From mboxrd@z Thu Jan 1 00:00:00 1970 From: srinidhi.kasagar@stericsson.com (srinidhi) Date: Thu, 29 Jul 2010 18:26:04 +0530 Subject: [PATCH 1/2] ARM: make a common low level IRQ helper macros for GIC based platforms Message-ID: <1280408164.14531.13.camel@bnru03> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org The IRQ helper macros for GIC based platforms are similar. Signed-off-by: srinidhi kasagar Acked-by: Linus Walleij --- arch/arm/include/asm/entry-macro-gic.S | 74 ++++++++++++++++++++ arch/arm/mach-cns3xxx/include/mach/entry-macro.S | 73 +------------------- arch/arm/mach-omap2/include/mach/entry-macro.S | 67 +----------------- arch/arm/mach-realview/include/mach/entry-macro.S | 72 +------------------- arch/arm/mach-ux500/include/mach/entry-macro.S | 77 +-------------------- arch/arm/mach-vexpress/include/mach/entry-macro.S | 68 +------------------ 6 files changed, 81 insertions(+), 350 deletions(-) create mode 100644 arch/arm/include/asm/entry-macro-gic.S diff --git a/arch/arm/include/asm/entry-macro-gic.S b/arch/arm/include/asm/entry-macro-gic.S new file mode 100644 index 0000000..85269ca --- /dev/null +++ b/arch/arm/include/asm/entry-macro-gic.S @@ -0,0 +1,74 @@ +/* + * Low-level IRQ helper macros for GIC based platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ +#include + + .macro disable_fiq + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =gic_cpu_base_addr + ldr \base, [\base] + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + /* + * The interrupt numbering scheme is defined in the + * interrupt controller spec. To wit: + * + * Interrupts 0-15 are IPI + * 16-28 are reserved + * 29-31 are local. We allow 30 to be used for the watchdog. + * 32-1020 are global + * 1021-1022 are reserved + * 1023 is "spurious" (no interrupt) + * + * For now, we ignore all local interrupts so only return an interrupt if it's + * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs. + * + * A simple read from the controller will tell us the number of the highest + * priority enabled interrupt. We then just need to check whether it is in the + * valid range for an IRQ (30-1020 inclusive). + */ + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */ + ldr \tmp, =1021 + bic \irqnr, \irqstat, #0x1c00 + cmp \irqnr, #29 + cmpcc \irqnr, \irqnr + cmpne \irqnr, \tmp + cmpcs \irqnr, \irqnr + .endm + + /* + * We assume that irqstat (the raw value of the IRQ acknowledge + * register) is preserved from the macro above. + * If there is an IPI, we immediately signal end of interrupt on the + * controller, since this requires the original irqstat value which + * we won't easily be able to recreate later. + */ + + .macro test_for_ipi, irqnr, irqstat, base, tmp + bic \irqnr, \irqstat, #0x1c00 + cmp \irqnr, #16 + strcc \irqstat, [\base, #GIC_CPU_EOI] + cmpcs \irqnr, \irqnr + .endm + + /* As above, this assumes that irqstat and base are preserved.. */ + + .macro test_for_ltirq, irqnr, irqstat, base, tmp + bic \irqnr, \irqstat, #0x1c00 + mov \tmp, #0 + cmp \irqnr, #29 + moveq \tmp, #1 + streq \irqstat, [\base, #GIC_CPU_EOI] + cmp \tmp, #0 + .endm diff --git a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S index 5e1c554..18f8cf8 100644 --- a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S +++ b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S @@ -8,75 +8,4 @@ * published by the Free Software Foundation. */ -#include -#include - - .macro disable_fiq - .endm - - .macro get_irqnr_preamble, base, tmp - ldr \base, =gic_cpu_base_addr - ldr \base, [\base] - .endm - - .macro arch_ret_to_user, tmp1, tmp2 - .endm - - /* - * The interrupt numbering scheme is defined in the - * interrupt controller spec. To wit: - * - * Interrupts 0-15 are IPI - * 16-28 are reserved - * 29-31 are local. We allow 30 to be used for the watchdog. - * 32-1020 are global - * 1021-1022 are reserved - * 1023 is "spurious" (no interrupt) - * - * For now, we ignore all local interrupts so only return an interrupt if it's - * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs. - * - * A simple read from the controller will tell us the number of the highest - * priority enabled interrupt. We then just need to check whether it is in the - * valid range for an IRQ (30-1020 inclusive). - */ - - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - - ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */ - - ldr \tmp, =1021 - - bic \irqnr, \irqstat, #0x1c00 - - cmp \irqnr, #29 - cmpcc \irqnr, \irqnr - cmpne \irqnr, \tmp - cmpcs \irqnr, \irqnr - - .endm - - /* We assume that irqstat (the raw value of the IRQ acknowledge - * register) is preserved from the macro above. - * If there is an IPI, we immediately signal end of interrupt on the - * controller, since this requires