 siblings, 1 reply; 23+ messages in thread
From: Kevin Wells @ 2010-02-22 21:41 UTC (permalink / raw)
To: linux-arm-kernel
Hi Uwe,
I'm going to add the pin mux check to a future patch release.
It's a nice feature and may save some GPIO pin issues down
the road, but respectfully, I want to focus on getting the
release out without adding more changes & features at the
moment. I'll add this capbility in with a new pinmux driver
in the future.
thanks,
Kevin
> 2010/2/20 Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
> >
> > Hey Kevin,
> >
> > > +/*
> > > + * Note!
> > > + * Muxed GP pins need to be setup to the GP state in the board level
> > > + * code prior to using this driver.
> > This is done by the imx machines, too, and I wonder if it's worth to try
> > to get rid of that or at least let the gpio_direction_... functions fail
> > if the pin isn't muxed as gpio. ?Thoughts?
> >
> HI Uwe,
>
> In the current function of the driver, the assumption is that if an out
> pin
> is used, it has already been muxed correctly, so requesting an output
> for a pin not muxed as a GPI/O will work fine and even setting it's pin
> level will work, but the level won't appear on the external pin. If
> something decides to switch the mux after that state is programmed,
> then the currently programmed output level will show up on that pin.
>
> For state muxing, I would prefer to not have the GPIO driver change an
> existing mux state to make a GPIO work. I don't return an error now
> when a output state is used and is not muxed for an output state. But
> its painless to add this.
>
> GPI pins and GPIO pins configured as inputs always work regardless
> of the muxed pin state and would never need to have a fail check, its
> basically a raw pin state read.
>
> > I didn't check the alternative functionalities for the gpios on lpc32xx,
> > but what happens if any gpio is requested and the direction configured?
> > Does it interfer with system functions? ?(E.g. if a pin is used in a
> > dedicated say i2c function, does it make the i2c driver non-functional
> > if I do gpio_direction_output(i2cpin, 1)?)
> >
>
> Setting a GPIO direction or output state will not effect a peripheral pin
> (on this part) when muxed for the peripheral. (ie, setting a GPIO to
> output
> and switching it to low when its shared with a UART pin and the mux is
> setup for UART).
>
> thanks,
> Kevin
>
> > Best regards
> > Uwe
> >
> > --
> > Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? | Uwe Kleine-K?nig
> ?|
> > Industrial Linux Solutions ? ? ? ? ? ? ? ? | http://www.pengutronix.de/
> ?|
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 01/13] ARM: LPC32XX: Initial architecture header files
2010-02-22 21:41 ` Kevin Wells
@ 2010-02-23 8:02 ` Uwe Kleine-König
0 siblings, 0 replies; 23+ messages in thread
From: Uwe Kleine-König @ 2010-02-23 8:02 UTC (permalink / raw)
To: linux-arm-kernel
Hi Kevin,
On Mon, Feb 22, 2010 at 10:41:01PM +0100, Kevin Wells wrote:
> I'm going to add the pin mux check to a future patch release.
> It's a nice feature and may save some GPIO pin issues down
> the road, but respectfully, I want to focus on getting the
> release out without adding more changes & features at the
> moment. I'll add this capbility in with a new pinmux driver
> in the future.
OK for me.
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 03/13] ARM: LPC32XX: Clock driver
2010-02-20 16:33 ` Russell King - ARM Linux
@ 2010-02-23 21:28 ` Kevin Wells
0 siblings, 0 replies; 23+ messages in thread
From: Kevin Wells @ 2010-02-23 21:28 UTC (permalink / raw)
To: linux-arm-kernel
Hi Russell,
Thanks much for your response on this.
Does it make sense to repost the complete patchset or just the diffs
of the changed files? (clock.h and clock.c).
>
> There's no requirement to return a rate of zero if the clock is not
> enabled.
> In fact, it's something that should be avoided because it prevents
> querying
> the rate you'll get before enabling the clock (which might affect whether
> you decide to enable it.)
