[PATCH 1/8] MX25: put define for OTG base address in right include

[PATCH 1/8] MX25: put define for OTG base address in right include

[Eric Bénard]

the standard place for this define is include/mach/mx25.h

Signed-off-by: Eric B?nard <eric@eukrea.com>
---
 arch/arm/mach-mx25/devices.c          |    2 --
 arch/arm/plat-mxc/include/mach/mx25.h |    1 +
 2 files changed, 1 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-mx25/devices.c b/arch/arm/mach-mx25/devices.c
index 3a405fa..032a347 100644
--- a/arch/arm/mach-mx25/devices.c
+++ b/arch/arm/mach-mx25/devices.c
@@ -117,8 +117,6 @@ struct platform_device mxc_uart_device4 = {
 	.num_resources = ARRAY_SIZE(uart4),
 };
 
-#define MX25_OTG_BASE_ADDR 0x53FF4000
-
 static u64 otg_dmamask = DMA_BIT_MASK(32);
 
 static struct resource mxc_otg_resources[] = {
diff --git a/arch/arm/plat-mxc/include/mach/mx25.h b/arch/arm/plat-mxc/include/mach/mx25.h
index 4eb6e33..bc0ba27 100644
--- a/arch/arm/plat-mxc/include/mach/mx25.h
+++ b/arch/arm/plat-mxc/include/mach/mx25.h
@@ -34,6 +34,7 @@
 #define MX25_NFC_BASE_ADDR		0xbb000000
 #define MX25_DRYICE_BASE_ADDR		0x53ffc000
 #define MX25_LCDC_BASE_ADDR		0x53fbc000
+#define MX25_OTG_BASE_ADDR		0x53ff4000
 
 #define MX25_INT_DRYICE	25
 #define MX25_INT_FEC	57
-- 
1.6.3.3

[PATCH 2/8] plat-mxc/ehci.c: add i.MX25 support

[Eric Bénard]

i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.

Signed-off-by: Eric B?nard <eric@eukrea.com>
---
 arch/arm/plat-mxc/ehci.c |   46 +++++++++++++++++++++++++++++++++++++++++++++-
 1 files changed, 45 insertions(+), 1 deletions(-)

diff --git a/arch/arm/plat-mxc/ehci.c b/arch/arm/plat-mxc/ehci.c
index 2a86461..6184792 100644
--- a/arch/arm/plat-mxc/ehci.c
+++ b/arch/arm/plat-mxc/ehci.c
@@ -73,7 +73,51 @@
 int mxc_initialize_usb_hw(int port, unsigned int flags)
 {
 	unsigned int v;
-#ifdef CONFIG_ARCH_MX3
+#if defined(CONFIG_ARCH_MX25)
+	if (cpu_is_mx25()) {
+		v = readl(MX25_IO_ADDRESS(MX25_OTG_BASE_ADDR +
+				     USBCTRL_OTGBASE_OFFSET));
+
+		switch (port) {
+		case 0:	/* OTG port */
+			v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT);
+			v |= (flags & MXC_EHCI_INTERFACE_MASK)
+					<< MX35_OTG_SIC_SHIFT;
+			if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+				v |= MX35_OTG_PM_BIT;
+
+			break;
+		case 1: /* H1 port */
+			v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_TLL_BIT |
+				MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
+			v |= (flags & MXC_EHCI_INTERFACE_MASK)
+						<< MX35_H1_SIC_SHIFT;
+			if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+				v |= MX35_H1_PM_BIT;
+
+			if (!(flags & MXC_EHCI_TTL_ENABLED))
+				v |= MX35_H1_TLL_BIT;
+
+			if (flags & MXC_EHCI_INTERNAL_PHY)
+				v |= MX35_H1_USBTE_BIT;
+
+			if (flags & MXC_EHCI_IPPUE_DOWN)
+				v |= MX35_H1_IPPUE_DOWN_BIT;
+
+			if (flags & MXC_EHCI_IPPUE_UP)
+				v |= MX35_H1_IPPUE_UP_BIT;
+
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		writel(v, MX25_IO_ADDRESS(MX25_OTG_BASE_ADDR +
+				     USBCTRL_OTGBASE_OFFSET));
+		return 0;
+	}
+#endif /* CONFIG_ARCH_MX25 */
+#if defined(CONFIG_ARCH_MX3)
 	if (cpu_is_mx31()) {
 		v = readl(MX31_IO_ADDRESS(MX31_OTG_BASE_ADDR +
 				     USBCTRL_OTGBASE_OFFSET));
-- 
1.6.3.3

[PATCH 3/8] i.MX25: fix get_rate_otg to return the correct value

[Eric Bénard]

usb drivers need to get the right value for otg clock so
calculate and return it

Signed-off-by: Eric B?nard <eric@eukrea.com>
---
 arch/arm/mach-mx25/clock.c |    5 ++++-
 1 files changed, 4 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-mx25/clock.c b/arch/arm/mach-mx25/clock.c
index 1550149..d2835ff 100644
--- a/arch/arm/mach-mx25/clock.c
+++ b/arch/arm/mach-mx25/clock.c
@@ -131,7 +131,10 @@ static unsigned long get_rate_lcdc(struct clk *clk)
 
 static unsigned long get_rate_otg(struct clk *clk)
 {
-	return 48000000; /* FIXME */
+	unsigned long cctl = readl(CRM_BASE + CCM_CCTL);
+	unsigned long rate = get_rate_upll();
+
+	return (cctl & (1 << 23)) ? 0 : rate / ((0x3F & (cctl >> 16)) + 1);
 }
 
 static int clk_cgcr_enable(struct clk *clk)
-- 
1.6.3.3

[PATCH 4/8] i.MX25: fix EHCI support

[Eric Bénard]

i.MX25's EHCI is the same as i.MX35's one.

