linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: weber@corscience.de (Thomas Weber)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCHv2 06/11] OMAP2: Devkit8000: Remove non existing vsim supply
Date: Wed,  2 Jun 2010 13:37:46 +0200	[thread overview]
Message-ID: <1275478671-24563-7-git-send-email-weber@corscience.de> (raw)
In-Reply-To: <1275478671-24563-1-git-send-email-weber@corscience.de>

The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.

vaux2 is not used on Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   22 ----------------------
 1 files changed, 0 insertions(+), 22 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 8cc8c3b..59877b1 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -168,15 +168,10 @@ static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
 {
 }
 
-
 static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
 	.supply			= "vmmc",
 };
 
-static struct regulator_consumer_supply devkit8000_vsim_supply = {
-	.supply			= "vmmc_aux",
-};
-
 /* ads7846 on SPI */
 static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
 	REGULATOR_SUPPLY("vcc", "spi2.0")
@@ -281,7 +276,6 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 
 	/* link regulators to MMC adapters */
 	devkit8000_vmmc1_supply.dev = mmc[0].dev;
-	devkit8000_vsim_supply.dev = mmc[0].dev;
 
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -334,21 +328,6 @@ static struct regulator_init_data devkit8000_vmmc1 = {
 	.consumer_supplies	= &devkit8000_vmmc1_supply,
 };
 
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data devkit8000_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= 1,
-	.consumer_supplies	= &devkit8000_vsim_supply,
-};
-
 /* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
 static struct regulator_init_data devkit8000_vdac = {
 	.constraints = {
@@ -414,7 +393,6 @@ static struct twl4030_platform_data devkit8000_twldata = {
 	.gpio		= &devkit8000_gpio_data,
 	.codec		= &devkit8000_codec_data,
 	.vmmc1		= &devkit8000_vmmc1,
-	.vsim		= &devkit8000_vsim,
 	.vdac		= &devkit8000_vdac,
 	.vpll1		= &devkit8000_vpll1,
 	.vio		= &devkit8000_vio,
-- 
1.7.1

  parent reply	other threads:[~2010-06-02 11:37 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-06-02 11:37 [PATCHv2 00/11] Multiple fixes for Devkit8000 Thomas Weber
2010-06-02 11:37 ` [PATCHv2 01/11] OMAP2: Devkit8000: Cleanup for power supplies Thomas Weber
2010-06-02 11:37 ` [PATCHv2 02/11] OMAP2: Devkit8000: change panel to generic panel Thomas Weber
2010-06-02 11:37 ` [PATCHv2 03/11] OMAP2: Devkit8000: Enable DVI-D output Thomas Weber
2010-06-02 11:37 ` [PATCHv2 04/11] OMAP2: Devkit8000: Setup LCD reset Thomas Weber
2010-07-05 12:57   ` Tony Lindgren
2010-06-02 11:37 ` [PATCHv2 05/11] OMAP2: Devkit8000: Remove unneeded VDVI supply Thomas Weber
2010-06-02 11:37 ` Thomas Weber [this message]
2010-06-02 11:37 ` [PATCHv2 07/11] OMAP2: Devkit8000: Remove en-/disable for tv panel Thomas Weber
2010-06-02 11:37 ` [PATCHv2 08/11] OMAP2: Devkit8000: Using the REGULATOR_SUPPLY macro Thomas Weber
2010-06-02 11:37 ` [PATCHv2 09/11] OMAP2: Devkit8000: Using gpio_is_valid macro Thomas Weber
2010-06-02 11:37 ` [PATCHv2 10/11] OMAP2: Devkit8000: Remove unused omap_board_config Thomas Weber
2010-06-02 11:37 ` [PATCHv2 11/11] OMAP2: Devkit8000: Fix regulator for power supply Thomas Weber

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1275478671-24563-7-git-send-email-weber@corscience.de \
    --to=weber@corscience.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).