>
Alright, this reduces some checks. I've also made changes to set_rate
functions to allow clock rate changes without the clock being enabled
or changing the current clock enable state.
thanks,
Kevin
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 08/13] ARM: LPC32XX: Phytec 3250 platform support
2010-02-26 23:53 LPC32XX architecture files (updated v5) wellsk40 at gmail.com
@ 2010-02-26 23:53 ` wellsk40 at gmail.com
0 siblings, 0 replies; 23+ messages in thread
From: wellsk40 at gmail.com @ 2010-02-26 23:53 UTC (permalink / raw)
To: linux-arm-kernel
From: Kevin Wells <wellsk40@gmail.com>
Platform support file for the PHY3250 mach id
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
---
arch/arm/mach-lpc32xx/phy3250.c | 397 +++++++++++++++++++++++++++++++++++++++
1 files changed, 397 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-lpc32xx/phy3250.c
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
new file mode 100644
index 0000000..bc9a42d
--- /dev/null
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -0,0 +1,397 @@
+/*
+ * arch/arm/mach-lpc32xx/phy3250.c
+ *
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/dma-mapping.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/eeprom.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/clcd.h>
+#include <linux/amba/pl022.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/hardware.h>
+#include <mach/platform.h>
+#include "common.h"
+
+/*
+ * Mapped GPIOLIB GPIOs
+ */
+#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
+#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define LED_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 1)
+
+/*
+ * AMBA LCD controller
+ */
+static struct clcd_panel conn_lcd_panel = {
+ .mode = {
+ .name = "QVGA portrait",
+ .refresh = 60,
+ .xres = 240,
+ .yres = 320,
+ .pixclock = 191828,
+ .left_margin = 22,
+ .right_margin = 11,
+ .upper_margin = 2,
+ .lower_margin = 1,
+ .hsync_len = 5,
+ .vsync_len = 2,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = (TIM2_IVS | TIM2_IHS),
+ .cntl = (CNTL_BGR | CNTL_LCDTFT | CNTL_LCDVCOMP(1) |
+ CNTL_LCDBPP16_565),
+ .bpp = 16,
+};
+#define PANEL_SIZE (3 * SZ_64K)
+
+static int lpc32xx_clcd_setup(struct clcd_fb *fb)
+{
+ dma_addr_t dma;
+
+ fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev,
+ PANEL_SIZE, &dma, GFP_KERNEL);
+ if (!fb->fb.screen_base) {
+ printk(KERN_ERR "CLCD: unable to map framebuffer\n");
+ return -ENOMEM;
+ }
+
+ fb->fb.fix.smem_start = dma;
+ fb->fb.fix.smem_len = PANEL_SIZE;
+ fb->panel = &conn_lcd_panel;
+
+ if (gpio_request(LCD_POWER_GPIO, "LCD power"))
+ printk(KERN_ERR "Error requesting gpio %u",
+ LCD_POWER_GPIO);
+ else if (gpio_direction_output(LCD_POWER_GPIO, 1))
+ printk(KERN_ERR "Error setting gpio %u to output",
+ LCD_POWER_GPIO);
+
+ if (gpio_request(BKL_POWER_GPIO, "LCD backlight power"))
+ printk(KERN_ERR "Error requesting gpio %u",
+ BKL_POWER_GPIO);
+ else if (gpio_direction_output(BKL_POWER_GPIO, 1))
+ printk(KERN_ERR "Error setting gpio %u to output",
+ BKL_POWER_GPIO);
+
+ return 0;
+}
+
+static int lpc32xx_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
+{
+ return dma_mmap_writecombine(&fb->dev->dev, vma,
+ fb->fb.screen_base, fb->fb.fix.smem_start,
+ fb->fb.fix.smem_len);
+}
+
+static void lpc32xx_clcd_remove(struct clcd_fb *fb)
+{
+ dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
+ fb->fb.screen_base, fb->fb.fix.smem_start);
+}
+
+/*
+ * On some early LCD modules (1307.0), the backlight logic is inverted.
