[PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28

linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed

* [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28
@ 2010-12-18 13:39 Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 03/15] ARM: mxs: Add reset routines Shawn Guo
                   ` (8 more replies)
  0 siblings, 9 replies; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

Changes for v7 of this patch series:
 - Use clocksource_register_hz
 - Add mxs namespace for the missing ones
 - Use CLKCTRL_RESET_CHIP over RTC_WATCHDOG to implement arch_reset
 - Define naked pad and introduce validity bits for mA/vol/pull
   to ease the pad modification
 - List all pad definitions at once generated from Freescale
   pinmux Excel sheet
 - Add more comments for timrot instance used for MX23 and MX28
 - Use HW_TIMROT_TIMCOUNTn for v1 to avoid confusion
 - Detect timrot version by reading register HW_TIMROT_VERSION
 - Switch over to use gpiolib __gpio_to_irq()
 - Fix some checkpatch warnings

The full change log could be found in the version history of
following individual patch.

 [PATCH v7 03/15] ARM: mxs: Add reset routines
 [PATCH v7 04/15] ARM: mxs: Add interrupt support
 [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support
 [PATCH v7 06/15] ARM: mxs: Add timer support
 [PATCH v7 07/15] ARM: mxs: Add gpio support
 [PATCH v7 08/15] ARM: mxs: Add iomux support
 [PATCH v7 09/15] ARM: mxs: Add clock support
 [PATCH v7 13/15] ARM: mxs: Add initial mx23evk support
 [PATCH v7 14/15] ARM: mxs: Add initial mx28evk support

Thanks all for the review.

Regards,
Shawn

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 03/15] ARM: mxs: Add reset routines
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 04/15] ARM: mxs: Add interrupt support Shawn Guo
                   ` (7 subsequent siblings)
  8 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

 - The mxs wdog is implemented in RTC block.
 - There is a generic software reset routine for most modules on mxs.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Changes for v7:
 - Use CLKCTRL_RESET_CHIP over RTC_WATCHDOG to implement arch_reset

Changes for v6:
 - Use __mxs_setl() and __mxs_clrl() for bit set/clear

Changes for v4:
 - Add blank line above comment to make the code easy to read
 - Tell compiler unlikely(ret)
 - Make mxs_arch_reset_init __initcall

Changes for v3:
 - Change wdog timeout to 10ms for safety
 - Simplify function mxs_reset_block() to get it look better

Changes for v2:
 - Move rtc clock enabling from arch_reset() into mxs_arch_reset_init()

 arch/arm/mach-mxs/include/mach/system.h |   27 ++++++
 arch/arm/mach-mxs/system.c              |  137 +++++++++++++++++++++++++++++++
 2 files changed, 164 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/include/mach/system.h
 create mode 100644 arch/arm/mach-mxs/system.c

diff --git a/arch/arm/mach-mxs/include/mach/system.h b/arch/arm/mach-mxs/include/mach/system.h
new file mode 100644
index 0000000..0e42823
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/system.h
@@ -0,0 +1,27 @@
+/*
+ *  Copyright (C) 1999 ARM Limited
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd
+ *  Copyright 2004-2008 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MACH_MXS_SYSTEM_H__
+#define __MACH_MXS_SYSTEM_H__
+
+static inline void arch_idle(void)
+{
+	cpu_do_idle();
+}
+
+void arch_reset(char mode, const char *cmd);
+
+#endif /* __MACH_MXS_SYSTEM_H__ */
diff --git a/arch/arm/mach-mxs/system.c b/arch/arm/mach-mxs/system.c
new file mode 100644
index 0000000..9343d7e
--- /dev/null
+++ b/arch/arm/mach-mxs/system.c
@@ -0,0 +1,137 @@
+/*
+ * Copyright (C) 1999 ARM Limited
+ * Copyright (C) 2000 Deep Blue Solutions Ltd
+ * Copyright 2006-2007,2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2008 Juergen Beisert, kernel at pengutronix.de
+ * Copyright 2009 Ilya Yanok, Emcraft Systems Ltd, yanok at emcraft.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+
+#include <asm/proc-fns.h>
+#include <asm/system.h>
+
+#include <mach/mxs.h>
+#include <mach/common.h>
+
+#define MX23_CLKCTRL_RESET_OFFSET	0x120
+#define MX28_CLKCTRL_RESET_OFFSET	0x1e0
+#define MXS_CLKCTRL_RESET_CHIP		(1 << 1)
+
+#define MXS_MODULE_CLKGATE		(1 << 30)
+#define MXS_MODULE_SFTRST		(1 << 31)
+
+static void __iomem *mxs_clkctrl_reset_addr;
+
+/*
+ * Reset the system. It is called by machine_restart().
+ */
+void arch_reset(char mode, const char *cmd)
+{
+	/* reset the chip */
+	__mxs_setl(MXS_CLKCTRL_RESET_CHIP, mxs_clkctrl_reset_addr);
+
+	pr_err("Failed to assert the chip reset\n");
+
+	/* Delay to allow the serial port to show the message */
+	mdelay(50);
+
+	/* We'll take a jump through zero as a poor second */
+	cpu_reset(0);
+}
+
+static int __init mxs_arch_reset_init(void)
+{
+	struct clk *clk;
+
+	mxs_clkctrl_reset_addr = MXS_IO_ADDRESS(MXS_CLKCTRL_BASE_ADDR) +
+				(cpu_is_mx23() ? MX23_CLKCTRL_RESET_OFFSET :
+						 MX28_CLKCTRL_RESET_OFFSET);
+
+	clk = clk_get_sys("rtc", NULL);
+	if (!IS_ERR(clk))
+		clk_enable(clk);
+
+	return 0;
+}
+core_initcall(mxs_arch_reset_init);
+
+/*
+ * Clear the bit and poll it cleared.  This is usually called with
+ * a reset address and mask being either SFTRST(bit 31) or CLKGATE
+ * (bit 30).
+ */
+static int clear_poll_bit(void __iomem *addr, u32 mask)
+{
+	int timeout = 0x400;
+
+	/* clear the bit */
+	__mxs_clrl(mask, addr);
+
+	/*
+	 * SFTRST needs 3 GPMI clocks to settle, the reference manual
+	 * recommends to wait 1us.
+	 */
+	udelay(1);
+
+	/* poll the bit becoming clear */
+	while ((__raw_readl(addr) & mask) && --timeout)
+		/* nothing */;
+
+	return !timeout;
+}
+
+int mxs_reset_block(void __iomem *reset_addr)
+{
+	int ret;
+	int timeout = 0x400;
+
+	/* clear and poll SFTRST */
+	ret = clear_poll_bit(reset_addr, MXS_MODULE_SFTRST);
+	if (unlikely(ret))
+		goto error;
+
+	/* clear CLKGATE */
+	__mxs_clrl(MXS_MODULE_CLKGATE, reset_addr);
+
+	/* set SFTRST to reset the block */
+	__mxs_setl(MXS_MODULE_SFTRST, reset_addr);
+	udelay(1);
+
+	/* poll CLKGATE becoming set */
+	while ((!(__raw_readl(reset_addr) & MXS_MODULE_CLKGATE)) && --timeout)
+		/* nothing */;
+	if (unlikely(!timeout))
+		goto error;
+
+	/* clear and poll SFTRST */
+	ret = clear_poll_bit(reset_addr, MXS_MODULE_SFTRST);
+	if (unlikely(ret))
+		goto error;
+
+	/* clear and poll CLKGATE */
+	ret = clear_poll_bit(reset_addr, MXS_MODULE_CLKGATE);
+	if (unlikely(ret))
+		goto error;
+
+	return 0;
+
+error:
+	pr_err("%s(%p): module reset timeout\n", __func__, reset_addr);
+	return -ETIMEDOUT;
+}
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v7 04/15] ARM: mxs: Add interrupt support
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 03/15] ARM: mxs: Add reset routines Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support Shawn Guo
                   ` (6 subsequent siblings)
  8 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

Add Interrupt Collector (ICOLL) support for MXS-based.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Change for v7:
 - Add namespace for ICOLL_VBASE

Changes for v3:
 - icoll.c: add #include <linux/io.h> as it's removed from mx23.h
   and mx28.h
 - Change inclusion of hardware.h to mxs.h
 - Move writing to HW_ICOLL_VECTOR from icoll.c icoll_ack_irq()
   into entry-macro.S get_irqnr_and_base
 - icoll.c: add more words into comments for level 0 irq ack
 - mx23 and mx28 share the same icoll base address, so hard-coding
   of the address is ok
 - entry-macro.S: define and use HW_ICOLL_STAT_OFFSET over 0x70

Changes for v2:
 - Get icoll base in get_irqnr_preamble
 - Check the case of single SoC build and use hard-coding address if possible

 arch/arm/mach-mxs/icoll.c                    |   81 ++++++++++++++++++++++++++
 arch/arm/mach-mxs/include/mach/entry-macro.S |   41 +++++++++++++
 2 files changed, 122 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/icoll.c
 create mode 100644 arch/arm/mach-mxs/include/mach/entry-macro.S

diff --git a/arch/arm/mach-mxs/icoll.c b/arch/arm/mach-mxs/icoll.c
new file mode 100644
index 0000000..5dd43ba
--- /dev/null
+++ b/arch/arm/mach-mxs/icoll.c
@@ -0,0 +1,81 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+
+#include <mach/mxs.h>
+#include <mach/common.h>
+
+#define HW_ICOLL_VECTOR				0x0000
+#define HW_ICOLL_LEVELACK			0x0010
+#define HW_ICOLL_CTRL				0x0020
+#define HW_ICOLL_INTERRUPTn_SET(n)		(0x0124 + (n) * 0x10)
+#define HW_ICOLL_INTERRUPTn_CLR(n)		(0x0128 + (n) * 0x10)
+#define BM_ICOLL_INTERRUPTn_ENABLE		0x00000004
+#define BV_ICOLL_LEVELACK_IRQLEVELACK__LEVEL0	0x1
+
+static void __iomem *icoll_base = MXS_IO_ADDRESS(MXS_ICOLL_BASE_ADDR);
+
+static void icoll_ack_irq(unsigned int irq)
+{
+	/*
+	 * The Interrupt Collector is able to prioritize irqs.
+	 * Currently only level 0 is used. So acking can use
+	 * BV_ICOLL_LEVELACK_IRQLEVELACK__LEVEL0 unconditionally.
+	 */
+	__raw_writel(BV_ICOLL_LEVELACK_IRQLEVELACK__LEVEL0,
+			icoll_base + HW_ICOLL_LEVELACK);
+}
+
+static void icoll_mask_irq(unsigned int irq)
+{
+	__raw_writel(BM_ICOLL_INTERRUPTn_ENABLE,
+			icoll_base + HW_ICOLL_INTERRUPTn_CLR(irq));
+}
+
+static void icoll_unmask_irq(unsigned int irq)
+{
+	__raw_writel(BM_ICOLL_INTERRUPTn_ENABLE,
+			icoll_base + HW_ICOLL_INTERRUPTn_SET(irq));
+}
+
+static struct irq_chip mxs_icoll_chip = {
+	.ack = icoll_ack_irq,
+	.mask = icoll_mask_irq,
+	.unmask = icoll_unmask_irq,
+};
+
+void __init icoll_init_irq(void)
+{
+	int i;
+
+	/*
+	 * Interrupt Collector reset, which initializes the priority
+	 * for each irq to level 0.
+	 */
+	mxs_reset_block(icoll_base + HW_ICOLL_CTRL);
+
+	for (i = 0; i < MXS_INTERNAL_IRQS; i++) {
+		set_irq_chip(i, &mxs_icoll_chip);
+		set_irq_handler(i, handle_level_irq);
+		set_irq_flags(i, IRQF_VALID);
+	}
+}
diff --git a/arch/arm/mach-mxs/include/mach/entry-macro.S b/arch/arm/mach-mxs/include/mach/entry-macro.S
new file mode 100644
index 0000000..9f0da12
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/entry-macro.S
@@ -0,0 +1,41 @@
+/*
+ * Low-level IRQ helper macros for Freescale MXS-based
+ *
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <mach/mxs.h>
+
+#define MXS_ICOLL_VBASE		MXS_IO_ADDRESS(MXS_ICOLL_BASE_ADDR)
+#define HW_ICOLL_STAT_OFFSET	0x70
+
+	.macro	disable_fiq
+	.endm
+
+	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+	ldr	\irqnr, [\base, #HW_ICOLL_STAT_OFFSET]
+	cmp	\irqnr, #0x7F
+	strne	\irqnr, [\base]
+	moveqs	\irqnr, #0
+	.endm
+
+	.macro  get_irqnr_preamble, base, tmp
+	ldr	\base, =MXS_ICOLL_VBASE
+	.endm
+
+	.macro  arch_ret_to_user, tmp1, tmp2
+	.endm
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 03/15] ARM: mxs: Add reset routines Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 04/15] ARM: mxs: Add interrupt support Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  2010-12-20 11:50   ` Wolfram Sang
  2010-12-18 13:39 ` [PATCH v7 06/15] ARM: mxs: Add timer support Shawn Guo
                   ` (5 subsequent siblings)
  8 siblings, 1 reply; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

 - DEBUG_LL support, which is incompatible with multi-soc MXS image
   because of different DUART base address on MX23 and MX28
 - uncompress message support

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Changes for v7:
 - Add namespace for uart_base and UART()

Changes for v3:
 - debug-macro.S: change inclusion of hardware.h to mx23.h plus mx28.h
 - Remove #define __MXS_BOOT_UNCOMPRESS
 - Add namespace MXS_DUART_ for macros
 - Add comment "If it's not, the output is simply discarded."

Changes for v2:
 - Remove incorrect comments

 arch/arm/mach-mxs/include/mach/debug-macro.S |   52 ++++++++++++++++++
 arch/arm/mach-mxs/include/mach/uncompress.h  |   76 ++++++++++++++++++++++++++
 2 files changed, 128 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/include/mach/debug-macro.S
 create mode 100644 arch/arm/mach-mxs/include/mach/uncompress.h

diff --git a/arch/arm/mach-mxs/include/mach/debug-macro.S b/arch/arm/mach-mxs/include/mach/debug-macro.S
new file mode 100644
index 0000000..a1522fd
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/debug-macro.S
@@ -0,0 +1,52 @@
+/* arch/arm/mach-mxs/include/mach/debug-macro.S
+ *
+ * Debugging macro include header
+ *
+ *  Copyright (C) 1994-1999 Russell King
+ *  Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <mach/mx23.h>
+#include <mach/mx28.h>
+
+#ifdef CONFIG_SOC_IMX23
+#ifdef UART_PADDR
+#error "CONFIG_DEBUG_LL is incompatible with multiple archs"
+#endif
+#define UART_PADDR	MX23_DUART_BASE_ADDR
+#endif
+
+#ifdef CONFIG_SOC_IMX28
+#ifdef UART_PADDR
+#error "CONFIG_DEBUG_LL is incompatible with multiple archs"
+#endif
+#define UART_PADDR	MX28_DUART_BASE_ADDR
+#endif
+
+#define UART_VADDR	MXS_IO_ADDRESS(UART_PADDR)
+
+		.macro	addruart, rp, rv
+		ldr	\rp, =UART_PADDR	@ physical
+		ldr	\rv, =UART_VADDR	@ virtual
+		.endm
+
+		.macro	senduart, rd, rx
+		str	\rd, [\rx, #0x0]	@ DR
+		.endm
+
+		.macro	waituart, rd, rx
+1001:		ldr	\rd, [\rx, #0x18]	@ FR
+		tst	\rd, #1 << 5		@ FR_TXFF
+		bne	1001b
+		.endm
+
+		.macro	busyuart, rd, rx
+1002:		ldr	\rd, [\rx, #0x18]	@ FR
+		tst	\rd, #1 << 3		@ FR_BUSY
+		beq	1002b
+		.endm
diff --git a/arch/arm/mach-mxs/include/mach/uncompress.h b/arch/arm/mach-mxs/include/mach/uncompress.h
new file mode 100644
index 0000000..a005e76
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/uncompress.h
@@ -0,0 +1,76 @@
+/*
+ *  arch/arm/mach-mxs/include/mach/uncompress.h
+ *
+ *  Copyright (C) 1999 ARM Limited
+ *  Copyright (C) Shane Nay (shane@minirl.com)
+ *  Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#ifndef __MACH_MXS_UNCOMPRESS_H__
+#define __MACH_MXS_UNCOMPRESS_H__
+
+#include <asm/mach-types.h>
+
+static unsigned long mxs_duart_base;
+
+#define MXS_DUART(x)	(*(volatile unsigned long *)(mxs_duart_base + (x)))
+
+#define MXS_DUART_DR		0x00
+#define MXS_DUART_FR		0x18
+#define MXS_DUART_FR_TXFE	(1 << 7)
+#define MXS_DUART_CR		0x30
+#define MXS_DUART_CR_UARTEN	(1 << 0)
+
+/*
+ * The following code assumes the serial port has already been
+ * initialized by the bootloader. If it's not, the output is
+ * simply discarded.
+ */
+
+static void putc(int ch)
+{
+	if (!mxs_duart_base)
+		return;
+	if (!(MXS_DUART(MXS_DUART_CR) & MXS_DUART_CR_UARTEN))
+		return;
+
+	while (!(MXS_DUART(MXS_DUART_FR) & MXS_DUART_FR_TXFE))
+		barrier();
+
+	MXS_DUART(MXS_DUART_DR) = ch;
+}
+
+static inline void flush(void)
+{
+}
+
+#define MX23_DUART_BASE_ADDR	0x80070000
+#define MX28_DUART_BASE_ADDR	0x80074000
+
+static inline void __arch_decomp_setup(unsigned long arch_id)
+{
+	switch (arch_id) {
+	case MACH_TYPE_MX23EVK:
+		mxs_duart_base = MX23_DUART_BASE_ADDR;
+		break;
+	case MACH_TYPE_MX28EVK:
+		mxs_duart_base = MX28_DUART_BASE_ADDR;
+		break;
+	default:
+		break;
+	}
+}
+
+#define arch_decomp_setup()	__arch_decomp_setup(arch_id)
+#define arch_decomp_wdog()
+
+#endif /* __MACH_MXS_UNCOMPRESS_H__ */
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support
  2010-12-18 13:39 ` [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support Shawn Guo
@ 2010-12-20 11:50   ` Wolfram Sang
  2010-12-20 13:22     ` Shawn Guo
  0 siblings, 1 reply; 18+ messages in thread
From: Wolfram Sang @ 2010-12-20 11:50 UTC (permalink / raw)
  To: linux-arm-kernel

Hi Shawn,

I discovered this weekend that the DUART is just an amba-pl011 which
is already supported in mainline. So we should use the existing
infrastructure here.

On Sat, Dec 18, 2010 at 09:39:29PM +0800, Shawn Guo wrote:

>  - DEBUG_LL support, which is incompatible with multi-soc MXS image
>    because of different DUART base address on MX23 and MX28

We should be able to use the AMBA identification signature to distinguish at
runtime, no?

>  - uncompress message support
> 
> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

>  arch/arm/mach-mxs/include/mach/debug-macro.S |   52 ++++++++++++++++++

We should use asm/hardware/debug-pl01x.S, like the other users:

wsa at katana:~/Kernel/linux-2.6/arch/arm$ g debug-pl01x
include/asm/hardware/debug-pl01x.S:1:/* arch/arm/include/asm/hardware/debug-pl01x.S
mach-cns3xxx/include/mach/debug-macro.S:19:#include <asm/hardware/debug-pl01x.S>
mach-ep93xx/include/mach/debug-macro.S:21:#include <asm/hardware/debug-pl01x.S>
mach-integrator/include/mach/debug-macro.S:20:#include <asm/hardware/debug-pl01x.S>
mach-nomadik/include/mach/debug-macro.S:20:#include <asm/hardware/debug-pl01x.S>
mach-realview/include/mach/debug-macro.S:42:#include <asm/hardware/debug-pl01x.S>
mach-u300/include/mach/debug-macro.S:21:#include <asm/hardware/debug-pl01x.S>
mach-ux500/include/mach/debug-macro.S:26:#include <asm/hardware/debug-pl01x.S>
mach-versatile/include/mach/debug-macro.S:21:#include <asm/hardware/debug-pl01x.S>
mach-vexpress/include/mach/debug-macro.S:21:#include <asm/hardware/debug-pl01x.S>


>  arch/arm/mach-mxs/include/mach/uncompress.h  |   76 ++++++++++++++++++++++++++

Auto-detection could be used here, too?

Kind regards,

   Wolfram

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 198 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20101220/da1846e6/attachment.sig>

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support
  2010-12-20 11:50   ` Wolfram Sang
@ 2010-12-20 13:22     ` Shawn Guo
  2010-12-20 13:55       ` Wolfram Sang
  0 siblings, 1 reply; 18+ messages in thread
From: Shawn Guo @ 2010-12-20 13:22 UTC (permalink / raw)
  To: linux-arm-kernel

On Mon, Dec 20, 2010 at 12:50:59PM +0100, Wolfram Sang wrote:
> Hi Shawn,
> 
> I discovered this weekend that the DUART is just an amba-pl011 which
> is already supported in mainline. So we should use the existing
> infrastructure here.
> 
> On Sat, Dec 18, 2010 at 09:39:29PM +0800, Shawn Guo wrote:
> 
> >  - DEBUG_LL support, which is incompatible with multi-soc MXS image
> >    because of different DUART base address on MX23 and MX28
> 
> We should be able to use the AMBA identification signature to distinguish at
> runtime, no?
> 
> >  - uncompress message support
> > 
> > Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
> 
> >  arch/arm/mach-mxs/include/mach/debug-macro.S |   52 ++++++++++++++++++
> 
> We should use asm/hardware/debug-pl01x.S, like the other users:
> 
> wsa at katana:~/Kernel/linux-2.6/arch/arm$ g debug-pl01x
> include/asm/hardware/debug-pl01x.S:1:/* arch/arm/include/asm/hardware/debug-pl01x.S
> mach-cns3xxx/include/mach/debug-macro.S:19:#include <asm/hardware/debug-pl01x.S>
> mach-ep93xx/include/mach/debug-macro.S:21:#include <asm/hardware/debug-pl01x.S>
> mach-integrator/include/mach/debug-macro.S:20:#include <asm/hardware/debug-pl01x.S>
> mach-nomadik/include/mach/debug-macro.S:20:#include <asm/hardware/debug-pl01x.S>
> mach-realview/include/mach/debug-macro.S:42:#include <asm/hardware/debug-pl01x.S>
> mach-u300/include/mach/debug-macro.S:21:#include <asm/hardware/debug-pl01x.S>
> mach-ux500/include/mach/debug-macro.S:26:#include <asm/hardware/debug-pl01x.S>
> mach-versatile/include/mach/debug-macro.S:21:#include <asm/hardware/debug-pl01x.S>
> mach-vexpress/include/mach/debug-macro.S:21:#include <asm/hardware/debug-pl01x.S>
> 

Just tested it, and it works.  Will do in v8.  Thanks for the comment.

> 
> >  arch/arm/mach-mxs/include/mach/uncompress.h  |   76 ++++++++++++++++++++++++++
> 
> Auto-detection could be used here, too?
> 
I'm afraid not.  How do you expect the detection is done, by reading
some register like we are doing in system.c?  Which register
specifically?  If the register gets different address between
mx23 and mx28, we need to utilize the current mechanism to
distinguish the address anyway.

-- 
Regards,
Shawn

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support
  2010-12-20 13:22     ` Shawn Guo
@ 2010-12-20 13:55       ` Wolfram Sang
  2010-12-20 14:25         ` Shawn Guo
  0 siblings, 1 reply; 18+ messages in thread
From: Wolfram Sang @ 2010-12-20 13:55 UTC (permalink / raw)
  To: linux-arm-kernel


> > We should use asm/hardware/debug-pl01x.S, like the other users:
> 
> Just tested it, and it works.  Will do in v8.  Thanks for the comment.

Cool.

> > 
> > >  arch/arm/mach-mxs/include/mach/uncompress.h  |   76 ++++++++++++++++++++++++++
> > 
> > Auto-detection could be used here, too?
> > 
> I'm afraid not.  How do you expect the detection is done, by reading
> some register like we are doing in system.c?

I am not sure which register you mean in system.c?

> Which register specifically?

The signature of the amba device (base + size - 0x20). You can check
drivers/amba/bus.c how it checks for the signature.

> If the register gets different address between
> mx23 and mx28, we need to utilize the current mechanism to
> distinguish the address anyway.

We could simply test both locations and see where it is present?

Kind regards,

   Wolfram

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 198 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20101220/73f23c53/attachment.sig>

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support
  2010-12-20 13:55       ` Wolfram Sang
@ 2010-12-20 14:25         ` Shawn Guo
  2010-12-20 14:35           ` Wolfram Sang
  0 siblings, 1 reply; 18+ messages in thread
From: Shawn Guo @ 2010-12-20 14:25 UTC (permalink / raw)
  To: linux-arm-kernel

Hi Wolfram,

On Mon, Dec 20, 2010 at 02:55:35PM +0100, Wolfram Sang wrote:
> 
> > > We should use asm/hardware/debug-pl01x.S, like the other users:
> > 
> > Just tested it, and it works.  Will do in v8.  Thanks for the comment.
> 
> Cool.
> 
> > > 
> > > >  arch/arm/mach-mxs/include/mach/uncompress.h  |   76 ++++++++++++++++++++++++++
> > > 
> > > Auto-detection could be used here, too?
> > > 
> > I'm afraid not.  How do you expect the detection is done, by reading
> > some register like we are doing in system.c?
> 
> I am not sure which register you mean in system.c?
> 
> > Which register specifically?
> 
> The signature of the amba device (base + size - 0x20). You can check
> drivers/amba/bus.c how it checks for the signature.
> 
> > If the register gets different address between
> > mx23 and mx28, we need to utilize the current mechanism to
> > distinguish the address anyway.
> 
> We could simply test both locations and see where it is present?
> 
Is there any problem of simply using arch_id here? I do not see
significant benefit of using the detection you suggest here
over the current way.

-- 
Regards,
Shawn

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support
  2010-12-20 14:25         ` Shawn Guo
@ 2010-12-20 14:35           ` Wolfram Sang
  0 siblings, 0 replies; 18+ messages in thread
From: Wolfram Sang @ 2010-12-20 14:35 UTC (permalink / raw)
  To: linux-arm-kernel

Hi Shawn,

> > > I'm afraid not.  How do you expect the detection is done, by reading
> > > some register like we are doing in system.c?
> > 
> > I am not sure which register you mean in system.c?
> > 
> > > Which register specifically?
> > 
> > The signature of the amba device (base + size - 0x20). You can check
> > drivers/amba/bus.c how it checks for the signature.
> > 
> > > If the register gets different address between
> > > mx23 and mx28, we need to utilize the current mechanism to
> > > distinguish the address anyway.
> > 
> > We could simply test both locations and see where it is present?
> > 
> Is there any problem of simply using arch_id here? I do not see
> significant benefit of using the detection you suggest here
> over the current way.

Ah, sorry, I thought you meant auto-detection was not possible in
debug.S as well (and there it is worthwhile so mx23 and mx28 can be
built into one kernel). For uncompress.h, the gain is nothing major,
true. One would save to add custom boards there just to match the base
address, but well...

Kind regards,

   Wolfram

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 198 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20101220/5a6e9cdb/attachment.sig>

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 06/15] ARM: mxs: Add timer support
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
                   ` (2 preceding siblings ...)
  2010-12-18 13:39 ` [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 07/15] ARM: mxs: Add gpio support Shawn Guo
                   ` (4 subsequent siblings)
  8 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

There are 2 versions of the timrot on Freescale MXS-based SoCs.
The v1 on MX23 only gets 16 bits counter, while v2 on MX28
extends the counter to 32 bits.

The implementation uses two timers, one for clock_event and
another for clocksource. MX28 uses timrot 0 and 1, while MX23
uses 0 and 2.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Changes for v7:
 - Use clocksource_register_hz suggested by Rusell
 - Add more comments for timrot instance used for MX23 and MX28
 - Use HW_TIMROT_TIMCOUNTn for v1 to avoid confusion
 - Detect timrot version by reading register HW_TIMROT_VERSION
 - Add namespace for clockevent_device and clockevent_mode
 - Add namespace for timer_base

Changes for v6:
 - Use __mxs_setl() and __mxs_clrl() for bit set/clear

Changes for v4:
 - Change inclusion of hardware.h to mxs.h
 - Use two timers on MX28 also to simpify timrotv2_set_next_event()
 - MX23 and MX28 share the common timrot base address, so it can be
   a hard-assignment.
 - Pass &clockevent_mxs to mxs_timer_interrupt via mxs_timer_irq.dev_id
 - Fix code of setting far-far future
 - Change printk to pr_info and pr_err
 - Change timrotv2 min_delta_ns to 0xf

Changes for v3:
 - Use term clock_event over next_event and clocksource over get_cycles
 - Split BV_TIMROT_TIMCTRLn_SELECT__32KHZ_XTAL into two definitions for v1 and v2 respectively
 - Turn timrot_get_cycles() into timrotv1_get_cycles() and timrotv2_get_cycles()
 - Turn timrot_set_next_event() into timrotv1_set_next_event() and timrotv2_set_next_event()
 - Skip flag IRQF_DISABLED
 - Remove unncessary IRQ disabling in mxs_set_mode()
 - Change shift of clocksource_mxs to 17

Changes for v2:
 - Fix a bug in timrot_set_next_event(). It should read
   HW_TIMROT_RUNNING_COUNTn to get the current counts.

 arch/arm/mach-mxs/timer.c |  296 +++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 296 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/timer.c

diff --git a/arch/arm/mach-mxs/timer.c b/arch/arm/mach-mxs/timer.c
new file mode 100644
index 0000000..13647f3
--- /dev/null
+++ b/arch/arm/mach-mxs/timer.c
@@ -0,0 +1,296 @@
+/*
+ *  Copyright (C) 2000-2001 Deep Blue Solutions
+ *  Copyright (C) 2002 Shane Nay (shane at minirl.com)
+ *  Copyright (C) 2006-2007 Pavel Pisa (ppisa at pikron.com)
+ *  Copyright (C) 2008 Juergen Beisert (kernel at pengutronix.de)
+ *  Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/clockchips.h>
+#include <linux/clk.h>
+
+#include <asm/mach/time.h>
+#include <mach/mxs.h>
+#include <mach/common.h>
+
+/*
+ * There are 2 versions of the timrot on Freescale MXS-based SoCs.
+ * The v1 on MX23 only gets 16 bits counter, while v2 on MX28
+ * extends the counter to 32 bits.
+ *
+ * The implementation uses two timers, one for clock_event and
+ * another for clocksource. MX28 uses timrot 0 and 1, while MX23
+ * uses 0 and 2.
+ */
+
+#define MX23_TIMROT_VERSION_OFFSET	0x0a0
+#define MX28_TIMROT_VERSION_OFFSET	0x120
+#define BP_TIMROT_MAJOR_VERSION		24
+#define BV_TIMROT_VERSION_1		0x01
+#define BV_TIMROT_VERSION_2		0x02
+#define timrot_is_v1()	(timrot_major_version == BV_TIMROT_VERSION_1)
+
+/*
+ * There are 4 registers for each timrotv2 instance, and 2 registers
+ * for each timrotv1. So address step 0x40 in macros below strides
+ * one instance of timrotv2 while two instances of timrotv1.
+ *
+ * As the result, HW_TIMROT_XXXn(1) defines the address of timrot1
+ * on MX28 while timrot2 on MX23.
+ */
+/* common between v1 and v2 */
+#define HW_TIMROT_ROTCTRL		0x00
+#define HW_TIMROT_TIMCTRLn(n)		(0x20 + (n) * 0x40)
+/* v1 only */
+#define HW_TIMROT_TIMCOUNTn(n)		(0x30 + (n) * 0x40)
+/* v2 only */
+#define HW_TIMROT_RUNNING_COUNTn(n)	(0x30 + (n) * 0x40)
+#define HW_TIMROT_FIXED_COUNTn(n)	(0x40 + (n) * 0x40)
+
+#define BM_TIMROT_TIMCTRLn_RELOAD	(1 << 6)
+#define BM_TIMROT_TIMCTRLn_UPDATE	(1 << 7)
+#define BM_TIMROT_TIMCTRLn_IRQ_EN	(1 << 14)
+#define BM_TIMROT_TIMCTRLn_IRQ		(1 << 15)
+#define BP_TIMROT_TIMCTRLn_SELECT	0
+#define BV_TIMROTv1_TIMCTRLn_SELECT__32KHZ_XTAL	0x8
+#define BV_TIMROTv2_TIMCTRLn_SELECT__32KHZ_XTAL	0xb
+
+static struct clock_event_device mxs_clockevent_device;
+static enum clock_event_mode mxs_clockevent_mode = CLOCK_EVT_MODE_UNUSED;
+
+static void __iomem *mxs_timrot_base = MXS_IO_ADDRESS(MXS_TIMROT_BASE_ADDR);
+static u32 timrot_major_version;
+
+static inline void timrot_irq_disable(void)
+{
+	__mxs_clrl(BM_TIMROT_TIMCTRLn_IRQ_EN,
+			mxs_timrot_base + HW_TIMROT_TIMCTRLn(0));
+}
+
+static inline void timrot_irq_enable(void)
+{
+	__mxs_setl(BM_TIMROT_TIMCTRLn_IRQ_EN,
+			mxs_timrot_base + HW_TIMROT_TIMCTRLn(0));
+}
+
+static void timrot_irq_acknowledge(void)
+{
+	__mxs_clrl(BM_TIMROT_TIMCTRLn_IRQ,
+			mxs_timrot_base + HW_TIMROT_TIMCTRLn(0));
+}
+
+static cycle_t timrotv1_get_cycles(struct clocksource *cs)
+{
+	return ~((__raw_readl(mxs_timrot_base + HW_TIMROT_TIMCOUNTn(1))
+			& 0xffff0000) >> 16);
+}
+
+static cycle_t timrotv2_get_cycles(struct clocksource *cs)
+{
+	return ~__raw_readl(mxs_timrot_base + HW_TIMROT_RUNNING_COUNTn(1));
+}
+
+static int timrotv1_set_next_event(unsigned long evt,
+					struct clock_event_device *dev)
+{
+	/* timrot decrements the count */
+	__raw_writel(evt, mxs_timrot_base + HW_TIMROT_TIMCOUNTn(0));
+
+	return 0;
+}
+
+static int timrotv2_set_next_event(unsigned long evt,
+					struct clock_event_device *dev)
+{
+	/* timrot decrements the count */
+	__raw_writel(evt, mxs_timrot_base + HW_TIMROT_FIXED_COUNTn(0));
+
+	return 0;
+}
+
+static irqreturn_t mxs_timer_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *evt = dev_id;
+
+	timrot_irq_acknowledge();
+	evt->event_handler(evt);
+
+	return IRQ_HANDLED;
+}
+
+static struct irqaction mxs_timer_irq = {
+	.name		= "MXS Timer Tick",
+	.dev_id		= &mxs_clockevent_device,
+	.flags		= IRQF_TIMER | IRQF_IRQPOLL,
+	.handler	= mxs_timer_interrupt,
+};
+
+#ifdef DEBUG
+static const char *clock_event_mode_label[] const = {
+	[CLOCK_EVT_MODE_PERIODIC] = "CLOCK_EVT_MODE_PERIODIC",
+	[CLOCK_EVT_MODE_ONESHOT]  = "CLOCK_EVT_MODE_ONESHOT",
+	[CLOCK_EVT_MODE_SHUTDOWN] = "CLOCK_EVT_MODE_SHUTDOWN",
+	[CLOCK_EVT_MODE_UNUSED]   = "CLOCK_EVT_MODE_UNUSED"
+};
+#endif /* DEBUG */
+
+static void mxs_set_mode(enum clock_event_mode mode,
+				struct clock_event_device *evt)
+{
+	/* Disable interrupt in timer module */
+	timrot_irq_disable();
+
+	if (mode != mxs_clockevent_mode) {
+		/* Set event time into the furthest future */
+		if (timrot_is_v1())
+			__raw_writel(0xffff,
+				mxs_timrot_base + HW_TIMROT_TIMCOUNTn(1));
+		else
+			__raw_writel(0xffffffff,
+				mxs_timrot_base + HW_TIMROT_FIXED_COUNTn(1));
+
+		/* Clear pending interrupt */
+		timrot_irq_acknowledge();
+	}
+
+#ifdef DEBUG
+	pr_info("%s: changing mode from %s to %s\n", __func__,
+		clock_event_mode_label[mxs_clockevent_mode],
+		clock_event_mode_label[mode]);
+#endif /* DEBUG */
+
+	/* Remember timer mode */
+	mxs_clockevent_mode = mode;
+
+	switch (mode) {
+	case CLOCK_EVT_MODE_PERIODIC:
+		pr_err("%s: Periodic mode is not implemented\n", __func__);
+		break;
+	case CLOCK_EVT_MODE_ONESHOT:
+		timrot_irq_enable();
+		break;
+	case CLOCK_EVT_MODE_SHUTDOWN:
+	case CLOCK_EVT_MODE_UNUSED:
+	case CLOCK_EVT_MODE_RESUME:
+		/* Left event sources disabled, no more interrupts appear */
+		break;
+	}
+}
+
+static struct clock_event_device mxs_clockevent_device = {
+	.name		= "mxs_timrot",
+	.features	= CLOCK_EVT_FEAT_ONESHOT,
+	.shift		= 32,
+	.set_mode	= mxs_set_mode,
+	.set_next_event	= timrotv2_set_next_event,
+	.rating		= 200,
+};
+
+static int __init mxs_clockevent_init(struct clk *timer_clk)
+{
+	unsigned int c = clk_get_rate(timer_clk);
+
+	mxs_clockevent_device.mult =
+		div_sc(c, NSEC_PER_SEC, mxs_clockevent_device.shift);
+	mxs_clockevent_device.cpumask = cpumask_of(0);
+	if (timrot_is_v1()) {
+		mxs_clockevent_device.set_next_event = timrotv1_set_next_event;
+		mxs_clockevent_device.max_delta_ns =
+			clockevent_delta2ns(0xfffe, &mxs_clockevent_device);
+		mxs_clockevent_device.min_delta_ns =
+			clockevent_delta2ns(0xf, &mxs_clockevent_device);
+	} else {
+		mxs_clockevent_device.max_delta_ns =
+			clockevent_delta2ns(0xfffffffe, &mxs_clockevent_device);
+		mxs_clockevent_device.min_delta_ns =
+			clockevent_delta2ns(0xf, &mxs_clockevent_device);
+	}
+
+	clockevents_register_device(&mxs_clockevent_device);
+
+	return 0;
+}
+
+static struct clocksource clocksource_mxs = {
+	.name		= "mxs_timer",
+	.rating		= 200,
+	.read		= timrotv2_get_cycles,
+	.mask		= CLOCKSOURCE_MASK(32),
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static int __init mxs_clocksource_init(struct clk *timer_clk)
+{
+	unsigned int c = clk_get_rate(timer_clk);
+
+	if (timrot_is_v1()) {
+		clocksource_mxs.read = timrotv1_get_cycles;
+		clocksource_mxs.mask = CLOCKSOURCE_MASK(16);
+	}
+
+	clocksource_register_hz(&clocksource_mxs, c);
+
+	return 0;
+}
+
+void __init mxs_timer_init(struct clk *timer_clk, int irq)
+{
+	clk_enable(timer_clk);
+
+	/*
+	 * Initialize timers to a known state
+	 */
+	mxs_reset_block(mxs_timrot_base + HW_TIMROT_ROTCTRL);
+
+	/* get timrot version */
+	timrot_major_version = __raw_readl(mxs_timrot_base +
+				(cpu_is_mx23() ? MX23_TIMROT_VERSION_OFFSET :
+						MX28_TIMROT_VERSION_OFFSET));
+	timrot_major_version >>= BP_TIMROT_MAJOR_VERSION;
+
+	/* one for clock_event */
+	__raw_writel((timrot_is_v1() ?
+			BV_TIMROTv1_TIMCTRLn_SELECT__32KHZ_XTAL :
+			BV_TIMROTv2_TIMCTRLn_SELECT__32KHZ_XTAL) |
+			BM_TIMROT_TIMCTRLn_UPDATE |
+			BM_TIMROT_TIMCTRLn_IRQ_EN,
+			mxs_timrot_base + HW_TIMROT_TIMCTRLn(0));
+
+	/* another for clocksource */
+	__raw_writel((timrot_is_v1() ?
+			BV_TIMROTv1_TIMCTRLn_SELECT__32KHZ_XTAL :
+			BV_TIMROTv2_TIMCTRLn_SELECT__32KHZ_XTAL) |
+			BM_TIMROT_TIMCTRLn_RELOAD,
+			mxs_timrot_base + HW_TIMROT_TIMCTRLn(1));
+
+	/* set clocksource timer fixed count to the maximum */
+	if (timrot_is_v1())
+		__raw_writel(0xffff,
+			mxs_timrot_base + HW_TIMROT_TIMCOUNTn(1));
+	else
+		__raw_writel(0xffffffff,
+			mxs_timrot_base + HW_TIMROT_FIXED_COUNTn(1));
+
+	/* init and register the timer to the framework */
+	mxs_clocksource_init(timer_clk);
+	mxs_clockevent_init(timer_clk);
+
+	/* Make irqs happen */
+	setup_irq(irq, &mxs_timer_irq);
+}
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v7 07/15] ARM: mxs: Add gpio support
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
                   ` (3 preceding siblings ...)
  2010-12-18 13:39 ` [PATCH v7 06/15] ARM: mxs: Add timer support Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 08/15] ARM: mxs: Add iomux support Shawn Guo
                   ` (3 subsequent siblings)
  8 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