Signed-off-by: Eric B?nard <eric@eukrea.com>
---
 drivers/usb/host/ehci-mxc.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index 544ccfd..56f2750 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -182,7 +182,7 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 	}
 	clk_enable(priv->usbclk);
 
-	if (!cpu_is_mx35()) {
+	if (!cpu_is_mx35() && !cpu_is_mx25()) {
 		priv->ahbclk = clk_get(dev, "usb_ahb");
 		if (IS_ERR(priv->ahbclk)) {
 			ret = PTR_ERR(priv->ahbclk);
-- 
1.6.3.3

[PATCH 5/8] i.MX25: fix USB gadget support

[Eric Bénard]

i.MX25's udc port is the same as i.MX35's one

Signed-off-by: Eric B?nard <eric@eukrea.com>
---
 drivers/usb/gadget/fsl_mxc_udc.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/usb/gadget/fsl_mxc_udc.c b/drivers/usb/gadget/fsl_mxc_udc.c
index d0b8bde..eafa6d2 100644
--- a/drivers/usb/gadget/fsl_mxc_udc.c
+++ b/drivers/usb/gadget/fsl_mxc_udc.c
@@ -30,7 +30,7 @@ int fsl_udc_clk_init(struct platform_device *pdev)
 
 	pdata = pdev->dev.platform_data;
 
-	if (!cpu_is_mx35()) {
+	if (!cpu_is_mx35() && !cpu_is_mx25()) {
 		mxc_ahb_clk = clk_get(&pdev->dev, "usb_ahb");
 		if (IS_ERR(mxc_ahb_clk))
 			return PTR_ERR(mxc_ahb_clk);
-- 
1.6.3.3

[PATCH 6/8] i.MX25: add AUDMUX and SSI support

[Eric Bénard]

* add clocks for audmux and ssi 1 & 2
* add irq for ssi 1 & 2
* add devices platform for ssi1 & 2
* update audmux-v2 for i.MX25
* add base addresses for audmux & ssi 1 & 2
* add iomux configuration for GPIO for AUD5 port

Signed-off-by: Eric B?nard <eric@eukrea.com>
---
 arch/arm/mach-mx25/clock.c                  |   18 ++++++++++++
 arch/arm/mach-mx25/devices.c                |   38 +++++++++++++++++++++++++++
 arch/arm/mach-mx25/devices.h                |    2 +
 arch/arm/plat-mxc/Kconfig                   |    1 +
 arch/arm/plat-mxc/audmux-v2.c               |   15 ++++++++++-
 arch/arm/plat-mxc/include/mach/iomux-mx25.h |    4 +++
 arch/arm/plat-mxc/include/mach/mx25.h       |    7 ++++-
 7 files changed, 83 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-mx25/clock.c b/arch/arm/mach-mx25/clock.c
index d2835ff..bdf6e76 100644
--- a/arch/arm/mach-mx25/clock.c
+++ b/arch/arm/mach-mx25/clock.c
@@ -109,6 +109,16 @@ static unsigned long get_rate_uart(struct clk *clk)
 	return get_rate_per(15);
 }
 
+static unsigned long get_rate_ssi2(struct clk *clk)
+{
+	return get_rate_per(14);
+}
+
+static unsigned long get_rate_ssi1(struct clk *clk)
+{
+	return get_rate_per(13);
+}
+
 static unsigned long get_rate_i2c(struct clk *clk)
 {
 	return get_rate_per(6);
@@ -171,6 +181,8 @@ static void clk_cgcr_disable(struct clk *clk)
 
 DEFINE_CLOCK(gpt_clk,    0, CCM_CGCR0,  5, get_rate_gpt, NULL, NULL);
 DEFINE_CLOCK(uart_per_clk, 0, CCM_CGCR0, 15, get_rate_uart, NULL, NULL);
+DEFINE_CLOCK(ssi1_per_clk, 0, CCM_CGCR0, 13, get_rate_ipg, NULL, NULL);
+DEFINE_CLOCK(ssi2_per_clk, 0, CCM_CGCR0, 14, get_rate_ipg, NULL, NULL);
 DEFINE_CLOCK(cspi1_clk,  0, CCM_CGCR1,  5, get_rate_ipg, NULL, NULL);
 DEFINE_CLOCK(cspi2_clk,  0, CCM_CGCR1,  6, get_rate_ipg, NULL, NULL);
 DEFINE_CLOCK(cspi3_clk,  0, CCM_CGCR1,  7, get_rate_ipg, NULL, NULL);
@@ -194,6 +206,9 @@ DEFINE_CLOCK(i2c_clk,	 0, CCM_CGCR0,  6, get_rate_i2c, NULL, NULL);
 DEFINE_CLOCK(fec_clk,	 0, CCM_CGCR1, 15, get_rate_ipg, NULL, &fec_ahb_clk);
 DEFINE_CLOCK(dryice_clk, 0, CCM_CGCR1,  8, get_rate_ipg, NULL, NULL);
 DEFINE_CLOCK(lcdc_clk,	 0, CCM_CGCR1, 29, get_rate_lcdc, NULL, &lcdc_per_clk);
+DEFINE_CLOCK(ssi1_clk,  0, CCM_CGCR2, 11, get_rate_ssi1, NULL, &ssi1_per_clk);
+DEFINE_CLOCK(ssi2_clk,  1, CCM_CGCR2, 12, get_rate_ssi2, NULL, &ssi2_per_clk);
+DEFINE_CLOCK(audmux_clk, 0, CCM_CGCR1, 0, NULL, NULL, NULL);
 