+ * For those board variants, swap the disable and enable states for
+ * BKL_POWER_GPIO.
+*/
+static void clcd_disable(struct clcd_fb *fb)
+{
+ gpio_set_value(BKL_POWER_GPIO, 0);
+ gpio_set_value(LCD_POWER_GPIO, 0);
+}
+
+static void clcd_enable(struct clcd_fb *fb)
+{
+ gpio_set_value(BKL_POWER_GPIO, 1);
+ gpio_set_value(LCD_POWER_GPIO, 1);
+}
+
+static struct clcd_board lpc32xx_clcd_data = {
+ .name = "Phytec LCD",
+ .check = clcdfb_check,
+ .decode = clcdfb_decode,
+ .disable = clcd_disable,
+ .enable = clcd_enable,
+ .setup = lpc32xx_clcd_setup,
+ .mmap = lpc32xx_clcd_mmap,
+ .remove = lpc32xx_clcd_remove,
+};
+
+static struct amba_device lpc32xx_clcd_device = {
+ .dev = {
+ .coherent_dma_mask = ~0,
+ .init_name = "dev:clcd",
+ .platform_data = &lpc32xx_clcd_data,
+ },
+ .res = {
+ .start = LPC32XX_LCD_BASE,
+ .end = (LPC32XX_LCD_BASE + SZ_4K - 1),
+ .flags = IORESOURCE_MEM,
+ },
+ .dma_mask = ~0,
+ .irq = {IRQ_LPC32XX_LCD, NO_IRQ},
+};
+
+/*
+ * AMBA SSP (SPI)
+ */
+static void phy3250_spi_cs_set(u32 control)
+{
+ gpio_set_value(SPI0_CS_GPIO, (int) control);
+}
+
+static struct pl022_config_chip spi0_chip_info = {
+ .lbm = LOOPBACK_DISABLED,
+ .com_mode = INTERRUPT_TRANSFER,
+ .iface = SSP_INTERFACE_MOTOROLA_SPI,
+ .hierarchy = SSP_MASTER,
+ .slave_tx_disable = 0,
+ .endian_tx = SSP_TX_LSB,
+ .endian_rx = SSP_RX_LSB,
+ .data_size = SSP_DATA_BITS_8,
+ .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
+ .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
+ .clk_phase = SSP_CLK_FIRST_EDGE,
+ .clk_pol = SSP_CLK_POL_IDLE_LOW,
+ .ctrl_len = SSP_BITS_8,
+ .wait_state = SSP_MWIRE_WAIT_ZERO,
+ .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
+ .cs_control = phy3250_spi_cs_set,
+};
+
+static struct pl022_ssp_controller lpc32xx_ssp0_data = {
+ .bus_id = 0,
+ .num_chipselect = 1,
+ .enable_dma = 0,
+};
+
+static struct amba_device lpc32xx_ssp0_device = {
+ .dev = {
+ .coherent_dma_mask = ~0,
+ .init_name = "dev:ssp0",
+ .platform_data = &lpc32xx_ssp0_data,
+ },
+ .res = {
+ .start = LPC32XX_SSP0_BASE,
+ .end = (LPC32XX_SSP0_BASE + SZ_4K - 1),
+ .flags = IORESOURCE_MEM,
+ },
+ .dma_mask = ~0,
+ .irq = {IRQ_LPC32XX_SSP0, NO_IRQ},
+};
+
+/* AT25 driver registration */
+static int __init phy3250_spi_board_register(void)
+{
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+ static struct spi_board_info info[] = {
+ {
+ .modalias = "spidev",
+ .max_speed_hz = 5000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .controller_data = &spi0_chip_info,
+ },
+ };
+
+#else
+ static struct spi_eeprom eeprom = {
+ .name = "at25256a",
+ .byte_len = 0x8000,
+ .page_size = 64,
+ .flags = EE_ADDR2,
+ };
+
+ static struct spi_board_info info[] = {
+ {
+ .modalias = "at25",
+ .max_speed_hz = 5000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .platform_data = &eeprom,
+ .controller_data = &spi0_chip_info,
+ },
+ };
+#endif
+ return spi_register_board_info(info, ARRAY_SIZE(info));
+}
+arch_initcall(phy3250_spi_board_register);
+
+static struct i2c_board_info __initdata phy3250_i2c_board_info[] = {
+ {
+ I2C_BOARD_INFO("pcf8563", 0x51),
+ },
+};
+
+static struct gpio_led phy_leds[] = {
+ {
+ .name = "led0",
+ .gpio = LED_GPIO,
+ .active_low = 1,