MXS-based SoCs implement gpio support in block PINCTRL.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Changes for v7:
 - Switch over to use gpiolib __gpio_to_irq()

Changes for v6:
 - Use __mxs_setl() and __mxs_clrl() for bit set/clear
 - Rename functions for not using leading underscore
 - Add mxs_ to some functions name to align naming scheme
 - Introduce variables pin_mask and pin_addr to make code look better
 - Remove PINCTRL_PIN2IRQ from irq_stat assignment
 - Add comment for clearing status bit in IRQSTAT
 - Set up irq handler before registering gpio chip

Changes for v5:
 - Leave PIN2IRQ set when disabling gpio IRQ to avoid
   losting interrupt

Changes for v3:
 - include/mach/gpio.h: remove the inclusion of hardware.h
 - gpio.c: change inclusion of hardware.h to mx23.h plus mx28.h
 - Remove spinlock totally since SET/CLE can be used in all the
   gpio register access

Changes for v2:
 - Create arch/arm/mach-mxs/gpio.h to accommodate stuff private for mach-mxs
 - Use GPIO_INT_LEV_MASK and GPIO_INT_POL_MASK instead of constant
 - Remove both edges IRQ support which is not needed
 - Use SET and CLR register of PINCTRL_DOE in _set_gpio_direction()
 - Use pr_info over printk(KERN_INFO)

 arch/arm/mach-mxs/gpio.c              |  325 +++++++++++++++++++++++++++++++++
 arch/arm/mach-mxs/gpio.h              |   34 ++++
 arch/arm/mach-mxs/include/mach/gpio.h |   35 ++++
 3 files changed, 394 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/gpio.c
 create mode 100644 arch/arm/mach-mxs/gpio.h
 create mode 100644 arch/arm/mach-mxs/include/mach/gpio.h

diff --git a/arch/arm/mach-mxs/gpio.c b/arch/arm/mach-mxs/gpio.c
new file mode 100644
index 0000000..d7ad7a6
--- /dev/null
+++ b/arch/arm/mach-mxs/gpio.c
@@ -0,0 +1,325 @@
+/*
+ * MXC GPIO support. (c) 2008 Daniel Mack <daniel@caiaq.de>
+ * Copyright 2008 Juergen Beisert, kernel at pengutronix.de
+ *
+ * Based on code from Freescale,
+ * Copyright (C) 2004-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA  02110-1301, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+#include <mach/mx23.h>
+#include <mach/mx28.h>
+#include <asm-generic/bug.h>
+
+#include "gpio.h"
+
+static struct mxs_gpio_port *mxs_gpio_ports;
+static int gpio_table_size;
+
+#define PINCTRL_DOUT(n)		((cpu_is_mx23() ? 0x0500 : 0x0700) + (n) * 0x10)
+#define PINCTRL_DIN(n)		((cpu_is_mx23() ? 0x0600 : 0x0900) + (n) * 0x10)
+#define PINCTRL_DOE(n)		((cpu_is_mx23() ? 0x0700 : 0x0b00) + (n) * 0x10)
+#define PINCTRL_PIN2IRQ(n)	((cpu_is_mx23() ? 0x0800 : 0x1000) + (n) * 0x10)
+#define PINCTRL_IRQEN(n)	((cpu_is_mx23() ? 0x0900 : 0x1100) + (n) * 0x10)
+#define PINCTRL_IRQLEV(n)	((cpu_is_mx23() ? 0x0a00 : 0x1200) + (n) * 0x10)
+#define PINCTRL_IRQPOL(n)	((cpu_is_mx23() ? 0x0b00 : 0x1300) + (n) * 0x10)
+#define PINCTRL_IRQSTAT(n)	((cpu_is_mx23() ? 0x0c00 : 0x1400) + (n) * 0x10)
+
+#define GPIO_INT_FALL_EDGE	0x0
+#define GPIO_INT_LOW_LEV	0x1
+#define GPIO_INT_RISE_EDGE	0x2
+#define GPIO_INT_HIGH_LEV	0x3
+#define GPIO_INT_LEV_MASK	(1 << 0)
+#define GPIO_INT_POL_MASK	(1 << 1)
+
+/* Note: This driver assumes 32 GPIOs are handled in one register */
+
+static void clear_gpio_irqstatus(struct mxs_gpio_port *port, u32 index)
+{
+	__mxs_clrl(1 << index, port->base + PINCTRL_IRQSTAT(port->id));
+}
+
+static void set_gpio_irqenable(struct mxs_gpio_port *port, u32 index,
+				int enable)
+{
+	if (enable) {
+		__mxs_setl(1 << index, port->base + PINCTRL_IRQEN(port->id));
+		__mxs_setl(1 << index, port->base + PINCTRL_PIN2IRQ(port->id));
+	} else {
+		__mxs_clrl(1 << index, port->base + PINCTRL_IRQEN(port->id));
+	}
+}
+
+static void mxs_gpio_ack_irq(u32 irq)
+{
+	u32 gpio = irq_to_gpio(irq);
+	clear_gpio_irqstatus(&mxs_gpio_ports[gpio / 32], gpio & 0x1f);
+}
+
+static void mxs_gpio_mask_irq(u32 irq)
+{
+	u32 gpio = irq_to_gpio(irq);
+	set_gpio_irqenable(&mxs_gpio_ports[gpio / 32], gpio & 0x1f, 0);
+}
+
+static void mxs_gpio_unmask_irq(u32 irq)
+{
+	u32 gpio = irq_to_gpio(irq);
+	set_gpio_irqenable(&mxs_gpio_ports[gpio / 32], gpio & 0x1f, 1);
+}
+
+static int mxs_gpio_get(struct gpio_chip *chip, unsigned offset);
+
+static int mxs_gpio_set_irq_type(u32 irq, u32 type)
+{
+	u32 gpio = irq_to_gpio(irq);
+	u32 pin_mask = 1 << (gpio & 31);
+	struct mxs_gpio_port *port = &mxs_gpio_ports[gpio / 32];
+	void __iomem *pin_addr;
+	int edge;
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		edge = GPIO_INT_RISE_EDGE;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		edge = GPIO_INT_FALL_EDGE;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		edge = GPIO_INT_LOW_LEV;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		edge = GPIO_INT_HIGH_LEV;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* set level or edge */
+	pin_addr = port->base + PINCTRL_IRQLEV(port->id);
+	if (edge & GPIO_INT_LEV_MASK)
+		__mxs_setl(pin_mask, pin_addr);
+	else
+		__mxs_clrl(pin_mask, pin_addr);
+
+	/* set polarity */
+	pin_addr = port->base + PINCTRL_IRQPOL(port->id);
+	if (edge & GPIO_INT_POL_MASK)
+		__mxs_setl(pin_mask, pin_addr);
+	else
+		__mxs_clrl(pin_mask, pin_addr);
+
+	clear_gpio_irqstatus(port, gpio & 0x1f);
+
+	return 0;
+}
+
+/* MXS has one interrupt *per* gpio port */
+static void mxs_gpio_irq_handler(u32 irq, struct irq_desc *desc)
+{
+	u32 irq_stat;
+	struct mxs_gpio_port *port = (struct mxs_gpio_port *)get_irq_data(irq);
+	u32 gpio_irq_no_base = port->virtual_irq_start;
+
+	irq_stat = __raw_readl(port->base + PINCTRL_IRQSTAT(port->id)) &
+			__raw_readl(port->base + PINCTRL_IRQEN(port->id));
+
+	while (irq_stat != 0) {
+		int irqoffset = fls(irq_stat) - 1;
+		generic_handle_irq(gpio_irq_no_base + irqoffset);
+		irq_stat &= ~(1 << irqoffset);
+	}
+}
+
+/*
+ * Set interrupt number "irq" in the GPIO as a wake-up source.
+ * While system is running, all registered GPIO interrupts need to have
+ * wake-up enabled. When system is suspended, only selected GPIO interrupts
+ * need to have wake-up enabled.
+ * @param  irq          interrupt source number
+ * @param  enable       enable as wake-up if equal to non-zero
+ * @return       This function returns 0 on success.
+ */
+static int mxs_gpio_set_wake_irq(u32 irq, u32 enable)
+{
+	u32 gpio = irq_to_gpio(irq);
+	u32 gpio_idx = gpio & 0x1f;
+	struct mxs_gpio_port *port = &mxs_gpio_ports[gpio / 32];
+
+	if (enable) {
+		if (port->irq_high && (gpio_idx >= 16))
+			enable_irq_wake(port->irq_high);
+		else
+			enable_irq_wake(port->irq);
+	} else {
+		if (port->irq_high && (gpio_idx >= 16))
+			disable_irq_wake(port->irq_high);
+		else
+			disable_irq_wake(port->irq);
+	}
+
+	return 0;
+}
+
+static struct irq_chip gpio_irq_chip = {
+	.ack = mxs_gpio_ack_irq,
+	.mask = mxs_gpio_mask_irq,
+	.unmask = mxs_gpio_unmask_irq,
+	.set_type = mxs_gpio_set_irq_type,
+	.set_wake = mxs_gpio_set_wake_irq,
+};
+
+static void mxs_set_gpio_direction(struct gpio_chip *chip, unsigned offset,
+				int dir)
+{
+	struct mxs_gpio_port *port =
+		container_of(chip, struct mxs_gpio_port, chip);
+	void __iomem *pin_addr = port->base + PINCTRL_DOE(port->id);
+
+	if (dir)
+		__mxs_setl(1 << offset, pin_addr);
+	else
+		__mxs_clrl(1 << offset, pin_addr);
+}
+
+static int mxs_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct mxs_gpio_port *port =
+		container_of(chip, struct mxs_gpio_port, chip);
+
+	return (__raw_readl(port->base + PINCTRL_DIN(port->id)) >> offset) & 1;
+}
+
+static void mxs_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct mxs_gpio_port *port =
+		container_of(chip, struct mxs_gpio_port, chip);
+	void __iomem *pin_addr = port->base + PINCTRL_DOUT(port->id);
+
+	if (value)
+		__mxs_setl(1 << offset, pin_addr);
+	else
+		__mxs_clrl(1 << offset, pin_addr);
+}
+
+static int mxs_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	struct mxs_gpio_port *port =
+		container_of(chip, struct mxs_gpio_port, chip);
+
+	return port->virtual_irq_start + offset;
+}
+
+static int mxs_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	mxs_set_gpio_direction(chip, offset, 0);
+	return 0;
+}
+
+static int mxs_gpio_direction_output(struct gpio_chip *chip,
+				     unsigned offset, int value)
+{
+	mxs_gpio_set(chip, offset, value);
+	mxs_set_gpio_direction(chip, offset, 1);
+	return 0;
+}
+
+int __init mxs_gpio_init(struct mxs_gpio_port *port, int cnt)
+{
+	int i, j;
+
+	/* save for local usage */
+	mxs_gpio_ports = port;
+	gpio_table_size = cnt;
+
+	pr_info("MXS GPIO hardware\n");
+
+	for (i = 0; i < cnt; i++) {
+		/* disable the interrupt and clear the status */
+		__raw_writel(0, port[i].base + PINCTRL_PIN2IRQ(i));
+		__raw_writel(0, port[i].base + PINCTRL_IRQEN(i));
+
+		/* clear address has to be used to clear IRQSTAT bits */
+		__mxs_clrl(~0U, port[i].base + PINCTRL_IRQSTAT(i));
+
+		for (j = port[i].virtual_irq_start;
+			j < port[i].virtual_irq_start + 32; j++) {
+			set_irq_chip(j, &gpio_irq_chip);
+			set_irq_handler(j, handle_level_irq);
+			set_irq_flags(j, IRQF_VALID);
+		}
+
+		/* setup one handler for each entry */
+		set_irq_chained_handler(port[i].irq, mxs_gpio_irq_handler);
+		set_irq_data(port[i].irq, &port[i]);
+
+		/* register gpio chip */
+		port[i].chip.direction_input = mxs_gpio_direction_input;
+		port[i].chip.direction_output = mxs_gpio_direction_output;
+		port[i].chip.get = mxs_gpio_get;
+		port[i].chip.set = mxs_gpio_set;
+		port[i].chip.to_irq = mxs_gpio_to_irq;
+		port[i].chip.base = i * 32;
+		port[i].chip.ngpio = 32;
+
+		/* its a serious configuration bug when it fails */
+		BUG_ON(gpiochip_add(&port[i].chip) < 0);
+	}
+
+	return 0;
+}
+
+#define DEFINE_MXS_GPIO_PORT(soc, _id)					\
+	{								\
+		.chip.label = "gpio-" #_id,				\
+		.id = _id,						\
+		.irq = soc ## _INT_GPIO ## _id,				\
+		.base = soc ## _IO_ADDRESS(				\
+				soc ## _PINCTRL ## _BASE_ADDR),		\
+		.virtual_irq_start = MXS_GPIO_IRQ_START + (_id) * 32,	\
+	}
+
+#define DEFINE_REGISTER_FUNCTION(prefix)				\
+int __init prefix ## _register_gpios(void)				\
+{									\
+	return mxs_gpio_init(prefix ## _gpio_ports,			\
+			ARRAY_SIZE(prefix ## _gpio_ports));		\
+}
+
+#ifdef CONFIG_SOC_IMX23
+static struct mxs_gpio_port mx23_gpio_ports[] = {
+	DEFINE_MXS_GPIO_PORT(MX23, 0),
+	DEFINE_MXS_GPIO_PORT(MX23, 1),
+	DEFINE_MXS_GPIO_PORT(MX23, 2),
+};
+DEFINE_REGISTER_FUNCTION(mx23)
+#endif
+
+#ifdef CONFIG_SOC_IMX28
+static struct mxs_gpio_port mx28_gpio_ports[] = {
+	DEFINE_MXS_GPIO_PORT(MX28, 0),
+	DEFINE_MXS_GPIO_PORT(MX28, 1),
+	DEFINE_MXS_GPIO_PORT(MX28, 2),
+	DEFINE_MXS_GPIO_PORT(MX28, 3),
+	DEFINE_MXS_GPIO_PORT(MX28, 4),
+};
+DEFINE_REGISTER_FUNCTION(mx28)
+#endif
diff --git a/arch/arm/mach-mxs/gpio.h b/arch/arm/mach-mxs/gpio.h
new file mode 100644
index 0000000..005bb06
--- /dev/null
+++ b/arch/arm/mach-mxs/gpio.h
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2008 Juergen Beisert, kernel at pengutronix.de
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA  02110-1301, USA.
+ */
+
+#ifndef __MXS_GPIO_H__
+#define __MXS_GPIO_H__
+
+struct mxs_gpio_port {
+	void __iomem *base;
+	int id;
+	int irq;
+	int irq_high;
+	int virtual_irq_start;
+	struct gpio_chip chip;
+};
+
+int mxs_gpio_init(struct mxs_gpio_port*, int);
+
+#endif /* __MXS_GPIO_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/gpio.h b/arch/arm/mach-mxs/include/mach/gpio.h
new file mode 100644
index 0000000..828cccc
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/gpio.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2008 Juergen Beisert, kernel@pengutronix.de
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA  02110-1301, USA.
+ */
+
+#ifndef __MACH_MXS_GPIO_H__
+#define __MACH_MXS_GPIO_H__
+
+#include <asm-generic/gpio.h>
+
+#define MXS_GPIO_NR(bank, nr)	((bank) * 32 + (nr))
+
+/* use gpiolib dispatchers */
+#define gpio_get_value		__gpio_get_value
+#define gpio_set_value		__gpio_set_value
+#define gpio_cansleep		__gpio_cansleep
+#define gpio_to_irq		__gpio_to_irq
+
+#define irq_to_gpio(irq)	((irq) - MXS_GPIO_IRQ_START)
+
+#endif /* __MACH_MXS_GPIO_H__ */
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v7 08/15] ARM: mxs: Add iomux support
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
                   ` (4 preceding siblings ...)
  2010-12-18 13:39 ` [PATCH v7 07/15] ARM: mxs: Add gpio support Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  2010-12-20  9:44   ` Uwe Kleine-König
  2010-12-18 13:39 ` [PATCH v7 09/15] ARM: mxs: Add clock support Shawn Guo
                   ` (2 subsequent siblings)
  8 siblings, 1 reply; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

MXS-based SoCs implements iomux functions in block PINCTRL.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Changes for v7
 - Define naked pad and introduce validity bits for mA/vol/pull
   to ease the pad modification
 - List all pad definitions at once generated from Freescale
   pinmux Excel sheet

Changes for v6:
 - Use __mxs_setl() and __mxs_clrl() for bit set/clear

Changes for v5:
 - Change iomux_cfg_t from u64 to u16
 - Add namespace MXS_ to shift, mask, and pad definitions
 - Use SET/CLR register for 1 bit setting
 - Get "if" and "{" at the same line
 - Remove space in middle of tabs
 - Change "setups" to "configures" in comments

Changes for v3:
 - Change iomux_cfg_t to u64 to facilitate adding platform specific
   pad_ctrl settings to an existing pad definition
 - Change inclusion of hardware.h to mxs.h
 - Get iomux_base a hard-assignment in mxs_iomux_setup_pad(), since
   mx23 and mx28 share the common pinctrl base adress and it's only
   used in mxs_iomux_setup_pad().
 - Remove EXPORT_SYMBOL and the static of mxs_iomux_setup_pad()

Changes for v2:
 - Define iomux_cfg_t as u64
 - Turn mxs_iomux_setup_pad() into a static function
 - Fix a bug in mxs_iomux_setup_pad(), muxsel starts at offset 0x100 than 0 of pinctrl block.

 arch/arm/mach-mxs/include/mach/iomux-mx23.h |  355 ++++++++++++++++++
 arch/arm/mach-mxs/include/mach/iomux-mx28.h |  537 +++++++++++++++++++++++++++
 arch/arm/mach-mxs/include/mach/iomux.h      |  165 ++++++++
 arch/arm/mach-mxs/iomux.c                   |  101 +++++
 4 files changed, 1158 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/include/mach/iomux-mx23.h
 create mode 100644 arch/arm/mach-mxs/include/mach/iomux-mx28.h
 create mode 100644 arch/arm/mach-mxs/include/mach/iomux.h
 create mode 100644 arch/arm/mach-mxs/iomux.c

