From: marek.vasut@gmail.com (Marek Vasut)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 03/13] PXA: PalmTC: Modularize Palm Tungsten|C
Date: Fri, 13 Aug 2010 06:32:34 +0200 [thread overview]
Message-ID: <1281673964-2119-3-git-send-email-marek.vasut@gmail.com> (raw)
In-Reply-To: <1281673964-2119-1-git-send-email-marek.vasut@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
arch/arm/mach-pxa/palmtc.c | 147 ++++++++++++++++++++++++++++++++++---------
1 files changed, 116 insertions(+), 31 deletions(-)
diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c
index ce1104d..7f868d4 100644
--- a/arch/arm/mach-pxa/palmtc.c
+++ b/arch/arm/mach-pxa/palmtc.c
@@ -25,6 +25,7 @@
#include <linux/power_supply.h>
#include <linux/gpio_keys.h>
#include <linux/mtd/physmap.h>
+#include <linux/usb/gpio_vbus.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -116,6 +117,7 @@ static unsigned long palmtc_pin_config[] __initdata = {
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
+#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
static struct pxamci_platform_data palmtc_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.gpio_power = GPIO_NR_PALMTC_SD_POWER,
@@ -124,9 +126,18 @@ static struct pxamci_platform_data palmtc_mci_platform_data = {
.detect_delay_ms = 200,
};
+static void __init palmtc_mmc_init(void)
+{
+ pxa_set_mci_info(&palmtc_mci_platform_data);
+}
+#else
+static inline void palmtc_mmc_init(void) {}
+#endif
+
/******************************************************************************
* GPIO keys
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
static struct gpio_keys_button palmtc_pxa_buttons[] = {
{KEY_F8, GPIO_NR_PALMTC_HOTSYNC_BUTTON, 1, "HotSync Button", EV_KEY, 1},
};
@@ -144,9 +155,18 @@ static struct platform_device palmtc_pxa_keys = {
},
};
+static void __init palmtc_keys_init(void)
+{
+ platform_device_register(&palmtc_pxa_keys);
+}
+#else
+static inline void palmtc_keys_init(void) {}
+#endif
+
/******************************************************************************
* Backlight
******************************************************************************/
+#if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE)
static int palmtc_backlight_init(struct device *dev)
{
int ret;
@@ -196,17 +216,35 @@ static struct platform_device palmtc_backlight = {
},
};
+static void __init palmtc_pwm_init(void)
+{
+ platform_device_register(&palmtc_backlight);
+}
+#else
+static inline void palmtc_pwm_init(void) {}
+#endif
+
/******************************************************************************
* IrDA
******************************************************************************/
+#if defined(CONFIG_IRDA) || defined(CONFIG_IRDA_MODULE)
static struct pxaficp_platform_data palmtc_ficp_platform_data = {
.gpio_pwdown = GPIO_NR_PALMTC_IR_DISABLE,
.transceiver_cap = IR_SIRMODE | IR_OFF,
};
+static void __init palmtc_irda_init(void)
+{
+ pxa_set_ficp_info(&palmtc_ficp_platform_data);
+}
+#else
+static inline void palmtc_irda_init(void) {}
+#endif
+
/******************************************************************************
* Keyboard
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE)
static const uint32_t palmtc_matrix_keys[] = {
KEY(0, 0, KEY_F1),
KEY(0, 1, KEY_X),
@@ -290,27 +328,63 @@ static struct platform_device palmtc_keyboard = {
.platform_data = &palmtc_keypad_platform_data,
},
};
+static void __init palmtc_mkp_init(void)
+{
+ platform_device_register(&palmtc_keyboard);
+}
+#else
+static inline void palmtc_mkp_init(void) {}
+#endif
/******************************************************************************
* UDC
******************************************************************************/
-static struct pxa2xx_udc_mach_info palmtc_udc_info __initdata = {
+#if defined(CONFIG_USB_GADGET_PXA25X)||defined(CONFIG_USB_GADGET_PXA25X_MODULE)
+static struct gpio_vbus_mach_info palmtc_udc_info = {
.gpio_vbus = GPIO_NR_PALMTC_USB_DETECT_N,
.gpio_vbus_inverted = 1,
.gpio_pullup = GPIO_NR_PALMTC_USB_POWER,
};
+static struct platform_device palmtc_gpio_vbus = {
+ .name = "gpio-vbus",
+ .id = -1,
+ .dev = {
+ .platform_data = &palmtc_udc_info,
+ },
+};
+
+static void __init palmtc_udc_init(void)
+{
+ platform_device_register(&palmtc_gpio_vbus);
+};
+#else
+static inline void palmtc_udc_init(void) {}
+#endif
+
/******************************************************************************
* Touchscreen / Battery / GPIO-extender
******************************************************************************/
-static struct platform_device palmtc_ucb1400_core = {