+ .default_trigger = "heartbeat",
+ },
+};
+
+static struct gpio_led_platform_data led_data = {
+ .leds = phy_leds,
+ .num_leds = ARRAY_SIZE(phy_leds),
+};
+
+static struct platform_device lpc32xx_gpio_led_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev.platform_data = &led_data,
+};
+
+static struct platform_device *phy3250_devs[] __initdata = {
+ &lpc32xx_i2c0_device,
+ &lpc32xx_i2c1_device,
+ &lpc32xx_i2c2_device,
+ &lpc32xx_watchdog_device,
+ &lpc32xx_gpio_led_device,
+};
+
+static struct amba_device *amba_devs[] __initdata = {
+ &lpc32xx_clcd_device,
+ &lpc32xx_ssp0_device,
+};
+
+/*
+ * Board specific functions
+ */
+static void __init phy3250_board_init(void)
+{
+ u32 tmp;
+ int i;
+
+ lpc32xx_gpio_init();
+
+ /* Register GPIOs used on this board */
+ if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
+ printk(KERN_ERR "Error requesting gpio %u",
+ SPI0_CS_GPIO);
+ else if (gpio_direction_output(SPI0_CS_GPIO, 1))
+ printk(KERN_ERR "Error setting gpio %u to output",
+ SPI0_CS_GPIO);
+
+ /* Setup network interface for RMII mode */
+ tmp = __raw_readl(LPC32XX_CLKPWR_MACCLK_CTRL);
+ tmp &= ~LPC32XX_CLKPWR_MACCTRL_PINS_MSK;
+ tmp |= LPC32XX_CLKPWR_MACCTRL_USE_RMII_PINS;
+ __raw_writel(tmp, LPC32XX_CLKPWR_MACCLK_CTRL);
+
+ /* Setup SLC NAND controller muxing */
+ __raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
+ LPC32XX_CLKPWR_NAND_CLK_CTRL);
+
+ /* Setup LCD muxing to RGB565 */
+ tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) &
+ ~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK |
+ LPC32XX_CLKPWR_LCDCTRL_PSCALE_MSK);
+ tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16;
+ __raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL);
+
+ /* Set up I2C pull levels */
+ tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL);
+ tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE |
+ LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE;
+ __raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL);
+
+ /* Disable IrDA pulsing support on UART6 */
+ tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
+ tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
+ __raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
+
+ /* Enable DMA for I2S1 channel */
+ tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL);
+ tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA;
+ __raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL);
+
+ lpc32xx_serial_init();
+
+ /*
+ * AMBA peripheral clocks need to be enabled prior to AMBA device
+ * detection or a data fault will occur, so enable the clocks
+ * here. However, we don't want to enable them if the peripheral
+ * isn't included in the image
+ */
+#ifdef CONFIG_FB_ARMCLCD
+ tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
+ __raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
+ LPC32XX_CLKPWR_LCDCLK_CTRL);
+#endif
+#ifdef CONFIG_SPI_PL022
+ tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
+ __raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
+ LPC32XX_CLKPWR_SSP_CLK_CTRL);
+#endif
+
+ platform_add_devices(phy3250_devs, ARRAY_SIZE(phy3250_devs));
+ for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