 #define _REGISTER_CLOCK(d, n, c)	\
 	{				\
@@ -228,6 +243,9 @@ static struct clk_lookup lookups[] = {
 	_REGISTER_CLOCK("fec.0", NULL, fec_clk)
 	_REGISTER_CLOCK("imxdi_rtc.0", NULL, dryice_clk)
 	_REGISTER_CLOCK("imx-fb.0", NULL, lcdc_clk)
+	_REGISTER_CLOCK("imx-ssi.0", NULL, ssi1_clk)
+	_REGISTER_CLOCK("imx-ssi.1", NULL, ssi2_clk)
+	_REGISTER_CLOCK(NULL, "audmux", audmux_clk)
 };
 
 int __init mx25_clocks_init(void)
diff --git a/arch/arm/mach-mx25/devices.c b/arch/arm/mach-mx25/devices.c
index 032a347..1382fcf 100644
--- a/arch/arm/mach-mx25/devices.c
+++ b/arch/arm/mach-mx25/devices.c
@@ -513,3 +513,41 @@ struct platform_device mxc_wdt = {
 	.num_resources = ARRAY_SIZE(mxc_wdt_resources),
 	.resource = mxc_wdt_resources,
 };
+
+static struct resource imx_ssi_resources0[] = {
+	{
+		.start	= MX25_SSI1_BASE_ADDR,
+		.end	= MX25_SSI1_BASE_ADDR + 0x3fff,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= MX25_INT_SSI1,
+		.end	= MX25_INT_SSI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct resource imx_ssi_resources1[] = {
+	{
+		.start	= MX25_SSI2_BASE_ADDR,
+		.end	= MX25_SSI2_BASE_ADDR + 0x3fff,
+		.flags	= IORESOURCE_MEM
+	}, {
+		.start	= MX25_INT_SSI2,
+		.end	= MX25_INT_SSI2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device imx_ssi_device0 = {
+	.name = "imx-ssi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(imx_ssi_resources0),
+	.resource = imx_ssi_resources0,
+};
+
+struct platform_device imx_ssi_device1 = {
+	.name = "imx-ssi",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(imx_ssi_resources1),
+	.resource = imx_ssi_resources1,
+};
diff --git a/arch/arm/mach-mx25/devices.h b/arch/arm/mach-mx25/devices.h
index cee12c0..f886e82 100644
--- a/arch/arm/mach-mx25/devices.h
+++ b/arch/arm/mach-mx25/devices.h
@@ -22,3 +22,5 @@ extern struct platform_device mxc_nand_device;
 extern struct platform_device mx25_rtc_device;
 extern struct platform_device mx25_fb_device;
 extern struct platform_device mxc_wdt;
+extern struct platform_device imx_ssi_device0;
+extern struct platform_device imx_ssi_device1;
diff --git a/arch/arm/plat-mxc/Kconfig b/arch/arm/plat-mxc/Kconfig
index 7f7ad6f..902ba9e 100644
--- a/arch/arm/plat-mxc/Kconfig
+++ b/arch/arm/plat-mxc/Kconfig
@@ -25,6 +25,7 @@ config ARCH_MX25
 	select CPU_ARM926T
 	select ARCH_MXC_IOMUX_V3
 	select HAVE_FB_IMX
+	select ARCH_MXC_AUDMUX_V2
 	help
 	  This enables support for systems based on the Freescale i.MX25 family
 
diff --git a/arch/arm/plat-mxc/audmux-v2.c b/arch/arm/plat-mxc/audmux-v2.c
index 0c2cc5c..ab94d78 100644
--- a/arch/arm/plat-mxc/audmux-v2.c
+++ b/arch/arm/plat-mxc/audmux-v2.c
@@ -191,6 +191,7 @@ static int mxc_audmux_v2_init(void)
 {
 	int ret;
 
+#if defined(CONFIG_ARCH_MX3)
 	if (cpu_is_mx31())
 		audmux_base = MX31_IO_ADDRESS(MX31_AUDMUX_BASE_ADDR);
 
@@ -204,7 +205,19 @@ static int mxc_audmux_v2_init(void)
 		}
 		audmux_base = MX35_IO_ADDRESS(MX35_AUDMUX_BASE_ADDR);
 	}
-
+#endif
+#if defined(CONFIG_ARCH_MX25)
+	if (cpu_is_mx25()) {
+		audmux_clk = clk_get(NULL, "audmux");
+		if (IS_ERR(audmux_clk)) {
+			ret = PTR_ERR(audmux_clk);
+			printk(KERN_ERR "%s: cannot get clock: %d\n", __func__,
+					ret);
+			return ret;
+		}
+		audmux_base = MX25_IO_ADDRESS(MX25_AUDMUX_BASE_ADDR);
+	}
+#endif
 	audmux_debugfs_init();
 