diff --git a/arch/arm/mach-mxs/include/mach/iomux-mx23.h b/arch/arm/mach-mxs/include/mach/iomux-mx23.h
new file mode 100644
index 0000000..94e5dd8
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/iomux-mx23.h
@@ -0,0 +1,355 @@
+/*
+ * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __MACH_IOMUX_MX23_H__
+#define __MACH_IOMUX_MX23_H__
+
+#include <mach/iomux.h>
+
+/*
+ * The naming convention for the pad modes is MX23_PAD_<padname>__<padmode>
+ * If <padname> or <padmode> refers to a GPIO, it is named GPIO_<unit>_<num>
+ * See also iomux.h
+ *
+ *									BANK	PIN	MUX
+ */
+/* MUXSEL_0 */
+#define MX23_PAD_GPMI_D00__GPMI_D00		MXS_IOMUX_PAD_NAKED(0,  0, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D01__GPMI_D01		MXS_IOMUX_PAD_NAKED(0,  1, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D02__GPMI_D02		MXS_IOMUX_PAD_NAKED(0,  2, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D03__GPMI_D03		MXS_IOMUX_PAD_NAKED(0,  3, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D04__GPMI_D04		MXS_IOMUX_PAD_NAKED(0,  4, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D05__GPMI_D05		MXS_IOMUX_PAD_NAKED(0,  5, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D06__GPMI_D06		MXS_IOMUX_PAD_NAKED(0,  6, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D07__GPMI_D07		MXS_IOMUX_PAD_NAKED(0,  7, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D08__GPMI_D08		MXS_IOMUX_PAD_NAKED(0,  8, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D09__GPMI_D09		MXS_IOMUX_PAD_NAKED(0,  9, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D10__GPMI_D10		MXS_IOMUX_PAD_NAKED(0, 10, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D11__GPMI_D11		MXS_IOMUX_PAD_NAKED(0, 11, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D12__GPMI_D12		MXS_IOMUX_PAD_NAKED(0, 12, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D13__GPMI_D13		MXS_IOMUX_PAD_NAKED(0, 13, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D14__GPMI_D14		MXS_IOMUX_PAD_NAKED(0, 14, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_D15__GPMI_D15		MXS_IOMUX_PAD_NAKED(0, 15, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_CLE__GPMI_CLE		MXS_IOMUX_PAD_NAKED(0, 16, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_ALE__GPMI_ALE		MXS_IOMUX_PAD_NAKED(0, 17, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_CE2N__GPMI_CE2N		MXS_IOMUX_PAD_NAKED(0, 18, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_RDY0__GPMI_RDY0		MXS_IOMUX_PAD_NAKED(0, 19, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_RDY1__GPMI_RDY1		MXS_IOMUX_PAD_NAKED(0, 20, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_RDY2__GPMI_RDY2		MXS_IOMUX_PAD_NAKED(0, 21, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_RDY3__GPMI_RDY3		MXS_IOMUX_PAD_NAKED(0, 22, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_WPN__GPMI_WPN		MXS_IOMUX_PAD_NAKED(0, 23, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_WRN__GPMI_WRN		MXS_IOMUX_PAD_NAKED(0, 24, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_RDN__GPMI_RDN		MXS_IOMUX_PAD_NAKED(0, 25, PAD_MUXSEL_0)
+#define MX23_PAD_AUART1_CTS__AUART1_CTS		MXS_IOMUX_PAD_NAKED(0, 26, PAD_MUXSEL_0)
+#define MX23_PAD_AUART1_RTS__AUART1_RTS		MXS_IOMUX_PAD_NAKED(0, 27, PAD_MUXSEL_0)
+#define MX23_PAD_AUART1_RX__AUART1_RX		MXS_IOMUX_PAD_NAKED(0, 28, PAD_MUXSEL_0)
+#define MX23_PAD_AUART1_TX__AUART1_TX		MXS_IOMUX_PAD_NAKED(0, 29, PAD_MUXSEL_0)
+#define MX23_PAD_I2C_SCL__I2C_SCL		MXS_IOMUX_PAD_NAKED(0, 30, PAD_MUXSEL_0)
+#define MX23_PAD_I2C_SDA__I2C_SDA		MXS_IOMUX_PAD_NAKED(0, 31, PAD_MUXSEL_0)
+
+#define MX23_PAD_LCD_D00__LCD_D00		MXS_IOMUX_PAD_NAKED(1,  0, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D01__LCD_D01		MXS_IOMUX_PAD_NAKED(1,  1, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D02__LCD_D02		MXS_IOMUX_PAD_NAKED(1,  2, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D03__LCD_D03		MXS_IOMUX_PAD_NAKED(1,  3, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D04__LCD_D04		MXS_IOMUX_PAD_NAKED(1,  4, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D05__LCD_D05		MXS_IOMUX_PAD_NAKED(1,  5, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D06__LCD_D06		MXS_IOMUX_PAD_NAKED(1,  6, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D07__LCD_D07		MXS_IOMUX_PAD_NAKED(1,  7, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D08__LCD_D08		MXS_IOMUX_PAD_NAKED(1,  8, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D09__LCD_D09		MXS_IOMUX_PAD_NAKED(1,  9, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D10__LCD_D10		MXS_IOMUX_PAD_NAKED(1, 10, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D11__LCD_D11		MXS_IOMUX_PAD_NAKED(1, 11, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D12__LCD_D12		MXS_IOMUX_PAD_NAKED(1, 12, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D13__LCD_D13		MXS_IOMUX_PAD_NAKED(1, 13, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D14__LCD_D14		MXS_IOMUX_PAD_NAKED(1, 14, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D15__LCD_D15		MXS_IOMUX_PAD_NAKED(1, 15, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D16__LCD_D16		MXS_IOMUX_PAD_NAKED(1, 16, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_D17__LCD_D17		MXS_IOMUX_PAD_NAKED(1, 17, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_RESET__LCD_RESET		MXS_IOMUX_PAD_NAKED(1, 18, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_RS__LCD_RS			MXS_IOMUX_PAD_NAKED(1, 19, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_WR__LCD_WR			MXS_IOMUX_PAD_NAKED(1, 20, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_CS__LCD_CS			MXS_IOMUX_PAD_NAKED(1, 21, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_DOTCK__LCD_DOTCK		MXS_IOMUX_PAD_NAKED(1, 22, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_ENABLE__LCD_ENABLE		MXS_IOMUX_PAD_NAKED(1, 23, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_HSYNC__LCD_HSYNC		MXS_IOMUX_PAD_NAKED(1, 24, PAD_MUXSEL_0)
+#define MX23_PAD_LCD_VSYNC__LCD_VSYNC		MXS_IOMUX_PAD_NAKED(1, 25, PAD_MUXSEL_0)
+#define MX23_PAD_PWM0__PWM0			MXS_IOMUX_PAD_NAKED(1, 26, PAD_MUXSEL_0)
+#define MX23_PAD_PWM1__PWM1			MXS_IOMUX_PAD_NAKED(1, 27, PAD_MUXSEL_0)
+#define MX23_PAD_PWM2__PWM2			MXS_IOMUX_PAD_NAKED(1, 28, PAD_MUXSEL_0)
+#define MX23_PAD_PWM3__PWM3			MXS_IOMUX_PAD_NAKED(1, 29, PAD_MUXSEL_0)
+#define MX23_PAD_PWM4__PWM4			MXS_IOMUX_PAD_NAKED(1, 30, PAD_MUXSEL_0)
+
+#define MX23_PAD_SSP1_CMD__SSP1_CMD		MXS_IOMUX_PAD_NAKED(2,  0, PAD_MUXSEL_0)
+#define MX23_PAD_SSP1_DETECT__SSP1_DETECT	MXS_IOMUX_PAD_NAKED(2,  1, PAD_MUXSEL_0)
+#define MX23_PAD_SSP1_DATA0__SSP1_DATA0		MXS_IOMUX_PAD_NAKED(2,  2, PAD_MUXSEL_0)
+#define MX23_PAD_SSP1_DATA1__SSP1_DATA1		MXS_IOMUX_PAD_NAKED(2,  3, PAD_MUXSEL_0)
+#define MX23_PAD_SSP1_DATA2__SSP1_DATA2		MXS_IOMUX_PAD_NAKED(2,  4, PAD_MUXSEL_0)
+#define MX23_PAD_SSP1_DATA3__SSP1_DATA3		MXS_IOMUX_PAD_NAKED(2,  5, PAD_MUXSEL_0)
+#define MX23_PAD_SSP1_SCK__SSP1_SCK		MXS_IOMUX_PAD_NAKED(2,  6, PAD_MUXSEL_0)
+#define MX23_PAD_ROTARYA__ROTARYA		MXS_IOMUX_PAD_NAKED(2,  7, PAD_MUXSEL_0)
+#define MX23_PAD_ROTARYB__ROTARYB		MXS_IOMUX_PAD_NAKED(2,  8, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A00__EMI_A00		MXS_IOMUX_PAD_NAKED(2,  9, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A01__EMI_A01		MXS_IOMUX_PAD_NAKED(2, 10, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A02__EMI_A02		MXS_IOMUX_PAD_NAKED(2, 11, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A03__EMI_A03		MXS_IOMUX_PAD_NAKED(2, 12, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A04__EMI_A04		MXS_IOMUX_PAD_NAKED(2, 13, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A05__EMI_A05		MXS_IOMUX_PAD_NAKED(2, 14, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A06__EMI_A06		MXS_IOMUX_PAD_NAKED(2, 15, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A07__EMI_A07		MXS_IOMUX_PAD_NAKED(2, 16, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A08__EMI_A08		MXS_IOMUX_PAD_NAKED(2, 17, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A09__EMI_A09		MXS_IOMUX_PAD_NAKED(2, 18, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A10__EMI_A10		MXS_IOMUX_PAD_NAKED(2, 19, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A11__EMI_A11		MXS_IOMUX_PAD_NAKED(2, 20, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_A12__EMI_A12		MXS_IOMUX_PAD_NAKED(2, 21, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_BA0__EMI_BA0		MXS_IOMUX_PAD_NAKED(2, 22, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_BA1__EMI_BA1		MXS_IOMUX_PAD_NAKED(2, 23, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_CASN__EMI_CASN		MXS_IOMUX_PAD_NAKED(2, 24, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_CE0N__EMI_CE0N		MXS_IOMUX_PAD_NAKED(2, 25, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_CE1N__EMI_CE1N		MXS_IOMUX_PAD_NAKED(2, 26, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_CE1N__GPMI_CE1N		MXS_IOMUX_PAD_NAKED(2, 27, PAD_MUXSEL_0)
+#define MX23_PAD_GPMI_CE0N__GPMI_CE0N		MXS_IOMUX_PAD_NAKED(2, 28, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_CKE__EMI_CKE		MXS_IOMUX_PAD_NAKED(2, 29, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_RASN__EMI_RASN		MXS_IOMUX_PAD_NAKED(2, 30, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_WEN__EMI_WEN		MXS_IOMUX_PAD_NAKED(2, 31, PAD_MUXSEL_0)
+
+#define MX23_PAD_EMI_D00__EMI_D00		MXS_IOMUX_PAD_NAKED(3,  0, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D01__EMI_D01		MXS_IOMUX_PAD_NAKED(3,  1, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D02__EMI_D02		MXS_IOMUX_PAD_NAKED(3,  2, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D03__EMI_D03		MXS_IOMUX_PAD_NAKED(3,  3, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D04__EMI_D04		MXS_IOMUX_PAD_NAKED(3,  4, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D05__EMI_D05		MXS_IOMUX_PAD_NAKED(3,  5, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D06__EMI_D06		MXS_IOMUX_PAD_NAKED(3,  6, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D07__EMI_D07		MXS_IOMUX_PAD_NAKED(3,  7, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D08__EMI_D08		MXS_IOMUX_PAD_NAKED(3,  8, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D09__EMI_D09		MXS_IOMUX_PAD_NAKED(3,  9, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D10__EMI_D10		MXS_IOMUX_PAD_NAKED(3, 10, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D11__EMI_D11		MXS_IOMUX_PAD_NAKED(3, 11, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D12__EMI_D12		MXS_IOMUX_PAD_NAKED(3, 12, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D13__EMI_D13		MXS_IOMUX_PAD_NAKED(3, 13, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D14__EMI_D14		MXS_IOMUX_PAD_NAKED(3, 14, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_D15__EMI_D15		MXS_IOMUX_PAD_NAKED(3, 15, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_DQM0__EMI_DQM0		MXS_IOMUX_PAD_NAKED(3, 16, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_DQM1__EMI_DQM1		MXS_IOMUX_PAD_NAKED(3, 17, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_DQS0__EMI_DQS0		MXS_IOMUX_PAD_NAKED(3, 18, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_DQS1__EMI_DQS1		MXS_IOMUX_PAD_NAKED(3, 19, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_CLK__EMI_CLK		MXS_IOMUX_PAD_NAKED(3, 20, PAD_MUXSEL_0)
+#define MX23_PAD_EMI_CLKN__EMI_CLKN		MXS_IOMUX_PAD_NAKED(3, 21, PAD_MUXSEL_0)
+
+/* MUXSEL_1 */
+#define MX23_PAD_GPMI_D00__LCD_D8		MXS_IOMUX_PAD_NAKED(0,  0, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D01__LCD_D9		MXS_IOMUX_PAD_NAKED(0,  1, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D02__LCD_D10		MXS_IOMUX_PAD_NAKED(0,  2, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D03__LCD_D11		MXS_IOMUX_PAD_NAKED(0,  3, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D04__LCD_D12		MXS_IOMUX_PAD_NAKED(0,  4, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D05__LCD_D13		MXS_IOMUX_PAD_NAKED(0,  5, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D06__LCD_D14		MXS_IOMUX_PAD_NAKED(0,  6, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D07__LCD_D15		MXS_IOMUX_PAD_NAKED(0,  7, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D08__LCD_D18		MXS_IOMUX_PAD_NAKED(0,  8, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D09__LCD_D19		MXS_IOMUX_PAD_NAKED(0,  9, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D10__LCD_D20		MXS_IOMUX_PAD_NAKED(0, 10, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D11__LCD_D21		MXS_IOMUX_PAD_NAKED(0, 11, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D12__LCD_D22		MXS_IOMUX_PAD_NAKED(0, 12, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D13__LCD_D23		MXS_IOMUX_PAD_NAKED(0, 13, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D14__AUART2_RX		MXS_IOMUX_PAD_NAKED(0, 14, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_D15__AUART2_TX		MXS_IOMUX_PAD_NAKED(0, 15, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_CLE__LCD_D16		MXS_IOMUX_PAD_NAKED(0, 16, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_ALE__LCD_D17		MXS_IOMUX_PAD_NAKED(0, 17, PAD_MUXSEL_1)
+#define MX23_PAD_GPMI_CE2N__ATA_A2		MXS_IOMUX_PAD_NAKED(0, 18, PAD_MUXSEL_1)
+#define MX23_PAD_AUART1_RTS__IR_CLK		MXS_IOMUX_PAD_NAKED(0, 27, PAD_MUXSEL_1)
+#define MX23_PAD_AUART1_RX__IR_RX		MXS_IOMUX_PAD_NAKED(0, 28, PAD_MUXSEL_1)
+#define MX23_PAD_AUART1_TX__IR_TX		MXS_IOMUX_PAD_NAKED(0, 29, PAD_MUXSEL_1)
+#define MX23_PAD_I2C_SCL__GPMI_RDY2		MXS_IOMUX_PAD_NAKED(0, 30, PAD_MUXSEL_1)
+#define MX23_PAD_I2C_SDA__GPMI_CE2N		MXS_IOMUX_PAD_NAKED(0, 31, PAD_MUXSEL_1)
+
+#define MX23_PAD_LCD_D00__ETM_DA8		MXS_IOMUX_PAD_NAKED(1,  0, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D01__ETM_DA9		MXS_IOMUX_PAD_NAKED(1,  1, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D02__ETM_DA10		MXS_IOMUX_PAD_NAKED(1,  2, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D03__ETM_DA11		MXS_IOMUX_PAD_NAKED(1,  3, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D04__ETM_DA12		MXS_IOMUX_PAD_NAKED(1,  4, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D05__ETM_DA13		MXS_IOMUX_PAD_NAKED(1,  5, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D06__ETM_DA14		MXS_IOMUX_PAD_NAKED(1,  6, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D07__ETM_DA15		MXS_IOMUX_PAD_NAKED(1,  7, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D08__ETM_DA0		MXS_IOMUX_PAD_NAKED(1,  8, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D09__ETM_DA1		MXS_IOMUX_PAD_NAKED(1,  9, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D10__ETM_DA2		MXS_IOMUX_PAD_NAKED(1, 10, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D11__ETM_DA3		MXS_IOMUX_PAD_NAKED(1, 11, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D12__ETM_DA4		MXS_IOMUX_PAD_NAKED(1, 12, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D13__ETM_DA5		MXS_IOMUX_PAD_NAKED(1, 13, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D14__ETM_DA6		MXS_IOMUX_PAD_NAKED(1, 14, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_D15__ETM_DA7		MXS_IOMUX_PAD_NAKED(1, 15, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_RESET__ETM_TCTL		MXS_IOMUX_PAD_NAKED(1, 18, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_RS__ETM_TCLK		MXS_IOMUX_PAD_NAKED(1, 19, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_DOTCK__GPMI_RDY3		MXS_IOMUX_PAD_NAKED(1, 22, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_ENABLE__I2C_SCL		MXS_IOMUX_PAD_NAKED(1, 23, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_HSYNC__I2C_SDA		MXS_IOMUX_PAD_NAKED(1, 24, PAD_MUXSEL_1)
+#define MX23_PAD_LCD_VSYNC__LCD_BUSY		MXS_IOMUX_PAD_NAKED(1, 25, PAD_MUXSEL_1)
+#define MX23_PAD_PWM0__ROTARYA			MXS_IOMUX_PAD_NAKED(1, 26, PAD_MUXSEL_1)
+#define MX23_PAD_PWM1__ROTARYB			MXS_IOMUX_PAD_NAKED(1, 27, PAD_MUXSEL_1)
+#define MX23_PAD_PWM2__GPMI_RDY3		MXS_IOMUX_PAD_NAKED(1, 28, PAD_MUXSEL_1)
+#define MX23_PAD_PWM3__ETM_TCTL			MXS_IOMUX_PAD_NAKED(1, 29, PAD_MUXSEL_1)
+#define MX23_PAD_PWM4__ETM_TCLK			MXS_IOMUX_PAD_NAKED(1, 30, PAD_MUXSEL_1)
+
+#define MX23_PAD_SSP1_DETECT__GPMI_CE3N		MXS_IOMUX_PAD_NAKED(2,  1, PAD_MUXSEL_1)
+#define MX23_PAD_SSP1_DATA1__I2C_SCL		MXS_IOMUX_PAD_NAKED(2,  3, PAD_MUXSEL_1)
+#define MX23_PAD_SSP1_DATA2__I2C_SDA		MXS_IOMUX_PAD_NAKED(2,  4, PAD_MUXSEL_1)
+#define MX23_PAD_ROTARYA__AUART2_RTS		MXS_IOMUX_PAD_NAKED(2,  7, PAD_MUXSEL_1)
+#define MX23_PAD_ROTARYB__AUART2_CTS		MXS_IOMUX_PAD_NAKED(2,  8, PAD_MUXSEL_1)
+
+/* MUXSEL_2 */
+#define MX23_PAD_GPMI_D00__SSP2_DATA0		MXS_IOMUX_PAD_NAKED(0,  0, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D01__SSP2_DATA1		MXS_IOMUX_PAD_NAKED(0,  1, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D02__SSP2_DATA2		MXS_IOMUX_PAD_NAKED(0,  2, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D03__SSP2_DATA3		MXS_IOMUX_PAD_NAKED(0,  3, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D04__SSP2_DATA4		MXS_IOMUX_PAD_NAKED(0,  4, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D05__SSP2_DATA5		MXS_IOMUX_PAD_NAKED(0,  5, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D06__SSP2_DATA6		MXS_IOMUX_PAD_NAKED(0,  6, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D07__SSP2_DATA7		MXS_IOMUX_PAD_NAKED(0,  7, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D08__SSP1_DATA4		MXS_IOMUX_PAD_NAKED(0,  8, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D09__SSP1_DATA5		MXS_IOMUX_PAD_NAKED(0,  9, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D10__SSP1_DATA6		MXS_IOMUX_PAD_NAKED(0, 10, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D11__SSP1_DATA7		MXS_IOMUX_PAD_NAKED(0, 11, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_D15__GPMI_CE3N		MXS_IOMUX_PAD_NAKED(0, 15, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_RDY0__SSP2_DETECT		MXS_IOMUX_PAD_NAKED(0, 19, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_RDY1__SSP2_CMD		MXS_IOMUX_PAD_NAKED(0, 20, PAD_MUXSEL_2)
+#define MX23_PAD_GPMI_WRN__SSP2_SCK		MXS_IOMUX_PAD_NAKED(0, 24, PAD_MUXSEL_2)
+#define MX23_PAD_AUART1_CTS__SSP1_DATA4		MXS_IOMUX_PAD_NAKED(0, 26, PAD_MUXSEL_2)
+#define MX23_PAD_AUART1_RTS__SSP1_DATA5		MXS_IOMUX_PAD_NAKED(0, 27, PAD_MUXSEL_2)
+#define MX23_PAD_AUART1_RX__SSP1_DATA6		MXS_IOMUX_PAD_NAKED(0, 28, PAD_MUXSEL_2)
+#define MX23_PAD_AUART1_TX__SSP1_DATA7		MXS_IOMUX_PAD_NAKED(0, 29, PAD_MUXSEL_2)
+#define MX23_PAD_I2C_SCL__AUART1_TX		MXS_IOMUX_PAD_NAKED(0, 30, PAD_MUXSEL_2)
+#define MX23_PAD_I2C_SDA__AUART1_RX		MXS_IOMUX_PAD_NAKED(0, 31, PAD_MUXSEL_2)
+
+#define MX23_PAD_LCD_D08__SAIF2_SDATA0		MXS_IOMUX_PAD_NAKED(1,  8, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_D09__SAIF1_SDATA0		MXS_IOMUX_PAD_NAKED(1,  9, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_D10__SAIF_MCLK_BITCLK	MXS_IOMUX_PAD_NAKED(1, 10, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_D11__SAIF_LRCLK		MXS_IOMUX_PAD_NAKED(1, 11, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_D12__SAIF2_SDATA1		MXS_IOMUX_PAD_NAKED(1, 12, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_D13__SAIF2_SDATA2		MXS_IOMUX_PAD_NAKED(1, 13, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_D14__SAIF1_SDATA2		MXS_IOMUX_PAD_NAKED(1, 14, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_D15__SAIF1_SDATA1		MXS_IOMUX_PAD_NAKED(1, 15, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_D16__SAIF_ALT_BITCLK	MXS_IOMUX_PAD_NAKED(1, 16, PAD_MUXSEL_2)
+#define MX23_PAD_LCD_RESET__GPMI_CE3N		MXS_IOMUX_PAD_NAKED(1, 18, PAD_MUXSEL_2)
+#define MX23_PAD_PWM0__DUART_RX			MXS_IOMUX_PAD_NAKED(1, 26, PAD_MUXSEL_2)
+#define MX23_PAD_PWM1__DUART_TX			MXS_IOMUX_PAD_NAKED(1, 27, PAD_MUXSEL_2)
+#define MX23_PAD_PWM3__AUART1_CTS		MXS_IOMUX_PAD_NAKED(1, 29, PAD_MUXSEL_2)
+#define MX23_PAD_PWM4__AUART1_RTS		MXS_IOMUX_PAD_NAKED(1, 30, PAD_MUXSEL_2)
+
+#define MX23_PAD_SSP1_CMD__JTAG_TDO		MXS_IOMUX_PAD_NAKED(2,  0, PAD_MUXSEL_2)
+#define MX23_PAD_SSP1_DETECT__USB_OTG_ID	MXS_IOMUX_PAD_NAKED(2,  1, PAD_MUXSEL_2)
+#define MX23_PAD_SSP1_DATA0__JTAG_TDI		MXS_IOMUX_PAD_NAKED(2,  2, PAD_MUXSEL_2)
+#define MX23_PAD_SSP1_DATA1__JTAG_TCLK		MXS_IOMUX_PAD_NAKED(2,  3, PAD_MUXSEL_2)
+#define MX23_PAD_SSP1_DATA2__JTAG_RTCK		MXS_IOMUX_PAD_NAKED(2,  4, PAD_MUXSEL_2)
+#define MX23_PAD_SSP1_DATA3__JTAG_TMS		MXS_IOMUX_PAD_NAKED(2,  5, PAD_MUXSEL_2)
+#define MX23_PAD_SSP1_SCK__JTAG_TRST		MXS_IOMUX_PAD_NAKED(2,  6, PAD_MUXSEL_2)
+#define MX23_PAD_ROTARYA__SPDIF			MXS_IOMUX_PAD_NAKED(2,  7, PAD_MUXSEL_2)
+#define MX23_PAD_ROTARYB__GPMI_CE3N		MXS_IOMUX_PAD_NAKED(2,  8, PAD_MUXSEL_2)
+
+/* MUXSEL_GPIO */
+#define MX23_PAD_GPMI_D00__GPO_0_0		MXS_IOMUX_PAD_NAKED(0,  0, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D01__GPO_0_1		MXS_IOMUX_PAD_NAKED(0,  1, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D02__GPO_0_2		MXS_IOMUX_PAD_NAKED(0,  2, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D03__GPO_0_3		MXS_IOMUX_PAD_NAKED(0,  3, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D04__GPO_0_4		MXS_IOMUX_PAD_NAKED(0,  4, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D05__GPO_0_5		MXS_IOMUX_PAD_NAKED(0,  5, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D06__GPO_0_6		MXS_IOMUX_PAD_NAKED(0,  6, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D07__GPO_0_7		MXS_IOMUX_PAD_NAKED(0,  7, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D08__GPO_0_8		MXS_IOMUX_PAD_NAKED(0,  8, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D09__GPO_0_9		MXS_IOMUX_PAD_NAKED(0,  9, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D10__GPO_0_10		MXS_IOMUX_PAD_NAKED(0, 10, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D11__GPO_0_11		MXS_IOMUX_PAD_NAKED(0, 11, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D12__GPO_0_12		MXS_IOMUX_PAD_NAKED(0, 12, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D13__GPO_0_13		MXS_IOMUX_PAD_NAKED(0, 13, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D14__GPO_0_14		MXS_IOMUX_PAD_NAKED(0, 14, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_D15__GPO_0_15		MXS_IOMUX_PAD_NAKED(0, 15, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_CLE__GPO_0_16		MXS_IOMUX_PAD_NAKED(0, 16, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_ALE__GPO_0_17		MXS_IOMUX_PAD_NAKED(0, 17, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_CE2N__GPO_0_18		MXS_IOMUX_PAD_NAKED(0, 18, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_RDY0__GPO_0_19		MXS_IOMUX_PAD_NAKED(0, 19, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_RDY1__GPO_0_20		MXS_IOMUX_PAD_NAKED(0, 20, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_RDY2__GPO_0_21		MXS_IOMUX_PAD_NAKED(0, 21, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_RDY3__GPO_0_22		MXS_IOMUX_PAD_NAKED(0, 22, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_WPN__GPO_0_23		MXS_IOMUX_PAD_NAKED(0, 23, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_WRN__GPO_0_24		MXS_IOMUX_PAD_NAKED(0, 24, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_RDN__GPO_0_25		MXS_IOMUX_PAD_NAKED(0, 25, PAD_MUXSEL_GPIO)
+#define MX23_PAD_AUART1_CTS__GPO_0_26		MXS_IOMUX_PAD_NAKED(0, 26, PAD_MUXSEL_GPIO)
+#define MX23_PAD_AUART1_RTS__GPO_0_27		MXS_IOMUX_PAD_NAKED(0, 27, PAD_MUXSEL_GPIO)
+#define MX23_PAD_AUART1_RX__GPO_0_28		MXS_IOMUX_PAD_NAKED(0, 28, PAD_MUXSEL_GPIO)
+#define MX23_PAD_AUART1_TX__GPO_0_29		MXS_IOMUX_PAD_NAKED(0, 29, PAD_MUXSEL_GPIO)
+#define MX23_PAD_I2C_SCL__GPO_0_30		MXS_IOMUX_PAD_NAKED(0, 30, PAD_MUXSEL_GPIO)
+#define MX23_PAD_I2C_SDA__GPO_0_31		MXS_IOMUX_PAD_NAKED(0, 31, PAD_MUXSEL_GPIO)
+
+#define MX23_PAD_LCD_D00__GPO_1_0		MXS_IOMUX_PAD_NAKED(1,  0, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D01__GPO_1_1		MXS_IOMUX_PAD_NAKED(1,  1, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D02__GPO_1_2		MXS_IOMUX_PAD_NAKED(1,  2, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D03__GPO_1_3		MXS_IOMUX_PAD_NAKED(1,  3, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D04__GPO_1_4		MXS_IOMUX_PAD_NAKED(1,  4, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D05__GPO_1_5		MXS_IOMUX_PAD_NAKED(1,  5, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D06__GPO_1_6		MXS_IOMUX_PAD_NAKED(1,  6, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D07__GPO_1_7		MXS_IOMUX_PAD_NAKED(1,  7, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D08__GPO_1_8		MXS_IOMUX_PAD_NAKED(1,  8, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D09__GPO_1_9		MXS_IOMUX_PAD_NAKED(1,  9, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D10__GPO_1_10		MXS_IOMUX_PAD_NAKED(1, 10, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D11__GPO_1_11		MXS_IOMUX_PAD_NAKED(1, 11, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D12__GPO_1_12		MXS_IOMUX_PAD_NAKED(1, 12, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D13__GPO_1_13		MXS_IOMUX_PAD_NAKED(1, 13, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D14__GPO_1_14		MXS_IOMUX_PAD_NAKED(1, 14, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D15__GPO_1_15		MXS_IOMUX_PAD_NAKED(1, 15, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D16__GPO_1_16		MXS_IOMUX_PAD_NAKED(1, 16, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_D17__GPO_1_17		MXS_IOMUX_PAD_NAKED(1, 17, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_RESET__GPO_1_18		MXS_IOMUX_PAD_NAKED(1, 18, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_RS__GPO_1_19		MXS_IOMUX_PAD_NAKED(1, 19, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_WR__GPO_1_20		MXS_IOMUX_PAD_NAKED(1, 20, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_CS__GPO_1_21		MXS_IOMUX_PAD_NAKED(1, 21, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_DOTCK__GPO_1_22		MXS_IOMUX_PAD_NAKED(1, 22, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_ENABLE__GPO_1_23		MXS_IOMUX_PAD_NAKED(1, 23, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_HSYNC__GPO_1_24		MXS_IOMUX_PAD_NAKED(1, 24, PAD_MUXSEL_GPIO)
+#define MX23_PAD_LCD_VSYNC__GPO_1_25		MXS_IOMUX_PAD_NAKED(1, 25, PAD_MUXSEL_GPIO)
+#define MX23_PAD_PWM0__GPO_1_26			MXS_IOMUX_PAD_NAKED(1, 26, PAD_MUXSEL_GPIO)
+#define MX23_PAD_PWM1__GPO_1_27			MXS_IOMUX_PAD_NAKED(1, 27, PAD_MUXSEL_GPIO)
+#define MX23_PAD_PWM2__GPO_1_28			MXS_IOMUX_PAD_NAKED(1, 28, PAD_MUXSEL_GPIO)
+#define MX23_PAD_PWM3__GPO_1_29			MXS_IOMUX_PAD_NAKED(1, 29, PAD_MUXSEL_GPIO)
+#define MX23_PAD_PWM4__GPO_1_30			MXS_IOMUX_PAD_NAKED(1, 30, PAD_MUXSEL_GPIO)
+
+#define MX23_PAD_SSP1_CMD__GPO_2_0		MXS_IOMUX_PAD_NAKED(2,  0, PAD_MUXSEL_GPIO)
+#define MX23_PAD_SSP1_DETECT__GPO_2_1		MXS_IOMUX_PAD_NAKED(2,  1, PAD_MUXSEL_GPIO)
+#define MX23_PAD_SSP1_DATA0__GPO_2_2		MXS_IOMUX_PAD_NAKED(2,  2, PAD_MUXSEL_GPIO)
+#define MX23_PAD_SSP1_DATA1__GPO_2_3		MXS_IOMUX_PAD_NAKED(2,  3, PAD_MUXSEL_GPIO)
+#define MX23_PAD_SSP1_DATA2__GPO_2_4		MXS_IOMUX_PAD_NAKED(2,  4, PAD_MUXSEL_GPIO)
+#define MX23_PAD_SSP1_DATA3__GPO_2_5		MXS_IOMUX_PAD_NAKED(2,  5, PAD_MUXSEL_GPIO)
+#define MX23_PAD_SSP1_SCK__GPO_2_6		MXS_IOMUX_PAD_NAKED(2,  6, PAD_MUXSEL_GPIO)
+#define MX23_PAD_ROTARYA__GPO_2_7		MXS_IOMUX_PAD_NAKED(2,  7, PAD_MUXSEL_GPIO)
+#define MX23_PAD_ROTARYB__GPO_2_8		MXS_IOMUX_PAD_NAKED(2,  8, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A00__GPO_2_9		MXS_IOMUX_PAD_NAKED(2,  9, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A01__GPO_2_10		MXS_IOMUX_PAD_NAKED(2, 10, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A02__GPO_2_11		MXS_IOMUX_PAD_NAKED(2, 11, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A03__GPO_2_12		MXS_IOMUX_PAD_NAKED(2, 12, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A04__GPO_2_13		MXS_IOMUX_PAD_NAKED(2, 13, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A05__GPO_2_14		MXS_IOMUX_PAD_NAKED(2, 14, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A06__GPO_2_15		MXS_IOMUX_PAD_NAKED(2, 15, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A07__GPO_2_16		MXS_IOMUX_PAD_NAKED(2, 16, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A08__GPO_2_17		MXS_IOMUX_PAD_NAKED(2, 17, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A09__GPO_2_18		MXS_IOMUX_PAD_NAKED(2, 18, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A10__GPO_2_19		MXS_IOMUX_PAD_NAKED(2, 19, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A11__GPO_2_20		MXS_IOMUX_PAD_NAKED(2, 20, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_A12__GPO_2_21		MXS_IOMUX_PAD_NAKED(2, 21, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_BA0__GPO_2_22		MXS_IOMUX_PAD_NAKED(2, 22, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_BA1__GPO_2_23		MXS_IOMUX_PAD_NAKED(2, 23, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_CASN__GPO_2_24		MXS_IOMUX_PAD_NAKED(2, 24, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_CE0N__GPO_2_25		MXS_IOMUX_PAD_NAKED(2, 25, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_CE1N__GPO_2_26		MXS_IOMUX_PAD_NAKED(2, 26, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_CE1N__GPO_2_27		MXS_IOMUX_PAD_NAKED(2, 27, PAD_MUXSEL_GPIO)
+#define MX23_PAD_GPMI_CE0N__GPO_2_28		MXS_IOMUX_PAD_NAKED(2, 28, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_CKE__GPO_2_29		MXS_IOMUX_PAD_NAKED(2, 29, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_RASN__GPO_2_30		MXS_IOMUX_PAD_NAKED(2, 30, PAD_MUXSEL_GPIO)
+#define MX23_PAD_EMI_WEN__GPO_2_31		MXS_IOMUX_PAD_NAKED(2, 31, PAD_MUXSEL_GPIO)
+
+#endif /* __MACH_IOMUX_MX23_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/iomux-mx28.h b/arch/arm/mach-mxs/include/mach/iomux-mx28.h
new file mode 100644
index 0000000..f50fefd
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/iomux-mx28.h
@@ -0,0 +1,537 @@
+/*
+ * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __MACH_IOMUX_MX28_H__
+#define __MACH_IOMUX_MX28_H__
+
+#include <mach/iomux.h>
+
+/*
+ * The naming convention for the pad modes is MX28_PAD_<padname>__<padmode>
+ * If <padname> or <padmode> refers to a GPIO, it is named GPIO_<unit>_<num>
+ * See also iomux.h
+ *
+ *									BANK	PIN	MUX
+ */
+/* MUXSEL_0 */
+#define MX28_PAD_GPMI_D00__GPMI_D0			MXS_IOMUX_PAD_NAKED(0,  0, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_D01__GPMI_D1			MXS_IOMUX_PAD_NAKED(0,  1, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_D02__GPMI_D2			MXS_IOMUX_PAD_NAKED(0,  2, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_D03__GPMI_D3			MXS_IOMUX_PAD_NAKED(0,  3, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_D04__GPMI_D4			MXS_IOMUX_PAD_NAKED(0,  4, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_D05__GPMI_D5			MXS_IOMUX_PAD_NAKED(0,  5, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_D06__GPMI_D6			MXS_IOMUX_PAD_NAKED(0,  6, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_D07__GPMI_D7			MXS_IOMUX_PAD_NAKED(0,  7, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_CE0N__GPMI_CE0N			MXS_IOMUX_PAD_NAKED(0, 16, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_CE1N__GPMI_CE1N			MXS_IOMUX_PAD_NAKED(0, 17, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_CE2N__GPMI_CE2N			MXS_IOMUX_PAD_NAKED(0, 18, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_CE3N__GPMI_CE3N			MXS_IOMUX_PAD_NAKED(0, 19, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_RDY0__GPMI_READY0			MXS_IOMUX_PAD_NAKED(0, 20, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_RDY1__GPMI_READY1			MXS_IOMUX_PAD_NAKED(0, 21, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_RDY2__GPMI_READY2			MXS_IOMUX_PAD_NAKED(0, 22, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_RDY3__GPMI_READY3			MXS_IOMUX_PAD_NAKED(0, 23, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_RDN__GPMI_RDN			MXS_IOMUX_PAD_NAKED(0, 24, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_WRN__GPMI_WRN			MXS_IOMUX_PAD_NAKED(0, 25, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_ALE__GPMI_ALE			MXS_IOMUX_PAD_NAKED(0, 26, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_CLE__GPMI_CLE			MXS_IOMUX_PAD_NAKED(0, 27, PAD_MUXSEL_0)
+#define MX28_PAD_GPMI_RESETN__GPMI_RESETN		MXS_IOMUX_PAD_NAKED(0, 28, PAD_MUXSEL_0)
+
+#define MX28_PAD_LCD_D00__LCD_D0			MXS_IOMUX_PAD_NAKED(1,  0, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D01__LCD_D1			MXS_IOMUX_PAD_NAKED(1,  1, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D02__LCD_D2			MXS_IOMUX_PAD_NAKED(1,  2, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D03__LCD_D3			MXS_IOMUX_PAD_NAKED(1,  3, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D04__LCD_D4			MXS_IOMUX_PAD_NAKED(1,  4, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D05__LCD_D5			MXS_IOMUX_PAD_NAKED(1,  5, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D06__LCD_D6			MXS_IOMUX_PAD_NAKED(1,  6, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D07__LCD_D7			MXS_IOMUX_PAD_NAKED(1,  7, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D08__LCD_D8			MXS_IOMUX_PAD_NAKED(1,  8, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D09__LCD_D9			MXS_IOMUX_PAD_NAKED(1,  9, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D10__LCD_D10			MXS_IOMUX_PAD_NAKED(1, 10, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D11__LCD_D11			MXS_IOMUX_PAD_NAKED(1, 11, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D12__LCD_D12			MXS_IOMUX_PAD_NAKED(1, 12, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D13__LCD_D13			MXS_IOMUX_PAD_NAKED(1, 13, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D14__LCD_D14			MXS_IOMUX_PAD_NAKED(1, 14, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D15__LCD_D15			MXS_IOMUX_PAD_NAKED(1, 15, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D16__LCD_D16			MXS_IOMUX_PAD_NAKED(1, 16, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D17__LCD_D17			MXS_IOMUX_PAD_NAKED(1, 17, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D18__LCD_D18			MXS_IOMUX_PAD_NAKED(1, 18, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D19__LCD_D19			MXS_IOMUX_PAD_NAKED(1, 19, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D20__LCD_D20			MXS_IOMUX_PAD_NAKED(1, 20, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D21__LCD_D21			MXS_IOMUX_PAD_NAKED(1, 21, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D22__LCD_D22			MXS_IOMUX_PAD_NAKED(1, 22, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_D23__LCD_D23			MXS_IOMUX_PAD_NAKED(1, 23, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_RD_E__LCD_RD_E			MXS_IOMUX_PAD_NAKED(1, 24, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_WR_RWN__LCD_WR_RWN			MXS_IOMUX_PAD_NAKED(1, 25, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_RS__LCD_RS				MXS_IOMUX_PAD_NAKED(1, 26, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_CS__LCD_CS				MXS_IOMUX_PAD_NAKED(1, 27, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_VSYNC__LCD_VSYNC			MXS_IOMUX_PAD_NAKED(1, 28, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_HSYNC__LCD_HSYNC			MXS_IOMUX_PAD_NAKED(1, 29, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_DOTCLK__LCD_DOTCLK			MXS_IOMUX_PAD_NAKED(1, 30, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_ENABLE__LCD_ENABLE			MXS_IOMUX_PAD_NAKED(1, 31, PAD_MUXSEL_0)
+
+#define MX28_PAD_SSP0_DATA0__SSP0_D0			MXS_IOMUX_PAD_NAKED(2,  0, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_DATA1__SSP0_D1			MXS_IOMUX_PAD_NAKED(2,  1, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_DATA2__SSP0_D2			MXS_IOMUX_PAD_NAKED(2,  2, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_DATA3__SSP0_D3			MXS_IOMUX_PAD_NAKED(2,  3, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_DATA4__SSP0_D4			MXS_IOMUX_PAD_NAKED(2,  4, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_DATA5__SSP0_D5			MXS_IOMUX_PAD_NAKED(2,  5, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_DATA6__SSP0_D6			MXS_IOMUX_PAD_NAKED(2,  6, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_DATA7__SSP0_D7			MXS_IOMUX_PAD_NAKED(2,  7, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_CMD__SSP0_CMD			MXS_IOMUX_PAD_NAKED(2,  8, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT		MXS_IOMUX_PAD_NAKED(2,  9, PAD_MUXSEL_0)
+#define MX28_PAD_SSP0_SCK__SSP0_SCK			MXS_IOMUX_PAD_NAKED(2, 10, PAD_MUXSEL_0)
+#define MX28_PAD_SSP1_SCK__SSP1_SCK			MXS_IOMUX_PAD_NAKED(2, 12, PAD_MUXSEL_0)
+#define MX28_PAD_SSP1_CMD__SSP1_CMD			MXS_IOMUX_PAD_NAKED(2, 13, PAD_MUXSEL_0)
+#define MX28_PAD_SSP1_DATA0__SSP1_D0			MXS_IOMUX_PAD_NAKED(2, 14, PAD_MUXSEL_0)
+#define MX28_PAD_SSP1_DATA3__SSP1_D3			MXS_IOMUX_PAD_NAKED(2, 15, PAD_MUXSEL_0)
+#define MX28_PAD_SSP2_SCK__SSP2_SCK			MXS_IOMUX_PAD_NAKED(2, 16, PAD_MUXSEL_0)
+#define MX28_PAD_SSP2_MOSI__SSP2_CMD			MXS_IOMUX_PAD_NAKED(2, 17, PAD_MUXSEL_0)
+#define MX28_PAD_SSP2_MISO__SSP2_D0			MXS_IOMUX_PAD_NAKED(2, 18, PAD_MUXSEL_0)
+#define MX28_PAD_SSP2_SS0__SSP2_D3			MXS_IOMUX_PAD_NAKED(2, 19, PAD_MUXSEL_0)
+#define MX28_PAD_SSP2_SS1__SSP2_D4			MXS_IOMUX_PAD_NAKED(2, 20, PAD_MUXSEL_0)
+#define MX28_PAD_SSP2_SS2__SSP2_D5			MXS_IOMUX_PAD_NAKED(2, 21, PAD_MUXSEL_0)
+#define MX28_PAD_SSP3_SCK__SSP3_SCK			MXS_IOMUX_PAD_NAKED(2, 24, PAD_MUXSEL_0)
+#define MX28_PAD_SSP3_MOSI__SSP3_CMD			MXS_IOMUX_PAD_NAKED(2, 25, PAD_MUXSEL_0)
+#define MX28_PAD_SSP3_MISO__SSP3_D0			MXS_IOMUX_PAD_NAKED(2, 26, PAD_MUXSEL_0)
+#define MX28_PAD_SSP3_SS0__SSP3_D3			MXS_IOMUX_PAD_NAKED(2, 27, PAD_MUXSEL_0)
+
+#define MX28_PAD_AUART0_RX__AUART0_RX			MXS_IOMUX_PAD_NAKED(3,  0, PAD_MUXSEL_0)
+#define MX28_PAD_AUART0_TX__AUART0_TX			MXS_IOMUX_PAD_NAKED(3,  1, PAD_MUXSEL_0)
+#define MX28_PAD_AUART0_CTS__AUART0_CTS			MXS_IOMUX_PAD_NAKED(3,  2, PAD_MUXSEL_0)
+#define MX28_PAD_AUART0_RTS__AUART0_RTS			MXS_IOMUX_PAD_NAKED(3,  3, PAD_MUXSEL_0)
+#define MX28_PAD_AUART1_RX__AUART1_RX			MXS_IOMUX_PAD_NAKED(3,  4, PAD_MUXSEL_0)
+#define MX28_PAD_AUART1_TX__AUART1_TX			MXS_IOMUX_PAD_NAKED(3,  5, PAD_MUXSEL_0)
+#define MX28_PAD_AUART1_CTS__AUART1_CTS			MXS_IOMUX_PAD_NAKED(3,  6, PAD_MUXSEL_0)
+#define MX28_PAD_AUART1_RTS__AUART1_RTS			MXS_IOMUX_PAD_NAKED(3,  7, PAD_MUXSEL_0)
+#define MX28_PAD_AUART2_RX__AUART2_RX			MXS_IOMUX_PAD_NAKED(3,  8, PAD_MUXSEL_0)
+#define MX28_PAD_AUART2_TX__AUART2_TX			MXS_IOMUX_PAD_NAKED(3,  9, PAD_MUXSEL_0)
+#define MX28_PAD_AUART2_CTS__AUART2_CTS			MXS_IOMUX_PAD_NAKED(3, 10, PAD_MUXSEL_0)
+#define MX28_PAD_AUART2_RTS__AUART2_RTS			MXS_IOMUX_PAD_NAKED(3, 11, PAD_MUXSEL_0)
+#define MX28_PAD_AUART3_RX__AUART3_RX			MXS_IOMUX_PAD_NAKED(3, 12, PAD_MUXSEL_0)
+#define MX28_PAD_AUART3_TX__AUART3_TX			MXS_IOMUX_PAD_NAKED(3, 13, PAD_MUXSEL_0)
+#define MX28_PAD_AUART3_CTS__AUART3_CTS			MXS_IOMUX_PAD_NAKED(3, 14, PAD_MUXSEL_0)
+#define MX28_PAD_AUART3_RTS__AUART3_RTS			MXS_IOMUX_PAD_NAKED(3, 15, PAD_MUXSEL_0)
+#define MX28_PAD_PWM0__PWM_0				MXS_IOMUX_PAD_NAKED(3, 16, PAD_MUXSEL_0)
+#define MX28_PAD_PWM1__PWM_1				MXS_IOMUX_PAD_NAKED(3, 17, PAD_MUXSEL_0)
+#define MX28_PAD_PWM2__PWM_2				MXS_IOMUX_PAD_NAKED(3, 18, PAD_MUXSEL_0)
+#define MX28_PAD_SAIF0_MCLK__SAIF0_MCLK			MXS_IOMUX_PAD_NAKED(3, 20, PAD_MUXSEL_0)
+#define MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK		MXS_IOMUX_PAD_NAKED(3, 21, PAD_MUXSEL_0)
+#define MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK		MXS_IOMUX_PAD_NAKED(3, 22, PAD_MUXSEL_0)
+#define MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0		MXS_IOMUX_PAD_NAKED(3, 23, PAD_MUXSEL_0)
+#define MX28_PAD_I2C0_SCL__I2C0_SCL			MXS_IOMUX_PAD_NAKED(3, 24, PAD_MUXSEL_0)
+#define MX28_PAD_I2C0_SDA__I2C0_SDA			MXS_IOMUX_PAD_NAKED(3, 25, PAD_MUXSEL_0)
+#define MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0		MXS_IOMUX_PAD_NAKED(3, 26, PAD_MUXSEL_0)
+#define MX28_PAD_SPDIF__SPDIF_TX			MXS_IOMUX_PAD_NAKED(3, 27, PAD_MUXSEL_0)
+#define MX28_PAD_PWM3__PWM_3				MXS_IOMUX_PAD_NAKED(3, 28, PAD_MUXSEL_0)
+#define MX28_PAD_PWM4__PWM_4				MXS_IOMUX_PAD_NAKED(3, 29, PAD_MUXSEL_0)
+#define MX28_PAD_LCD_RESET__LCD_RESET			MXS_IOMUX_PAD_NAKED(3, 30, PAD_MUXSEL_0)
+
+#define MX28_PAD_ENET0_MDC__ENET0_MDC			MXS_IOMUX_PAD_NAKED(4,  0, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_MDIO__ENET0_MDIO			MXS_IOMUX_PAD_NAKED(4,  1, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_RX_EN__ENET0_RX_EN		MXS_IOMUX_PAD_NAKED(4,  2, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_RXD0__ENET0_RXD0			MXS_IOMUX_PAD_NAKED(4,  3, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_RXD1__ENET0_RXD1			MXS_IOMUX_PAD_NAKED(4,  4, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_TX_CLK__ENET0_TX_CLK		MXS_IOMUX_PAD_NAKED(4,  5, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_TX_EN__ENET0_TX_EN		MXS_IOMUX_PAD_NAKED(4,  6, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_TXD0__ENET0_TXD0			MXS_IOMUX_PAD_NAKED(4,  7, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_TXD1__ENET0_TXD1			MXS_IOMUX_PAD_NAKED(4,  8, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_RXD2__ENET0_RXD2			MXS_IOMUX_PAD_NAKED(4,  9, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_RXD3__ENET0_RXD3			MXS_IOMUX_PAD_NAKED(4, 10, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_TXD2__ENET0_TXD2			MXS_IOMUX_PAD_NAKED(4, 11, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_TXD3__ENET0_TXD3			MXS_IOMUX_PAD_NAKED(4, 12, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_RX_CLK__ENET0_RX_CLK		MXS_IOMUX_PAD_NAKED(4, 13, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_COL__ENET0_COL			MXS_IOMUX_PAD_NAKED(4, 14, PAD_MUXSEL_0)
+#define MX28_PAD_ENET0_CRS__ENET0_CRS			MXS_IOMUX_PAD_NAKED(4, 15, PAD_MUXSEL_0)