+ struct amba_device *d = amba_devs[i];
+ amba_device_register(d, &iomem_resource);
+ }
+
+ /* Test clock needed for UDA1380 initial init */
+ __raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
+ LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN,
+ LPC32XX_CLKPWR_TEST_CLK_SEL);
+
+ i2c_register_board_info(0, phy3250_i2c_board_info,
+ ARRAY_SIZE(phy3250_i2c_board_info));
+}
+
+static int __init lpc32xx_display_uid(void)
+{
+ u32 uid[4];
+
+ lpc32xx_get_uid(uid);
+
+ printk(KERN_INFO "LPC32XX unique ID: %08x%08x%08x%08x\n",
+ uid[3], uid[2], uid[1], uid[0]);
+
+ return 1;
+}
+arch_initcall(lpc32xx_display_uid);
+
+MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller")
+ /* Maintainer: Kevin Wells, NXP Semiconductors */
+ .phys_io = LPC32XX_UART5_BASE,
+ .io_pg_offst = ((IO_ADDRESS(LPC32XX_UART5_BASE))>>18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = lpc32xx_map_io,
+ .init_irq = lpc32xx_init_irq,
+ .timer = &lpc32xx_timer,
+ .init_machine = phy3250_board_init,
+MACHINE_END
--
1.6.6
^ permalink raw reply related [flat|nested] 23+ messages in thread
end of thread, other threads:[~2010-02-26 23:53 UTC | newest]
Thread overview: 23+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-02-19 23:25 LPC32XX architecture files (updated v4) wellsk40 at gmail.com
2010-02-19 23:25 ` [PATCH 01/13] ARM: LPC32XX: Initial architecture header files wellsk40 at gmail.com
2010-02-20 16:12 ` Uwe Kleine-König
[not found] ` <a08234131002201112x66a595c4j235bf1a31aef4f92@mail.gmail.com>
2010-02-20 19:14 ` Kevin Wells
2010-02-20 19:17 ` Kevin Wells
2010-02-22 21:41 ` Kevin Wells
2010-02-23 8:02 ` Uwe Kleine-König
2010-02-19 23:25 ` [PATCH 02/13] ARM: LPC32XX: Debug and IRQ macros wellsk40 at gmail.com
2010-02-19 23:25 ` [PATCH 03/13] ARM: LPC32XX: Clock driver wellsk40 at gmail.com
2010-02-20 16:33 ` Russell King - ARM Linux
2010-02-23 21:28 ` Kevin Wells
2010-02-19 23:26 ` [PATCH 04/13] ARM: LPC32XX: GPIO, timer, and IRQ drivers wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 05/13] ARM: LPC32XX: System suspend support wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 06/13] ARM: LPC32XX: Serial support code wellsk40 at gmail.com
2010-02-20 16:34 ` Russell King - ARM Linux
2010-02-19 23:26 ` [PATCH 07/13] ARM: LPC32XX: Misc support functions wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 08/13] ARM: LPC32XX: Phytec 3250 platform support wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 09/13] ARM: LPC32XX: Arch config menu supoport and makefiles wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 10/13] ARM: LPC32XX: Default PHY3250 kernel config (ramdisk) wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 11/13] ARM: Add support for the LPC32XX arch wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 12/13] i2c: " wellsk40 at gmail.com
2010-02-19 23:26 ` [PATCH 13/13] WATCHDOG: " wellsk40 at gmail.com
-- strict thread matches above, loose matches on Subject: below --
2010-02-26 23:53 LPC32XX architecture files (updated v5) wellsk40 at gmail.com
2010-02-26 23:53 ` [PATCH 08/13] ARM: LPC32XX: Phytec 3250 platform support wellsk40 at gmail.com
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).