From: daniel@caiaq.de (Daniel Mack)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/3] ARM: MXC: mxcmmc: Teach the driver SDIO operations
Date: Tue, 30 Mar 2010 20:32:00 +0200 [thread overview]
Message-ID: <1269973921-29611-2-git-send-email-daniel@caiaq.de> (raw)
In-Reply-To: <1269973921-29611-1-git-send-email-daniel@caiaq.de>
Successfully tested on MX31 hardware using libertas SDIO peripherals.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Jiri Kosina <jkosina@suse.cz>
---
drivers/mmc/host/mxcmmc.c | 55 ++++++++++++++++++++++++++++++++++++--------
1 files changed, 45 insertions(+), 10 deletions(-)
diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c
index 21037ff..83a4545 100644
--- a/drivers/mmc/host/mxcmmc.c
+++ b/drivers/mmc/host/mxcmmc.c
@@ -119,6 +119,7 @@ struct mxcmci_host {
int detect_irq;
int dma;
int do_dma;
+ int use_sdio;
unsigned int power_mode;
struct imxmmc_platform_data *pdata;
@@ -138,6 +139,7 @@ struct mxcmci_host {
int clock;
struct work_struct datawork;
+ spinlock_t lock;
};
static void mxcmci_set_clk_rate(struct mxcmci_host *host, unsigned int clk_ios);
@@ -226,6 +228,8 @@ static int mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd,
unsigned int cmdat)
{
+ u32 int_cntr;
+
WARN_ON(host->cmd != NULL);
host->cmd = cmd;
@@ -249,13 +253,15 @@ static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd,
return -EINVAL;
}
+ int_cntr = INT_END_CMD_RES_EN;
+
if (mxcmci_use_dma(host))
- writel(INT_READ_OP_EN | INT_WRITE_OP_DONE_EN |
- INT_END_CMD_RES_EN,
- host->base + MMC_REG_INT_CNTR);
- else
- writel(INT_END_CMD_RES_EN, host->base + MMC_REG_INT_CNTR);
+ int_cntr |= INT_READ_OP_EN | INT_WRITE_OP_DONE_EN;
+
+ if (host->use_sdio)
+ int_cntr |= INT_SDIO_IRQ_EN;
+ writel(int_cntr, host->base + MMC_REG_INT_CNTR);
writew(cmd->opcode, host->base + MMC_REG_CMD);
writel(cmd->arg, host->base + MMC_REG_ARG);
writew(cmdat, host->base + MMC_REG_CMD_DAT_CONT);
@@ -266,7 +272,12 @@ static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd,
static void mxcmci_finish_request(struct mxcmci_host *host,
struct mmc_request *req)
{
- writel(0, host->base + MMC_REG_INT_CNTR);
+ u32 int_cntr = 0;
+
+ if (host->use_sdio)
+ int_cntr |= INT_SDIO_IRQ_EN;
+
+ writel(int_cntr, host->base + MMC_REG_INT_CNTR);
host->req = NULL;
host->cmd = NULL;
@@ -536,8 +547,12 @@ static irqreturn_t mxcmci_irq(int irq, void *devid)
dev_dbg(mmc_dev(host->mmc), "%s: 0x%08x\n", __func__, stat);
+ if ((stat & STATUS_SDIO_INT_ACTIVE) && host->use_sdio)
+ mmc_signal_sdio_irq(host->mmc);
+
if (stat & STATUS_END_CMD_RESP)
mxcmci_cmd_done(host, stat);
+
#ifdef HAS_DMA
if (mxcmci_use_dma(host) &&
(stat & (STATUS_DATA_TRANS_DONE | STATUS_WRITE_OP_DONE)))
@@ -674,11 +689,30 @@ static int mxcmci_get_ro(struct mmc_host *mmc)
return -ENOSYS;
}
+static void mxcmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
+{
+ struct mxcmci_host *host = mmc_priv(mmc);
+ unsigned long flags;
+ u32 int_cntr;
+
+ spin_lock_irqsave(&host->lock, flags);
+ host->use_sdio = enable;
+ int_cntr = readl(host->base + MMC_REG_INT_CNTR);
+
+ if (enable)
+ int_cntr |= INT_SDIO_IRQ_EN;
+ else
+ int_cntr &= ~INT_SDIO_IRQ_EN;
+
+ writel(int_cntr, host->base + MMC_REG_INT_CNTR);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
static const struct mmc_host_ops mxcmci_ops = {
- .request = mxcmci_request,
- .set_ios = mxcmci_set_ios,
- .get_ro = mxcmci_get_ro,
+ .request = mxcmci_request,
+ .set_ios = mxcmci_set_ios,
+ .get_ro = mxcmci_get_ro,
+ .enable_sdio_irq = mxcmci_enable_sdio_irq,
};
static int mxcmci_probe(struct platform_device *pdev)
@@ -706,7 +740,7 @@ static int mxcmci_probe(struct platform_device *pdev)
}
mmc->ops = &mxcmci_ops;
- mmc->caps = MMC_CAP_4_BIT_DATA;
+ mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
/* MMC core transfer sizes tunable parameters */
mmc->max_hw_segs = 64;
@@ -725,6 +759,7 @@ static int mxcmci_probe(struct platform_device *pdev)
host->mmc = mmc;
host->pdata = pdev->dev.platform_data;
+ spin_lock_init(&host->lock);
if (host->pdata && host->pdata->ocr_avail)
mmc->ocr_avail = host->pdata->ocr_avail;
--
1.7.0
next prev parent reply other threads:[~2010-03-30 18:32 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-03-30 18:31 [PATCH 1/3] ARM: MXC: mxcmmc: misc cleanups Daniel Mack
2010-03-30 18:32 ` Daniel Mack [this message]
2010-03-31 13:03 ` [PATCH 2/3] ARM: MXC: mxcmmc: Teach the driver SDIO operations Sascha Hauer
2010-03-31 13:29 ` Daniel Mack
2010-03-31 16:41 ` Michał Mirosław
2010-03-31 17:04 ` [PATCH] " Daniel Mack
2010-03-31 17:34 ` Michał Mirosław
2010-04-01 8:02 ` Daniel Mack
2010-03-30 18:32 ` [PATCH 3/3] ARM: MXC: mxcmmc: work around a bug in the SDHC busy line handling Daniel Mack
2010-03-31 12:38 ` [PATCH 1/3] ARM: MXC: mxcmmc: misc cleanups Sascha Hauer
2010-03-31 13:02 ` Daniel Mack
2010-03-31 13:35 ` [PATCH] " Daniel Mack
2010-03-31 13:17 ` [PATCH 1/3] " Julien Boibessot
-- strict thread matches above, loose matches on Subject: below --
2010-04-01 8:03 Daniel Mack
2010-04-01 8:03 ` [PATCH 2/3] ARM: MXC: mxcmmc: Teach the driver SDIO operations Daniel Mack
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1269973921-29611-2-git-send-email-daniel@caiaq.de \
--to=daniel@caiaq.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).