+#if defined(CONFIG_TOUCHSCREEN_UCB1400) || \
+ defined(CONFIG_TOUCHSCREEN_UCB1400_MODULE)
+static struct platform_device palmtc_ucb1400_device = {
.name = "ucb1400_core",
.id = -1,
};
+static void __init palmtc_ts_init(void)
+{
+ pxa_set_ac97_info(NULL);
+ platform_device_register(&palmtc_ucb1400_device);
+}
+#else
+static inline void palmtc_ts_init(void) {}
+#endif
+
/******************************************************************************
* NOR Flash
******************************************************************************/
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
static struct resource palmtc_flash_resource = {
.start = PXA_CS0_PHYS,
.end = PXA_CS0_PHYS + SZ_16M - 1,
@@ -356,24 +430,33 @@ static struct platform_device palmtc_flash = {
},
};
+static void __init palmtc_nor_init(void)
+{
+ platform_device_register(&palmtc_flash);
+}
+#else
+static inline void palmtc_nor_init(void) {}
+#endif
+
/******************************************************************************
* Framebuffer
******************************************************************************/
+#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
static struct pxafb_mode_info palmtc_lcd_modes[] = {
-{
- .pixclock = 115384,
- .xres = 320,
- .yres = 320,
- .bpp = 16,
-
- .left_margin = 27,
- .right_margin = 7,
- .upper_margin = 7,
- .lower_margin = 8,
-
- .hsync_len = 6,
- .vsync_len = 1,
-},
+ {
+ .pixclock = 115384,
+ .xres = 320,
+ .yres = 320,
+ .bpp = 16,
+
+ .left_margin = 27,
+ .right_margin = 7,
+ .upper_margin = 7,
+ .lower_margin = 8,
+
+ .hsync_len = 6,
+ .vsync_len = 1,
+ },
};
static struct pxafb_mach_info palmtc_lcd_screen = {
@@ -382,17 +465,17 @@ static struct pxafb_mach_info palmtc_lcd_screen = {
.lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
};
+static void __init palmtc_lcd_init(void)
+{
+ set_pxa_fb_info(&palmtc_lcd_screen);
+}
+#else
+static inline void palmtc_lcd_init(void) {}
+#endif
+
/******************************************************************************
* Machine init
******************************************************************************/
-static struct platform_device *devices[] __initdata = {
- &palmtc_backlight,
- &palmtc_ucb1400_core,
- &palmtc_keyboard,
- &palmtc_pxa_keys,
- &palmtc_flash,
-};
-
static void __init palmtc_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtc_pin_config));
@@ -402,13 +485,15 @@ static void __init palmtc_init(void)
pxa_set_stuart_info(NULL);
pxa_set_hwuart_info(NULL);
- set_pxa_fb_info(&palmtc_lcd_screen);
- pxa_set_mci_info(&palmtc_mci_platform_data);
- pxa_set_udc_info(&palmtc_udc_info);
- pxa_set_ac97_info(NULL);
- pxa_set_ficp_info(&palmtc_ficp_platform_data);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
+ palmtc_mmc_init();
+ palmtc_keys_init();
+ palmtc_pwm_init();
+ palmtc_irda_init();
+ palmtc_mkp_init();
+ palmtc_udc_init();
+ palmtc_ts_init();
+ palmtc_nor_init();
+ palmtc_lcd_init();
};
MACHINE_START(PALMTC, "Palm Tungsten|C")
--
1.7.1
next prev parent reply other threads:[~2010-08-13 4:32 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-08-13 4:32 [PATCH 01/13] Balloon3: Disperse MFP config Marek Vasut
2010-08-13 4:32 ` [PATCH 02/13] PXA: Vpac270: Fix gpio_power for MMC Marek Vasut
2010-08-13 4:32 ` Marek Vasut [this message]
2010-08-13 4:32 ` [PATCH 04/13] UCB1400: Pass ucb1400-gpio data through ac97 bus Marek Vasut
2010-08-13 4:32 ` [PATCH 05/13] PXA: Vpac270: Correct touch IRQ passing to UCB1400 Marek Vasut
2010-08-13 4:32 ` [PATCH 06/13] PXA: PalmTC: Pass GPIO offset to ucb1400-gpio Marek Vasut
2010-08-13 4:32 ` [PATCH 07/13] PXA: PalmTC: Add gpio-leds and vibrator support Marek Vasut
2010-08-13 4:32 ` [PATCH 08/13] PXA: Colibri: Toradex Colibri PXA270 CF support Marek Vasut
2010-08-18 11:43 ` Daniel Mack
2010-08-21 6:22 ` Marek Vasut
2010-08-21 9:33 ` Daniel Mack
2010-09-01 7:23 ` Russell King - ARM Linux
2010-09-01 12:39 ` Marek Vasut
2010-08-13 4:32 ` [PATCH 09/13] PXA: Colibri: Push evalboard MFP into module files Marek Vasut
2010-08-13 4:32 ` [PATCH 10/13] PXA: Colibri: Add M41T00 RTC support Marek Vasut
2010-08-13 4:32 ` [PATCH 11/13] PXA: Colibri: Rename Colibri-evalboard Marek Vasut
2010-08-13 4:32 ` [PATCH 12/13] pxa2xx/pcmcia: Prepare for pxa320 Marek Vasut
2010-08-13 4:32 ` [PATCH 13/13] PXA: Colibri PXA320 PCMCIA driver Marek Vasut
2010-08-18 4:11 ` [PATCH 01/13] Balloon3: Disperse MFP config Eric Miao
2010-08-18 5:05 ` Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1281673964-2119-3-git-send-email-marek.vasut@gmail.com \
--to=marek.vasut@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).