+#define MX28_PAD_ENET_CLK__CLKCTRL_ENET			MXS_IOMUX_PAD_NAKED(4, 16, PAD_MUXSEL_0)
+#define MX28_PAD_JTAG_RTCK__JTAG_RTCK			MXS_IOMUX_PAD_NAKED(4, 20, PAD_MUXSEL_0)
+
+#define MX28_PAD_EMI_D00__EMI_DATA0			MXS_IOMUX_PAD_NAKED(5,  0, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D01__EMI_DATA1			MXS_IOMUX_PAD_NAKED(5,  1, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D02__EMI_DATA2			MXS_IOMUX_PAD_NAKED(5,  2, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D03__EMI_DATA3			MXS_IOMUX_PAD_NAKED(5,  3, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D04__EMI_DATA4			MXS_IOMUX_PAD_NAKED(5,  4, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D05__EMI_DATA5			MXS_IOMUX_PAD_NAKED(5,  5, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D06__EMI_DATA6			MXS_IOMUX_PAD_NAKED(5,  6, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D07__EMI_DATA7			MXS_IOMUX_PAD_NAKED(5,  7, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D08__EMI_DATA8			MXS_IOMUX_PAD_NAKED(5,  8, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D09__EMI_DATA9			MXS_IOMUX_PAD_NAKED(5,  9, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D10__EMI_DATA10			MXS_IOMUX_PAD_NAKED(5, 10, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D11__EMI_DATA11			MXS_IOMUX_PAD_NAKED(5, 11, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D12__EMI_DATA12			MXS_IOMUX_PAD_NAKED(5, 12, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D13__EMI_DATA13			MXS_IOMUX_PAD_NAKED(5, 13, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D14__EMI_DATA14			MXS_IOMUX_PAD_NAKED(5, 14, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_D15__EMI_DATA15			MXS_IOMUX_PAD_NAKED(5, 15, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_ODT0__EMI_ODT0			MXS_IOMUX_PAD_NAKED(5, 16, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_DQM0__EMI_DQM0			MXS_IOMUX_PAD_NAKED(5, 17, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_ODT1__EMI_ODT1			MXS_IOMUX_PAD_NAKED(5, 18, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_DQM1__EMI_DQM1			MXS_IOMUX_PAD_NAKED(5, 19, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK	MXS_IOMUX_PAD_NAKED(5, 20, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_CLK__EMI_CLK			MXS_IOMUX_PAD_NAKED(5, 21, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_DQS0__EMI_DQS0			MXS_IOMUX_PAD_NAKED(5, 22, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_DQS1__EMI_DQS1			MXS_IOMUX_PAD_NAKED(5, 23, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN		MXS_IOMUX_PAD_NAKED(5, 26, PAD_MUXSEL_0)
+
+#define MX28_PAD_EMI_A00__EMI_ADDR0			MXS_IOMUX_PAD_NAKED(6,  0, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A01__EMI_ADDR1			MXS_IOMUX_PAD_NAKED(6,  1, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A02__EMI_ADDR2			MXS_IOMUX_PAD_NAKED(6,  2, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A03__EMI_ADDR3			MXS_IOMUX_PAD_NAKED(6,  3, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A04__EMI_ADDR4			MXS_IOMUX_PAD_NAKED(6,  4, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A05__EMI_ADDR5			MXS_IOMUX_PAD_NAKED(6,  5, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A06__EMI_ADDR6			MXS_IOMUX_PAD_NAKED(6,  6, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A07__EMI_ADDR7			MXS_IOMUX_PAD_NAKED(6,  7, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A08__EMI_ADDR8			MXS_IOMUX_PAD_NAKED(6,  8, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A09__EMI_ADDR9			MXS_IOMUX_PAD_NAKED(6,  9, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A10__EMI_ADDR10			MXS_IOMUX_PAD_NAKED(6, 10, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A11__EMI_ADDR11			MXS_IOMUX_PAD_NAKED(6, 11, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A12__EMI_ADDR12			MXS_IOMUX_PAD_NAKED(6, 12, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A13__EMI_ADDR13			MXS_IOMUX_PAD_NAKED(6, 13, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_A14__EMI_ADDR14			MXS_IOMUX_PAD_NAKED(6, 14, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_BA0__EMI_BA0			MXS_IOMUX_PAD_NAKED(6, 16, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_BA1__EMI_BA1			MXS_IOMUX_PAD_NAKED(6, 17, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_BA2__EMI_BA2			MXS_IOMUX_PAD_NAKED(6, 18, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_CASN__EMI_CASN			MXS_IOMUX_PAD_NAKED(6, 19, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_RASN__EMI_RASN			MXS_IOMUX_PAD_NAKED(6, 20, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_WEN__EMI_WEN			MXS_IOMUX_PAD_NAKED(6, 21, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_CE0N__EMI_CE0N			MXS_IOMUX_PAD_NAKED(6, 22, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_CE1N__EMI_CE1N			MXS_IOMUX_PAD_NAKED(6, 23, PAD_MUXSEL_0)
+#define MX28_PAD_EMI_CKE__EMI_CKE			MXS_IOMUX_PAD_NAKED(6, 24, PAD_MUXSEL_0)
+
+/* MUXSEL_1 */
+#define MX28_PAD_GPMI_D00__SSP1_D0			MXS_IOMUX_PAD_NAKED(0,  0, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_D01__SSP1_D1			MXS_IOMUX_PAD_NAKED(0,  1, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_D02__SSP1_D2			MXS_IOMUX_PAD_NAKED(0,  2, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_D03__SSP1_D3			MXS_IOMUX_PAD_NAKED(0,  3, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_D04__SSP1_D4			MXS_IOMUX_PAD_NAKED(0,  4, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_D05__SSP1_D5			MXS_IOMUX_PAD_NAKED(0,  5, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_D06__SSP1_D6			MXS_IOMUX_PAD_NAKED(0,  6, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_D07__SSP1_D7			MXS_IOMUX_PAD_NAKED(0,  7, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_CE0N__SSP3_D0			MXS_IOMUX_PAD_NAKED(0, 16, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_CE1N__SSP3_D3			MXS_IOMUX_PAD_NAKED(0, 17, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_CE2N__CAN1_TX			MXS_IOMUX_PAD_NAKED(0, 18, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_CE3N__CAN1_RX			MXS_IOMUX_PAD_NAKED(0, 19, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT		MXS_IOMUX_PAD_NAKED(0, 20, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_RDY1__SSP1_CMD			MXS_IOMUX_PAD_NAKED(0, 21, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_RDY2__CAN0_TX			MXS_IOMUX_PAD_NAKED(0, 22, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_RDY3__CAN0_RX			MXS_IOMUX_PAD_NAKED(0, 23, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_RDN__SSP3_SCK			MXS_IOMUX_PAD_NAKED(0, 24, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_WRN__SSP1_SCK			MXS_IOMUX_PAD_NAKED(0, 25, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_ALE__SSP3_D1			MXS_IOMUX_PAD_NAKED(0, 26, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_CLE__SSP3_D2			MXS_IOMUX_PAD_NAKED(0, 27, PAD_MUXSEL_1)
+#define MX28_PAD_GPMI_RESETN__SSP3_CMD			MXS_IOMUX_PAD_NAKED(0, 28, PAD_MUXSEL_1)
+
+#define MX28_PAD_LCD_D03__ETM_DA8			MXS_IOMUX_PAD_NAKED(1,  3, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_D04__ETM_DA9			MXS_IOMUX_PAD_NAKED(1,  4, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_D08__ETM_DA3			MXS_IOMUX_PAD_NAKED(1,  8, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_D09__ETM_DA4			MXS_IOMUX_PAD_NAKED(1,  9, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_D20__ENET1_1588_EVENT2_OUT		MXS_IOMUX_PAD_NAKED(1, 20, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_D21__ENET1_1588_EVENT2_IN		MXS_IOMUX_PAD_NAKED(1, 21, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_D22__ENET1_1588_EVENT3_OUT		MXS_IOMUX_PAD_NAKED(1, 22, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_D23__ENET1_1588_EVENT3_IN		MXS_IOMUX_PAD_NAKED(1, 23, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_RD_E__LCD_VSYNC			MXS_IOMUX_PAD_NAKED(1, 24, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_WR_RWN__LCD_HSYNC			MXS_IOMUX_PAD_NAKED(1, 25, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_RS__LCD_DOTCLK			MXS_IOMUX_PAD_NAKED(1, 26, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_CS__LCD_ENABLE			MXS_IOMUX_PAD_NAKED(1, 27, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_VSYNC__SAIF1_SDATA0		MXS_IOMUX_PAD_NAKED(1, 28, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_HSYNC__SAIF1_SDATA1		MXS_IOMUX_PAD_NAKED(1, 29, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_DOTCLK__SAIF1_MCLK			MXS_IOMUX_PAD_NAKED(1, 30, PAD_MUXSEL_1)
+
+#define MX28_PAD_SSP0_DATA4__SSP2_D0			MXS_IOMUX_PAD_NAKED(2,  4, PAD_MUXSEL_1)
+#define MX28_PAD_SSP0_DATA5__SSP2_D3			MXS_IOMUX_PAD_NAKED(2,  5, PAD_MUXSEL_1)
+#define MX28_PAD_SSP0_DATA6__SSP2_CMD			MXS_IOMUX_PAD_NAKED(2,  6, PAD_MUXSEL_1)
+#define MX28_PAD_SSP0_DATA7__SSP2_SCK			MXS_IOMUX_PAD_NAKED(2,  7, PAD_MUXSEL_1)
+#define MX28_PAD_SSP1_SCK__SSP2_D1			MXS_IOMUX_PAD_NAKED(2, 12, PAD_MUXSEL_1)
+#define MX28_PAD_SSP1_CMD__SSP2_D2			MXS_IOMUX_PAD_NAKED(2, 13, PAD_MUXSEL_1)
+#define MX28_PAD_SSP1_DATA0__SSP2_D6			MXS_IOMUX_PAD_NAKED(2, 14, PAD_MUXSEL_1)
+#define MX28_PAD_SSP1_DATA3__SSP2_D7			MXS_IOMUX_PAD_NAKED(2, 15, PAD_MUXSEL_1)
+#define MX28_PAD_SSP2_SCK__AUART2_RX			MXS_IOMUX_PAD_NAKED(2, 16, PAD_MUXSEL_1)
+#define MX28_PAD_SSP2_MOSI__AUART2_TX			MXS_IOMUX_PAD_NAKED(2, 17, PAD_MUXSEL_1)
+#define MX28_PAD_SSP2_MISO__AUART3_RX			MXS_IOMUX_PAD_NAKED(2, 18, PAD_MUXSEL_1)
+#define MX28_PAD_SSP2_SS0__AUART3_TX			MXS_IOMUX_PAD_NAKED(2, 19, PAD_MUXSEL_1)
+#define MX28_PAD_SSP2_SS1__SSP2_D1			MXS_IOMUX_PAD_NAKED(2, 20, PAD_MUXSEL_1)
+#define MX28_PAD_SSP2_SS2__SSP2_D2			MXS_IOMUX_PAD_NAKED(2, 21, PAD_MUXSEL_1)
+#define MX28_PAD_SSP3_SCK__AUART4_TX			MXS_IOMUX_PAD_NAKED(2, 24, PAD_MUXSEL_1)
+#define MX28_PAD_SSP3_MOSI__AUART4_RX			MXS_IOMUX_PAD_NAKED(2, 25, PAD_MUXSEL_1)
+#define MX28_PAD_SSP3_MISO__AUART4_RTS			MXS_IOMUX_PAD_NAKED(2, 26, PAD_MUXSEL_1)
+#define MX28_PAD_SSP3_SS0__AUART4_CTS			MXS_IOMUX_PAD_NAKED(2, 27, PAD_MUXSEL_1)
+
+#define MX28_PAD_AUART0_RX__I2C0_SCL			MXS_IOMUX_PAD_NAKED(3,  0, PAD_MUXSEL_1)
+#define MX28_PAD_AUART0_TX__I2C0_SDA			MXS_IOMUX_PAD_NAKED(3,  1, PAD_MUXSEL_1)
+#define MX28_PAD_AUART0_CTS__AUART4_RX			MXS_IOMUX_PAD_NAKED(3,  2, PAD_MUXSEL_1)
+#define MX28_PAD_AUART0_RTS__AUART4_TX			MXS_IOMUX_PAD_NAKED(3,  3, PAD_MUXSEL_1)
+#define MX28_PAD_AUART1_RX__SSP2_CARD_DETECT		MXS_IOMUX_PAD_NAKED(3,  4, PAD_MUXSEL_1)
+#define MX28_PAD_AUART1_TX__SSP3_CARD_DETECT		MXS_IOMUX_PAD_NAKED(3,  5, PAD_MUXSEL_1)
+#define MX28_PAD_AUART1_CTS__USB0_OVERCURRENT		MXS_IOMUX_PAD_NAKED(3,  6, PAD_MUXSEL_1)
+#define MX28_PAD_AUART1_RTS__USB0_ID			MXS_IOMUX_PAD_NAKED(3,  7, PAD_MUXSEL_1)
+#define MX28_PAD_AUART2_RX__SSP3_D1			MXS_IOMUX_PAD_NAKED(3,  8, PAD_MUXSEL_1)
+#define MX28_PAD_AUART2_TX__SSP3_D2			MXS_IOMUX_PAD_NAKED(3,  9, PAD_MUXSEL_1)
+#define MX28_PAD_AUART2_CTS__I2C1_SCL			MXS_IOMUX_PAD_NAKED(3, 10, PAD_MUXSEL_1)
+#define MX28_PAD_AUART2_RTS__I2C1_SDA			MXS_IOMUX_PAD_NAKED(3, 11, PAD_MUXSEL_1)
+#define MX28_PAD_AUART3_RX__CAN0_TX			MXS_IOMUX_PAD_NAKED(3, 12, PAD_MUXSEL_1)
+#define MX28_PAD_AUART3_TX__CAN0_RX			MXS_IOMUX_PAD_NAKED(3, 13, PAD_MUXSEL_1)
+#define MX28_PAD_AUART3_CTS__CAN1_TX			MXS_IOMUX_PAD_NAKED(3, 14, PAD_MUXSEL_1)
+#define MX28_PAD_AUART3_RTS__CAN1_RX			MXS_IOMUX_PAD_NAKED(3, 15, PAD_MUXSEL_1)
+#define MX28_PAD_PWM0__I2C1_SCL				MXS_IOMUX_PAD_NAKED(3, 16, PAD_MUXSEL_1)
+#define MX28_PAD_PWM1__I2C1_SDA				MXS_IOMUX_PAD_NAKED(3, 17, PAD_MUXSEL_1)
+#define MX28_PAD_PWM2__USB0_ID				MXS_IOMUX_PAD_NAKED(3, 18, PAD_MUXSEL_1)
+#define MX28_PAD_SAIF0_MCLK__PWM_3			MXS_IOMUX_PAD_NAKED(3, 20, PAD_MUXSEL_1)
+#define MX28_PAD_SAIF0_LRCLK__PWM_4			MXS_IOMUX_PAD_NAKED(3, 21, PAD_MUXSEL_1)
+#define MX28_PAD_SAIF0_BITCLK__PWM_5			MXS_IOMUX_PAD_NAKED(3, 22, PAD_MUXSEL_1)
+#define MX28_PAD_SAIF0_SDATA0__PWM_6			MXS_IOMUX_PAD_NAKED(3, 23, PAD_MUXSEL_1)
+#define MX28_PAD_I2C0_SCL__TIMROT_ROTARYA		MXS_IOMUX_PAD_NAKED(3, 24, PAD_MUXSEL_1)
+#define MX28_PAD_I2C0_SDA__TIMROT_ROTARYB		MXS_IOMUX_PAD_NAKED(3, 25, PAD_MUXSEL_1)
+#define MX28_PAD_SAIF1_SDATA0__PWM_7			MXS_IOMUX_PAD_NAKED(3, 26, PAD_MUXSEL_1)
+#define MX28_PAD_LCD_RESET__LCD_VSYNC			MXS_IOMUX_PAD_NAKED(3, 30, PAD_MUXSEL_1)
+
+#define MX28_PAD_ENET0_MDC__GPMI_CE4N			MXS_IOMUX_PAD_NAKED(4,  0, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_MDIO__GPMI_CE5N			MXS_IOMUX_PAD_NAKED(4,  1, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_RX_EN__GPMI_CE6N			MXS_IOMUX_PAD_NAKED(4,  2, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_RXD0__GPMI_CE7N			MXS_IOMUX_PAD_NAKED(4,  3, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_RXD1__GPMI_READY4		MXS_IOMUX_PAD_NAKED(4,  4, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_TX_CLK__HSADC_TRIGGER		MXS_IOMUX_PAD_NAKED(4,  5, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_TX_EN__GPMI_READY5		MXS_IOMUX_PAD_NAKED(4,  6, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_TXD0__GPMI_READY6		MXS_IOMUX_PAD_NAKED(4,  7, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_TXD1__GPMI_READY7		MXS_IOMUX_PAD_NAKED(4,  8, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_RXD2__ENET1_RXD0			MXS_IOMUX_PAD_NAKED(4,  9, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_RXD3__ENET1_RXD1			MXS_IOMUX_PAD_NAKED(4, 10, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_TXD2__ENET1_TXD0			MXS_IOMUX_PAD_NAKED(4, 11, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_TXD3__ENET1_TXD1			MXS_IOMUX_PAD_NAKED(4, 12, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_RX_CLK__ENET0_RX_ER		MXS_IOMUX_PAD_NAKED(4, 13, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_COL__ENET1_TX_EN			MXS_IOMUX_PAD_NAKED(4, 14, PAD_MUXSEL_1)
+#define MX28_PAD_ENET0_CRS__ENET1_RX_EN			MXS_IOMUX_PAD_NAKED(4, 15, PAD_MUXSEL_1)
+
+/* MUXSEL_2 */
+#define MX28_PAD_GPMI_CE2N__ENET0_RX_ER			MXS_IOMUX_PAD_NAKED(0, 18, PAD_MUXSEL_2)
+#define MX28_PAD_GPMI_CE3N__SAIF1_MCLK			MXS_IOMUX_PAD_NAKED(0, 19, PAD_MUXSEL_2)
+#define MX28_PAD_GPMI_RDY0__USB0_ID			MXS_IOMUX_PAD_NAKED(0, 20, PAD_MUXSEL_2)
+#define MX28_PAD_GPMI_RDY2__ENET0_TX_ER			MXS_IOMUX_PAD_NAKED(0, 22, PAD_MUXSEL_2)
+#define MX28_PAD_GPMI_RDY3__HSADC_TRIGGER		MXS_IOMUX_PAD_NAKED(0, 23, PAD_MUXSEL_2)
+#define MX28_PAD_GPMI_ALE__SSP3_D4			MXS_IOMUX_PAD_NAKED(0, 26, PAD_MUXSEL_2)
+#define MX28_PAD_GPMI_CLE__SSP3_D5			MXS_IOMUX_PAD_NAKED(0, 27, PAD_MUXSEL_2)
+
+#define MX28_PAD_LCD_D00__ETM_DA0			MXS_IOMUX_PAD_NAKED(1,  0, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D01__ETM_DA1			MXS_IOMUX_PAD_NAKED(1,  1, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D02__ETM_DA2			MXS_IOMUX_PAD_NAKED(1,  2, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D03__ETM_DA3			MXS_IOMUX_PAD_NAKED(1,  3, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D04__ETM_DA4			MXS_IOMUX_PAD_NAKED(1,  4, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D05__ETM_DA5			MXS_IOMUX_PAD_NAKED(1,  5, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D06__ETM_DA6			MXS_IOMUX_PAD_NAKED(1,  6, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D07__ETM_DA7			MXS_IOMUX_PAD_NAKED(1,  7, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D08__ETM_DA8			MXS_IOMUX_PAD_NAKED(1,  8, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D09__ETM_DA9			MXS_IOMUX_PAD_NAKED(1,  9, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D10__ETM_DA10			MXS_IOMUX_PAD_NAKED(1, 10, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D11__ETM_DA11			MXS_IOMUX_PAD_NAKED(1, 11, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D12__ETM_DA12			MXS_IOMUX_PAD_NAKED(1, 12, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D13__ETM_DA13			MXS_IOMUX_PAD_NAKED(1, 13, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D14__ETM_DA14			MXS_IOMUX_PAD_NAKED(1, 14, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D15__ETM_DA15			MXS_IOMUX_PAD_NAKED(1, 15, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D16__ETM_DA7			MXS_IOMUX_PAD_NAKED(1, 16, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D17__ETM_DA6			MXS_IOMUX_PAD_NAKED(1, 17, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D18__ETM_DA5			MXS_IOMUX_PAD_NAKED(1, 18, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D19__ETM_DA4			MXS_IOMUX_PAD_NAKED(1, 19, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D20__ETM_DA3			MXS_IOMUX_PAD_NAKED(1, 20, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D21__ETM_DA2			MXS_IOMUX_PAD_NAKED(1, 21, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D22__ETM_DA1			MXS_IOMUX_PAD_NAKED(1, 22, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_D23__ETM_DA0			MXS_IOMUX_PAD_NAKED(1, 23, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_RD_E__ETM_TCTL			MXS_IOMUX_PAD_NAKED(1, 24, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_WR_RWN__ETM_TCLK			MXS_IOMUX_PAD_NAKED(1, 25, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_HSYNC__ETM_TCTL			MXS_IOMUX_PAD_NAKED(1, 29, PAD_MUXSEL_2)
+#define MX28_PAD_LCD_DOTCLK__ETM_TCLK			MXS_IOMUX_PAD_NAKED(1, 30, PAD_MUXSEL_2)
+
+#define MX28_PAD_SSP1_SCK__ENET0_1588_EVENT2_OUT	MXS_IOMUX_PAD_NAKED(2, 12, PAD_MUXSEL_2)
+#define MX28_PAD_SSP1_CMD__ENET0_1588_EVENT2_IN		MXS_IOMUX_PAD_NAKED(2, 13, PAD_MUXSEL_2)
+#define MX28_PAD_SSP1_DATA0__ENET0_1588_EVENT3_OUT	MXS_IOMUX_PAD_NAKED(2, 14, PAD_MUXSEL_2)
+#define MX28_PAD_SSP1_DATA3__ENET0_1588_EVENT3_IN	MXS_IOMUX_PAD_NAKED(2, 15, PAD_MUXSEL_2)
+#define MX28_PAD_SSP2_SCK__SAIF0_SDATA1			MXS_IOMUX_PAD_NAKED(2, 16, PAD_MUXSEL_2)
+#define MX28_PAD_SSP2_MOSI__SAIF0_SDATA2		MXS_IOMUX_PAD_NAKED(2, 17, PAD_MUXSEL_2)
+#define MX28_PAD_SSP2_MISO__SAIF1_SDATA1		MXS_IOMUX_PAD_NAKED(2, 18, PAD_MUXSEL_2)
+#define MX28_PAD_SSP2_SS0__SAIF1_SDATA2			MXS_IOMUX_PAD_NAKED(2, 19, PAD_MUXSEL_2)
+#define MX28_PAD_SSP2_SS1__USB1_OVERCURRENT		MXS_IOMUX_PAD_NAKED(2, 20, PAD_MUXSEL_2)
+#define MX28_PAD_SSP2_SS2__USB0_OVERCURRENT		MXS_IOMUX_PAD_NAKED(2, 21, PAD_MUXSEL_2)
+#define MX28_PAD_SSP3_SCK__ENET1_1588_EVENT0_OUT	MXS_IOMUX_PAD_NAKED(2, 24, PAD_MUXSEL_2)
+#define MX28_PAD_SSP3_MOSI__ENET1_1588_EVENT0_IN	MXS_IOMUX_PAD_NAKED(2, 25, PAD_MUXSEL_2)
+#define MX28_PAD_SSP3_MISO__ENET1_1588_EVENT1_OUT	MXS_IOMUX_PAD_NAKED(2, 26, PAD_MUXSEL_2)
+#define MX28_PAD_SSP3_SS0__ENET1_1588_EVENT1_IN		MXS_IOMUX_PAD_NAKED(2, 27, PAD_MUXSEL_2)
+
+#define MX28_PAD_AUART0_RX__DUART_CTS			MXS_IOMUX_PAD_NAKED(3,  0, PAD_MUXSEL_2)
+#define MX28_PAD_AUART0_TX__DUART_RTS			MXS_IOMUX_PAD_NAKED(3,  1, PAD_MUXSEL_2)
+#define MX28_PAD_AUART0_CTS__DUART_RX			MXS_IOMUX_PAD_NAKED(3,  2, PAD_MUXSEL_2)
+#define MX28_PAD_AUART0_RTS__DUART_TX			MXS_IOMUX_PAD_NAKED(3,  3, PAD_MUXSEL_2)
+#define MX28_PAD_AUART1_RX__PWM_0			MXS_IOMUX_PAD_NAKED(3,  4, PAD_MUXSEL_2)
+#define MX28_PAD_AUART1_TX__PWM_1			MXS_IOMUX_PAD_NAKED(3,  5, PAD_MUXSEL_2)
+#define MX28_PAD_AUART1_CTS__TIMROT_ROTARYA		MXS_IOMUX_PAD_NAKED(3,  6, PAD_MUXSEL_2)
+#define MX28_PAD_AUART1_RTS__TIMROT_ROTARYB		MXS_IOMUX_PAD_NAKED(3,  7, PAD_MUXSEL_2)
+#define MX28_PAD_AUART2_RX__SSP3_D4			MXS_IOMUX_PAD_NAKED(3,  8, PAD_MUXSEL_2)
+#define MX28_PAD_AUART2_TX__SSP3_D5			MXS_IOMUX_PAD_NAKED(3,  9, PAD_MUXSEL_2)
+#define MX28_PAD_AUART2_CTS__SAIF1_BITCLK		MXS_IOMUX_PAD_NAKED(3, 10, PAD_MUXSEL_2)
+#define MX28_PAD_AUART2_RTS__SAIF1_LRCLK		MXS_IOMUX_PAD_NAKED(3, 11, PAD_MUXSEL_2)
+#define MX28_PAD_AUART3_RX__ENET0_1588_EVENT0_OUT	MXS_IOMUX_PAD_NAKED(3, 12, PAD_MUXSEL_2)
+#define MX28_PAD_AUART3_TX__ENET0_1588_EVENT0_IN	MXS_IOMUX_PAD_NAKED(3, 13, PAD_MUXSEL_2)
+#define MX28_PAD_AUART3_CTS__ENET0_1588_EVENT1_OUT	MXS_IOMUX_PAD_NAKED(3, 14, PAD_MUXSEL_2)
+#define MX28_PAD_AUART3_RTS__ENET0_1588_EVENT1_IN	MXS_IOMUX_PAD_NAKED(3, 15, PAD_MUXSEL_2)
+#define MX28_PAD_PWM0__DUART_RX				MXS_IOMUX_PAD_NAKED(3, 16, PAD_MUXSEL_2)
+#define MX28_PAD_PWM1__DUART_TX				MXS_IOMUX_PAD_NAKED(3, 17, PAD_MUXSEL_2)
+#define MX28_PAD_PWM2__USB1_OVERCURRENT			MXS_IOMUX_PAD_NAKED(3, 18, PAD_MUXSEL_2)
+#define MX28_PAD_SAIF0_MCLK__AUART4_CTS			MXS_IOMUX_PAD_NAKED(3, 20, PAD_MUXSEL_2)
+#define MX28_PAD_SAIF0_LRCLK__AUART4_RTS		MXS_IOMUX_PAD_NAKED(3, 21, PAD_MUXSEL_2)
+#define MX28_PAD_SAIF0_BITCLK__AUART4_RX		MXS_IOMUX_PAD_NAKED(3, 22, PAD_MUXSEL_2)
+#define MX28_PAD_SAIF0_SDATA0__AUART4_TX		MXS_IOMUX_PAD_NAKED(3, 23, PAD_MUXSEL_2)
+#define MX28_PAD_I2C0_SCL__DUART_RX			MXS_IOMUX_PAD_NAKED(3, 24, PAD_MUXSEL_2)
+#define MX28_PAD_I2C0_SDA__DUART_TX			MXS_IOMUX_PAD_NAKED(3, 25, PAD_MUXSEL_2)
+#define MX28_PAD_SAIF1_SDATA0__SAIF0_SDATA1		MXS_IOMUX_PAD_NAKED(3, 26, PAD_MUXSEL_2)
+#define MX28_PAD_SPDIF__ENET1_RX_ER			MXS_IOMUX_PAD_NAKED(3, 27, PAD_MUXSEL_2)
+
+#define MX28_PAD_ENET0_MDC__SAIF0_SDATA1		MXS_IOMUX_PAD_NAKED(4,  0, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_MDIO__SAIF0_SDATA2		MXS_IOMUX_PAD_NAKED(4,  1, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_RX_EN__SAIF1_SDATA1		MXS_IOMUX_PAD_NAKED(4,  2, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_RXD0__SAIF1_SDATA2		MXS_IOMUX_PAD_NAKED(4,  3, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_TX_CLK__ENET0_1588_EVENT2_OUT	MXS_IOMUX_PAD_NAKED(4,  5, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_RXD2__ENET0_1588_EVENT0_OUT	MXS_IOMUX_PAD_NAKED(4,  9, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_RXD3__ENET0_1588_EVENT0_IN	MXS_IOMUX_PAD_NAKED(4, 10, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_TXD2__ENET0_1588_EVENT1_OUT	MXS_IOMUX_PAD_NAKED(4, 11, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_TXD3__ENET0_1588_EVENT1_IN	MXS_IOMUX_PAD_NAKED(4, 12, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_RX_CLK__ENET0_1588_EVENT2_IN	MXS_IOMUX_PAD_NAKED(4, 13, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_COL__ENET0_1588_EVENT3_OUT	MXS_IOMUX_PAD_NAKED(4, 14, PAD_MUXSEL_2)
+#define MX28_PAD_ENET0_CRS__ENET0_1588_EVENT3_IN	MXS_IOMUX_PAD_NAKED(4, 15, PAD_MUXSEL_2)
+
+/* MUXSEL_GPIO */
+#define MX28_PAD_GPMI_D00__GPIO_0_0			MXS_IOMUX_PAD_NAKED(0,  0, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_D01__GPIO_0_1			MXS_IOMUX_PAD_NAKED(0,  1, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_D02__GPIO_0_2			MXS_IOMUX_PAD_NAKED(0,  2, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_D03__GPIO_0_3			MXS_IOMUX_PAD_NAKED(0,  3, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_D04__GPIO_0_4			MXS_IOMUX_PAD_NAKED(0,  4, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_D05__GPIO_0_5			MXS_IOMUX_PAD_NAKED(0,  5, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_D06__GPIO_0_6			MXS_IOMUX_PAD_NAKED(0,  6, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_D07__GPIO_0_7			MXS_IOMUX_PAD_NAKED(0,  7, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_CE0N__GPIO_0_16			MXS_IOMUX_PAD_NAKED(0, 16, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_CE1N__GPIO_0_17			MXS_IOMUX_PAD_NAKED(0, 17, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_CE2N__GPIO_0_18			MXS_IOMUX_PAD_NAKED(0, 18, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_CE3N__GPIO_0_19			MXS_IOMUX_PAD_NAKED(0, 19, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_RDY0__GPIO_0_20			MXS_IOMUX_PAD_NAKED(0, 20, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_RDY1__GPIO_0_21			MXS_IOMUX_PAD_NAKED(0, 21, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_RDY2__GPIO_0_22			MXS_IOMUX_PAD_NAKED(0, 22, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_RDY3__GPIO_0_23			MXS_IOMUX_PAD_NAKED(0, 23, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_RDN__GPIO_0_24			MXS_IOMUX_PAD_NAKED(0, 24, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_WRN__GPIO_0_25			MXS_IOMUX_PAD_NAKED(0, 25, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_ALE__GPIO_0_26			MXS_IOMUX_PAD_NAKED(0, 26, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_CLE__GPIO_0_27			MXS_IOMUX_PAD_NAKED(0, 27, PAD_MUXSEL_GPIO)
+#define MX28_PAD_GPMI_RESETN__GPIO_0_28			MXS_IOMUX_PAD_NAKED(0, 28, PAD_MUXSEL_GPIO)
+
+#define MX28_PAD_LCD_D00__GPIO_1_0			MXS_IOMUX_PAD_NAKED(1,  0, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D01__GPIO_1_1			MXS_IOMUX_PAD_NAKED(1,  1, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D02__GPIO_1_2			MXS_IOMUX_PAD_NAKED(1,  2, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D03__GPIO_1_3			MXS_IOMUX_PAD_NAKED(1,  3, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D04__GPIO_1_4			MXS_IOMUX_PAD_NAKED(1,  4, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D05__GPIO_1_5			MXS_IOMUX_PAD_NAKED(1,  5, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D06__GPIO_1_6			MXS_IOMUX_PAD_NAKED(1,  6, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D07__GPIO_1_7			MXS_IOMUX_PAD_NAKED(1,  7, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D08__GPIO_1_8			MXS_IOMUX_PAD_NAKED(1,  8, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D09__GPIO_1_9			MXS_IOMUX_PAD_NAKED(1,  9, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D10__GPIO_1_10			MXS_IOMUX_PAD_NAKED(1, 10, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D11__GPIO_1_11			MXS_IOMUX_PAD_NAKED(1, 11, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D12__GPIO_1_12			MXS_IOMUX_PAD_NAKED(1, 12, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D13__GPIO_1_13			MXS_IOMUX_PAD_NAKED(1, 13, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D14__GPIO_1_14			MXS_IOMUX_PAD_NAKED(1, 14, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D15__GPIO_1_15			MXS_IOMUX_PAD_NAKED(1, 15, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D16__GPIO_1_16			MXS_IOMUX_PAD_NAKED(1, 16, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D17__GPIO_1_17			MXS_IOMUX_PAD_NAKED(1, 17, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D18__GPIO_1_18			MXS_IOMUX_PAD_NAKED(1, 18, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D19__GPIO_1_19			MXS_IOMUX_PAD_NAKED(1, 19, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D20__GPIO_1_20			MXS_IOMUX_PAD_NAKED(1, 20, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D21__GPIO_1_21			MXS_IOMUX_PAD_NAKED(1, 21, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D22__GPIO_1_22			MXS_IOMUX_PAD_NAKED(1, 22, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_D23__GPIO_1_23			MXS_IOMUX_PAD_NAKED(1, 23, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_RD_E__GPIO_1_24			MXS_IOMUX_PAD_NAKED(1, 24, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_WR_RWN__GPIO_1_25			MXS_IOMUX_PAD_NAKED(1, 25, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_RS__GPIO_1_26			MXS_IOMUX_PAD_NAKED(1, 26, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_CS__GPIO_1_27			MXS_IOMUX_PAD_NAKED(1, 27, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_VSYNC__GPIO_1_28			MXS_IOMUX_PAD_NAKED(1, 28, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_HSYNC__GPIO_1_29			MXS_IOMUX_PAD_NAKED(1, 29, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_DOTCLK__GPIO_1_30			MXS_IOMUX_PAD_NAKED(1, 30, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_ENABLE__GPIO_1_31			MXS_IOMUX_PAD_NAKED(1, 31, PAD_MUXSEL_GPIO)
+
+#define MX28_PAD_SSP0_DATA0__GPIO_2_0			MXS_IOMUX_PAD_NAKED(2,  0, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_DATA1__GPIO_2_1			MXS_IOMUX_PAD_NAKED(2,  1, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_DATA2__GPIO_2_2			MXS_IOMUX_PAD_NAKED(2,  2, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_DATA3__GPIO_2_3			MXS_IOMUX_PAD_NAKED(2,  3, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_DATA4__GPIO_2_4			MXS_IOMUX_PAD_NAKED(2,  4, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_DATA5__GPIO_2_5			MXS_IOMUX_PAD_NAKED(2,  5, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_DATA6__GPIO_2_6			MXS_IOMUX_PAD_NAKED(2,  6, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_DATA7__GPIO_2_7			MXS_IOMUX_PAD_NAKED(2,  7, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_CMD__GPIO_2_8			MXS_IOMUX_PAD_NAKED(2,  8, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_DETECT__GPIO_2_9			MXS_IOMUX_PAD_NAKED(2,  9, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP0_SCK__GPIO_2_10			MXS_IOMUX_PAD_NAKED(2, 10, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP1_SCK__GPIO_2_12			MXS_IOMUX_PAD_NAKED(2, 12, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP1_CMD__GPIO_2_13			MXS_IOMUX_PAD_NAKED(2, 13, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP1_DATA0__GPIO_2_14			MXS_IOMUX_PAD_NAKED(2, 14, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP1_DATA3__GPIO_2_15			MXS_IOMUX_PAD_NAKED(2, 15, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP2_SCK__GPIO_2_16			MXS_IOMUX_PAD_NAKED(2, 16, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP2_MOSI__GPIO_2_17			MXS_IOMUX_PAD_NAKED(2, 17, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP2_MISO__GPIO_2_18			MXS_IOMUX_PAD_NAKED(2, 18, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP2_SS0__GPIO_2_19			MXS_IOMUX_PAD_NAKED(2, 19, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP2_SS1__GPIO_2_20			MXS_IOMUX_PAD_NAKED(2, 20, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP2_SS2__GPIO_2_21			MXS_IOMUX_PAD_NAKED(2, 21, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP3_SCK__GPIO_2_24			MXS_IOMUX_PAD_NAKED(2, 24, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP3_MOSI__GPIO_2_25			MXS_IOMUX_PAD_NAKED(2, 25, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP3_MISO__GPIO_2_26			MXS_IOMUX_PAD_NAKED(2, 26, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SSP3_SS0__GPIO_2_27			MXS_IOMUX_PAD_NAKED(2, 27, PAD_MUXSEL_GPIO)
+
+#define MX28_PAD_AUART0_RX__GPIO_3_0			MXS_IOMUX_PAD_NAKED(3,  0, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART0_TX__GPIO_3_1			MXS_IOMUX_PAD_NAKED(3,  1, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART0_CTS__GPIO_3_2			MXS_IOMUX_PAD_NAKED(3,  2, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART0_RTS__GPIO_3_3			MXS_IOMUX_PAD_NAKED(3,  3, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART1_RX__GPIO_3_4			MXS_IOMUX_PAD_NAKED(3,  4, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART1_TX__GPIO_3_5			MXS_IOMUX_PAD_NAKED(3,  5, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART1_CTS__GPIO_3_6			MXS_IOMUX_PAD_NAKED(3,  6, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART1_RTS__GPIO_3_7			MXS_IOMUX_PAD_NAKED(3,  7, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART2_RX__GPIO_3_8			MXS_IOMUX_PAD_NAKED(3,  8, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART2_TX__GPIO_3_9			MXS_IOMUX_PAD_NAKED(3,  9, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART2_CTS__GPIO_3_10			MXS_IOMUX_PAD_NAKED(3, 10, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART2_RTS__GPIO_3_11			MXS_IOMUX_PAD_NAKED(3, 11, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART3_RX__GPIO_3_12			MXS_IOMUX_PAD_NAKED(3, 12, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART3_TX__GPIO_3_13			MXS_IOMUX_PAD_NAKED(3, 13, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART3_CTS__GPIO_3_14			MXS_IOMUX_PAD_NAKED(3, 14, PAD_MUXSEL_GPIO)
+#define MX28_PAD_AUART3_RTS__GPIO_3_15			MXS_IOMUX_PAD_NAKED(3, 15, PAD_MUXSEL_GPIO)
+#define MX28_PAD_PWM0__GPIO_3_16			MXS_IOMUX_PAD_NAKED(3, 16, PAD_MUXSEL_GPIO)
+#define MX28_PAD_PWM1__GPIO_3_17			MXS_IOMUX_PAD_NAKED(3, 17, PAD_MUXSEL_GPIO)
+#define MX28_PAD_PWM2__GPIO_3_18			MXS_IOMUX_PAD_NAKED(3, 18, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SAIF0_MCLK__GPIO_3_20			MXS_IOMUX_PAD_NAKED(3, 20, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SAIF0_LRCLK__GPIO_3_21			MXS_IOMUX_PAD_NAKED(3, 21, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SAIF0_BITCLK__GPIO_3_22		MXS_IOMUX_PAD_NAKED(3, 22, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SAIF0_SDATA0__GPIO_3_23		MXS_IOMUX_PAD_NAKED(3, 23, PAD_MUXSEL_GPIO)
+#define MX28_PAD_I2C0_SCL__GPIO_3_24			MXS_IOMUX_PAD_NAKED(3, 24, PAD_MUXSEL_GPIO)
+#define MX28_PAD_I2C0_SDA__GPIO_3_25			MXS_IOMUX_PAD_NAKED(3, 25, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SAIF1_SDATA0__GPIO_3_26		MXS_IOMUX_PAD_NAKED(3, 26, PAD_MUXSEL_GPIO)
+#define MX28_PAD_SPDIF__GPIO_3_27			MXS_IOMUX_PAD_NAKED(3, 27, PAD_MUXSEL_GPIO)
+#define MX28_PAD_PWM3__GPIO_3_28			MXS_IOMUX_PAD_NAKED(3, 28, PAD_MUXSEL_GPIO)
+#define MX28_PAD_PWM4__GPIO_3_29			MXS_IOMUX_PAD_NAKED(3, 29, PAD_MUXSEL_GPIO)
+#define MX28_PAD_LCD_RESET__GPIO_3_30			MXS_IOMUX_PAD_NAKED(3, 30, PAD_MUXSEL_GPIO)
+
+#define MX28_PAD_ENET0_MDC__GPIO_4_0			MXS_IOMUX_PAD_NAKED(4,  0, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_MDIO__GPIO_4_1			MXS_IOMUX_PAD_NAKED(4,  1, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_RX_EN__GPIO_4_2			MXS_IOMUX_PAD_NAKED(4,  2, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_RXD0__GPIO_4_3			MXS_IOMUX_PAD_NAKED(4,  3, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_RXD1__GPIO_4_4			MXS_IOMUX_PAD_NAKED(4,  4, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_TX_CLK__GPIO_4_5			MXS_IOMUX_PAD_NAKED(4,  5, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_TX_EN__GPIO_4_6			MXS_IOMUX_PAD_NAKED(4,  6, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_TXD0__GPIO_4_7			MXS_IOMUX_PAD_NAKED(4,  7, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_TXD1__GPIO_4_8			MXS_IOMUX_PAD_NAKED(4,  8, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_RXD2__GPIO_4_9			MXS_IOMUX_PAD_NAKED(4,  9, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_RXD3__GPIO_4_10			MXS_IOMUX_PAD_NAKED(4, 10, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_TXD2__GPIO_4_11			MXS_IOMUX_PAD_NAKED(4, 11, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_TXD3__GPIO_4_12			MXS_IOMUX_PAD_NAKED(4, 12, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_RX_CLK__GPIO_4_13		MXS_IOMUX_PAD_NAKED(4, 13, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_COL__GPIO_4_14			MXS_IOMUX_PAD_NAKED(4, 14, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET0_CRS__GPIO_4_15			MXS_IOMUX_PAD_NAKED(4, 15, PAD_MUXSEL_GPIO)
+#define MX28_PAD_ENET_CLK__GPIO_4_16			MXS_IOMUX_PAD_NAKED(4, 16, PAD_MUXSEL_GPIO)
+#define MX28_PAD_JTAG_RTCK__GPIO_4_20			MXS_IOMUX_PAD_NAKED(4, 20, PAD_MUXSEL_GPIO)
+
+#endif /* __MACH_IOMUX_MX28_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/iomux.h b/arch/arm/mach-mxs/include/mach/iomux.h
new file mode 100644
index 0000000..fe558e3
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/iomux.h
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
+ *			<armlinux@phytec.de>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef __MACH_MXS_IOMUX_H__
+#define __MACH_MXS_IOMUX_H__
+
+/*
+ * IOMUX/PAD Bit field definitions
+ *
+ * PAD_BANK:		 0..2	(3)
+ * PAD_PIN:		 3..7	(5)
+ * PAD_MUXSEL:		 8..9	(2)
+ * PAD_MA:		10..11	(2)
+ * PAD_MA_VALID:	12	(1)
+ * PAD_VOL:		13	(1)
+ * PAD_VOL_VALID:	14	(1)
+ * PAD_PULL:		15	(1)
+ * PAD_PULL_VALID:	16	(1)
+ * RESERVED:		17..31	(15)
+ */
+typedef u32 iomux_cfg_t;
+
+#define MXS_PAD_BANK_SHIFT	0
+#define MXS_PAD_BANK_MASK	((iomux_cfg_t)0x7 << MXS_PAD_BANK_SHIFT)
+#define MXS_PAD_PIN_SHIFT	3
+#define MXS_PAD_PIN_MASK	((iomux_cfg_t)0x1f << MXS_PAD_PIN_SHIFT)
+#define MXS_PAD_MUXSEL_SHIFT	8
+#define MXS_PAD_MUXSEL_MASK	((iomux_cfg_t)0x3 << MXS_PAD_MUXSEL_SHIFT)
+#define MXS_PAD_MA_SHIFT	10
+#define MXS_PAD_MA_MASK		((iomux_cfg_t)0x3 << MXS_PAD_MA_SHIFT)
+#define MXS_PAD_MA_VALID_SHIFT	12
+#define MXS_PAD_MA_VALID_MASK	((iomux_cfg_t)0x1 << MXS_PAD_MA_VALID_SHIFT)
+#define MXS_PAD_VOL_SHIFT	13
+#define MXS_PAD_VOL_MASK	((iomux_cfg_t)0x1 << MXS_PAD_VOL_SHIFT)
+#define MXS_PAD_VOL_VALID_SHIFT	14
+#define MXS_PAD_VOL_VALID_MASK	((iomux_cfg_t)0x1 << MXS_PAD_VOL_VALID_SHIFT)
+#define MXS_PAD_PULL_SHIFT	15
+#define MXS_PAD_PULL_MASK	((iomux_cfg_t)0x1 << MXS_PAD_PULL_SHIFT)
+#define MXS_PAD_PULL_VALID_SHIFT 16
+#define MXS_PAD_PULL_VALID_MASK	((iomux_cfg_t)0x1 << MXS_PAD_PULL_VALID_SHIFT)
+
+#define PAD_MUXSEL_0		0
+#define PAD_MUXSEL_1		1
+#define PAD_MUXSEL_2		2
+#define PAD_MUXSEL_GPIO		3
+
+#define PAD_4MA			0
+#define PAD_8MA			1
+#define PAD_12MA		2
+#define PAD_16MA		3
+
+#define PAD_1V8			0
+#define PAD_3V3			1
+
+#define PAD_NOPULL		0
+#define PAD_PULLUP		1
+
+#define MXS_PAD_4MA	((PAD_4MA << MXS_PAD_MA_SHIFT) | \
+					MXS_PAD_MA_VALID_MASK)
+#define MXS_PAD_8MA	((PAD_8MA << MXS_PAD_MA_SHIFT) | \
+					MXS_PAD_MA_VALID_MASK)
+#define MXS_PAD_12MA	((PAD_12MA << MXS_PAD_MA_SHIFT) | \
+					MXS_PAD_MA_VALID_MASK)
+#define MXS_PAD_16MA	((PAD_16MA << MXS_PAD_MA_SHIFT) | \
+					MXS_PAD_MA_VALID_MASK)
+
+#define MXS_PAD_1V8	((PAD_1V8 << MXS_PAD_VOL_SHIFT) | \
+					MXS_PAD_VOL_VALID_MASK)
+#define MXS_PAD_3V3	((PAD_3V3 << MXS_PAD_VOL_SHIFT) | \
+					MXS_PAD_VOL_VALID_MASK)
+
+#define MXS_PAD_NOPULL	((PAD_NOPULL << MXS_PAD_PULL_SHIFT) | \
+					MXS_PAD_PULL_VALID_MASK)
+#define MXS_PAD_PULLUP	((PAD_PULLUP << MXS_PAD_PULL_SHIFT) | \
+					MXS_PAD_PULL_VALID_MASK)
+
+#define MXS_IOMUX_PAD(_bank, _pin, _muxsel, _ma, _vol, _pull)		\
+		(((iomux_cfg_t)(_bank) << MXS_PAD_BANK_SHIFT) |		\
+		((iomux_cfg_t)(_pin) << MXS_PAD_PIN_SHIFT) |		\
+		((iomux_cfg_t)(_muxsel) << MXS_PAD_MUXSEL_SHIFT) |	\
+		((iomux_cfg_t)(_ma) << MXS_PAD_MA_SHIFT) |		\
+		((iomux_cfg_t)(_vol) << MXS_PAD_VOL_SHIFT) |		\
+		((iomux_cfg_t)(_pull) << MXS_PAD_PULL_SHIFT))
+
+/*
+ * A pad becomes naked, when none of mA, vol or pull
+ * validity bits is set.
+ */
+#define MXS_IOMUX_PAD_NAKED(_bank, _pin, _muxsel) \
+		MXS_IOMUX_PAD(_bank, _pin, _muxsel, 0, 0, 0)
+
+static inline unsigned int PAD_BANK(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_BANK_MASK) >> MXS_PAD_BANK_SHIFT;
+}
+
+static inline unsigned int PAD_PIN(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_PIN_MASK) >> MXS_PAD_PIN_SHIFT;
+}
+
+static inline unsigned int PAD_MUXSEL(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_MUXSEL_MASK) >> MXS_PAD_MUXSEL_SHIFT;
+}
+
+static inline unsigned int PAD_MA(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_MA_MASK) >> MXS_PAD_MA_SHIFT;
+}
+
+static inline unsigned int PAD_MA_VALID(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_MA_VALID_MASK) >> MXS_PAD_MA_VALID_SHIFT;
+}
+
+static inline unsigned int PAD_VOL(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_VOL_MASK) >> MXS_PAD_VOL_SHIFT;
+}
+
+static inline unsigned int PAD_VOL_VALID(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_VOL_VALID_MASK) >> MXS_PAD_VOL_VALID_SHIFT;
+}
+
+static inline unsigned int PAD_PULL(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_PULL_MASK) >> MXS_PAD_PULL_SHIFT;
+}
+
+static inline unsigned int PAD_PULL_VALID(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_PULL_VALID_MASK) >> MXS_PAD_PULL_VALID_SHIFT;
+}
+
+/*
+ * configures a single pad in the iomuxer
+ */
+int mxs_iomux_setup_pad(iomux_cfg_t pad);
+
+/*
+ * configures multiple pads
+ * convenient way to call the above function with tables
+ */
+int mxs_iomux_setup_multiple_pads(const iomux_cfg_t *pad_list, unsigned count);
+
+#endif /* __MACH_MXS_IOMUX_H__*/
diff --git a/arch/arm/mach-mxs/iomux.c b/arch/arm/mach-mxs/iomux.c
new file mode 100644
index 0000000..8c8cbf2
--- /dev/null
+++ b/arch/arm/mach-mxs/iomux.c
@@ -0,0 +1,101 @@
+/*
+ * Copyright 2004-2006,2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
+ * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
+ *                       <armlinux@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/gpio.h>
+
+#include <asm/mach/map.h>
+
+#include <mach/mxs.h>
+#include <mach/iomux.h>
+
+/*
+ * configures a single pad in the iomuxer
+ */
+int mxs_iomux_setup_pad(iomux_cfg_t pad)
+{
+	u32 reg, ofs, bp, bm;
+	void __iomem *iomux_base = MXS_IO_ADDRESS(MXS_PINCTRL_BASE_ADDR);
+
+	/* muxsel */
+	ofs = 0x100;
+	ofs += PAD_BANK(pad) * 0x20 + PAD_PIN(pad) / 16 * 0x10;
+	bp = PAD_PIN(pad) % 16 * 2;
+	bm = 0x3 << bp;
+	reg = __raw_readl(iomux_base + ofs);
+	reg &= ~bm;
+	reg |= PAD_MUXSEL(pad) << bp;
+	__raw_writel(reg, iomux_base + ofs);
+
+	/* drive */
+	ofs = cpu_is_mx23() ? 0x200 : 0x300;
+	ofs += PAD_BANK(pad) * 0x40 + PAD_PIN(pad) / 8 * 0x10;
+	/* mA */
+	if (PAD_MA_VALID(pad)) {
+		bp = PAD_PIN(pad) % 8 * 4;
+		bm = 0x3 << bp;
+		reg = __raw_readl(iomux_base + ofs);
+		reg &= ~bm;
+		reg |= PAD_MA(pad)  << bp;
+		__raw_writel(reg, iomux_base + ofs);
+	}
+	/* vol */
+	if (PAD_VOL_VALID(pad)) {
+		bp = PAD_PIN(pad) % 8 * 4 + 2;
+		if (PAD_VOL(pad))
+			__mxs_setl(1 << bp, iomux_base + ofs);
+		else
+			__mxs_clrl(1 << bp, iomux_base + ofs);
+	}
+
+	/* pull */
+	if (PAD_PULL_VALID(pad)) {
+		ofs = cpu_is_mx23() ? 0x400 : 0x600;
+		ofs += PAD_BANK(pad) * 0x10;
+		bp = PAD_PIN(pad);
+		if (PAD_PULL(pad))
+			__mxs_setl(1 << bp, iomux_base + ofs);
+		else
+			__mxs_clrl(1 << bp, iomux_base + ofs);
+	}
+
+	return 0;
+}
+
+int mxs_iomux_setup_multiple_pads(const iomux_cfg_t *pad_list, unsigned count)
+{
+	const iomux_cfg_t *p = pad_list;
+	int i;
+	int ret;
+
+	for (i = 0; i < count; i++) {
+		ret = mxs_iomux_setup_pad(*p);
+		if (ret)
+			return ret;
+		p++;
+	}
+
+	return 0;
+}
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v7 08/15] ARM: mxs: Add iomux support
  2010-12-18 13:39 ` [PATCH v7 08/15] ARM: mxs: Add iomux support Shawn Guo
@ 2010-12-20  9:44   ` Uwe Kleine-König
  0 siblings, 0 replies; 18+ messages in thread
From: Uwe Kleine-König @ 2010-12-20  9:44 UTC (permalink / raw)
  To: linux-arm-kernel