 	return 0;
diff --git a/arch/arm/plat-mxc/include/mach/iomux-mx25.h b/arch/arm/plat-mxc/include/mach/iomux-mx25.h
index f39220d..5bea603 100644
--- a/arch/arm/plat-mxc/include/mach/iomux-mx25.h
+++ b/arch/arm/plat-mxc/include/mach/iomux-mx25.h
@@ -386,15 +386,19 @@
 #define MX25_PAD_KPP_ROW3__GPIO_3_0	IOMUX_PAD(0x3ac, 0x1b4, 0x15, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_KPP_COL0__KPP_COL0	IOMUX_PAD(0x3b0, 0x1b8, 0x10, 0, 0, PAD_CTL_PKE | PAD_CTL_ODE)
+#define MX25_PAD_KPP_COL0__AUD5_TXD	IOMUX_PAD(0x3b0, 0x1b8, 0x12, 0, 0, PAD_CTL_PKE | PAD_CTL_PUS_100K_UP)
 #define MX25_PAD_KPP_COL0__GPIO_3_1	IOMUX_PAD(0x3b0, 0x1b8, 0x15, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_KPP_COL1__KPP_COL1	IOMUX_PAD(0x3b4, 0x1bc, 0x10, 0, 0, PAD_CTL_PKE | PAD_CTL_ODE)
+#define MX25_PAD_KPP_COL1__AUD5_RXD	IOMUX_PAD(0x3b4, 0x1bc, 0x12, 0, 0, PAD_CTL_PKE | PAD_CTL_PUS_100K_UP)
 #define MX25_PAD_KPP_COL1__GPIO_3_2	IOMUX_PAD(0x3b4, 0x1bc, 0x15, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_KPP_COL2__KPP_COL2	IOMUX_PAD(0x3b8, 0x1c0, 0x10, 0, 0, PAD_CTL_PKE | PAD_CTL_ODE)
+#define MX25_PAD_KPP_COL2__AUD5_TXC	IOMUX_PAD(0x3b8, 0x1c0, 0x12, 0, 0, PAD_CTL_PKE | PAD_CTL_PUS_100K_UP)
 #define MX25_PAD_KPP_COL2__GPIO_3_3	IOMUX_PAD(0x3b8, 0x1c0, 0x15, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_KPP_COL3__KPP_COL3	IOMUX_PAD(0x3bc, 0x1c4, 0x10, 0, 0, PAD_CTL_PKE | PAD_CTL_ODE)
+#define MX25_PAD_KPP_COL3__AUD5_TXFS	IOMUX_PAD(0x3bc, 0x1c4, 0x12, 0, 0, PAD_CTL_PKE | PAD_CTL_PUS_100K_UP)
 #define MX25_PAD_KPP_COL3__GPIO_3_4	IOMUX_PAD(0x3bc, 0x1c4, 0x15, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_FEC_MDC__FEC_MDC	IOMUX_PAD(0x3c0, 0x1c8, 0x10, 0, 0, NO_PAD_CTRL)
diff --git a/arch/arm/plat-mxc/include/mach/mx25.h b/arch/arm/plat-mxc/include/mach/mx25.h
index bc0ba27..2a5cd18 100644
--- a/arch/arm/plat-mxc/include/mach/mx25.h
+++ b/arch/arm/plat-mxc/include/mach/mx25.h
@@ -29,17 +29,22 @@
 
 #define MX25_UART1_BASE_ADDR		0x43f90000
 #define MX25_UART2_BASE_ADDR		0x43f94000
+#define MX25_AUDMUX_BASE_ADDR		0x43fb0000
 
 #define MX25_FEC_BASE_ADDR		0x50038000
+#define MX25_SSI2_BASE_ADDR		0x50014000
+#define MX25_SSI1_BASE_ADDR		0x50034000
 #define MX25_NFC_BASE_ADDR		0xbb000000
 #define MX25_DRYICE_BASE_ADDR		0x53ffc000
 #define MX25_LCDC_BASE_ADDR		0x53fbc000
 #define MX25_OTG_BASE_ADDR		0x53ff4000
 
+#define MX25_INT_SSI2	11
+#define MX25_INT_SSI1	12
 #define MX25_INT_DRYICE	25
-#define MX25_INT_FEC	57
 #define MX25_INT_NANDFC	33
 #define MX25_INT_LCDC	39
+#define MX25_INT_FEC	57
 
 #if defined(IMX_NEEDS_DEPRECATED_SYMBOLS)
 #define UART1_BASE_ADDR			MX25_UART1_BASE_ADDR
-- 
1.6.3.3

[PATCH 7/8] i.MX25: add cpuimx25 module and its baseboard

[Eric Bénard]

* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host
and USB OTG
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...

Signed-off-by: Eric B?nard <eric@eukrea.com>
---
 arch/arm/mach-mx25/Kconfig                         |   18 ++
 arch/arm/mach-mx25/Makefile                        |    2 +
 arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c      |  260 ++++++++++++++++++++
 arch/arm/mach-mx25/mach-cpuimx25.c                 |  172 +++++++++++++
 .../plat-mxc/include/mach/board-eukrea_cpuimx25.h  |   40 +++
 5 files changed, 492 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c
 create mode 100644 arch/arm/mach-mx25/mach-cpuimx25.c
 create mode 100644 arch/arm/plat-mxc/include/mach/board-eukrea_cpuimx25.h

diff --git a/arch/arm/mach-mx25/Kconfig b/arch/arm/mach-mx25/Kconfig
index 54d2173..3a6668e 100644
--- a/arch/arm/mach-mx25/Kconfig
+++ b/arch/arm/mach-mx25/Kconfig
@@ -5,4 +5,22 @@ comment "MX25 platforms:"
 config MACH_MX25_3DS
 	bool "Support MX25PDK (3DS) Platform"
 
