linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: ben-linux@fluff.org (Ben Dooks)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 11/11] USB: s3c-hsotg: Fix OUT packet request retry
Date: Fri, 11 Jun 2010 09:20:57 +0100	[thread overview]
Message-ID: <1276244457-4072-12-git-send-email-ben-linux@fluff.org> (raw)
In-Reply-To: <1276244457-4072-1-git-send-email-ben-linux@fluff.org>

If there is more data in the request than we could fit into a single
hardware request, then check when the OutDone event is received if
we have more data, and if so, schedule the new data instead of trying
to complete the request (and in the case of EP0, sending a 0 packet
in the middle of a transfer).

Also, move the debug message about the current transfer state before
the warning about a bad transfer.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/usb/gadget/s3c-hsotg.c |   18 +++++++++++-------
 1 files changed, 11 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index b34a05d..3da45f5 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -1384,6 +1384,9 @@ static void s3c_hsotg_rx_data(struct s3c_hsotg *hsotg, int ep_idx, int size)
 	read_ptr = hs_req->req.actual;
 	max_req = hs_req->req.length - read_ptr;
 
+	dev_dbg(hsotg->dev, "%s: read %d/%d, done %d/%d\n",
+		__func__, to_read, max_req, read_ptr, hs_req->req.length);
+
 	if (to_read > max_req) {
 		/* more data appeared than we where willing
 		 * to deal with in this request.
@@ -1393,9 +1396,6 @@ static void s3c_hsotg_rx_data(struct s3c_hsotg *hsotg, int ep_idx, int size)
 		WARN_ON_ONCE(1);
 	}
 
-	dev_dbg(hsotg->dev, "%s: read %d/%d, done %d/%d\n",
-		__func__, to_read, max_req, read_ptr, hs_req->req.length);
-
 	hs_ep->total_data += to_read;
 	hs_req->req.actual += to_read;
 	to_read = DIV_ROUND_UP(to_read, 4);
@@ -1464,9 +1464,11 @@ static void s3c_hsotg_send_zlp(struct s3c_hsotg *hsotg,
 static void s3c_hsotg_handle_outdone(struct s3c_hsotg *hsotg,
 				     int epnum, bool was_setup)
 {
+	u32 epsize = readl(hsotg->regs + S3C_DOEPTSIZ(epnum));
 	struct s3c_hsotg_ep *hs_ep = &hsotg->eps[epnum];
 	struct s3c_hsotg_req *hs_req = hs_ep->req;
 	struct usb_request *req = &hs_req->req;
+	unsigned size_left = S3C_DxEPTSIZ_XferSize_GET(epsize);
 	int result = 0;
 
 	if (!hs_req) {
@@ -1475,9 +1477,7 @@ static void s3c_hsotg_handle_outdone(struct s3c_hsotg *hsotg,
 	}
 
 	if (using_dma(hsotg)) {
-		u32 epsize = readl(hsotg->regs + S3C_DOEPTSIZ(epnum));
 		unsigned size_done;
-		unsigned size_left;
 
 		/* Calculate the size of the transfer by checking how much
 		 * is left in the endpoint size register and then working it
@@ -1487,14 +1487,18 @@ static void s3c_hsotg_handle_outdone(struct s3c_hsotg *hsotg,
 		 * so may overshoot/undershoot the transfer.
 		 */
 
-		size_left = S3C_DxEPTSIZ_XferSize_GET(epsize);
-
 		size_done = hs_ep->size_loaded - size_left;
 		size_done += hs_ep->last_load;
 
 		req->actual = size_done;
 	}
 
+	/* if there is more request to do, schedule new transfer */
+	if (req->actual < req->length && size_left == 0) {
+		s3c_hsotg_start_req(hsotg, hs_ep, hs_req, true);
+		return;
+	}
+
 	if (req->actual < req->length && req->short_not_ok) {
 		dev_dbg(hsotg->dev, "%s: got %d/%d (short not ok) => error\n",
 			__func__, req->actual, req->length);
-- 
1.7.0.4

  parent reply	other threads:[~2010-06-11  8:20 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-06-11  8:20 s3c-hsotg fixes Ben Dooks
2010-06-11  8:20 ` [PATCH 01/11] USB: s3c_hsotg: Add support for external USB clock Ben Dooks
2010-06-11  9:35   ` Marek Szyprowski
2010-06-11  9:46     ` Maurus Cuelenaere
2010-06-11  8:20 ` [PATCH 02/11] USB: s3c-hsotg: Increase TX fifo limit Ben Dooks
2010-06-11  8:20 ` [PATCH 03/11] USB: s3c-hsotg: The NPTX/PTX FIFO sizes are in words, not bytes Ben Dooks
2010-06-11  8:20 ` [PATCH 04/11] USB: s3c-hsotg: Avoid overwriting contents of perodic in 'fifo' Ben Dooks
2010-06-11  8:20 ` [PATCH 05/11] USB: s3c-hsotg: Re-initialise all FIFOs on USB bus reset Ben Dooks
2010-06-11  8:20 ` [PATCH 06/11] USB: s3c-hsotg: Add initial detection and setup for dedicated FIFO mode Ben Dooks
2010-06-11  8:54   ` Maurus Cuelenaere
2010-06-11  8:20 ` [PATCH 07/11] USB: s3c-hsotg: Only load packet per fifo write Ben Dooks
2010-06-11  8:20 ` [PATCH 08/11] USB: s3c-hsotg: Check for new request before enqueing new setup Ben Dooks
2010-06-11  8:20 ` [PATCH 09/11] USB: s3c-hsotg: Fix max EP0 IN request length Ben Dooks
2010-06-11  8:20 ` [PATCH 10/11] USB: s3c-hsotg: Fix the OUT EP0 limit Ben Dooks
2010-06-11  9:01   ` Maurus Cuelenaere
2010-06-11  9:07   ` Marek Szyprowski
2010-06-11  8:20 ` Ben Dooks [this message]
2010-06-11 10:25 ` s3c-hsotg fixes Marek Szyprowski
2010-06-12  3:34   ` Ben Dooks
2010-06-14  5:40     ` Marek Szyprowski

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1276244457-4072-12-git-send-email-ben-linux@fluff.org \
    --to=ben-linux@fluff.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).