Hello Shawn

On Sat, Dec 18, 2010 at 09:39:32PM +0800, Shawn Guo wrote:
> MXS-based SoCs implements iomux functions in block PINCTRL.
> 
> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
> ---
> [...]
> diff --git a/arch/arm/mach-mxs/iomux.c b/arch/arm/mach-mxs/iomux.c
> new file mode 100644
> index 0000000..8c8cbf2
> --- /dev/null
> +++ b/arch/arm/mach-mxs/iomux.c
> @@ -0,0 +1,101 @@
> +[...]
> +/*
> + * configures a single pad in the iomuxer
> + */
> +int mxs_iomux_setup_pad(iomux_cfg_t pad)
> +{
> +	u32 reg, ofs, bp, bm;
> +	void __iomem *iomux_base = MXS_IO_ADDRESS(MXS_PINCTRL_BASE_ADDR);
> +
> +	/* muxsel */
> +	ofs = 0x100;
> +	ofs += PAD_BANK(pad) * 0x20 + PAD_PIN(pad) / 16 * 0x10;
> +	bp = PAD_PIN(pad) % 16 * 2;
> +	bm = 0x3 << bp;
> +	reg = __raw_readl(iomux_base + ofs);
> +	reg &= ~bm;
> +	reg |= PAD_MUXSEL(pad) << bp;
> +	__raw_writel(reg, iomux_base + ofs);
> +
> +	/* drive */
> +	ofs = cpu_is_mx23() ? 0x200 : 0x300;
> +	ofs += PAD_BANK(pad) * 0x40 + PAD_PIN(pad) / 8 * 0x10;
> +	/* mA */
> +	if (PAD_MA_VALID(pad)) {
> +		bp = PAD_PIN(pad) % 8 * 4;
> +		bm = 0x3 << bp;
> +		reg = __raw_readl(iomux_base + ofs);
> +		reg &= ~bm;
> +		reg |= PAD_MA(pad)  << bp;
s/  / /
This wasn't here before

I'm not sure if this is worth a v8.

Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 09/15] ARM: mxs: Add clock support
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
                   ` (5 preceding siblings ...)
  2010-12-18 13:39 ` [PATCH v7 08/15] ARM: mxs: Add iomux support Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 13/15] ARM: mxs: Add initial mx23evk support Shawn Guo
  2010-12-18 13:39 ` [PATCH v7 14/15] ARM: mxs: Add initial mx28evk support Shawn Guo
  8 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

Add clock for MXS-based SoCs, MX23 and MX28.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Changes for v7:
 - Remove one tailing tab in clock-mx23.c and clock-mx28.c

Changes for v5
 - Fix PARENT_RATE_SHIFT from left to right

Changes for v3:
 - Fix freq overflow in clock-mx23.c as well
 - Fix the overflow using SH_DIV and shifting 8 bits
 - Remove the inclusion of hardware.h and include mx23.h/mx28.h

Changes for v2:
 - Shift pll0_clock freq 480MHz in children freq computation to avoid overflow
 - Fix fec_clk to stand for fec clock than IEEE1588 time clock
 - Add pll2_clk into clock lookups, as it's fec phy clock and needs to be on before reset phy

 arch/arm/mach-mxs/clock-mx23.c          |  526 ++++++++++++++++++++++
 arch/arm/mach-mxs/clock-mx28.c          |  734 +++++++++++++++++++++++++++++++
 arch/arm/mach-mxs/clock.c               |  200 +++++++++
 arch/arm/mach-mxs/include/mach/clkdev.h |    7 +
 arch/arm/mach-mxs/include/mach/clock.h  |   64 +++
 arch/arm/mach-mxs/regs-clkctrl-mx23.h   |  455 +++++++++++++++++++
 arch/arm/mach-mxs/regs-clkctrl-mx28.h   |  663 ++++++++++++++++++++++++++++
 7 files changed, 2649 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/clock-mx23.c
 create mode 100644 arch/arm/mach-mxs/clock-mx28.c
 create mode 100644 arch/arm/mach-mxs/clock.c
 create mode 100644 arch/arm/mach-mxs/include/mach/clkdev.h
 create mode 100644 arch/arm/mach-mxs/include/mach/clock.h
 create mode 100644 arch/arm/mach-mxs/regs-clkctrl-mx23.h
 create mode 100644 arch/arm/mach-mxs/regs-clkctrl-mx28.h