+config MACH_EUKREA_CPUIMX25
+	bool "Support Eukrea CPUIMX25 Platform"
+	select MXC_ULPI if USB_ULPI
+
+choice
+	prompt "Baseboard"
+	depends on MACH_EUKREA_CPUIMX25
+	default MACH_EUKREA_MBIMXSD_BASEBOARD
+
+config MACH_EUKREA_MBIMXSD_BASEBOARD
+	prompt "Eukrea MBIMXSD development board"
+	bool
+	help
+	  This adds board specific devices that can be found on Eukrea's
+	  MBIMXSD evaluation board.
+
+endchoice
+
 endif
diff --git a/arch/arm/mach-mx25/Makefile b/arch/arm/mach-mx25/Makefile
index 10cebc5..83ab5d8 100644
--- a/arch/arm/mach-mx25/Makefile
+++ b/arch/arm/mach-mx25/Makefile
@@ -1,3 +1,5 @@
 obj-y				:= mm.o devices.o
 obj-$(CONFIG_ARCH_MX25)		+= clock.o
 obj-$(CONFIG_MACH_MX25_3DS)	+= mach-mx25pdk.o
+obj-$(CONFIG_MACH_EUKREA_CPUIMX25)		+= mach-cpuimx25.o
+obj-$(CONFIG_MACH_EUKREA_MBIMXSD_BASEBOARD)	+= eukrea_mbimxsd-baseboard.o
diff --git a/arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c b/arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c
new file mode 100644
index 0000000..e0f0dfd
--- /dev/null
+++ b/arch/arm/mach-mx25/eukrea_mbimxsd-baseboard.c
@@ -0,0 +1,260 @@
+/*
+ * Copyright (C) 2010 Eric Benard - eric at eukrea.com
+ *
+ * Based on pcm970-baseboard.c which is :
+ * Copyright (C) 2008 Juergen Beisert (kernel at pengutronix.de)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/platform_device.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <video/platform_lcd.h>
+
+#include <mach/board-eukrea_cpuimx25.h>
+#include <mach/hardware.h>
+#include <mach/iomux-mx25.h>
+#include <mach/common.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/mx25.h>
+#include <mach/imx-uart.h>
+#include <mach/imxfb.h>
+#include <mach/ssi.h>
+#include <mach/audmux.h>
+
+#include "devices.h"
+
+static struct pad_desc eukrea_mbimxsd_pads[] = {
+	/* LCD */
+	MX25_PAD_LD0__LD0,
+	MX25_PAD_LD1__LD1,
+	MX25_PAD_LD2__LD2,
+	MX25_PAD_LD3__LD3,
+	MX25_PAD_LD4__LD4,
+	MX25_PAD_LD5__LD5,
+	MX25_PAD_LD6__LD6,
+	MX25_PAD_LD7__LD7,
+	MX25_PAD_LD8__LD8,
+	MX25_PAD_LD9__LD9,
+	MX25_PAD_LD10__LD10,
+	MX25_PAD_LD11__LD11,
+	MX25_PAD_LD12__LD12,
+	MX25_PAD_LD13__LD13,
+	MX25_PAD_LD14__LD14,
+	MX25_PAD_LD15__LD15,
+	MX25_PAD_GPIO_E__LD16,
+	MX25_PAD_GPIO_F__LD17,
+	MX25_PAD_HSYNC__HSYNC,
+	MX25_PAD_VSYNC__VSYNC,
+	MX25_PAD_LSCLK__LSCLK,
+	MX25_PAD_OE_ACD__OE_ACD,
+	MX25_PAD_CONTRAST__CONTRAST,
+	/* LCD_PWR */
+	MX25_PAD_PWM__GPIO_1_26,
+	/* LED */
+	MX25_PAD_POWER_FAIL__GPIO_3_19,
+	/* SWITCH */
+	MX25_PAD_VSTBY_ACK__GPIO_3_18,
+	/* UART2 */
+	MX25_PAD_UART2_RTS__UART2_RTS,
+	MX25_PAD_UART2_CTS__UART2_CTS,
+	MX25_PAD_UART2_TXD__UART2_TXD,
+	MX25_PAD_UART2_RXD__UART2_RXD,
+	/* SD1 */
+	MX25_PAD_SD1_CMD__SD1_CMD,
+	MX25_PAD_SD1_CLK__SD1_CLK,
+	MX25_PAD_SD1_DATA0__SD1_DATA0,
+	MX25_PAD_SD1_DATA1__SD1_DATA1,
+	MX25_PAD_SD1_DATA2__SD1_DATA2,
+	MX25_PAD_SD1_DATA3__SD1_DATA3,
+	/* SD1 CD */
+	MX25_PAD_DE_B__GPIO_2_20,
+	/* I2S */
+	MX25_PAD_KPP_COL3__AUD5_TXFS,
+	MX25_PAD_KPP_COL2__AUD5_TXC,
+	MX25_PAD_KPP_COL1__AUD5_RXD,
+	MX25_PAD_KPP_COL0__AUD5_TXD,
+};
+
+#define GPIO_LED1	83
+#define GPIO_SWITCH1	82
+#define GPIO_SD1CD	52
+#define GPIO_LCDPWR	26
+
+static struct imx_fb_videomode eukrea_mximxsd_modes[] = {
+	{
+		.mode	= {
+			.name		= "CMO-QVGA",
+			.refresh	= 60,
+			.xres		= 320,
+			.yres		= 240,
+			.pixclock	= KHZ2PICOS(6500),
+			.left_margin	= 30,
+			.right_margin	= 38,
+			.upper_margin	= 20,
+			.lower_margin	= 3,
+			.hsync_len	= 15,
+			.vsync_len	= 4,
+		},
+		.bpp	= 16,
+		.pcr	= 0xCAD08B80,
+	},
+};
+
+static struct imx_fb_platform_data eukrea_mximxsd_fb_pdata = {
+	.mode		= eukrea_mximxsd_modes,
+	.num_modes	= ARRAY_SIZE(eukrea_mximxsd_modes),
+	.pwmr		= 0x00A903FF,
+	.lscr1		= 0x00120300,
+	.dmacr		= 0x00040060,
+};
+
+static void eukrea_mbimxsd_lcd_power_set(struct plat_lcd_data *pd,
+				   unsigned int power)
+{
+	if (power)
+		gpio_direction_output(GPIO_LCDPWR, 1);
+	else
+		gpio_direction_output(GPIO_LCDPWR, 0);
+}
+
+static struct plat_lcd_data eukrea_mbimxsd_lcd_power_data = {
+	.set_power		= eukrea_mbimxsd_lcd_power_set,
+};
+
+static struct platform_device eukrea_mbimxsd_lcd_powerdev = {
+	.name			= "platform-lcd",
+	.dev.platform_data	= &eukrea_mbimxsd_lcd_power_data,
+};
+
+static struct gpio_led eukrea_mbimxsd_leds[] = {
+	{
+		.name			= "led1",
+		.default_trigger	= "heartbeat",