the original irqstat value which - * we won't easily be able to recreate later. - */ - - .macro test_for_ipi, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #16 - strcc \irqstat, [\base, #GIC_CPU_EOI] - cmpcs \irqnr, \irqnr - .endm - - /* As above, this assumes that irqstat and base are preserved.. */ - - .macro test_for_ltirq, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - mov \tmp, #0 - cmp \irqnr, #29 - moveq \tmp, #1 - streq \irqstat, [\base, #GIC_CPU_EOI] - cmp \tmp, #0 - .endm +#include diff --git a/arch/arm/mach-omap2/include/mach/entry-macro.S b/arch/arm/mach-omap2/include/mach/entry-macro.S index 50fd749..62f2d1a 100644 --- a/arch/arm/mach-omap2/include/mach/entry-macro.S +++ b/arch/arm/mach-omap2/include/mach/entry-macro.S @@ -27,11 +27,13 @@ #define INTCPS_SIR_IRQ_OFFSET 0x0040 /* omap2/3 active interrupt offset */ #define ACTIVEIRQ_MASK 0x7f /* omap2/3 active interrupt bits */ +#if defined(CONFIG_ARCH_OMAP4) && !defined(CONFIG_SMP) .macro disable_fiq .endm .macro arch_ret_to_user, tmp1, tmp2 .endm +#endif /* * Unoptimized irq functions for multi-omap2, 3 and 4 @@ -141,70 +143,7 @@ omap_irq_base: .word 0 #ifdef CONFIG_ARCH_OMAP4 - - .macro get_irqnr_preamble, base, tmp - ldr \base, =OMAP4_IRQ_BASE - .endm - - /* - * The interrupt numbering scheme is defined in the - * interrupt controller spec. To wit: - * - * Interrupts 0-15 are IPI - * 16-28 are reserved - * 29-31 are local. We allow 30 to be used for the watchdog. - * 32-1020 are global - * 1021-1022 are reserved - * 1023 is "spurious" (no interrupt) - * - * For now, we ignore all local interrupts so only return an - * interrupt if it's between 30 and 1020. The test_for_ipi - * routine below will pick up on IPIs. - * A simple read from the controller will tell us the number - * of the highest priority enabled interrupt. - * We then just need to check whether it is in the - * valid range for an IRQ (30-1020 inclusive). - */ - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \irqstat, [\base, #GIC_CPU_INTACK] - - ldr \tmp, =1021 - - bic \irqnr, \irqstat, #0x1c00 - - cmp \irqnr, #29 - cmpcc \irqnr, \irqnr - cmpne \irqnr, \tmp - cmpcs \irqnr, \irqnr - .endm - - /* We assume that irqstat (the raw value of the IRQ acknowledge - * register) is preserved from the macro above. - * If there is an IPI, we immediately signal end of interrupt - * on the controller, since this requires the original irqstat - * value which we won't easily be able to recreate later. - */ - - .macro test_for_ipi, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #16 - it cc - strcc \irqstat, [\base, #GIC_CPU_EOI] - it cs - cmpcs \irqnr, \irqnr - .endm - - /* As above, this assumes that irqstat and base are preserved */ - - .macro test_for_ltirq, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - mov \tmp, #0 - cmp \irqnr, #29 - itt eq - moveq \tmp, #1 - streq \irqstat, [\base, #GIC_CPU_EOI] - cmp \tmp, #0 - .endm +#include #endif #endif /* MULTI_OMAP2 */ diff --git a/arch/arm/mach-realview/include/mach/entry-macro.S b/arch/arm/mach-realview/include/mach/entry-macro.S index 340a5c2..e6cc5d5 100644 --- a/arch/arm/mach-realview/include/mach/entry-macro.S +++ b/arch/arm/mach-realview/include/mach/entry-macro.S @@ -7,75 +7,5 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ -#include -#include - .macro disable_fiq - .endm - - .macro get_irqnr_preamble, base, tmp - ldr \base, =gic_cpu_base_addr - ldr \base, [\base] - .endm - - .macro arch_ret_to_user, tmp1, tmp2 - .endm - - /* - * The interrupt numbering scheme is defined in the - * interrupt controller spec. To wit: - * - * Interrupts 0-15 are IPI - * 16-28 are reserved - * 29-31 are local. We allow 30 to be used for the watchdog. - * 32-1020 are global - * 1021-1022 are reserved - * 1023 is "spurious" (no interrupt) - * - * For now, we ignore all local interrupts so only return an interrupt if it's - * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs. - * - * A simple read from the controller will tell us the number of the highest - * priority enabled interrupt. We then just need to check whether it is in the - * valid range for an IRQ (30-1020 inclusive). - */ - - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - - ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */ - - ldr \tmp, =1021 - - bic \irqnr, \irqstat, #0x1c00 - - cmp \irqnr, #29 - cmpcc \irqnr, \irqnr - cmpne \irqnr, \tmp - cmpcs \irqnr, \irqnr - - .endm - - /* We assume that irqstat (the raw value of the IRQ acknowledge - * register) is preserved from the macro above. - * If there is an IPI, we immediately signal end of interrupt on the - * controller, since this requires the original irqstat value which - * we won't easily be able to recreate later. - */ - - .macro