diff --git a/arch/arm/mach-mxs/clock-mx23.c b/arch/arm/mach-mxs/clock-mx23.c
new file mode 100644
index 0000000..8f5a19a
--- /dev/null
+++ b/arch/arm/mach-mxs/clock-mx23.c
@@ -0,0 +1,526 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/jiffies.h>
+
+#include <asm/clkdev.h>
+#include <asm/div64.h>
+
+#include <mach/mx23.h>
+#include <mach/common.h>
+#include <mach/clock.h>
+
+#include "regs-clkctrl-mx23.h"
+
+#define CLKCTRL_BASE_ADDR	MX23_IO_ADDRESS(MX23_CLKCTRL_BASE_ADDR)
+#define DIGCTRL_BASE_ADDR	MX23_IO_ADDRESS(MX23_DIGCTL_BASE_ADDR)
+
+#define PARENT_RATE_SHIFT	8
+
+static int _raw_clk_enable(struct clk *clk)
+{
+	u32 reg;
+
+	if (clk->enable_reg) {
+		reg = __raw_readl(clk->enable_reg);
+		reg &= ~(1 << clk->enable_shift);
+		__raw_writel(reg, clk->enable_reg);
+	}
+
+	return 0;
+}
+
+static void _raw_clk_disable(struct clk *clk)
+{
+	u32 reg;
+
+	if (clk->enable_reg) {
+		reg = __raw_readl(clk->enable_reg);
+		reg |= 1 << clk->enable_shift;
+		__raw_writel(reg, clk->enable_reg);
+	}
+}
+
+/*
+ * ref_xtal_clk
+ */
+static unsigned long ref_xtal_clk_get_rate(struct clk *clk)
+{
+	return 24000000;
+}
+
+static struct clk ref_xtal_clk = {
+	.get_rate = ref_xtal_clk_get_rate,
+};
+
+/*
+ * pll_clk
+ */
+static unsigned long pll_clk_get_rate(struct clk *clk)
+{
+	return 480000000;
+}
+
+static int pll_clk_enable(struct clk *clk)
+{
+	__raw_writel(BM_CLKCTRL_PLLCTRL0_POWER |
+			BM_CLKCTRL_PLLCTRL0_EN_USB_CLKS,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_PLLCTRL0_SET);
+
+	/* Only a 10us delay is need. PLLCTRL1 LOCK bitfied is only a timer
+	 * and is incorrect (excessive). Per definition of the PLLCTRL0
+	 * POWER field, waiting at least 10us.
+	 */
+	udelay(10);
+
+	return 0;
+}
+
+static void pll_clk_disable(struct clk *clk)
+{
+	__raw_writel(BM_CLKCTRL_PLLCTRL0_POWER |
+			BM_CLKCTRL_PLLCTRL0_EN_USB_CLKS,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_PLLCTRL0_CLR);
+}
+
+static struct clk pll_clk = {
+	 .get_rate = pll_clk_get_rate,
+	 .enable = pll_clk_enable,
+	 .disable = pll_clk_disable,
+	 .parent = &ref_xtal_clk,
+};
+
+/*
+ * ref_clk
+ */
+#define _CLK_GET_RATE_REF(name, sr, ss)					\
+static unsigned long name##_get_rate(struct clk *clk)			\
+{									\
+	unsigned long parent_rate;					\
+	u32 reg, div;							\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##sr);		\
+	div = (reg >> BP_CLKCTRL_##sr##_##ss##FRAC) & 0x3f;		\
+	parent_rate = clk_get_rate(clk->parent);			\
+									\
+	return SH_DIV((parent_rate >> PARENT_RATE_SHIFT) * 18,		\
+			div, PARENT_RATE_SHIFT);			\
+}
+
+_CLK_GET_RATE_REF(ref_cpu_clk, FRAC, CPU)
+_CLK_GET_RATE_REF(ref_emi_clk, FRAC, EMI)
+_CLK_GET_RATE_REF(ref_pix_clk, FRAC, PIX)
+_CLK_GET_RATE_REF(ref_io_clk, FRAC, IO)
+
+#define _DEFINE_CLOCK_REF(name, er, es)					\
+	static struct clk name = {					\
+		.enable_reg	= CLKCTRL_BASE_ADDR + HW_CLKCTRL_##er,	\
+		.enable_shift	= BP_CLKCTRL_##er##_CLKGATE##es,	\
+		.get_rate	= name##_get_rate,			\
+		.enable		= _raw_clk_enable,			\
+		.disable	= _raw_clk_disable,			\
+		.parent		= &pll_clk,				\
+	}
+
+_DEFINE_CLOCK_REF(ref_cpu_clk, FRAC, CPU);
+_DEFINE_CLOCK_REF(ref_emi_clk, FRAC, EMI);
+_DEFINE_CLOCK_REF(ref_pix_clk, FRAC, PIX);
+_DEFINE_CLOCK_REF(ref_io_clk, FRAC, IO);
+
+/*
+ * General clocks
+ *
+ * clk_get_rate
+ */
+static unsigned long rtc_clk_get_rate(struct clk *clk)
+{
+	/* ref_xtal_clk is implemented as the only parent */
+	return clk_get_rate(clk->parent) / 768;
+}
+
+static unsigned long clk32k_clk_get_rate(struct clk *clk)
+{
+	return clk->parent->get_rate(clk->parent) / 750;
+}
+
+#define _CLK_GET_RATE(name, rs)						\
+static unsigned long name##_get_rate(struct clk *clk)			\
+{									\
+	u32 reg, div;							\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs);		\
+									\
+	if (clk->parent == &ref_xtal_clk)				\
+		div = (reg & BM_CLKCTRL_##rs##_DIV_XTAL) >>		\
+			BP_CLKCTRL_##rs##_DIV_XTAL;			\
+	else								\
+		div = (reg & BM_CLKCTRL_##rs##_DIV_##rs) >>		\
+			BP_CLKCTRL_##rs##_DIV_##rs;			\
+									\
+	if (!div)							\
+		return -EINVAL;						\
+									\
+	return clk_get_rate(clk->parent) / div;				\
+}
+
+_CLK_GET_RATE(cpu_clk, CPU)
+_CLK_GET_RATE(emi_clk, EMI)
+
+#define _CLK_GET_RATE1(name, rs)					\
+static unsigned long name##_get_rate(struct clk *clk)			\
+{									\
+	u32 reg, div;							\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs);		\
+	div = (reg & BM_CLKCTRL_##rs##_DIV) >> BP_CLKCTRL_##rs##_DIV;	\
+									\
+	if (!div)							\
+		return -EINVAL;						\
+									\
+	return clk_get_rate(clk->parent) / div;				\
+}
+
+_CLK_GET_RATE1(hbus_clk, HBUS)
+_CLK_GET_RATE1(xbus_clk, XBUS)
+_CLK_GET_RATE1(ssp_clk, SSP)
+_CLK_GET_RATE1(gpmi_clk, GPMI)
+_CLK_GET_RATE1(lcdif_clk, PIX)
+
+#define _CLK_GET_RATE_STUB(name)					\
+static unsigned long name##_get_rate(struct clk *clk)			\
+{									\
+	return clk_get_rate(clk->parent);				\
+}
+
+_CLK_GET_RATE_STUB(uart_clk)
+_CLK_GET_RATE_STUB(audio_clk)
+_CLK_GET_RATE_STUB(pwm_clk)
+
+/*
+ * clk_set_rate
+ */
+static int cpu_clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	u32 reg, bm_busy, div_max, d, f, div, frac;
+	unsigned long diff, parent_rate, calc_rate;
+	int i;
+
+	parent_rate = clk_get_rate(clk->parent);
+
+	if (clk->parent == &ref_xtal_clk) {
+		div_max = BM_CLKCTRL_CPU_DIV_XTAL >> BP_CLKCTRL_CPU_DIV_XTAL;
+		bm_busy = BM_CLKCTRL_CPU_BUSY_REF_XTAL;
+		div = DIV_ROUND_UP(parent_rate, rate);
+		if (div == 0 || div > div_max)
+			return -EINVAL;
+	} else {
+		div_max = BM_CLKCTRL_CPU_DIV_CPU >> BP_CLKCTRL_CPU_DIV_CPU;
+		bm_busy = BM_CLKCTRL_CPU_BUSY_REF_CPU;
+		rate >>= PARENT_RATE_SHIFT;
+		parent_rate >>= PARENT_RATE_SHIFT;
+		diff = parent_rate;
+		div = frac = 1;
+		for (d = 1; d <= div_max; d++) {
+			f = parent_rate * 18 / d / rate;
+			if ((parent_rate * 18 / d) % rate)
+				f++;
+			if (f < 18 || f > 35)
+				continue;
+
+			calc_rate = parent_rate * 18 / f / d;
+			if (calc_rate > rate)
+				continue;
+
+			if (rate - calc_rate < diff) {
+				frac = f;
+				div = d;
+				diff = rate - calc_rate;
+			}
+
+			if (diff == 0)
+				break;
+		}
+
+		if (diff == parent_rate)
+			return -EINVAL;
+
+		reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_FRAC);
+		reg &= ~BM_CLKCTRL_FRAC_CPUFRAC;
+		reg |= frac;
+		__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_FRAC);
+	}
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU);
+	reg &= ~BM_CLKCTRL_CPU_DIV_CPU;
+	reg |= div << BP_CLKCTRL_CPU_DIV_CPU;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU);
+
+	for (i = 10000; i; i--)
+		if (!(__raw_readl(CLKCTRL_BASE_ADDR +
+					HW_CLKCTRL_CPU) & bm_busy))
+			break;
+	if (!i)	{
+		pr_err("%s: divider writing timeout\n", __func__);
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+#define _CLK_SET_RATE(name, dr)						\
+static int name##_set_rate(struct clk *clk, unsigned long rate)		\
+{									\
+	u32 reg, div_max, div;						\
+	unsigned long parent_rate;					\
+	int i;								\
+									\
+	parent_rate = clk_get_rate(clk->parent);			\
+	div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV;	\
+									\
+	div = DIV_ROUND_UP(parent_rate, rate);				\
+	if (div == 0 || div > div_max)					\
+		return -EINVAL;						\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr);		\
+	reg &= ~BM_CLKCTRL_##dr##_DIV;					\
+	reg |= div << BP_CLKCTRL_##dr##_DIV;				\
+	if (reg | (1 << clk->enable_shift)) {				\
+		pr_err("%s: clock is gated\n", __func__);		\
+		return -EINVAL;						\
+	}								\
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr);		\
+									\
+	for (i = 10000; i; i--)						\
+		if (!(__raw_readl(CLKCTRL_BASE_ADDR +			\
+			HW_CLKCTRL_##dr) & BM_CLKCTRL_##dr##_BUSY))	\
+			break;						\
+	if (!i)	{							\
+		pr_err("%s: divider writing timeout\n", __func__);	\
+		return -ETIMEDOUT;					\
+	}								\
+									\
+	return 0;							\
+}
+
+_CLK_SET_RATE(xbus_clk, XBUS)
+_CLK_SET_RATE(ssp_clk, SSP)
+_CLK_SET_RATE(gpmi_clk, GPMI)
+_CLK_SET_RATE(lcdif_clk, PIX)
+
+#define _CLK_SET_RATE_STUB(name)					\
+static int name##_set_rate(struct clk *clk, unsigned long rate)		\
+{									\
+	return -EINVAL;							\
+}
+
+_CLK_SET_RATE_STUB(emi_clk)
+_CLK_SET_RATE_STUB(uart_clk)
+_CLK_SET_RATE_STUB(audio_clk)
+_CLK_SET_RATE_STUB(pwm_clk)
+_CLK_SET_RATE_STUB(clk32k_clk)
+
+/*
+ * clk_set_parent
+ */
+#define _CLK_SET_PARENT(name, bit)					\
+static int name##_set_parent(struct clk *clk, struct clk *parent)	\
+{									\
+	if (parent != clk->parent) {					\
+		__raw_writel(BM_CLKCTRL_CLKSEQ_BYPASS_##bit,		\
+			 HW_CLKCTRL_CLKSEQ_TOG);			\
+		clk->parent = parent;					\
+	}								\
+									\
+	return 0;							\
+}
+
+_CLK_SET_PARENT(cpu_clk, CPU)
+_CLK_SET_PARENT(emi_clk, EMI)
+_CLK_SET_PARENT(ssp_clk, SSP)
+_CLK_SET_PARENT(gpmi_clk, GPMI)
+_CLK_SET_PARENT(lcdif_clk, PIX)
+
+#define _CLK_SET_PARENT_STUB(name)					\
+static int name##_set_parent(struct clk *clk, struct clk *parent)	\
+{									\
+	if (parent != clk->parent)					\
+		return -EINVAL;						\
+	else								\
+		return 0;						\
+}
+
+_CLK_SET_PARENT_STUB(uart_clk)
+_CLK_SET_PARENT_STUB(audio_clk)
+_CLK_SET_PARENT_STUB(pwm_clk)
+_CLK_SET_PARENT_STUB(clk32k_clk)
+
+/*
+ * clk definition
+ */
+static struct clk cpu_clk = {
+	.get_rate = cpu_clk_get_rate,
+	.set_rate = cpu_clk_set_rate,
+	.set_parent = cpu_clk_set_parent,
+	.parent = &ref_cpu_clk,
+};
+
+static struct clk hbus_clk = {
+	.get_rate = hbus_clk_get_rate,
+	.parent = &cpu_clk,
+};
+
+static struct clk xbus_clk = {
+	.get_rate = xbus_clk_get_rate,
+	.set_rate = xbus_clk_set_rate,
+	.parent = &ref_xtal_clk,
+};
+
+static struct clk rtc_clk = {
+	.get_rate = rtc_clk_get_rate,
+	.parent = &ref_xtal_clk,
+};
+
+/* usb_clk gate is controlled in DIGCTRL other than CLKCTRL */
+static struct clk usb_clk = {
+	.enable_reg = DIGCTRL_BASE_ADDR,
+	.enable_shift = 2,
+	.enable = _raw_clk_enable,
+	.disable = _raw_clk_disable,
+	.parent = &pll_clk,
+};
+
+#define _DEFINE_CLOCK(name, er, es, p)					\
+	static struct clk name = {					\
+		.enable_reg	= CLKCTRL_BASE_ADDR + HW_CLKCTRL_##er,	\
+		.enable_shift	= BP_CLKCTRL_##er##_##es,		\
+		.get_rate	= name##_get_rate,			\
+		.set_rate	= name##_set_rate,			\
+		.set_parent	= name##_set_parent,			\
+		.enable		= _raw_clk_enable,			\
+		.disable	= _raw_clk_disable,			\
+		.parent		= p,					\
+	}
+
+_DEFINE_CLOCK(emi_clk, EMI, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(ssp_clk, SSP, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(gpmi_clk, GPMI, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(lcdif_clk, PIX, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(uart_clk, XTAL, UART_CLK_GATE, &ref_xtal_clk);
+_DEFINE_CLOCK(audio_clk, XTAL, FILT_CLK24M_GATE, &ref_xtal_clk);
+_DEFINE_CLOCK(pwm_clk, XTAL, PWM_CLK24M_GATE, &ref_xtal_clk);
+_DEFINE_CLOCK(clk32k_clk, XTAL, TIMROT_CLK32K_GATE, &ref_xtal_clk);
+
+#define _REGISTER_CLOCK(d, n, c) \
+	{ \
+		.dev_id = d, \
+		.con_id = n, \
+		.clk = &c, \
+	},
+
+static struct clk_lookup lookups[] = {
+	_REGISTER_CLOCK("mxs-duart.0", NULL, uart_clk)
+	_REGISTER_CLOCK("rtc", NULL, rtc_clk)
+	_REGISTER_CLOCK(NULL, "hclk", hbus_clk)
+	_REGISTER_CLOCK(NULL, "xclk", xbus_clk)
+	_REGISTER_CLOCK(NULL, "usb", usb_clk)
+	_REGISTER_CLOCK(NULL, "audio", audio_clk)
+	_REGISTER_CLOCK(NULL, "pwm", pwm_clk)
+};
+
+static int clk_misc_init(void)
+{
+	u32 reg;
+	int i;
+
+	/* Fix up parent per register setting */
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_CLKSEQ);
+	cpu_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_CPU) ?
+			&ref_xtal_clk : &ref_cpu_clk;
+	emi_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_EMI) ?
+			&ref_xtal_clk : &ref_emi_clk;
+	ssp_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_SSP) ?
+			&ref_xtal_clk : &ref_io_clk;
+	gpmi_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_GPMI) ?
+			&ref_xtal_clk : &ref_io_clk;
+	lcdif_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_PIX) ?
+			&ref_xtal_clk : &ref_pix_clk;
+
+	/* Use int div over frac when both are available */
+	__raw_writel(BM_CLKCTRL_CPU_DIV_XTAL_FRAC_EN,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU_CLR);
+	__raw_writel(BM_CLKCTRL_CPU_DIV_CPU_FRAC_EN,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU_CLR);
+	__raw_writel(BM_CLKCTRL_HBUS_DIV_FRAC_EN,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS_CLR);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_XBUS);
+	reg &= ~BM_CLKCTRL_XBUS_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_XBUS);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP);
+	reg &= ~BM_CLKCTRL_SSP_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_GPMI);
+	reg &= ~BM_CLKCTRL_GPMI_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_GPMI);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_PIX);
+	reg &= ~BM_CLKCTRL_PIX_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_PIX);
+
+	/*
+	 * Set safe hbus clock divider. A divider of 3 ensure that
+	 * the Vddd voltage required for the cpu clock is sufficiently
+	 * high for the hbus clock.
+	 */
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS);
+	reg &= BM_CLKCTRL_HBUS_DIV;
+	reg |= 3 << BP_CLKCTRL_HBUS_DIV;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS);
+
+	for (i = 10000; i; i--)
+		if (!(__raw_readl(CLKCTRL_BASE_ADDR +
+			HW_CLKCTRL_HBUS) & BM_CLKCTRL_HBUS_BUSY))
+			break;
+	if (!i) {
+		pr_err("%s: divider writing timeout\n", __func__);
+		return -ETIMEDOUT;
+	}
+
+	/* Gate off cpu clock in WFI for power saving */
+	__raw_writel(BM_CLKCTRL_CPU_INTERRUPT_WAIT,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU_SET);
+
+	return 0;
+}
+
+int __init mx23_clocks_init(void)
+{
+	clk_misc_init();
+
+	clkdev_add_table(lookups, ARRAY_SIZE(lookups));
+
+	mxs_timer_init(&clk32k_clk, MX23_INT_TIMER0);
+
+	return 0;
+}
diff --git a/arch/arm/mach-mxs/clock-mx28.c b/arch/arm/mach-mxs/clock-mx28.c
new file mode 100644
index 0000000..74e2103
--- /dev/null
+++ b/arch/arm/mach-mxs/clock-mx28.c
@@ -0,0 +1,734 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/jiffies.h>
+
+#include <asm/clkdev.h>
+#include <asm/div64.h>
+
+#include <mach/mx28.h>
+#include <mach/common.h>
+#include <mach/clock.h>
+
+#include "regs-clkctrl-mx28.h"
+
+#define CLKCTRL_BASE_ADDR	MX28_IO_ADDRESS(MX28_CLKCTRL_BASE_ADDR)
+#define DIGCTRL_BASE_ADDR	MX28_IO_ADDRESS(MX28_DIGCTL_BASE_ADDR)
+
+#define PARENT_RATE_SHIFT	8
+
+static struct clk pll2_clk;
+static struct clk cpu_clk;
+static struct clk emi_clk;
+static struct clk saif0_clk;
+static struct clk saif1_clk;
+static struct clk clk32k_clk;
+
+static int _raw_clk_enable(struct clk *clk)
+{
+	u32 reg;
+
+	if (clk->enable_reg) {
+		reg = __raw_readl(clk->enable_reg);
+		reg &= ~(1 << clk->enable_shift);
+		__raw_writel(reg, clk->enable_reg);
+	}
+
+	return 0;
+}
+
+static void _raw_clk_disable(struct clk *clk)
+{
+	u32 reg;
+
+	if (clk->enable_reg) {
+		reg = __raw_readl(clk->enable_reg);
+		reg |= 1 << clk->enable_shift;
+		__raw_writel(reg, clk->enable_reg);
+	}
+}
+
+/*
+ * ref_xtal_clk
+ */
+static unsigned long ref_xtal_clk_get_rate(struct clk *clk)
+{
+	return 24000000;
+}
+
+static struct clk ref_xtal_clk = {
+	.get_rate = ref_xtal_clk_get_rate,
+};
+
+/*
+ * pll_clk
+ */
+static unsigned long pll0_clk_get_rate(struct clk *clk)
+{
+	return 480000000;
+}
+
+static unsigned long pll1_clk_get_rate(struct clk *clk)
+{
+	return 480000000;
+}
+
+static unsigned long pll2_clk_get_rate(struct clk *clk)
+{
+	return 50000000;
+}
+
+#define _CLK_ENABLE_PLL(name, r, g)					\
+static int name##_enable(struct clk *clk)				\
+{									\
+	__raw_writel(BM_CLKCTRL_##r##CTRL0_POWER,			\
+		     CLKCTRL_BASE_ADDR + HW_CLKCTRL_##r##CTRL0_SET);	\
+	udelay(10);							\
+									\
+	if (clk == &pll2_clk)						\
+		__raw_writel(BM_CLKCTRL_##r##CTRL0_##g,			\
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_##r##CTRL0_CLR);	\
+	else								\
+		__raw_writel(BM_CLKCTRL_##r##CTRL0_##g,			\
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_##r##CTRL0_SET);	\
+									\
+	return 0;							\
+}
+
+_CLK_ENABLE_PLL(pll0_clk, PLL0, EN_USB_CLKS)
+_CLK_ENABLE_PLL(pll1_clk, PLL1, EN_USB_CLKS)
+_CLK_ENABLE_PLL(pll2_clk, PLL2, CLKGATE)
+
+#define _CLK_DISABLE_PLL(name, r, g)					\
+static void name##_disable(struct clk *clk)				\
+{									\
+	__raw_writel(BM_CLKCTRL_##r##CTRL0_POWER,			\
+		     CLKCTRL_BASE_ADDR + HW_CLKCTRL_##r##CTRL0_CLR);	\
+									\
+	if (clk == &pll2_clk)						\
+		__raw_writel(BM_CLKCTRL_##r##CTRL0_##g,			\
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_##r##CTRL0_SET);	\
+	else								\
+		__raw_writel(BM_CLKCTRL_##r##CTRL0_##g,			\
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_##r##CTRL0_CLR);	\
+									\
+}
+
+_CLK_DISABLE_PLL(pll0_clk, PLL0, EN_USB_CLKS)
+_CLK_DISABLE_PLL(pll1_clk, PLL1, EN_USB_CLKS)
+_CLK_DISABLE_PLL(pll2_clk, PLL2, CLKGATE)
+
+#define _DEFINE_CLOCK_PLL(name)						\
+	static struct clk name = {					\
+		.get_rate	= name##_get_rate,			\
+		.enable		= name##_enable,			\
+		.disable	= name##_disable,			\
+		.parent		= &ref_xtal_clk,			\
+	}
+
+_DEFINE_CLOCK_PLL(pll0_clk);
+_DEFINE_CLOCK_PLL(pll1_clk);
+_DEFINE_CLOCK_PLL(pll2_clk);
+
+/*
+ * ref_clk
+ */
+#define _CLK_GET_RATE_REF(name, sr, ss)					\
+static unsigned long name##_get_rate(struct clk *clk)			\
+{									\
+	unsigned long parent_rate;					\
+	u32 reg, div;							\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##sr);		\
+	div = (reg >> BP_CLKCTRL_##sr##_##ss##FRAC) & 0x3f;		\
+	parent_rate = clk_get_rate(clk->parent);			\
+									\
+	return SH_DIV((parent_rate >> PARENT_RATE_SHIFT) * 18,		\
+			div, PARENT_RATE_SHIFT);			\
+}
+
+_CLK_GET_RATE_REF(ref_cpu_clk, FRAC0, CPU)
+_CLK_GET_RATE_REF(ref_emi_clk, FRAC0, EMI)
+_CLK_GET_RATE_REF(ref_io0_clk, FRAC0, IO0)
+_CLK_GET_RATE_REF(ref_io1_clk, FRAC0, IO1)
+_CLK_GET_RATE_REF(ref_pix_clk, FRAC1, PIX)
+_CLK_GET_RATE_REF(ref_gpmi_clk, FRAC1, GPMI)
+
+#define _DEFINE_CLOCK_REF(name, er, es)					\
+	static struct clk name = {					\
+		.enable_reg	= CLKCTRL_BASE_ADDR + HW_CLKCTRL_##er,	\
+		.enable_shift	= BP_CLKCTRL_##er##_CLKGATE##es,	\
+		.get_rate	= name##_get_rate,			\
+		.enable		= _raw_clk_enable,			\
+		.disable	= _raw_clk_disable,			\
+		.parent		= &pll0_clk,				\
+	}
+
+_DEFINE_CLOCK_REF(ref_cpu_clk, FRAC0, CPU);
+_DEFINE_CLOCK_REF(ref_emi_clk, FRAC0, EMI);
+_DEFINE_CLOCK_REF(ref_io0_clk, FRAC0, IO0);
+_DEFINE_CLOCK_REF(ref_io1_clk, FRAC0, IO1);
+_DEFINE_CLOCK_REF(ref_pix_clk, FRAC1, PIX);
+_DEFINE_CLOCK_REF(ref_gpmi_clk, FRAC1, GPMI);
+
+/*
+ * General clocks
+ *
+ * clk_get_rate
+ */
+static unsigned long lradc_clk_get_rate(struct clk *clk)
+{
+	return clk_get_rate(clk->parent) / 16;
+}
+
+static unsigned long rtc_clk_get_rate(struct clk *clk)
+{
+	/* ref_xtal_clk is implemented as the only parent */
+	return clk_get_rate(clk->parent) / 768;
+}
+
+static unsigned long clk32k_clk_get_rate(struct clk *clk)
+{
+	return clk->parent->get_rate(clk->parent) / 750;
+}
+
+static unsigned long spdif_clk_get_rate(struct clk *clk)
+{
+	return clk_get_rate(clk->parent) / 4;
+}
+
+#define _CLK_GET_RATE(name, rs)						\
+static unsigned long name##_get_rate(struct clk *clk)			\
+{									\
+	u32 reg, div;							\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs);		\
+									\
+	if (clk->parent == &ref_xtal_clk)				\
+		div = (reg & BM_CLKCTRL_##rs##_DIV_XTAL) >>		\
+			BP_CLKCTRL_##rs##_DIV_XTAL;			\
+	else								\
+		div = (reg & BM_CLKCTRL_##rs##_DIV_##rs) >>		\
+			BP_CLKCTRL_##rs##_DIV_##rs;			\
+									\
+	if (!div)							\
+		return -EINVAL;						\
+									\
+	return clk_get_rate(clk->parent) / div;				\
+}
+
+_CLK_GET_RATE(cpu_clk, CPU)
+_CLK_GET_RATE(emi_clk, EMI)
+
+#define _CLK_GET_RATE1(name, rs)					\
+static unsigned long name##_get_rate(struct clk *clk)			\
+{									\
+	u32 reg, div;							\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs);		\
+	div = (reg & BM_CLKCTRL_##rs##_DIV) >> BP_CLKCTRL_##rs##_DIV;	\
+									\
+	if (!div)							\
+		return -EINVAL;						\
+									\
+	if (clk == &saif0_clk || clk == &saif1_clk)			\
+		return clk_get_rate(clk->parent) >> 16 * div;		\
+	else								\
+		return clk_get_rate(clk->parent) / div;			\
+}
+
+_CLK_GET_RATE1(hbus_clk, HBUS)
+_CLK_GET_RATE1(xbus_clk, XBUS)
+_CLK_GET_RATE1(ssp0_clk, SSP0)
+_CLK_GET_RATE1(ssp1_clk, SSP1)
+_CLK_GET_RATE1(ssp2_clk, SSP2)
+_CLK_GET_RATE1(ssp3_clk, SSP3)
+_CLK_GET_RATE1(gpmi_clk, GPMI)
+_CLK_GET_RATE1(lcdif_clk, DIS_LCDIF)
+_CLK_GET_RATE1(saif0_clk, SAIF0)
+_CLK_GET_RATE1(saif1_clk, SAIF1)
+
+#define _CLK_GET_RATE_STUB(name)					\
+static unsigned long name##_get_rate(struct clk *clk)			\
+{									\
+	return clk_get_rate(clk->parent);				\
+}
+
+_CLK_GET_RATE_STUB(uart_clk)
+_CLK_GET_RATE_STUB(pwm_clk)
+_CLK_GET_RATE_STUB(can0_clk)
+_CLK_GET_RATE_STUB(can1_clk)
+_CLK_GET_RATE_STUB(fec_clk)
+
+/*
+ * clk_set_rate
+ */
+/* fool compiler */
+#define BM_CLKCTRL_CPU_DIV	0
+#define BP_CLKCTRL_CPU_DIV	0
+#define BM_CLKCTRL_CPU_BUSY	0
+
+#define _CLK_SET_RATE(name, dr, fr, fs)					\
+static int name##_set_rate(struct clk *clk, unsigned long rate)		\
+{									\
+	u32 reg, bm_busy, div_max, d, f, div, frac;			\
+	unsigned long diff, parent_rate, calc_rate;			\
+	int i;								\
+									\
+	parent_rate = clk_get_rate(clk->parent);			\
+	div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV;	\
+	bm_busy = BM_CLKCTRL_##dr##_BUSY;				\
+									\
+	if (clk->parent == &ref_xtal_clk) {				\
+		div = DIV_ROUND_UP(parent_rate, rate);			\
+		if (clk == &cpu_clk) {					\
+			div_max = BM_CLKCTRL_CPU_DIV_XTAL >>		\
+				BP_CLKCTRL_CPU_DIV_XTAL;		\
+			bm_busy = BM_CLKCTRL_CPU_BUSY_REF_XTAL;		\
+		}							\
+		if (div == 0 || div > div_max)				\
+			return -EINVAL;					\
+	} else {							\
+		rate >>= PARENT_RATE_SHIFT;				\
+		parent_rate >>= PARENT_RATE_SHIFT;			\
+		diff = parent_rate;					\
+		div = frac = 1;						\
+		if (clk == &cpu_clk) {					\
+			div_max = BM_CLKCTRL_CPU_DIV_CPU >>		\
+				BP_CLKCTRL_CPU_DIV_CPU;			\
+			bm_busy = BM_CLKCTRL_CPU_BUSY_REF_CPU;		\
+		}							\
+		for (d = 1; d <= div_max; d++) {			\
+			f = parent_rate * 18 / d / rate;		\
+			if ((parent_rate * 18 / d) % rate)		\
+				f++;					\
+			if (f < 18 || f > 35)				\
+				continue;				\
+									\
+			calc_rate = parent_rate * 18 / f / d;		\
+			if (calc_rate > rate)				\
+				continue;				\
+									\
+			if (rate - calc_rate < diff) {			\
+				frac = f;				\
+				div = d;				\
+				diff = rate - calc_rate;		\
+			}						\
+									\
+			if (diff == 0)					\
+				break;					\
+		}							\
+									\
+		if (diff == parent_rate)				\
+			return -EINVAL;					\
+									\
+		reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##fr);	\
+		reg &= ~BM_CLKCTRL_##fr##_##fs##FRAC;			\
+		reg |= frac;						\
+		__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##fr);	\
+	}								\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr);		\
+	if (clk == &cpu_clk) {						\
+		reg &= ~BM_CLKCTRL_CPU_DIV_CPU;				\
+		reg |= div << BP_CLKCTRL_CPU_DIV_CPU;			\
+	} else {							\
+		reg &= ~BM_CLKCTRL_##dr##_DIV;				\
+		reg |= div << BP_CLKCTRL_##dr##_DIV;			\
+		if (reg | (1 << clk->enable_shift)) {			\
+			pr_err("%s: clock is gated\n", __func__);	\
+			return -EINVAL;					\
+		}							\
+	}								\
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU);		\
+									\
+	for (i = 10000; i; i--)						\
+		if (!(__raw_readl(CLKCTRL_BASE_ADDR +			\
+			HW_CLKCTRL_##dr) & bm_busy))			\
+			break;						\
+	if (!i)	{							\
+		pr_err("%s: divider writing timeout\n", __func__);	\
+		return -ETIMEDOUT;					\
+	}								\
+									\
+	return 0;							\
+}
+
+_CLK_SET_RATE(cpu_clk, CPU, FRAC0, CPU)
+_CLK_SET_RATE(ssp0_clk, SSP0, FRAC0, IO0)
+_CLK_SET_RATE(ssp1_clk, SSP1, FRAC0, IO0)
+_CLK_SET_RATE(ssp2_clk, SSP2, FRAC0, IO1)
+_CLK_SET_RATE(ssp3_clk, SSP3, FRAC0, IO1)
+_CLK_SET_RATE(lcdif_clk, DIS_LCDIF, FRAC1, PIX)
+_CLK_SET_RATE(gpmi_clk, GPMI, FRAC1, GPMI)
+
+#define _CLK_SET_RATE1(name, dr)					\
+static int name##_set_rate(struct clk *clk, unsigned long rate)		\
+{									\
+	u32 reg, div_max, div;						\
+	unsigned long parent_rate;					\
+	int i;								\
+									\
+	parent_rate = clk_get_rate(clk->parent);			\
+	div_max = BM_CLKCTRL_##dr##_DIV >> BP_CLKCTRL_##dr##_DIV;	\
+									\
+	div = DIV_ROUND_UP(parent_rate, rate);				\
+	if (div == 0 || div > div_max)					\
+		return -EINVAL;						\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr);		\
+	reg &= ~BM_CLKCTRL_##dr##_DIV;					\
+	reg |= div << BP_CLKCTRL_##dr##_DIV;				\
+	if (reg | (1 << clk->enable_shift)) {				\
+		pr_err("%s: clock is gated\n", __func__);		\
+		return -EINVAL;						\
+	}								\
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr);		\
+									\
+	for (i = 10000; i; i--)						\
+		if (!(__raw_readl(CLKCTRL_BASE_ADDR +			\
+			HW_CLKCTRL_##dr) & BM_CLKCTRL_##dr##_BUSY))	\
+			break;						\
+	if (!i)	{							\
+		pr_err("%s: divider writing timeout\n", __func__);	\
+		return -ETIMEDOUT;					\
+	}								\
+									\
+	return 0;							\
+}
+
+_CLK_SET_RATE1(xbus_clk, XBUS)
+
+/* saif clock uses 16 bits frac div */
+#define _CLK_SET_RATE_SAIF(name, rs)					\
+static int name##_set_rate(struct clk *clk, unsigned long rate)		\
+{									\
+	u16 div;							\
+	u32 reg;							\
+	u64 lrate;							\
+	unsigned long parent_rate;					\
+	int i;								\
+									\
+	parent_rate = clk_get_rate(clk->parent);			\
+	if (rate > parent_rate)						\
+		return -EINVAL;						\
+									\
+	lrate = (u64)rate << 16;					\
+	do_div(lrate, parent_rate);					\
+	div = (u16)lrate;						\
+									\
+	if (!div)							\
+		return -EINVAL;						\
+									\
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs);		\
+	reg &= ~BM_CLKCTRL_##rs##_DIV;					\
+	reg |= div << BP_CLKCTRL_##rs##_DIV;				\
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_##rs);		\
+									\
+	for (i = 10000; i; i--)						\
+		if (!(__raw_readl(CLKCTRL_BASE_ADDR +			\
+			HW_CLKCTRL_##rs) & BM_CLKCTRL_##rs##_BUSY))	\
+			break;						\
+	if (!i) {							\
+		pr_err("%s: divider writing timeout\n", __func__);	\
+		return -ETIMEDOUT;					\
+	}								\
+									\
+	return 0;							\
+}
+
+_CLK_SET_RATE_SAIF(saif0_clk, SAIF0)
+_CLK_SET_RATE_SAIF(saif1_clk, SAIF1)
+
+#define _CLK_SET_RATE_STUB(name)					\