+		.active_low		= 1,
+		.gpio			= GPIO_LED1,
+	},
+};
+
+static struct gpio_led_platform_data eukrea_mbimxsd_led_info = {
+	.leds		= eukrea_mbimxsd_leds,
+	.num_leds	= ARRAY_SIZE(eukrea_mbimxsd_leds),
+};
+
+static struct platform_device eukrea_mbimxsd_leds_gpio = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &eukrea_mbimxsd_led_info,
+	},
+};
+
+static struct gpio_keys_button eukrea_mbimxsd_gpio_buttons[] = {
+	{
+		.gpio		= GPIO_SWITCH1,
+		.code		= BTN_0,
+		.desc		= "BP1",
+		.active_low	= 1,
+		.wakeup		= 1,
+	},
+};
+
+static struct gpio_keys_platform_data eukrea_mbimxsd_button_data = {
+	.buttons	= eukrea_mbimxsd_gpio_buttons,
+	.nbuttons	= ARRAY_SIZE(eukrea_mbimxsd_gpio_buttons),
+};
+
+static struct platform_device eukrea_mbimxsd_button_device = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.num_resources	= 0,
+	.dev		= {
+		.platform_data	= &eukrea_mbimxsd_button_data,
+	}
+};
+
+static struct platform_device *platform_devices[] __initdata = {
+	&eukrea_mbimxsd_leds_gpio,
+	&eukrea_mbimxsd_button_device,
+	&eukrea_mbimxsd_lcd_powerdev,
+};
+
+static struct imxuart_platform_data uart_pdata = {
+	.flags = IMXUART_HAVE_RTSCTS,
+};
+
+static struct i2c_board_info eukrea_mbimxsd_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("tlv320aic23", 0x1a),
+	},
+};
+
+struct imx_ssi_platform_data eukrea_mbimxsd_ssi_pdata = {
+	.flags = IMX_SSI_SYN | IMX_SSI_NET | IMX_SSI_USE_I2S_SLAVE,
+};
+
+/*
+ * system init for baseboard usage. Will be called by cpuimx25 init.
+ *
+ * Add platform devices present on this baseboard and init
+ * them from CPU side as far as required to use them later on
+ */
+void __init eukrea_mbimxsd_baseboard_init(void)
+{
+	if (mxc_iomux_v3_setup_multiple_pads(eukrea_mbimxsd_pads,
+			ARRAY_SIZE(eukrea_mbimxsd_pads)))
+		printk(KERN_ERR "error setting mbimxsd pads !\n");
+
+#if defined(CONFIG_SND_SOC_EUKREA_TLV320)
+	/* SSI unit master I2S codec connected to SSI_AUD5*/
+	mxc_audmux_v2_configure_port(0,
+			MXC_AUDMUX_V2_PTCR_SYN |
+			MXC_AUDMUX_V2_PTCR_TFSDIR |
+			MXC_AUDMUX_V2_PTCR_TFSEL(4) |
+			MXC_AUDMUX_V2_PTCR_TCLKDIR |
+			MXC_AUDMUX_V2_PTCR_TCSEL(4),
+			MXC_AUDMUX_V2_PDCR_RXDSEL(4)
+	);
+	mxc_audmux_v2_configure_port(4,
+			MXC_AUDMUX_V2_PTCR_SYN,
+			MXC_AUDMUX_V2_PDCR_RXDSEL(0)
+	);
+#endif
+
+	mxc_register_device(&mxc_uart_device1, &uart_pdata);
+	mxc_register_device(&mx25_fb_device, &eukrea_mximxsd_fb_pdata);
+	mxc_register_device(&imx_ssi_device0, &eukrea_mbimxsd_ssi_pdata);
+
+	gpio_request(GPIO_LED1, "LED1");
+	gpio_direction_output(GPIO_LED1, 1);
+	gpio_free(GPIO_LED1);
+
+	gpio_request(GPIO_SWITCH1, "SWITCH1");
+	gpio_direction_input(GPIO_SWITCH1);
+	gpio_free(GPIO_SWITCH1);
+
+	gpio_request(GPIO_LCDPWR, "LCDPWR");
+	gpio_direction_output(GPIO_LCDPWR, 1);
+	gpio_free(GPIO_SWITCH1);
+
+	i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices,
+				ARRAY_SIZE(eukrea_mbimxsd_i2c_devices));
+
+	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+}
diff --git a/arch/arm/mach-mx25/mach-cpuimx25.c b/arch/arm/mach-mx25/mach-cpuimx25.c
new file mode 100644
index 0000000..4796484
--- /dev/null
+++ b/arch/arm/mach-mx25/mach-cpuimx25.c
@@ -0,0 +1,172 @@
+/*
+ * Copyright 2009 Sascha Hauer, <kernel@pengutronix.de>
+ * Copyright 2010 Eric B?nard - Eukr?a Electromatique, <eric@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor,
+ * Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+#include <linux/fec.h>
+#include <linux/platform_device.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/ulpi.h>
+#include <linux/fsl_devices.h>
+
+#include <mach/board-eukrea_cpuimx25.h>
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <asm/memory.h>
+#include <asm/mach/map.h>
+#include <mach/common.h>
+#include <mach/imx-uart.h>
+#include <mach/i2c.h>
+#include <mach/mx25.h>
+#include <mach/mxc_nand.h>
+#include <mach/imxfb.h>
+#include <mach/mxc_ehci.h>
+#include <mach/ulpi.h>
+
+#include "devices.h"
+#include <mach/iomux-mx25.h>
+
+static struct imxuart_platform_data uart_pdata = {
+	.flags = IMXUART_HAVE_RTSCTS,
+};
+
+static struct pad_desc eukrea_cpuimx25_pads[] = {
+	/* FEC - RMII */
+	MX25_PAD_FEC_MDC__FEC_MDC,
+	MX25_PAD_FEC_MDIO__FEC_MDIO,
+	MX25_PAD_FEC_TDATA0__FEC_TDATA0,
+	MX25_PAD_FEC_TDATA1__FEC_TDATA1,
+	MX25_PAD_FEC_TX_EN__FEC_TX_EN,