test_for_ipi, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #16 - strcc \irqstat, [\base, #GIC_CPU_EOI] - cmpcs \irqnr, \irqnr - .endm - - /* As above, this assumes that irqstat and base are preserved.. */ - - .macro test_for_ltirq, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - mov \tmp, #0 - cmp \irqnr, #29 - moveq \tmp, #1 - streq \irqstat, [\base, #GIC_CPU_EOI] - cmp \tmp, #0 - .endm +#include diff --git a/arch/arm/mach-ux500/include/mach/entry-macro.S b/arch/arm/mach-ux500/include/mach/entry-macro.S index 60ea88d..b778124 100644 --- a/arch/arm/mach-ux500/include/mach/entry-macro.S +++ b/arch/arm/mach-ux500/include/mach/entry-macro.S @@ -10,80 +10,5 @@ * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ -#include -#include - .macro disable_fiq - .endm - - .macro get_irqnr_preamble, base, tmp - ldr \base, =IO_ADDRESS(UX500_GIC_CPU_BASE) - .endm - - .macro arch_ret_to_user, tmp1, tmp2 - .endm - - /* - * The interrupt numbering scheme is defined in the - * interrupt controller spec. To wit: - * - * Interrupts 0-15 are IPI - * 16-28 are reserved - * 29-31 are local. We allow 30 to be used for the watchdog. - * 32-1020 are global - * 1021-1022 are reserved - * 1023 is "spurious" (no interrupt) - * - * For now, we ignore all local interrupts so only return an - * interrupt if it's between 30 and 1020. The test_for_ipi - * routine below will pick up on IPIs. - * - * A simple read from the controller will tell us the number - * of the highest priority enabled interrupt. We then just - * need to check whether it is in the valid range for an - * IRQ (30-1020 inclusive). - */ - - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - - /* bits 12-10 = src CPU, 9-0 = int # */ - ldr \irqstat, [\base, #GIC_CPU_INTACK] - - ldr \tmp, =1021 - - bic \irqnr, \irqstat, #0x1c00 - - cmp \irqnr, #29 - cmpcc \irqnr, \irqnr - cmpne \irqnr, \tmp - cmpcs \irqnr, \irqnr - - .endm - - /* We assume that irqstat (the raw value of the IRQ - * acknowledge register) is preserved from the macro above. - * If there is an IPI, we immediately signal end of - * interrupt on the controller, since this requires the - * original irqstat value which we won't easily be able - * to recreate later. - */ - - .macro test_for_ipi, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #16 - strcc \irqstat, [\base, #GIC_CPU_EOI] - cmpcs \irqnr, \irqnr - .endm - - /* As above, this assumes that irqstat and base - * are preserved.. - */ - - .macro test_for_ltirq, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - mov \tmp, #0 - cmp \irqnr, #29 - moveq \tmp, #1 - streq \irqstat, [\base, #GIC_CPU_EOI] - cmp \tmp, #0 - .endm +#include diff --git a/arch/arm/mach-vexpress/include/mach/entry-macro.S b/arch/arm/mach-vexpress/include/mach/entry-macro.S index 20e9fb5..789895e 100644 --- a/arch/arm/mach-vexpress/include/mach/entry-macro.S +++ b/arch/arm/mach-vexpress/include/mach/entry-macro.S @@ -1,67 +1 @@ -#include - - .macro disable_fiq - .endm - - .macro get_irqnr_preamble, base, tmp - ldr \base, =gic_cpu_base_addr - ldr \base, [\base] - .endm - - .macro arch_ret_to_user, tmp1, tmp2 - .endm - - /* - * The interrupt numbering scheme is defined in the - * interrupt controller spec. To wit: - * - * Interrupts 0-15 are IPI - * 16-28 are reserved - * 29-31 are local. We allow 30 to be used for the watchdog. - * 32-1020 are global - * 1021-1022 are reserved - * 1023 is "spurious" (no interrupt) - * - * For now, we ignore all local interrupts so only return an interrupt if it's - * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs. - * - * A simple read from the controller will tell us the number of the highest - * priority enabled interrupt. We then just need to check whether it is in the - * valid range for an IRQ (30-1020 inclusive). - */ - - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */ - ldr \tmp, =1021 - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #29 - cmpcc \irqnr, \irqnr - cmpne \irqnr, \tmp - cmpcs \irqnr, \irqnr - .endm - - /* We assume that irqstat (the raw value of the IRQ acknowledge - * register) is preserved from the macro above. - * If there is an IPI, we immediately signal end of interrupt on the - * controller, since this requires the original irqstat value which - * we won't easily be able to recreate later. - */ - - .macro test_for_ipi, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #16 - strcc \irqstat, [\base, #GIC_CPU_EOI] - cmpcs \irqnr, \irqnr - .endm - - /* As above, this assumes that irqstat and base are preserved.. */ - - .macro test_for_ltirq, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - mov \tmp, #0 - cmp \irqnr, #29 - moveq \tmp, #1 - streq \irqstat, [\base, #GIC_CPU_EOI] - cmp \tmp, #0 - .endm - +#include -- 1.6.3.3