+static int name##_set_rate(struct clk *clk, unsigned long rate)		\
+{									\
+	return -EINVAL;							\
+}
+
+_CLK_SET_RATE_STUB(emi_clk)
+_CLK_SET_RATE_STUB(uart_clk)
+_CLK_SET_RATE_STUB(pwm_clk)
+_CLK_SET_RATE_STUB(spdif_clk)
+_CLK_SET_RATE_STUB(clk32k_clk)
+_CLK_SET_RATE_STUB(can0_clk)
+_CLK_SET_RATE_STUB(can1_clk)
+_CLK_SET_RATE_STUB(fec_clk)
+
+/*
+ * clk_set_parent
+ */
+#define _CLK_SET_PARENT(name, bit)					\
+static int name##_set_parent(struct clk *clk, struct clk *parent)	\
+{									\
+	if (parent != clk->parent) {					\
+		__raw_writel(BM_CLKCTRL_CLKSEQ_BYPASS_##bit,		\
+			 HW_CLKCTRL_CLKSEQ_TOG);			\
+		clk->parent = parent;					\
+	}								\
+									\
+	return 0;							\
+}
+
+_CLK_SET_PARENT(cpu_clk, CPU)
+_CLK_SET_PARENT(emi_clk, EMI)
+_CLK_SET_PARENT(ssp0_clk, SSP0)
+_CLK_SET_PARENT(ssp1_clk, SSP1)
+_CLK_SET_PARENT(ssp2_clk, SSP2)
+_CLK_SET_PARENT(ssp3_clk, SSP3)
+_CLK_SET_PARENT(lcdif_clk, DIS_LCDIF)
+_CLK_SET_PARENT(gpmi_clk, GPMI)
+_CLK_SET_PARENT(saif0_clk, SAIF0)
+_CLK_SET_PARENT(saif1_clk, SAIF1)
+
+#define _CLK_SET_PARENT_STUB(name)					\
+static int name##_set_parent(struct clk *clk, struct clk *parent)	\
+{									\
+	if (parent != clk->parent)					\
+		return -EINVAL;						\
+	else								\
+		return 0;						\
+}
+
+_CLK_SET_PARENT_STUB(pwm_clk)
+_CLK_SET_PARENT_STUB(uart_clk)
+_CLK_SET_PARENT_STUB(clk32k_clk)
+_CLK_SET_PARENT_STUB(spdif_clk)
+_CLK_SET_PARENT_STUB(fec_clk)
+_CLK_SET_PARENT_STUB(can0_clk)
+_CLK_SET_PARENT_STUB(can1_clk)
+
+/*
+ * clk definition
+ */
+static struct clk cpu_clk = {
+	.get_rate = cpu_clk_get_rate,
+	.set_rate = cpu_clk_set_rate,
+	.set_parent = cpu_clk_set_parent,
+	.parent = &ref_cpu_clk,
+};
+
+static struct clk hbus_clk = {
+	.get_rate = hbus_clk_get_rate,
+	.parent = &cpu_clk,
+};
+
+static struct clk xbus_clk = {
+	.get_rate = xbus_clk_get_rate,
+	.set_rate = xbus_clk_set_rate,
+	.parent = &ref_xtal_clk,
+};
+
+static struct clk lradc_clk = {
+	.get_rate = lradc_clk_get_rate,
+	.parent = &clk32k_clk,
+};
+
+static struct clk rtc_clk = {
+	.get_rate = rtc_clk_get_rate,
+	.parent = &ref_xtal_clk,
+};
+
+/* usb_clk gate is controlled in DIGCTRL other than CLKCTRL */
+static struct clk usb0_clk = {
+	.enable_reg = DIGCTRL_BASE_ADDR,
+	.enable_shift = 2,
+	.enable = _raw_clk_enable,
+	.disable = _raw_clk_disable,
+	.parent = &pll0_clk,
+};
+
+static struct clk usb1_clk = {
+	.enable_reg = DIGCTRL_BASE_ADDR,
+	.enable_shift = 16,
+	.enable = _raw_clk_enable,
+	.disable = _raw_clk_disable,
+	.parent = &pll1_clk,
+};
+
+#define _DEFINE_CLOCK(name, er, es, p)					\
+	static struct clk name = {					\
+		.enable_reg	= CLKCTRL_BASE_ADDR + HW_CLKCTRL_##er,	\
+		.enable_shift	= BP_CLKCTRL_##er##_##es,		\
+		.get_rate	= name##_get_rate,			\
+		.set_rate	= name##_set_rate,			\
+		.set_parent	= name##_set_parent,			\
+		.enable		= _raw_clk_enable,			\
+		.disable	= _raw_clk_disable,			\
+		.parent		= p,					\
+	}
+
+_DEFINE_CLOCK(emi_clk, EMI, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(ssp0_clk, SSP0, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(ssp1_clk, SSP1, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(ssp2_clk, SSP2, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(ssp3_clk, SSP3, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(lcdif_clk, DIS_LCDIF, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(gpmi_clk, GPMI, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(saif0_clk, SAIF0, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(saif1_clk, SAIF1, CLKGATE, &ref_xtal_clk);
+_DEFINE_CLOCK(can0_clk, FLEXCAN, STOP_CAN0, &ref_xtal_clk);
+_DEFINE_CLOCK(can1_clk, FLEXCAN, STOP_CAN1, &ref_xtal_clk);
+_DEFINE_CLOCK(pwm_clk, XTAL, PWM_CLK24M_GATE, &ref_xtal_clk);
+_DEFINE_CLOCK(uart_clk, XTAL, UART_CLK_GATE, &ref_xtal_clk);
+_DEFINE_CLOCK(clk32k_clk, XTAL, TIMROT_CLK32K_GATE, &ref_xtal_clk);
+_DEFINE_CLOCK(spdif_clk, SPDIF, CLKGATE, &pll0_clk);
+_DEFINE_CLOCK(fec_clk, ENET, DISABLE, &hbus_clk);
+
+#define _REGISTER_CLOCK(d, n, c) \
+	{ \
+		.dev_id = d, \
+		.con_id = n, \
+		.clk = &c, \
+	},
+
+static struct clk_lookup lookups[] = {
+	_REGISTER_CLOCK("mxs-duart.0", NULL, uart_clk)
+	_REGISTER_CLOCK("fec.0", NULL, fec_clk)
+	_REGISTER_CLOCK("rtc", NULL, rtc_clk)
+	_REGISTER_CLOCK("pll2", NULL, pll2_clk)
+	_REGISTER_CLOCK(NULL, "hclk", hbus_clk)
+	_REGISTER_CLOCK(NULL, "xclk", xbus_clk)
+	_REGISTER_CLOCK(NULL, "can0", can0_clk)
+	_REGISTER_CLOCK(NULL, "can1", can1_clk)
+	_REGISTER_CLOCK(NULL, "usb0", usb0_clk)
+	_REGISTER_CLOCK(NULL, "usb1", usb1_clk)
+	_REGISTER_CLOCK(NULL, "pwm", pwm_clk)
+	_REGISTER_CLOCK(NULL, "lradc", lradc_clk)
+	_REGISTER_CLOCK(NULL, "spdif", spdif_clk)
+};
+
+static int clk_misc_init(void)
+{
+	u32 reg;
+	int i;
+
+	/* Fix up parent per register setting */
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_CLKSEQ);
+	cpu_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_CPU) ?
+			&ref_xtal_clk : &ref_cpu_clk;
+	emi_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_EMI) ?
+			&ref_xtal_clk : &ref_emi_clk;
+	ssp0_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_SSP0) ?
+			&ref_xtal_clk : &ref_io0_clk;
+	ssp1_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_SSP1) ?
+			&ref_xtal_clk : &ref_io0_clk;
+	ssp2_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_SSP2) ?
+			&ref_xtal_clk : &ref_io1_clk;
+	ssp3_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_SSP3) ?
+			&ref_xtal_clk : &ref_io1_clk;
+	lcdif_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_DIS_LCDIF) ?
+			&ref_xtal_clk : &ref_pix_clk;
+	gpmi_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_GPMI) ?
+			&ref_xtal_clk : &ref_gpmi_clk;
+	saif0_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_SAIF0) ?
+			&ref_xtal_clk : &pll0_clk;
+	saif1_clk.parent = (reg & BM_CLKCTRL_CLKSEQ_BYPASS_SAIF1) ?
+			&ref_xtal_clk : &pll0_clk;
+
+	/* Use int div over frac when both are available */
+	__raw_writel(BM_CLKCTRL_CPU_DIV_XTAL_FRAC_EN,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU_CLR);
+	__raw_writel(BM_CLKCTRL_CPU_DIV_CPU_FRAC_EN,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU_CLR);
+	__raw_writel(BM_CLKCTRL_HBUS_DIV_FRAC_EN,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS_CLR);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_XBUS);
+	reg &= ~BM_CLKCTRL_XBUS_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_XBUS);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP0);
+	reg &= ~BM_CLKCTRL_SSP0_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP0);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP1);
+	reg &= ~BM_CLKCTRL_SSP1_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP1);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP2);
+	reg &= ~BM_CLKCTRL_SSP2_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP2);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP3);
+	reg &= ~BM_CLKCTRL_SSP3_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_SSP3);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_GPMI);
+	reg &= ~BM_CLKCTRL_GPMI_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_GPMI);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_DIS_LCDIF);
+	reg &= ~BM_CLKCTRL_DIS_LCDIF_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_DIS_LCDIF);
+
+	/* SAIF has to use frac div for functional operation */
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_SAIF0);
+	reg &= ~BM_CLKCTRL_SAIF0_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_SAIF0);
+
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_SAIF1);
+	reg &= ~BM_CLKCTRL_SAIF1_DIV_FRAC_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_SAIF1);
+
+	/*
+	 * Set safe hbus clock divider. A divider of 3 ensure that
+	 * the Vddd voltage required for the cpu clock is sufficiently
+	 * high for the hbus clock.
+	 */
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS);
+	reg &= BM_CLKCTRL_HBUS_DIV;
+	reg |= 3 << BP_CLKCTRL_HBUS_DIV;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_HBUS);
+
+	for (i = 10000; i; i--)
+		if (!(__raw_readl(CLKCTRL_BASE_ADDR +
+			HW_CLKCTRL_HBUS) & BM_CLKCTRL_HBUS_ASM_BUSY))
+			break;
+	if (!i) {
+		pr_err("%s: divider writing timeout\n", __func__);
+		return -ETIMEDOUT;
+	}
+
+	/* Gate off cpu clock in WFI for power saving */
+	__raw_writel(BM_CLKCTRL_CPU_INTERRUPT_WAIT,
+			CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU_SET);
+
+	/* Extra fec clock setting */
+	reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
+	reg &= ~BM_CLKCTRL_ENET_SLEEP;
+	reg |= BM_CLKCTRL_ENET_CLK_OUT_EN;
+	__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
+
+	return 0;
+}
+
+int __init mx28_clocks_init(void)
+{
+	clk_misc_init();
+
+	clkdev_add_table(lookups, ARRAY_SIZE(lookups));
+
+	mxs_timer_init(&clk32k_clk, MX28_INT_TIMER0);
+
+	return 0;
+}
diff --git a/arch/arm/mach-mxs/clock.c b/arch/arm/mach-mxs/clock.c
new file mode 100644
index 0000000..e7d2269
--- /dev/null
+++ b/arch/arm/mach-mxs/clock.c
@@ -0,0 +1,200 @@
+/*
+ * Based on arch/arm/plat-omap/clock.c
+ *
+ * Copyright (C) 2004 - 2005 Nokia corporation
+ * Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com>
+ * Modified for omap shared clock framework by Tony Lindgren <tony@atomide.com>
+ * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2008 Juergen Beisert, kernel at pengutronix.de
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA  02110-1301, USA.
+ */
+
+/* #define DEBUG */
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/proc_fs.h>
+#include <linux/semaphore.h>
+#include <linux/string.h>
+
+#include <mach/clock.h>
+
+static LIST_HEAD(clocks);
+static DEFINE_MUTEX(clocks_mutex);
+
+/*-------------------------------------------------------------------------
+ * Standard clock functions defined in include/linux/clk.h
+ *-------------------------------------------------------------------------*/
+
+static void __clk_disable(struct clk *clk)
+{
+	if (clk == NULL || IS_ERR(clk))
+		return;
+	WARN_ON(!clk->usecount);
+
+	if (!(--clk->usecount)) {
+		if (clk->disable)
+			clk->disable(clk);
+		__clk_disable(clk->parent);
+		__clk_disable(clk->secondary);
+	}
+}
+
+static int __clk_enable(struct clk *clk)
+{
+	if (clk == NULL || IS_ERR(clk))
+		return -EINVAL;
+
+	if (clk->usecount++ == 0) {
+		__clk_enable(clk->parent);
+		__clk_enable(clk->secondary);
+
+		if (clk->enable)
+			clk->enable(clk);
+	}
+	return 0;
+}
+
+/* This function increments the reference count on the clock and enables the
+ * clock if not already enabled. The parent clock tree is recursively enabled
+ */
+int clk_enable(struct clk *clk)
+{
+	int ret = 0;
+
+	if (clk == NULL || IS_ERR(clk))
+		return -EINVAL;
+
+	mutex_lock(&clocks_mutex);
+	ret = __clk_enable(clk);
+	mutex_unlock(&clocks_mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL(clk_enable);
+
+/* This function decrements the reference count on the clock and disables
+ * the clock when reference count is 0. The parent clock tree is
+ * recursively disabled
+ */
+void clk_disable(struct clk *clk)
+{
+	if (clk == NULL || IS_ERR(clk))
+		return;
+
+	mutex_lock(&clocks_mutex);
+	__clk_disable(clk);
+	mutex_unlock(&clocks_mutex);
+}
+EXPORT_SYMBOL(clk_disable);
+
+/* Retrieve the *current* clock rate. If the clock itself
+ * does not provide a special calculation routine, ask
+ * its parent and so on, until one is able to return
+ * a valid clock rate
+ */
+unsigned long clk_get_rate(struct clk *clk)
+{
+	if (clk == NULL || IS_ERR(clk))
+		return 0UL;
+
+	if (clk->get_rate)
+		return clk->get_rate(clk);
+
+	return clk_get_rate(clk->parent);
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+/* Round the requested clock rate to the nearest supported
+ * rate that is less than or equal to the requested rate.
+ * This is dependent on the clock's current parent.
+ */
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	if (clk == NULL || IS_ERR(clk) || !clk->round_rate)
+		return 0;
+
+	return clk->round_rate(clk, rate);
+}
+EXPORT_SYMBOL(clk_round_rate);
+
+/* Set the clock to the requested clock rate. The rate must
+ * match a supported rate exactly based on what clk_round_rate returns
+ */
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	int ret = -EINVAL;
+
+	if (clk == NULL || IS_ERR(clk) || clk->set_rate == NULL || rate == 0)
+		return ret;
+
+	mutex_lock(&clocks_mutex);
+	ret = clk->set_rate(clk, rate);
+	mutex_unlock(&clocks_mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL(clk_set_rate);
+
+/* Set the clock's parent to another clock source */
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	int ret = -EINVAL;
+	struct clk *old;
+
+	if (clk == NULL || IS_ERR(clk) || parent == NULL ||
+	    IS_ERR(parent) || clk->set_parent == NULL)
+		return ret;
+
+	if (clk->usecount)
+		clk_enable(parent);
+
+	mutex_lock(&clocks_mutex);
+	ret = clk->set_parent(clk, parent);
+	if (ret == 0) {
+		old = clk->parent;
+		clk->parent = parent;
+	} else {
+		old = parent;
+	}
+	mutex_unlock(&clocks_mutex);
+
+	if (clk->usecount)
+		clk_disable(old);
+
+	return ret;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
+/* Retrieve the clock's parent clock source */
+struct clk *clk_get_parent(struct clk *clk)
+{
+	struct clk *ret = NULL;
+
+	if (clk == NULL || IS_ERR(clk))
+		return ret;
+
+	return clk->parent;
+}
+EXPORT_SYMBOL(clk_get_parent);
diff --git a/arch/arm/mach-mxs/include/mach/clkdev.h b/arch/arm/mach-mxs/include/mach/clkdev.h
new file mode 100644
index 0000000..3a8f2e3
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/clkdev.h
@@ -0,0 +1,7 @@
+#ifndef __MACH_MXS_CLKDEV_H__
+#define __MACH_MXS_CLKDEV_H__
+
+#define __clk_get(clk) ({ 1; })
+#define __clk_put(clk) do { } while (0)
+
+#endif
diff --git a/arch/arm/mach-mxs/include/mach/clock.h b/arch/arm/mach-mxs/include/mach/clock.h
new file mode 100644
index 0000000..041e276
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/clock.h
@@ -0,0 +1,64 @@
+/*
+ * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2008 Juergen Beisert, kernel at pengutronix.de
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA  02110-1301, USA.
+ */
+
+#ifndef __MACH_MXS_CLOCK_H__
+#define __MACH_MXS_CLOCK_H__
+
+#ifndef __ASSEMBLY__
+#include <linux/list.h>
+
+struct module;
+
+struct clk {
+	int id;
+	/* Source clock this clk depends on */
+	struct clk *parent;
+	/* Secondary clock to enable/disable with this clock */
+	struct clk *secondary;
+	/* Reference count of clock enable/disable */
+	__s8 usecount;
+	/* Register bit position for clock's enable/disable control. */
+	u8 enable_shift;
+	/* Register address for clock's enable/disable control. */
+	void __iomem *enable_reg;
+	u32 flags;
+	/* get the current clock rate (always a fresh value) */
+	unsigned long (*get_rate) (struct clk *);
+	/* Function ptr to set the clock to a new rate. The rate must match a
+	   supported rate returned from round_rate. Leave blank if clock is not
+	   programmable */
+	int (*set_rate) (struct clk *, unsigned long);
+	/* Function ptr to round the requested clock rate to the nearest
+	   supported rate that is less than or equal to the requested rate. */
+	unsigned long (*round_rate) (struct clk *, unsigned long);
+	/* Function ptr to enable the clock. Leave blank if clock can not
+	   be gated. */
+	int (*enable) (struct clk *);
+	/* Function ptr to disable the clock. Leave blank if clock can not
+	   be gated. */
+	void (*disable) (struct clk *);
+	/* Function ptr to set the parent clock of the clock. */
+	int (*set_parent) (struct clk *, struct clk *);
+};
+
+int clk_register(struct clk *clk);
+void clk_unregister(struct clk *clk);
+
+#endif /* __ASSEMBLY__ */
+#endif /* __MACH_MXS_CLOCK_H__ */
diff --git a/arch/arm/mach-mxs/regs-clkctrl-mx23.h b/arch/arm/mach-mxs/regs-clkctrl-mx23.h
new file mode 100644
index 0000000..dbc0474
--- /dev/null
+++ b/arch/arm/mach-mxs/regs-clkctrl-mx23.h
@@ -0,0 +1,455 @@
+/*
+ * Freescale CLKCTRL Register Definitions
+ *
+ * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved.
+ * Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
+ *
+ * This file is created by xml file. Don't Edit it.
+ *
+ * Xml Revision: 1.48
+ * Template revision: 26195
+ */
+
+#ifndef __REGS_CLKCTRL_MX23_H__
+#define __REGS_CLKCTRL_MX23_H__
+
+
+#define HW_CLKCTRL_PLLCTRL0	(0x00000000)
+#define HW_CLKCTRL_PLLCTRL0_SET	(0x00000004)
+#define HW_CLKCTRL_PLLCTRL0_CLR	(0x00000008)
+#define HW_CLKCTRL_PLLCTRL0_TOG	(0x0000000c)
+
+#define BP_CLKCTRL_PLLCTRL0_RSRVD6	30
+#define BM_CLKCTRL_PLLCTRL0_RSRVD6	0xC0000000
+#define BF_CLKCTRL_PLLCTRL0_RSRVD6(v) \
+		(((v) << 30) & BM_CLKCTRL_PLLCTRL0_RSRVD6)
+#define BP_CLKCTRL_PLLCTRL0_LFR_SEL	28
+#define BM_CLKCTRL_PLLCTRL0_LFR_SEL	0x30000000
+#define BF_CLKCTRL_PLLCTRL0_LFR_SEL(v)  \
+		(((v) << 28) & BM_CLKCTRL_PLLCTRL0_LFR_SEL)
+#define BV_CLKCTRL_PLLCTRL0_LFR_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLLCTRL0_LFR_SEL__TIMES_2   0x1
+#define BV_CLKCTRL_PLLCTRL0_LFR_SEL__TIMES_05  0x2
+#define BV_CLKCTRL_PLLCTRL0_LFR_SEL__UNDEFINED 0x3
+#define BP_CLKCTRL_PLLCTRL0_RSRVD5	26
+#define BM_CLKCTRL_PLLCTRL0_RSRVD5	0x0C000000
+#define BF_CLKCTRL_PLLCTRL0_RSRVD5(v)  \
+		(((v) << 26) & BM_CLKCTRL_PLLCTRL0_RSRVD5)
+#define BP_CLKCTRL_PLLCTRL0_CP_SEL	24
+#define BM_CLKCTRL_PLLCTRL0_CP_SEL	0x03000000
+#define BF_CLKCTRL_PLLCTRL0_CP_SEL(v)  \
+		(((v) << 24) & BM_CLKCTRL_PLLCTRL0_CP_SEL)
+#define BV_CLKCTRL_PLLCTRL0_CP_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLLCTRL0_CP_SEL__TIMES_2   0x1
+#define BV_CLKCTRL_PLLCTRL0_CP_SEL__TIMES_05  0x2
+#define BV_CLKCTRL_PLLCTRL0_CP_SEL__UNDEFINED 0x3
+#define BP_CLKCTRL_PLLCTRL0_RSRVD4	22
+#define BM_CLKCTRL_PLLCTRL0_RSRVD4	0x00C00000
+#define BF_CLKCTRL_PLLCTRL0_RSRVD4(v)  \
+		(((v) << 22) & BM_CLKCTRL_PLLCTRL0_RSRVD4)
+#define BP_CLKCTRL_PLLCTRL0_DIV_SEL	20
+#define BM_CLKCTRL_PLLCTRL0_DIV_SEL	0x00300000
+#define BF_CLKCTRL_PLLCTRL0_DIV_SEL(v)  \
+		(((v) << 20) & BM_CLKCTRL_PLLCTRL0_DIV_SEL)
+#define BV_CLKCTRL_PLLCTRL0_DIV_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLLCTRL0_DIV_SEL__LOWER     0x1
+#define BV_CLKCTRL_PLLCTRL0_DIV_SEL__LOWEST    0x2
+#define BV_CLKCTRL_PLLCTRL0_DIV_SEL__UNDEFINED 0x3
+#define BM_CLKCTRL_PLLCTRL0_RSRVD3	0x00080000
+#define BM_CLKCTRL_PLLCTRL0_EN_USB_CLKS	0x00040000
+#define BM_CLKCTRL_PLLCTRL0_RSRVD2	0x00020000
+#define BM_CLKCTRL_PLLCTRL0_POWER	0x00010000
+#define BP_CLKCTRL_PLLCTRL0_RSRVD1	0
+#define BM_CLKCTRL_PLLCTRL0_RSRVD1	0x0000FFFF
+#define BF_CLKCTRL_PLLCTRL0_RSRVD1(v)  \
+		(((v) << 0) & BM_CLKCTRL_PLLCTRL0_RSRVD1)
+
+#define HW_CLKCTRL_PLLCTRL1	(0x00000010)
+
+#define BM_CLKCTRL_PLLCTRL1_LOCK	0x80000000
+#define BM_CLKCTRL_PLLCTRL1_FORCE_LOCK	0x40000000
+#define BP_CLKCTRL_PLLCTRL1_RSRVD1	16
+#define BM_CLKCTRL_PLLCTRL1_RSRVD1	0x3FFF0000
+#define BF_CLKCTRL_PLLCTRL1_RSRVD1(v)  \
+		(((v) << 16) & BM_CLKCTRL_PLLCTRL1_RSRVD1)
+#define BP_CLKCTRL_PLLCTRL1_LOCK_COUNT	0
+#define BM_CLKCTRL_PLLCTRL1_LOCK_COUNT	0x0000FFFF
+#define BF_CLKCTRL_PLLCTRL1_LOCK_COUNT(v)  \
+		(((v) << 0) & BM_CLKCTRL_PLLCTRL1_LOCK_COUNT)
+
+#define HW_CLKCTRL_CPU	(0x00000020)
+#define HW_CLKCTRL_CPU_SET	(0x00000024)
+#define HW_CLKCTRL_CPU_CLR	(0x00000028)
+#define HW_CLKCTRL_CPU_TOG	(0x0000002c)
+
+#define BP_CLKCTRL_CPU_RSRVD5	30
+#define BM_CLKCTRL_CPU_RSRVD5	0xC0000000
+#define BF_CLKCTRL_CPU_RSRVD5(v) \
+		(((v) << 30) & BM_CLKCTRL_CPU_RSRVD5)
+#define BM_CLKCTRL_CPU_BUSY_REF_XTAL	0x20000000
+#define BM_CLKCTRL_CPU_BUSY_REF_CPU	0x10000000
+#define BM_CLKCTRL_CPU_RSRVD4	0x08000000
+#define BM_CLKCTRL_CPU_DIV_XTAL_FRAC_EN	0x04000000
+#define BP_CLKCTRL_CPU_DIV_XTAL	16
+#define BM_CLKCTRL_CPU_DIV_XTAL	0x03FF0000
+#define BF_CLKCTRL_CPU_DIV_XTAL(v)  \
+		(((v) << 16) & BM_CLKCTRL_CPU_DIV_XTAL)
+#define BP_CLKCTRL_CPU_RSRVD3	13
+#define BM_CLKCTRL_CPU_RSRVD3	0x0000E000
+#define BF_CLKCTRL_CPU_RSRVD3(v)  \
+		(((v) << 13) & BM_CLKCTRL_CPU_RSRVD3)
+#define BM_CLKCTRL_CPU_INTERRUPT_WAIT	0x00001000
+#define BM_CLKCTRL_CPU_RSRVD2	0x00000800
+#define BM_CLKCTRL_CPU_DIV_CPU_FRAC_EN	0x00000400
+#define BP_CLKCTRL_CPU_RSRVD1	6
+#define BM_CLKCTRL_CPU_RSRVD1	0x000003C0
+#define BF_CLKCTRL_CPU_RSRVD1(v)  \
+		(((v) << 6) & BM_CLKCTRL_CPU_RSRVD1)
+#define BP_CLKCTRL_CPU_DIV_CPU	0
+#define BM_CLKCTRL_CPU_DIV_CPU	0x0000003F
+#define BF_CLKCTRL_CPU_DIV_CPU(v)  \
+		(((v) << 0) & BM_CLKCTRL_CPU_DIV_CPU)
+
+#define HW_CLKCTRL_HBUS	(0x00000030)
+#define HW_CLKCTRL_HBUS_SET	(0x00000034)
+#define HW_CLKCTRL_HBUS_CLR	(0x00000038)
+#define HW_CLKCTRL_HBUS_TOG	(0x0000003c)
+
+#define BP_CLKCTRL_HBUS_RSRVD4	30
+#define BM_CLKCTRL_HBUS_RSRVD4	0xC0000000
+#define BF_CLKCTRL_HBUS_RSRVD4(v) \
+		(((v) << 30) & BM_CLKCTRL_HBUS_RSRVD4)
+#define BM_CLKCTRL_HBUS_BUSY	0x20000000
+#define BM_CLKCTRL_HBUS_DCP_AS_ENABLE	0x10000000
+#define BM_CLKCTRL_HBUS_PXP_AS_ENABLE	0x08000000
+#define BM_CLKCTRL_HBUS_APBHDMA_AS_ENABLE	0x04000000
+#define BM_CLKCTRL_HBUS_APBXDMA_AS_ENABLE	0x02000000
+#define BM_CLKCTRL_HBUS_TRAFFIC_JAM_AS_ENABLE	0x01000000
+#define BM_CLKCTRL_HBUS_TRAFFIC_AS_ENABLE	0x00800000
+#define BM_CLKCTRL_HBUS_CPU_DATA_AS_ENABLE	0x00400000
+#define BM_CLKCTRL_HBUS_CPU_INSTR_AS_ENABLE	0x00200000
+#define BM_CLKCTRL_HBUS_AUTO_SLOW_MODE	0x00100000
+#define BM_CLKCTRL_HBUS_RSRVD2	0x00080000
+#define BP_CLKCTRL_HBUS_SLOW_DIV	16
+#define BM_CLKCTRL_HBUS_SLOW_DIV	0x00070000
+#define BF_CLKCTRL_HBUS_SLOW_DIV(v)  \
+		(((v) << 16) & BM_CLKCTRL_HBUS_SLOW_DIV)
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY1  0x0
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY2  0x1
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY4  0x2
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY8  0x3
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY16 0x4
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY32 0x5
+#define BP_CLKCTRL_HBUS_RSRVD1	6
+#define BM_CLKCTRL_HBUS_RSRVD1	0x0000FFC0
+#define BF_CLKCTRL_HBUS_RSRVD1(v)  \
+		(((v) << 6) & BM_CLKCTRL_HBUS_RSRVD1)
+#define BM_CLKCTRL_HBUS_DIV_FRAC_EN	0x00000020
+#define BP_CLKCTRL_HBUS_DIV	0
+#define BM_CLKCTRL_HBUS_DIV	0x0000001F
+#define BF_CLKCTRL_HBUS_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_HBUS_DIV)
+
+#define HW_CLKCTRL_XBUS	(0x00000040)
+
+#define BM_CLKCTRL_XBUS_BUSY	0x80000000
+#define BP_CLKCTRL_XBUS_RSRVD1	11
+#define BM_CLKCTRL_XBUS_RSRVD1	0x7FFFF800
+#define BF_CLKCTRL_XBUS_RSRVD1(v)  \
+		(((v) << 11) & BM_CLKCTRL_XBUS_RSRVD1)
+#define BM_CLKCTRL_XBUS_DIV_FRAC_EN	0x00000400
+#define BP_CLKCTRL_XBUS_DIV	0
+#define BM_CLKCTRL_XBUS_DIV	0x000003FF
+#define BF_CLKCTRL_XBUS_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_XBUS_DIV)
+
+#define HW_CLKCTRL_XTAL	(0x00000050)
+#define HW_CLKCTRL_XTAL_SET	(0x00000054)
+#define HW_CLKCTRL_XTAL_CLR	(0x00000058)
+#define HW_CLKCTRL_XTAL_TOG	(0x0000005c)
+
+#define BP_CLKCTRL_XTAL_UART_CLK_GATE	31
+#define BM_CLKCTRL_XTAL_UART_CLK_GATE	0x80000000
+#define BP_CLKCTRL_XTAL_FILT_CLK24M_GATE	30
+#define BM_CLKCTRL_XTAL_FILT_CLK24M_GATE	0x40000000
+#define BP_CLKCTRL_XTAL_PWM_CLK24M_GATE	29
+#define BM_CLKCTRL_XTAL_PWM_CLK24M_GATE	0x20000000
+#define BM_CLKCTRL_XTAL_DRI_CLK24M_GATE	0x10000000
+#define BM_CLKCTRL_XTAL_DIGCTRL_CLK1M_GATE	0x08000000
+#define BP_CLKCTRL_XTAL_TIMROT_CLK32K_GATE	26
+#define BM_CLKCTRL_XTAL_TIMROT_CLK32K_GATE	0x04000000
+#define BP_CLKCTRL_XTAL_RSRVD1	2
+#define BM_CLKCTRL_XTAL_RSRVD1	0x03FFFFFC
+#define BF_CLKCTRL_XTAL_RSRVD1(v)  \
+		(((v) << 2) & BM_CLKCTRL_XTAL_RSRVD1)
+#define BP_CLKCTRL_XTAL_DIV_UART	0
+#define BM_CLKCTRL_XTAL_DIV_UART	0x00000003
+#define BF_CLKCTRL_XTAL_DIV_UART(v)  \
+		(((v) << 0) & BM_CLKCTRL_XTAL_DIV_UART)
+
+#define HW_CLKCTRL_PIX	(0x00000060)
+
+#define BP_CLKCTRL_PIX_CLKGATE	31
+#define BM_CLKCTRL_PIX_CLKGATE	0x80000000
+#define BM_CLKCTRL_PIX_RSRVD2	0x40000000
+#define BM_CLKCTRL_PIX_BUSY	0x20000000
+#define BP_CLKCTRL_PIX_RSRVD1	13
+#define BM_CLKCTRL_PIX_RSRVD1	0x1FFFE000
+#define BF_CLKCTRL_PIX_RSRVD1(v)  \
+		(((v) << 13) & BM_CLKCTRL_PIX_RSRVD1)
+#define BM_CLKCTRL_PIX_DIV_FRAC_EN	0x00001000
+#define BP_CLKCTRL_PIX_DIV	0
+#define BM_CLKCTRL_PIX_DIV	0x00000FFF
+#define BF_CLKCTRL_PIX_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_PIX_DIV)
+
+#define HW_CLKCTRL_SSP	(0x00000070)
+
+#define BP_CLKCTRL_SSP_CLKGATE	31
+#define BM_CLKCTRL_SSP_CLKGATE	0x80000000
+#define BM_CLKCTRL_SSP_RSRVD2	0x40000000
+#define BM_CLKCTRL_SSP_BUSY	0x20000000
+#define BP_CLKCTRL_SSP_RSRVD1	10
+#define BM_CLKCTRL_SSP_RSRVD1	0x1FFFFC00
+#define BF_CLKCTRL_SSP_RSRVD1(v)  \
+		(((v) << 10) & BM_CLKCTRL_SSP_RSRVD1)
+#define BM_CLKCTRL_SSP_DIV_FRAC_EN	0x00000200
+#define BP_CLKCTRL_SSP_DIV	0
+#define BM_CLKCTRL_SSP_DIV	0x000001FF
+#define BF_CLKCTRL_SSP_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_SSP_DIV)
+
+#define HW_CLKCTRL_GPMI	(0x00000080)
+
+#define BP_CLKCTRL_GPMI_CLKGATE	31
+#define BM_CLKCTRL_GPMI_CLKGATE	0x80000000
+#define BM_CLKCTRL_GPMI_RSRVD2	0x40000000
+#define BM_CLKCTRL_GPMI_BUSY	0x20000000
+#define BP_CLKCTRL_GPMI_RSRVD1	11
+#define BM_CLKCTRL_GPMI_RSRVD1	0x1FFFF800
+#define BF_CLKCTRL_GPMI_RSRVD1(v)  \
+		(((v) << 11) & BM_CLKCTRL_GPMI_RSRVD1)
+#define BM_CLKCTRL_GPMI_DIV_FRAC_EN	0x00000400
+#define BP_CLKCTRL_GPMI_DIV	0
+#define BM_CLKCTRL_GPMI_DIV	0x000003FF
+#define BF_CLKCTRL_GPMI_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_GPMI_DIV)
+
+#define HW_CLKCTRL_SPDIF	(0x00000090)
+
+#define BM_CLKCTRL_SPDIF_CLKGATE	0x80000000
+#define BP_CLKCTRL_SPDIF_RSRVD	0
+#define BM_CLKCTRL_SPDIF_RSRVD	0x7FFFFFFF
+#define BF_CLKCTRL_SPDIF_RSRVD(v)  \
+		(((v) << 0) & BM_CLKCTRL_SPDIF_RSRVD)
+
+#define HW_CLKCTRL_EMI	(0x000000a0)
+
+#define BP_CLKCTRL_EMI_CLKGATE	31
+#define BM_CLKCTRL_EMI_CLKGATE	0x80000000
+#define BM_CLKCTRL_EMI_SYNC_MODE_EN	0x40000000
+#define BM_CLKCTRL_EMI_BUSY_REF_XTAL	0x20000000
+#define BM_CLKCTRL_EMI_BUSY_REF_EMI	0x10000000
+#define BM_CLKCTRL_EMI_BUSY_REF_CPU	0x08000000
+#define BM_CLKCTRL_EMI_BUSY_SYNC_MODE	0x04000000
+#define BP_CLKCTRL_EMI_RSRVD3	18
+#define BM_CLKCTRL_EMI_RSRVD3	0x03FC0000
+#define BF_CLKCTRL_EMI_RSRVD3(v)  \
+		(((v) << 18) & BM_CLKCTRL_EMI_RSRVD3)
+#define BM_CLKCTRL_EMI_BUSY_DCC_RESYNC	0x00020000
+#define BM_CLKCTRL_EMI_DCC_RESYNC_ENABLE	0x00010000
+#define BP_CLKCTRL_EMI_RSRVD2	12
+#define BM_CLKCTRL_EMI_RSRVD2	0x0000F000
+#define BF_CLKCTRL_EMI_RSRVD2(v)  \
+		(((v) << 12) & BM_CLKCTRL_EMI_RSRVD2)
+#define BP_CLKCTRL_EMI_DIV_XTAL	8
+#define BM_CLKCTRL_EMI_DIV_XTAL	0x00000F00