+	MX25_PAD_FEC_RDATA0__FEC_RDATA0,
+	MX25_PAD_FEC_RDATA1__FEC_RDATA1,
+	MX25_PAD_FEC_RX_DV__FEC_RX_DV,
+	MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
+	/* I2C1 */
+	MX25_PAD_I2C1_CLK__I2C1_CLK,
+	MX25_PAD_I2C1_DAT__I2C1_DAT,
+};
+
+static struct fec_platform_data mx25_fec_pdata = {
+	.phy	= PHY_INTERFACE_MODE_RMII,
+};
+
+static struct mxc_nand_platform_data eukrea_cpuimx25_nand_board_info = {
+	.width		= 1,
+	.hw_ecc		= 1,
+	.flash_bbt	= 1,
+};
+
+static struct imxi2c_platform_data eukrea_cpuimx25_i2c_1_data = {
+	.bitrate = 100000,
+};
+
+static struct i2c_board_info eukrea_cpuimx25_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("pcf8563", 0x51),
+	},
+};
+
+static struct mxc_usbh_platform_data otg_pdata = {
+	.portsc	= MXC_EHCI_MODE_UTMI,
+	.flags	= MXC_EHCI_INTERFACE_DIFF_UNI,
+};
+
+static struct mxc_usbh_platform_data usbh2_pdata = {
+	.portsc	= MXC_EHCI_MODE_SERIAL,
+	.flags	= MXC_EHCI_INTERFACE_SINGLE_UNI | MXC_EHCI_INTERNAL_PHY |
+		  MXC_EHCI_IPPUE_DOWN,
+};
+
+static struct fsl_usb2_platform_data otg_device_pdata = {
+	.operating_mode = FSL_USB2_DR_DEVICE,
+	.phy_mode       = FSL_USB2_PHY_UTMI,
+};
+
+static int otg_mode_host;
+
+static int __init eukrea_cpuimx25_otg_mode(char *options)
+{
+	if (!strcmp(options, "host"))
+		otg_mode_host = 1;
+	else if (!strcmp(options, "device"))
+		otg_mode_host = 0;
+	else
+		pr_info("otg_mode neither \"host\" nor \"device\". "
+			"Defaulting to device\n");
+	return 0;
+}
+__setup("otg_mode=", eukrea_cpuimx25_otg_mode);
+
+static void __init eukrea_cpuimx25_init(void)
+{
+	if (mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx25_pads,
+			ARRAY_SIZE(eukrea_cpuimx25_pads)))
+		printk(KERN_ERR "error setting cpuimx25 pads !\n");
+
+	mxc_register_device(&mxc_uart_device0, &uart_pdata);
+	mxc_register_device(&mxc_nand_device, &eukrea_cpuimx25_nand_board_info);
+	mxc_register_device(&mx25_rtc_device, NULL);
+	mxc_register_device(&mx25_fec_device, &mx25_fec_pdata);
+
+	i2c_register_board_info(0, eukrea_cpuimx25_i2c_devices,
+				ARRAY_SIZE(eukrea_cpuimx25_i2c_devices));
+	mxc_register_device(&mxc_i2c_device0, &eukrea_cpuimx25_i2c_1_data);
+
+#if defined(CONFIG_USB_ULPI)
+	if (otg_mode_host) {
+		otg_pdata.otg = otg_ulpi_create(&mxc_ulpi_access_ops,
+				USB_OTG_DRV_VBUS | USB_OTG_DRV_VBUS_EXT);
+
+		mxc_register_device(&mxc_otg, &otg_pdata);
+	}
+	mxc_register_device(&mxc_usbh2, &usbh2_pdata);
+#endif
+	if (!otg_mode_host)
+		mxc_register_device(&otg_udc_device, &otg_device_pdata);
+
+#ifdef CONFIG_MACH_EUKREA_MBIMXSD_BASEBOARD
+	eukrea_mbimxsd_baseboard_init();
+#endif
+}
+
+static void __init eukrea_cpuimx25_timer_init(void)
+{
+	mx25_clocks_init();
+}
+
+static struct sys_timer eukrea_cpuimx25_timer = {
+	.init   = eukrea_cpuimx25_timer_init,
+};
+
+MACHINE_START(EUKREA_CPUIMX25, "Eukrea CPUIMX25")
+	/* Maintainer: Eukrea Electromatique */
+	.phys_io	= MX25_AIPS1_BASE_ADDR,
+	.io_pg_offst	= ((MX25_AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc,
+	.boot_params    = MX25_PHYS_OFFSET + 0x100,
+	.map_io         = mx25_map_io,
+	.init_irq       = mx25_init_irq,
+	.init_machine   = eukrea_cpuimx25_init,
+	.timer          = &eukrea_cpuimx25_timer,
+MACHINE_END
diff --git a/arch/arm/plat-mxc/include/mach/board-eukrea_cpuimx25.h b/arch/arm/plat-mxc/include/mach/board-eukrea_cpuimx25.h
new file mode 100644
index 0000000..5c9901e
--- /dev/null
+++ b/arch/arm/plat-mxc/include/mach/board-eukrea_cpuimx25.h
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2010 Eric Benard - eric at eukrea.com
+ *
+ * Based on board-pcm038.h which is :
+ * Copyright (C) 2008 Juergen Beisert (kernel at pengutronix.de)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef __ASM_ARCH_MXC_BOARD_EUKREA_CPUIMX25_H__
+#define __ASM_ARCH_MXC_BOARD_EUKREA_CPUIMX25_H__
+
+#ifndef __ASSEMBLY__
+/*
+ * This CPU module needs a baseboard to work. After basic initializing
+ * its own devices, it calls baseboard's init function.
+ * TODO: Add your own baseboard init function and call it from
+ * inside eukrea_cpuimx25_init().
+ *
+ * This example here is for the development board. Refer
+ * eukrea_mbimx25-baseboard.c
+ */
+
+extern void eukrea_mbimxsd_baseboard_init(void);
+
+#endif
+
+#endif /* __ASM_ARCH_MXC_BOARD_EUKREA_CPUIMX25_H__ */
-- 
1.6.3.3

[PATCH 8/8] eukrea-tlv320: add support for our i.MX25 board

[Eric Bénard]

* tdm slot has to be configured to get sound working on i.MX25

Signed-off-by: Eric B?nard <eric@eukrea.com>
---
 sound/soc/imx/Kconfig         |    2 +-
 sound/soc/imx/eukrea-tlv320.c |    3 ++-
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/sound/soc/imx/Kconfig b/sound/soc/imx/Kconfig
index fd292f1..fd616ae 100644
--- a/sound/soc/imx/Kconfig
+++ b/sound/soc/imx/Kconfig
@@ -31,7 +31,7 @@ config SND_SOC_PHYCORE_AC97
 
 config SND_SOC_EUKREA_TLV320
 	bool "Eukrea TLV320"
-	depends on MACH_EUKREA_MBIMX27_BASEBOARD
+	depends on MACH_EUKREA_MBIMX27_BASEBOARD || MACH_EUKREA_MBIMXSD_BASEBOARD
 	select SND_MXC_SOC_SSI
 	select SND_SOC_TLV320AIC23
 	help
diff --git a/sound/soc/imx/eukrea-tlv320.c b/sound/soc/imx/eukrea-tlv320.c
index 968380a..45f5e4b 100644
--- a/sound/soc/imx/eukrea-tlv320.c
+++ b/sound/soc/imx/eukrea-tlv320.c
@@ -60,6 +60,7 @@ static int eukrea_tlv320_hw_params(struct snd_pcm_substream *substream,
 		pr_err("%s: failed setting codec sysclk\n", __func__);
 		return ret;
 	}
+	snd_soc_dai_set_tdm_slot(cpu_dai, 0xffffffc, 0xffffffc, 2, 0);
 
 	ret = snd_soc_dai_set_sysclk(cpu_dai, IMX_SSP_SYS_CLK, 0,
 				SND_SOC_CLOCK_IN);
@@ -100,7 +101,7 @@ static int __init eukrea_tlv320_init(void)
 {
 	int ret;
 
-	if (!machine_is_eukrea_cpuimx27())
+	if (!machine_is_eukrea_cpuimx27() && !machine_is_eukrea_cpuimx25sd())
 		/* return happy. We might run on a totally different machine */
 		return 0;
 
-- 
1.6.3.3

[PATCH 1/8] MX25: put define for OTG base address in right include

[Sascha Hauer]

Hi Eric,

applied all but the last one which needs another patch.

Sascha

On Tue, Jun 08, 2010 at 11:02:55AM +0200, Eric B?nard wrote:
> the standard place for this define is include/mach/mx25.h
> 
> Signed-off-by: Eric B?nard <eric@eukrea.com>
> ---
>  arch/arm/mach-mx25/devices.c          |    2 --
>  arch/arm/plat-mxc/include/mach/mx25.h |    1 +
>  2 files changed, 1 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/mach-mx25/devices.c b/arch/arm/mach-mx25/devices.c
> index 3a405fa..032a347 100644
> --- a/arch/arm/mach-mx25/devices.c
> +++ b/arch/arm/mach-mx25/devices.c
> @@ -117,8 +117,6 @@ struct platform_device mxc_uart_device4 = {
>  	.num_resources = ARRAY_SIZE(uart4),
>  };
>  
> -#define MX25_OTG_BASE_ADDR 0x53FF4000
> -
>  static u64 otg_dmamask = DMA_BIT_MASK(32);
>  
>  static struct resource mxc_otg_resources[] = {
> diff --git a/arch/arm/plat-mxc/include/mach/mx25.h b/arch/arm/plat-mxc/include/mach/mx25.h
> index 4eb6e33..bc0ba27 100644
> --- a/arch/arm/plat-mxc/include/mach/mx25.h
> +++ b/arch/arm/plat-mxc/include/mach/mx25.h
> @@ -34,6 +34,7 @@
>  #define MX25_NFC_BASE_ADDR		0xbb000000
>  #define MX25_DRYICE_BASE_ADDR		0x53ffc000
>  #define MX25_LCDC_BASE_ADDR		0x53fbc000
> +#define MX25_OTG_BASE_ADDR		0x53ff4000
>  
>  #define MX25_INT_DRYICE	25
>  #define MX25_INT_FEC	57
> -- 
> 1.6.3.3
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

[PATCH 1/8] MX25: put define for OTG base address in right include

[Eric Bénard]

Hi Sascha,

Le 10/06/2010 08:36, Sascha Hauer a ?crit :
> applied all but the last one which needs another patch.
>
ok, I'm sending the last one to alsa-devel.

Thanks
Eric