+#define BF_CLKCTRL_EMI_DIV_XTAL(v)  \
+		(((v) << 8) & BM_CLKCTRL_EMI_DIV_XTAL)
+#define BP_CLKCTRL_EMI_RSRVD1	6
+#define BM_CLKCTRL_EMI_RSRVD1	0x000000C0
+#define BF_CLKCTRL_EMI_RSRVD1(v)  \
+		(((v) << 6) & BM_CLKCTRL_EMI_RSRVD1)
+#define BP_CLKCTRL_EMI_DIV_EMI	0
+#define BM_CLKCTRL_EMI_DIV_EMI	0x0000003F
+#define BF_CLKCTRL_EMI_DIV_EMI(v)  \
+		(((v) << 0) & BM_CLKCTRL_EMI_DIV_EMI)
+
+#define HW_CLKCTRL_IR	(0x000000b0)
+
+#define BM_CLKCTRL_IR_CLKGATE	0x80000000
+#define BM_CLKCTRL_IR_RSRVD3	0x40000000
+#define BM_CLKCTRL_IR_AUTO_DIV	0x20000000
+#define BM_CLKCTRL_IR_IR_BUSY	0x10000000
+#define BM_CLKCTRL_IR_IROV_BUSY	0x08000000
+#define BP_CLKCTRL_IR_RSRVD2	25
+#define BM_CLKCTRL_IR_RSRVD2	0x06000000
+#define BF_CLKCTRL_IR_RSRVD2(v)  \
+		(((v) << 25) & BM_CLKCTRL_IR_RSRVD2)
+#define BP_CLKCTRL_IR_IROV_DIV	16
+#define BM_CLKCTRL_IR_IROV_DIV	0x01FF0000
+#define BF_CLKCTRL_IR_IROV_DIV(v)  \
+		(((v) << 16) & BM_CLKCTRL_IR_IROV_DIV)
+#define BP_CLKCTRL_IR_RSRVD1	10
+#define BM_CLKCTRL_IR_RSRVD1	0x0000FC00
+#define BF_CLKCTRL_IR_RSRVD1(v)  \
+		(((v) << 10) & BM_CLKCTRL_IR_RSRVD1)
+#define BP_CLKCTRL_IR_IR_DIV	0
+#define BM_CLKCTRL_IR_IR_DIV	0x000003FF
+#define BF_CLKCTRL_IR_IR_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_IR_IR_DIV)
+
+#define HW_CLKCTRL_SAIF	(0x000000c0)
+
+#define BM_CLKCTRL_SAIF_CLKGATE	0x80000000
+#define BM_CLKCTRL_SAIF_RSRVD2	0x40000000
+#define BM_CLKCTRL_SAIF_BUSY	0x20000000
+#define BP_CLKCTRL_SAIF_RSRVD1	17
+#define BM_CLKCTRL_SAIF_RSRVD1	0x1FFE0000
+#define BF_CLKCTRL_SAIF_RSRVD1(v)  \
+		(((v) << 17) & BM_CLKCTRL_SAIF_RSRVD1)
+#define BM_CLKCTRL_SAIF_DIV_FRAC_EN	0x00010000
+#define BP_CLKCTRL_SAIF_DIV	0
+#define BM_CLKCTRL_SAIF_DIV	0x0000FFFF
+#define BF_CLKCTRL_SAIF_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_SAIF_DIV)
+
+#define HW_CLKCTRL_TV	(0x000000d0)
+
+#define BM_CLKCTRL_TV_CLK_TV108M_GATE	0x80000000
+#define BM_CLKCTRL_TV_CLK_TV_GATE	0x40000000
+#define BP_CLKCTRL_TV_RSRVD	0
+#define BM_CLKCTRL_TV_RSRVD	0x3FFFFFFF
+#define BF_CLKCTRL_TV_RSRVD(v)  \
+		(((v) << 0) & BM_CLKCTRL_TV_RSRVD)
+
+#define HW_CLKCTRL_ETM	(0x000000e0)
+
+#define BM_CLKCTRL_ETM_CLKGATE	0x80000000
+#define BM_CLKCTRL_ETM_RSRVD2	0x40000000
+#define BM_CLKCTRL_ETM_BUSY	0x20000000
+#define BP_CLKCTRL_ETM_RSRVD1	7
+#define BM_CLKCTRL_ETM_RSRVD1	0x1FFFFF80
+#define BF_CLKCTRL_ETM_RSRVD1(v)  \
+		(((v) << 7) & BM_CLKCTRL_ETM_RSRVD1)
+#define BM_CLKCTRL_ETM_DIV_FRAC_EN	0x00000040
+#define BP_CLKCTRL_ETM_DIV	0
+#define BM_CLKCTRL_ETM_DIV	0x0000003F
+#define BF_CLKCTRL_ETM_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_ETM_DIV)
+
+#define HW_CLKCTRL_FRAC	(0x000000f0)
+#define HW_CLKCTRL_FRAC_SET	(0x000000f4)
+#define HW_CLKCTRL_FRAC_CLR	(0x000000f8)
+#define HW_CLKCTRL_FRAC_TOG	(0x000000fc)
+
+#define BP_CLKCTRL_FRAC_CLKGATEIO	31
+#define BM_CLKCTRL_FRAC_CLKGATEIO	0x80000000
+#define BM_CLKCTRL_FRAC_IO_STABLE	0x40000000
+#define BP_CLKCTRL_FRAC_IOFRAC	24
+#define BM_CLKCTRL_FRAC_IOFRAC	0x3F000000
+#define BF_CLKCTRL_FRAC_IOFRAC(v)  \
+		(((v) << 24) & BM_CLKCTRL_FRAC_IOFRAC)
+#define BP_CLKCTRL_FRAC_CLKGATEPIX	23
+#define BM_CLKCTRL_FRAC_CLKGATEPIX	0x00800000
+#define BM_CLKCTRL_FRAC_PIX_STABLE	0x00400000
+#define BP_CLKCTRL_FRAC_PIXFRAC	16
+#define BM_CLKCTRL_FRAC_PIXFRAC	0x003F0000
+#define BF_CLKCTRL_FRAC_PIXFRAC(v)  \
+		(((v) << 16) & BM_CLKCTRL_FRAC_PIXFRAC)
+#define BP_CLKCTRL_FRAC_CLKGATEEMI	15
+#define BM_CLKCTRL_FRAC_CLKGATEEMI	0x00008000
+#define BM_CLKCTRL_FRAC_EMI_STABLE	0x00004000
+#define BP_CLKCTRL_FRAC_EMIFRAC	8
+#define BM_CLKCTRL_FRAC_EMIFRAC	0x00003F00
+#define BF_CLKCTRL_FRAC_EMIFRAC(v)  \
+		(((v) << 8) & BM_CLKCTRL_FRAC_EMIFRAC)
+#define BP_CLKCTRL_FRAC_CLKGATECPU	7
+#define BM_CLKCTRL_FRAC_CLKGATECPU	0x00000080
+#define BM_CLKCTRL_FRAC_CPU_STABLE	0x00000040
+#define BP_CLKCTRL_FRAC_CPUFRAC	0
+#define BM_CLKCTRL_FRAC_CPUFRAC	0x0000003F
+#define BF_CLKCTRL_FRAC_CPUFRAC(v)  \
+		(((v) << 0) & BM_CLKCTRL_FRAC_CPUFRAC)
+
+#define HW_CLKCTRL_FRAC1	(0x00000100)
+#define HW_CLKCTRL_FRAC1_SET	(0x00000104)
+#define HW_CLKCTRL_FRAC1_CLR	(0x00000108)
+#define HW_CLKCTRL_FRAC1_TOG	(0x0000010c)
+
+#define BM_CLKCTRL_FRAC1_CLKGATEVID	0x80000000
+#define BM_CLKCTRL_FRAC1_VID_STABLE	0x40000000
+#define BP_CLKCTRL_FRAC1_RSRVD1	0
+#define BM_CLKCTRL_FRAC1_RSRVD1	0x3FFFFFFF
+#define BF_CLKCTRL_FRAC1_RSRVD1(v)  \
+		(((v) << 0) & BM_CLKCTRL_FRAC1_RSRVD1)
+
+#define HW_CLKCTRL_CLKSEQ	(0x00000110)
+#define HW_CLKCTRL_CLKSEQ_SET	(0x00000114)
+#define HW_CLKCTRL_CLKSEQ_CLR	(0x00000118)
+#define HW_CLKCTRL_CLKSEQ_TOG	(0x0000011c)
+
+#define BP_CLKCTRL_CLKSEQ_RSRVD1	9
+#define BM_CLKCTRL_CLKSEQ_RSRVD1	0xFFFFFE00
+#define BF_CLKCTRL_CLKSEQ_RSRVD1(v) \
+		(((v) << 9) & BM_CLKCTRL_CLKSEQ_RSRVD1)
+#define BM_CLKCTRL_CLKSEQ_BYPASS_ETM	0x00000100
+#define BM_CLKCTRL_CLKSEQ_BYPASS_CPU	0x00000080
+#define BM_CLKCTRL_CLKSEQ_BYPASS_EMI	0x00000040
+#define BM_CLKCTRL_CLKSEQ_BYPASS_SSP	0x00000020
+#define BM_CLKCTRL_CLKSEQ_BYPASS_GPMI	0x00000010
+#define BM_CLKCTRL_CLKSEQ_BYPASS_IR	0x00000008
+#define BM_CLKCTRL_CLKSEQ_RSRVD0	0x00000004
+#define BM_CLKCTRL_CLKSEQ_BYPASS_PIX	0x00000002
+#define BM_CLKCTRL_CLKSEQ_BYPASS_SAIF	0x00000001
+
+#define HW_CLKCTRL_RESET	(0x00000120)
+
+#define BP_CLKCTRL_RESET_RSRVD	2
+#define BM_CLKCTRL_RESET_RSRVD	0xFFFFFFFC
+#define BF_CLKCTRL_RESET_RSRVD(v) \
+		(((v) << 2) & BM_CLKCTRL_RESET_RSRVD)
+#define BM_CLKCTRL_RESET_CHIP	0x00000002
+#define BM_CLKCTRL_RESET_DIG	0x00000001
+
+#define HW_CLKCTRL_STATUS	(0x00000130)
+
+#define BP_CLKCTRL_STATUS_CPU_LIMIT	30
+#define BM_CLKCTRL_STATUS_CPU_LIMIT	0xC0000000
+#define BF_CLKCTRL_STATUS_CPU_LIMIT(v) \
+		(((v) << 30) & BM_CLKCTRL_STATUS_CPU_LIMIT)
+#define BP_CLKCTRL_STATUS_RSRVD	0
+#define BM_CLKCTRL_STATUS_RSRVD	0x3FFFFFFF
+#define BF_CLKCTRL_STATUS_RSRVD(v)  \
+		(((v) << 0) & BM_CLKCTRL_STATUS_RSRVD)
+
+#define HW_CLKCTRL_VERSION	(0x00000140)
+
+#define BP_CLKCTRL_VERSION_MAJOR	24
+#define BM_CLKCTRL_VERSION_MAJOR	0xFF000000
+#define BF_CLKCTRL_VERSION_MAJOR(v) \
+		(((v) << 24) & BM_CLKCTRL_VERSION_MAJOR)
+#define BP_CLKCTRL_VERSION_MINOR	16
+#define BM_CLKCTRL_VERSION_MINOR	0x00FF0000
+#define BF_CLKCTRL_VERSION_MINOR(v)  \
+		(((v) << 16) & BM_CLKCTRL_VERSION_MINOR)
+#define BP_CLKCTRL_VERSION_STEP	0
+#define BM_CLKCTRL_VERSION_STEP	0x0000FFFF
+#define BF_CLKCTRL_VERSION_STEP(v)  \
+		(((v) << 0) & BM_CLKCTRL_VERSION_STEP)
+
+#endif /* __REGS_CLKCTRL_MX23_H__ */
diff --git a/arch/arm/mach-mxs/regs-clkctrl-mx28.h b/arch/arm/mach-mxs/regs-clkctrl-mx28.h
new file mode 100644
index 0000000..661df18
--- /dev/null
+++ b/arch/arm/mach-mxs/regs-clkctrl-mx28.h
@@ -0,0 +1,663 @@
+/*
+ * Freescale CLKCTRL Register Definitions
+ *
+ * Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
+ *
+ * This file is created by xml file. Don't Edit it.
+ *
+ * Xml Revision: 1.48
+ * Template revision: 26195
+ */
+
+#ifndef __REGS_CLKCTRL_MX28_H__
+#define __REGS_CLKCTRL_MX28_H__
+
+#define HW_CLKCTRL_PLL0CTRL0	(0x00000000)
+#define HW_CLKCTRL_PLL0CTRL0_SET	(0x00000004)
+#define HW_CLKCTRL_PLL0CTRL0_CLR	(0x00000008)
+#define HW_CLKCTRL_PLL0CTRL0_TOG	(0x0000000c)
+
+#define BP_CLKCTRL_PLL0CTRL0_RSRVD6	30
+#define BM_CLKCTRL_PLL0CTRL0_RSRVD6	0xC0000000
+#define BF_CLKCTRL_PLL0CTRL0_RSRVD6(v) \
+		(((v) << 30) & BM_CLKCTRL_PLL0CTRL0_RSRVD6)
+#define BP_CLKCTRL_PLL0CTRL0_LFR_SEL	28
+#define BM_CLKCTRL_PLL0CTRL0_LFR_SEL	0x30000000
+#define BF_CLKCTRL_PLL0CTRL0_LFR_SEL(v)  \
+		(((v) << 28) & BM_CLKCTRL_PLL0CTRL0_LFR_SEL)
+#define BV_CLKCTRL_PLL0CTRL0_LFR_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLL0CTRL0_LFR_SEL__TIMES_2   0x1
+#define BV_CLKCTRL_PLL0CTRL0_LFR_SEL__TIMES_05  0x2
+#define BV_CLKCTRL_PLL0CTRL0_LFR_SEL__UNDEFINED 0x3
+#define BP_CLKCTRL_PLL0CTRL0_RSRVD5	26
+#define BM_CLKCTRL_PLL0CTRL0_RSRVD5	0x0C000000
+#define BF_CLKCTRL_PLL0CTRL0_RSRVD5(v)  \
+		(((v) << 26) & BM_CLKCTRL_PLL0CTRL0_RSRVD5)
+#define BP_CLKCTRL_PLL0CTRL0_CP_SEL	24
+#define BM_CLKCTRL_PLL0CTRL0_CP_SEL	0x03000000
+#define BF_CLKCTRL_PLL0CTRL0_CP_SEL(v)  \
+		(((v) << 24) & BM_CLKCTRL_PLL0CTRL0_CP_SEL)
+#define BV_CLKCTRL_PLL0CTRL0_CP_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLL0CTRL0_CP_SEL__TIMES_2   0x1
+#define BV_CLKCTRL_PLL0CTRL0_CP_SEL__TIMES_05  0x2
+#define BV_CLKCTRL_PLL0CTRL0_CP_SEL__UNDEFINED 0x3
+#define BP_CLKCTRL_PLL0CTRL0_RSRVD4	22
+#define BM_CLKCTRL_PLL0CTRL0_RSRVD4	0x00C00000
+#define BF_CLKCTRL_PLL0CTRL0_RSRVD4(v)  \
+		(((v) << 22) & BM_CLKCTRL_PLL0CTRL0_RSRVD4)
+#define BP_CLKCTRL_PLL0CTRL0_DIV_SEL	20
+#define BM_CLKCTRL_PLL0CTRL0_DIV_SEL	0x00300000
+#define BF_CLKCTRL_PLL0CTRL0_DIV_SEL(v)  \
+		(((v) << 20) & BM_CLKCTRL_PLL0CTRL0_DIV_SEL)
+#define BV_CLKCTRL_PLL0CTRL0_DIV_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLL0CTRL0_DIV_SEL__LOWER     0x1
+#define BV_CLKCTRL_PLL0CTRL0_DIV_SEL__LOWEST    0x2
+#define BV_CLKCTRL_PLL0CTRL0_DIV_SEL__UNDEFINED 0x3
+#define BM_CLKCTRL_PLL0CTRL0_RSRVD3	0x00080000
+#define BM_CLKCTRL_PLL0CTRL0_EN_USB_CLKS	0x00040000
+#define BM_CLKCTRL_PLL0CTRL0_POWER	0x00020000
+#define BP_CLKCTRL_PLL0CTRL0_RSRVD1	0
+#define BM_CLKCTRL_PLL0CTRL0_RSRVD1	0x0001FFFF
+#define BF_CLKCTRL_PLL0CTRL0_RSRVD1(v)  \
+		(((v) << 0) & BM_CLKCTRL_PLL0CTRL0_RSRVD1)
+
+#define HW_CLKCTRL_PLL0CTRL1	(0x00000010)
+
+#define BM_CLKCTRL_PLL0CTRL1_LOCK	0x80000000
+#define BM_CLKCTRL_PLL0CTRL1_FORCE_LOCK	0x40000000
+#define BP_CLKCTRL_PLL0CTRL1_RSRVD1	16
+#define BM_CLKCTRL_PLL0CTRL1_RSRVD1	0x3FFF0000
+#define BF_CLKCTRL_PLL0CTRL1_RSRVD1(v)  \
+		(((v) << 16) & BM_CLKCTRL_PLL0CTRL1_RSRVD1)
+#define BP_CLKCTRL_PLL0CTRL1_LOCK_COUNT	0
+#define BM_CLKCTRL_PLL0CTRL1_LOCK_COUNT	0x0000FFFF
+#define BF_CLKCTRL_PLL0CTRL1_LOCK_COUNT(v)  \
+		(((v) << 0) & BM_CLKCTRL_PLL0CTRL1_LOCK_COUNT)
+
+#define HW_CLKCTRL_PLL1CTRL0	(0x00000020)
+#define HW_CLKCTRL_PLL1CTRL0_SET	(0x00000024)
+#define HW_CLKCTRL_PLL1CTRL0_CLR	(0x00000028)
+#define HW_CLKCTRL_PLL1CTRL0_TOG	(0x0000002c)
+
+#define BM_CLKCTRL_PLL1CTRL0_CLKGATEEMI	0x80000000
+#define BM_CLKCTRL_PLL1CTRL0_RSRVD6	0x40000000
+#define BP_CLKCTRL_PLL1CTRL0_LFR_SEL	28
+#define BM_CLKCTRL_PLL1CTRL0_LFR_SEL	0x30000000
+#define BF_CLKCTRL_PLL1CTRL0_LFR_SEL(v)  \
+		(((v) << 28) & BM_CLKCTRL_PLL1CTRL0_LFR_SEL)
+#define BV_CLKCTRL_PLL1CTRL0_LFR_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLL1CTRL0_LFR_SEL__TIMES_2   0x1
+#define BV_CLKCTRL_PLL1CTRL0_LFR_SEL__TIMES_05  0x2
+#define BV_CLKCTRL_PLL1CTRL0_LFR_SEL__UNDEFINED 0x3
+#define BP_CLKCTRL_PLL1CTRL0_RSRVD5	26
+#define BM_CLKCTRL_PLL1CTRL0_RSRVD5	0x0C000000
+#define BF_CLKCTRL_PLL1CTRL0_RSRVD5(v)  \
+		(((v) << 26) & BM_CLKCTRL_PLL1CTRL0_RSRVD5)
+#define BP_CLKCTRL_PLL1CTRL0_CP_SEL	24
+#define BM_CLKCTRL_PLL1CTRL0_CP_SEL	0x03000000
+#define BF_CLKCTRL_PLL1CTRL0_CP_SEL(v)  \
+		(((v) << 24) & BM_CLKCTRL_PLL1CTRL0_CP_SEL)
+#define BV_CLKCTRL_PLL1CTRL0_CP_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLL1CTRL0_CP_SEL__TIMES_2   0x1
+#define BV_CLKCTRL_PLL1CTRL0_CP_SEL__TIMES_05  0x2
+#define BV_CLKCTRL_PLL1CTRL0_CP_SEL__UNDEFINED 0x3
+#define BP_CLKCTRL_PLL1CTRL0_RSRVD4	22
+#define BM_CLKCTRL_PLL1CTRL0_RSRVD4	0x00C00000
+#define BF_CLKCTRL_PLL1CTRL0_RSRVD4(v)  \
+		(((v) << 22) & BM_CLKCTRL_PLL1CTRL0_RSRVD4)
+#define BP_CLKCTRL_PLL1CTRL0_DIV_SEL	20
+#define BM_CLKCTRL_PLL1CTRL0_DIV_SEL	0x00300000
+#define BF_CLKCTRL_PLL1CTRL0_DIV_SEL(v)  \
+		(((v) << 20) & BM_CLKCTRL_PLL1CTRL0_DIV_SEL)
+#define BV_CLKCTRL_PLL1CTRL0_DIV_SEL__DEFAULT   0x0
+#define BV_CLKCTRL_PLL1CTRL0_DIV_SEL__LOWER     0x1
+#define BV_CLKCTRL_PLL1CTRL0_DIV_SEL__LOWEST    0x2
+#define BV_CLKCTRL_PLL1CTRL0_DIV_SEL__UNDEFINED 0x3
+#define BM_CLKCTRL_PLL1CTRL0_RSRVD3	0x00080000
+#define BM_CLKCTRL_PLL1CTRL0_EN_USB_CLKS	0x00040000
+#define BM_CLKCTRL_PLL1CTRL0_POWER	0x00020000
+#define BP_CLKCTRL_PLL1CTRL0_RSRVD1	0
+#define BM_CLKCTRL_PLL1CTRL0_RSRVD1	0x0001FFFF
+#define BF_CLKCTRL_PLL1CTRL0_RSRVD1(v)  \
+		(((v) << 0) & BM_CLKCTRL_PLL1CTRL0_RSRVD1)
+
+#define HW_CLKCTRL_PLL1CTRL1	(0x00000030)
+
+#define BM_CLKCTRL_PLL1CTRL1_LOCK	0x80000000
+#define BM_CLKCTRL_PLL1CTRL1_FORCE_LOCK	0x40000000
+#define BP_CLKCTRL_PLL1CTRL1_RSRVD1	16
+#define BM_CLKCTRL_PLL1CTRL1_RSRVD1	0x3FFF0000
+#define BF_CLKCTRL_PLL1CTRL1_RSRVD1(v)  \
+		(((v) << 16) & BM_CLKCTRL_PLL1CTRL1_RSRVD1)
+#define BP_CLKCTRL_PLL1CTRL1_LOCK_COUNT	0
+#define BM_CLKCTRL_PLL1CTRL1_LOCK_COUNT	0x0000FFFF
+#define BF_CLKCTRL_PLL1CTRL1_LOCK_COUNT(v)  \
+		(((v) << 0) & BM_CLKCTRL_PLL1CTRL1_LOCK_COUNT)
+
+#define HW_CLKCTRL_PLL2CTRL0	(0x00000040)
+#define HW_CLKCTRL_PLL2CTRL0_SET	(0x00000044)
+#define HW_CLKCTRL_PLL2CTRL0_CLR	(0x00000048)
+#define HW_CLKCTRL_PLL2CTRL0_TOG	(0x0000004c)
+
+#define BM_CLKCTRL_PLL2CTRL0_CLKGATE	0x80000000
+#define BM_CLKCTRL_PLL2CTRL0_RSRVD3	0x40000000
+#define BP_CLKCTRL_PLL2CTRL0_LFR_SEL	28
+#define BM_CLKCTRL_PLL2CTRL0_LFR_SEL	0x30000000
+#define BF_CLKCTRL_PLL2CTRL0_LFR_SEL(v)  \
+		(((v) << 28) & BM_CLKCTRL_PLL2CTRL0_LFR_SEL)
+#define BM_CLKCTRL_PLL2CTRL0_RSRVD2	0x08000000
+#define BM_CLKCTRL_PLL2CTRL0_HOLD_RING_OFF_B	0x04000000
+#define BP_CLKCTRL_PLL2CTRL0_CP_SEL	24
+#define BM_CLKCTRL_PLL2CTRL0_CP_SEL	0x03000000
+#define BF_CLKCTRL_PLL2CTRL0_CP_SEL(v)  \
+		(((v) << 24) & BM_CLKCTRL_PLL2CTRL0_CP_SEL)
+#define BM_CLKCTRL_PLL2CTRL0_POWER	0x00800000
+#define BP_CLKCTRL_PLL2CTRL0_RSRVD1	0
+#define BM_CLKCTRL_PLL2CTRL0_RSRVD1	0x007FFFFF
+#define BF_CLKCTRL_PLL2CTRL0_RSRVD1(v)  \
+		(((v) << 0) & BM_CLKCTRL_PLL2CTRL0_RSRVD1)
+
+#define HW_CLKCTRL_CPU	(0x00000050)
+#define HW_CLKCTRL_CPU_SET	(0x00000054)
+#define HW_CLKCTRL_CPU_CLR	(0x00000058)
+#define HW_CLKCTRL_CPU_TOG	(0x0000005c)
+
+#define BP_CLKCTRL_CPU_RSRVD5	30
+#define BM_CLKCTRL_CPU_RSRVD5	0xC0000000
+#define BF_CLKCTRL_CPU_RSRVD5(v) \
+		(((v) << 30) & BM_CLKCTRL_CPU_RSRVD5)
+#define BM_CLKCTRL_CPU_BUSY_REF_XTAL	0x20000000
+#define BM_CLKCTRL_CPU_BUSY_REF_CPU	0x10000000
+#define BM_CLKCTRL_CPU_RSRVD4	0x08000000
+#define BM_CLKCTRL_CPU_DIV_XTAL_FRAC_EN	0x04000000
+#define BP_CLKCTRL_CPU_DIV_XTAL	16
+#define BM_CLKCTRL_CPU_DIV_XTAL	0x03FF0000
+#define BF_CLKCTRL_CPU_DIV_XTAL(v)  \
+		(((v) << 16) & BM_CLKCTRL_CPU_DIV_XTAL)
+#define BP_CLKCTRL_CPU_RSRVD3	13
+#define BM_CLKCTRL_CPU_RSRVD3	0x0000E000
+#define BF_CLKCTRL_CPU_RSRVD3(v)  \
+		(((v) << 13) & BM_CLKCTRL_CPU_RSRVD3)
+#define BM_CLKCTRL_CPU_INTERRUPT_WAIT	0x00001000
+#define BM_CLKCTRL_CPU_RSRVD2	0x00000800
+#define BM_CLKCTRL_CPU_DIV_CPU_FRAC_EN	0x00000400
+#define BP_CLKCTRL_CPU_RSRVD1	6
+#define BM_CLKCTRL_CPU_RSRVD1	0x000003C0
+#define BF_CLKCTRL_CPU_RSRVD1(v)  \
+		(((v) << 6) & BM_CLKCTRL_CPU_RSRVD1)
+#define BP_CLKCTRL_CPU_DIV_CPU	0
+#define BM_CLKCTRL_CPU_DIV_CPU	0x0000003F
+#define BF_CLKCTRL_CPU_DIV_CPU(v)  \
+		(((v) << 0) & BM_CLKCTRL_CPU_DIV_CPU)
+
+#define HW_CLKCTRL_HBUS	(0x00000060)
+#define HW_CLKCTRL_HBUS_SET	(0x00000064)
+#define HW_CLKCTRL_HBUS_CLR	(0x00000068)
+#define HW_CLKCTRL_HBUS_TOG	(0x0000006c)
+
+#define BM_CLKCTRL_HBUS_ASM_BUSY	0x80000000
+#define BM_CLKCTRL_HBUS_DCP_AS_ENABLE	0x40000000
+#define BM_CLKCTRL_HBUS_PXP_AS_ENABLE	0x20000000
+#define BM_CLKCTRL_HBUS_RSRVD2	0x10000000
+#define BM_CLKCTRL_HBUS_ASM_EMIPORT_AS_ENABLE	0x08000000
+#define BM_CLKCTRL_HBUS_APBHDMA_AS_ENABLE	0x04000000
+#define BM_CLKCTRL_HBUS_APBXDMA_AS_ENABLE	0x02000000
+#define BM_CLKCTRL_HBUS_TRAFFIC_JAM_AS_ENABLE	0x01000000
+#define BM_CLKCTRL_HBUS_TRAFFIC_AS_ENABLE	0x00800000
+#define BM_CLKCTRL_HBUS_CPU_DATA_AS_ENABLE	0x00400000
+#define BM_CLKCTRL_HBUS_CPU_INSTR_AS_ENABLE	0x00200000
+#define BM_CLKCTRL_HBUS_ASM_ENABLE	0x00100000
+#define BM_CLKCTRL_HBUS_AUTO_CLEAR_DIV_ENABLE	0x00080000
+#define BP_CLKCTRL_HBUS_SLOW_DIV	16
+#define BM_CLKCTRL_HBUS_SLOW_DIV	0x00070000
+#define BF_CLKCTRL_HBUS_SLOW_DIV(v)  \
+		(((v) << 16) & BM_CLKCTRL_HBUS_SLOW_DIV)
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY1  0x0
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY2  0x1
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY4  0x2
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY8  0x3
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY16 0x4
+#define BV_CLKCTRL_HBUS_SLOW_DIV__BY32 0x5
+#define BP_CLKCTRL_HBUS_RSRVD1	6
+#define BM_CLKCTRL_HBUS_RSRVD1	0x0000FFC0
+#define BF_CLKCTRL_HBUS_RSRVD1(v)  \
+		(((v) << 6) & BM_CLKCTRL_HBUS_RSRVD1)
+#define BM_CLKCTRL_HBUS_DIV_FRAC_EN	0x00000020
+#define BP_CLKCTRL_HBUS_DIV	0
+#define BM_CLKCTRL_HBUS_DIV	0x0000001F
+#define BF_CLKCTRL_HBUS_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_HBUS_DIV)
+
+#define HW_CLKCTRL_XBUS	(0x00000070)
+
+#define BM_CLKCTRL_XBUS_BUSY	0x80000000
+#define BP_CLKCTRL_XBUS_RSRVD1	12
+#define BM_CLKCTRL_XBUS_RSRVD1	0x7FFFF000
+#define BF_CLKCTRL_XBUS_RSRVD1(v)  \
+		(((v) << 12) & BM_CLKCTRL_XBUS_RSRVD1)
+#define BM_CLKCTRL_XBUS_AUTO_CLEAR_DIV_ENABLE	0x00000800
+#define BM_CLKCTRL_XBUS_DIV_FRAC_EN	0x00000400
+#define BP_CLKCTRL_XBUS_DIV	0
+#define BM_CLKCTRL_XBUS_DIV	0x000003FF
+#define BF_CLKCTRL_XBUS_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_XBUS_DIV)
+
+#define HW_CLKCTRL_XTAL	(0x00000080)
+#define HW_CLKCTRL_XTAL_SET	(0x00000084)
+#define HW_CLKCTRL_XTAL_CLR	(0x00000088)
+#define HW_CLKCTRL_XTAL_TOG	(0x0000008c)
+
+#define BP_CLKCTRL_XTAL_UART_CLK_GATE	31
+#define BM_CLKCTRL_XTAL_UART_CLK_GATE	0x80000000
+#define BM_CLKCTRL_XTAL_RSRVD3	0x40000000
+#define BP_CLKCTRL_XTAL_PWM_CLK24M_GATE	29
+#define BM_CLKCTRL_XTAL_PWM_CLK24M_GATE	0x20000000
+#define BP_CLKCTRL_XTAL_RSRVD2	27
+#define BM_CLKCTRL_XTAL_RSRVD2	0x18000000
+#define BF_CLKCTRL_XTAL_RSRVD2(v)  \
+		(((v) << 27) & BM_CLKCTRL_XTAL_RSRVD2)
+#define BP_CLKCTRL_XTAL_TIMROT_CLK32K_GATE	26
+#define BM_CLKCTRL_XTAL_TIMROT_CLK32K_GATE	0x04000000
+#define BP_CLKCTRL_XTAL_RSRVD1	2
+#define BM_CLKCTRL_XTAL_RSRVD1	0x03FFFFFC
+#define BF_CLKCTRL_XTAL_RSRVD1(v)  \
+		(((v) << 2) & BM_CLKCTRL_XTAL_RSRVD1)
+#define BP_CLKCTRL_XTAL_DIV_UART	0
+#define BM_CLKCTRL_XTAL_DIV_UART	0x00000003
+#define BF_CLKCTRL_XTAL_DIV_UART(v)  \
+		(((v) << 0) & BM_CLKCTRL_XTAL_DIV_UART)
+
+#define HW_CLKCTRL_SSP0	(0x00000090)
+
+#define BP_CLKCTRL_SSP0_CLKGATE	31
+#define BM_CLKCTRL_SSP0_CLKGATE	0x80000000
+#define BM_CLKCTRL_SSP0_RSRVD2	0x40000000
+#define BM_CLKCTRL_SSP0_BUSY	0x20000000
+#define BP_CLKCTRL_SSP0_RSRVD1	10
+#define BM_CLKCTRL_SSP0_RSRVD1	0x1FFFFC00
+#define BF_CLKCTRL_SSP0_RSRVD1(v)  \
+		(((v) << 10) & BM_CLKCTRL_SSP0_RSRVD1)
+#define BM_CLKCTRL_SSP0_DIV_FRAC_EN	0x00000200
+#define BP_CLKCTRL_SSP0_DIV	0
+#define BM_CLKCTRL_SSP0_DIV	0x000001FF
+#define BF_CLKCTRL_SSP0_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_SSP0_DIV)
+
+#define HW_CLKCTRL_SSP1	(0x000000a0)
+
+#define BP_CLKCTRL_SSP1_CLKGATE	31
+#define BM_CLKCTRL_SSP1_CLKGATE	0x80000000
+#define BM_CLKCTRL_SSP1_RSRVD2	0x40000000
+#define BM_CLKCTRL_SSP1_BUSY	0x20000000
+#define BP_CLKCTRL_SSP1_RSRVD1	10
+#define BM_CLKCTRL_SSP1_RSRVD1	0x1FFFFC00
+#define BF_CLKCTRL_SSP1_RSRVD1(v)  \
+		(((v) << 10) & BM_CLKCTRL_SSP1_RSRVD1)
+#define BM_CLKCTRL_SSP1_DIV_FRAC_EN	0x00000200
+#define BP_CLKCTRL_SSP1_DIV	0
+#define BM_CLKCTRL_SSP1_DIV	0x000001FF
+#define BF_CLKCTRL_SSP1_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_SSP1_DIV)
+
+#define HW_CLKCTRL_SSP2	(0x000000b0)
+
+#define BP_CLKCTRL_SSP2_CLKGATE	31
+#define BM_CLKCTRL_SSP2_CLKGATE	0x80000000
+#define BM_CLKCTRL_SSP2_RSRVD2	0x40000000
+#define BM_CLKCTRL_SSP2_BUSY	0x20000000
+#define BP_CLKCTRL_SSP2_RSRVD1	10
+#define BM_CLKCTRL_SSP2_RSRVD1	0x1FFFFC00
+#define BF_CLKCTRL_SSP2_RSRVD1(v)  \
+		(((v) << 10) & BM_CLKCTRL_SSP2_RSRVD1)
+#define BM_CLKCTRL_SSP2_DIV_FRAC_EN	0x00000200
+#define BP_CLKCTRL_SSP2_DIV	0
+#define BM_CLKCTRL_SSP2_DIV	0x000001FF
+#define BF_CLKCTRL_SSP2_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_SSP2_DIV)
+
+#define HW_CLKCTRL_SSP3	(0x000000c0)
+
+#define BP_CLKCTRL_SSP3_CLKGATE	31
+#define BM_CLKCTRL_SSP3_CLKGATE	0x80000000
+#define BM_CLKCTRL_SSP3_RSRVD2	0x40000000
+#define BM_CLKCTRL_SSP3_BUSY	0x20000000
+#define BP_CLKCTRL_SSP3_RSRVD1	10
+#define BM_CLKCTRL_SSP3_RSRVD1	0x1FFFFC00
+#define BF_CLKCTRL_SSP3_RSRVD1(v)  \
+		(((v) << 10) & BM_CLKCTRL_SSP3_RSRVD1)
+#define BM_CLKCTRL_SSP3_DIV_FRAC_EN	0x00000200
+#define BP_CLKCTRL_SSP3_DIV	0
+#define BM_CLKCTRL_SSP3_DIV	0x000001FF
+#define BF_CLKCTRL_SSP3_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_SSP3_DIV)
+
+#define HW_CLKCTRL_GPMI	(0x000000d0)
+
+#define BP_CLKCTRL_GPMI_CLKGATE	31
+#define BM_CLKCTRL_GPMI_CLKGATE	0x80000000
+#define BM_CLKCTRL_GPMI_RSRVD2	0x40000000
+#define BM_CLKCTRL_GPMI_BUSY	0x20000000
+#define BP_CLKCTRL_GPMI_RSRVD1	11
+#define BM_CLKCTRL_GPMI_RSRVD1	0x1FFFF800
+#define BF_CLKCTRL_GPMI_RSRVD1(v)  \
+		(((v) << 11) & BM_CLKCTRL_GPMI_RSRVD1)
+#define BM_CLKCTRL_GPMI_DIV_FRAC_EN	0x00000400
+#define BP_CLKCTRL_GPMI_DIV	0
+#define BM_CLKCTRL_GPMI_DIV	0x000003FF
+#define BF_CLKCTRL_GPMI_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_GPMI_DIV)
+
+#define HW_CLKCTRL_SPDIF	(0x000000e0)
+
+#define BP_CLKCTRL_SPDIF_CLKGATE	31
+#define BM_CLKCTRL_SPDIF_CLKGATE	0x80000000
+#define BP_CLKCTRL_SPDIF_RSRVD	0
+#define BM_CLKCTRL_SPDIF_RSRVD	0x7FFFFFFF
+#define BF_CLKCTRL_SPDIF_RSRVD(v)  \
+		(((v) << 0) & BM_CLKCTRL_SPDIF_RSRVD)
+
+#define HW_CLKCTRL_EMI	(0x000000f0)
+
+#define BP_CLKCTRL_EMI_CLKGATE	31
+#define BM_CLKCTRL_EMI_CLKGATE	0x80000000
+#define BM_CLKCTRL_EMI_SYNC_MODE_EN	0x40000000
+#define BM_CLKCTRL_EMI_BUSY_REF_XTAL	0x20000000
+#define BM_CLKCTRL_EMI_BUSY_REF_EMI	0x10000000
+#define BM_CLKCTRL_EMI_BUSY_REF_CPU	0x08000000
+#define BM_CLKCTRL_EMI_BUSY_SYNC_MODE	0x04000000
+#define BP_CLKCTRL_EMI_RSRVD3	18
+#define BM_CLKCTRL_EMI_RSRVD3	0x03FC0000
+#define BF_CLKCTRL_EMI_RSRVD3(v)  \
+		(((v) << 18) & BM_CLKCTRL_EMI_RSRVD3)
+#define BM_CLKCTRL_EMI_BUSY_DCC_RESYNC	0x00020000
+#define BM_CLKCTRL_EMI_DCC_RESYNC_ENABLE	0x00010000
+#define BP_CLKCTRL_EMI_RSRVD2	12
+#define BM_CLKCTRL_EMI_RSRVD2	0x0000F000
+#define BF_CLKCTRL_EMI_RSRVD2(v)  \
+		(((v) << 12) & BM_CLKCTRL_EMI_RSRVD2)
+#define BP_CLKCTRL_EMI_DIV_XTAL	8
+#define BM_CLKCTRL_EMI_DIV_XTAL	0x00000F00
+#define BF_CLKCTRL_EMI_DIV_XTAL(v)  \
+		(((v) << 8) & BM_CLKCTRL_EMI_DIV_XTAL)
+#define BP_CLKCTRL_EMI_RSRVD1	6
+#define BM_CLKCTRL_EMI_RSRVD1	0x000000C0
+#define BF_CLKCTRL_EMI_RSRVD1(v)  \
+		(((v) << 6) & BM_CLKCTRL_EMI_RSRVD1)
+#define BP_CLKCTRL_EMI_DIV_EMI	0
+#define BM_CLKCTRL_EMI_DIV_EMI	0x0000003F
+#define BF_CLKCTRL_EMI_DIV_EMI(v)  \
+		(((v) << 0) & BM_CLKCTRL_EMI_DIV_EMI)
+
+#define HW_CLKCTRL_SAIF0	(0x00000100)
+
+#define BP_CLKCTRL_SAIF0_CLKGATE	31
+#define BM_CLKCTRL_SAIF0_CLKGATE	0x80000000
+#define BM_CLKCTRL_SAIF0_RSRVD2	0x40000000
+#define BM_CLKCTRL_SAIF0_BUSY	0x20000000
+#define BP_CLKCTRL_SAIF0_RSRVD1	17
+#define BM_CLKCTRL_SAIF0_RSRVD1	0x1FFE0000
+#define BF_CLKCTRL_SAIF0_RSRVD1(v)  \
+		(((v) << 17) & BM_CLKCTRL_SAIF0_RSRVD1)
+#define BM_CLKCTRL_SAIF0_DIV_FRAC_EN	0x00010000
+#define BP_CLKCTRL_SAIF0_DIV	0
+#define BM_CLKCTRL_SAIF0_DIV	0x0000FFFF
+#define BF_CLKCTRL_SAIF0_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_SAIF0_DIV)
+
+#define HW_CLKCTRL_SAIF1	(0x00000110)
+
+#define BP_CLKCTRL_SAIF1_CLKGATE	31
+#define BM_CLKCTRL_SAIF1_CLKGATE	0x80000000
+#define BM_CLKCTRL_SAIF1_RSRVD2	0x40000000
+#define BM_CLKCTRL_SAIF1_BUSY	0x20000000
+#define BP_CLKCTRL_SAIF1_RSRVD1	17
+#define BM_CLKCTRL_SAIF1_RSRVD1	0x1FFE0000
+#define BF_CLKCTRL_SAIF1_RSRVD1(v)  \
+		(((v) << 17) & BM_CLKCTRL_SAIF1_RSRVD1)
+#define BM_CLKCTRL_SAIF1_DIV_FRAC_EN	0x00010000
+#define BP_CLKCTRL_SAIF1_DIV	0
+#define BM_CLKCTRL_SAIF1_DIV	0x0000FFFF
+#define BF_CLKCTRL_SAIF1_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_SAIF1_DIV)
+
+#define HW_CLKCTRL_DIS_LCDIF	(0x00000120)
+
+#define BP_CLKCTRL_DIS_LCDIF_CLKGATE	31
+#define BM_CLKCTRL_DIS_LCDIF_CLKGATE	0x80000000
+#define BM_CLKCTRL_DIS_LCDIF_RSRVD2	0x40000000
+#define BM_CLKCTRL_DIS_LCDIF_BUSY	0x20000000
+#define BP_CLKCTRL_DIS_LCDIF_RSRVD1	14
+#define BM_CLKCTRL_DIS_LCDIF_RSRVD1	0x1FFFC000
+#define BF_CLKCTRL_DIS_LCDIF_RSRVD1(v)  \
+		(((v) << 14) & BM_CLKCTRL_DIS_LCDIF_RSRVD1)
+#define BM_CLKCTRL_DIS_LCDIF_DIV_FRAC_EN	0x00002000
+#define BP_CLKCTRL_DIS_LCDIF_DIV	0
+#define BM_CLKCTRL_DIS_LCDIF_DIV	0x00001FFF
+#define BF_CLKCTRL_DIS_LCDIF_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_DIS_LCDIF_DIV)
+
+#define HW_CLKCTRL_ETM	(0x00000130)
+
+#define BM_CLKCTRL_ETM_CLKGATE	0x80000000
+#define BM_CLKCTRL_ETM_RSRVD2	0x40000000
+#define BM_CLKCTRL_ETM_BUSY	0x20000000
+#define BP_CLKCTRL_ETM_RSRVD1	8
+#define BM_CLKCTRL_ETM_RSRVD1	0x1FFFFF00
+#define BF_CLKCTRL_ETM_RSRVD1(v)  \
+		(((v) << 8) & BM_CLKCTRL_ETM_RSRVD1)
+#define BM_CLKCTRL_ETM_DIV_FRAC_EN	0x00000080
+#define BP_CLKCTRL_ETM_DIV	0
+#define BM_CLKCTRL_ETM_DIV	0x0000007F
+#define BF_CLKCTRL_ETM_DIV(v)  \
+		(((v) << 0) & BM_CLKCTRL_ETM_DIV)
+
+#define HW_CLKCTRL_ENET	(0x00000140)
+
+#define BM_CLKCTRL_ENET_SLEEP	0x80000000
+#define BP_CLKCTRL_ENET_DISABLE	30
+#define BM_CLKCTRL_ENET_DISABLE	0x40000000
+#define BM_CLKCTRL_ENET_STATUS	0x20000000
+#define BM_CLKCTRL_ENET_RSRVD1	0x10000000
+#define BM_CLKCTRL_ENET_BUSY_TIME	0x08000000
+#define BP_CLKCTRL_ENET_DIV_TIME	21
+#define BM_CLKCTRL_ENET_DIV_TIME	0x07E00000
+#define BF_CLKCTRL_ENET_DIV_TIME(v)  \
+		(((v) << 21) & BM_CLKCTRL_ENET_DIV_TIME)
+#define BM_CLKCTRL_ENET_BUSY	0x08000000
+#define BP_CLKCTRL_ENET_DIV	21
+#define BM_CLKCTRL_ENET_DIV	0x07E00000
+#define BF_CLKCTRL_ENET_DIV(v)  \
+		(((v) << 21) & BM_CLKCTRL_ENET_DIV)
+#define BP_CLKCTRL_ENET_TIME_SEL	19
+#define BM_CLKCTRL_ENET_TIME_SEL	0x00180000
+#define BF_CLKCTRL_ENET_TIME_SEL(v)  \
+		(((v) << 19) & BM_CLKCTRL_ENET_TIME_SEL)
+#define BV_CLKCTRL_ENET_TIME_SEL__XTAL      0x0
+#define BV_CLKCTRL_ENET_TIME_SEL__PLL       0x1
+#define BV_CLKCTRL_ENET_TIME_SEL__RMII_CLK  0x2
+#define BV_CLKCTRL_ENET_TIME_SEL__UNDEFINED 0x3
+#define BM_CLKCTRL_ENET_CLK_OUT_EN	0x00040000
+#define BM_CLKCTRL_ENET_RESET_BY_SW_CHIP	0x00020000
+#define BM_CLKCTRL_ENET_RESET_BY_SW	0x00010000
+#define BP_CLKCTRL_ENET_RSRVD0	0
+#define BM_CLKCTRL_ENET_RSRVD0	0x0000FFFF
+#define BF_CLKCTRL_ENET_RSRVD0(v)  \
+		(((v) << 0) & BM_CLKCTRL_ENET_RSRVD0)
+
+#define HW_CLKCTRL_HSADC	(0x00000150)
+
+#define BM_CLKCTRL_HSADC_RSRVD2	0x80000000
+#define BM_CLKCTRL_HSADC_RESETB	0x40000000
+#define BP_CLKCTRL_HSADC_FREQDIV	28
+#define BM_CLKCTRL_HSADC_FREQDIV	0x30000000
+#define BF_CLKCTRL_HSADC_FREQDIV(v)  \
+		(((v) << 28) & BM_CLKCTRL_HSADC_FREQDIV)
+#define BP_CLKCTRL_HSADC_RSRVD1	0
+#define BM_CLKCTRL_HSADC_RSRVD1	0x0FFFFFFF
+#define BF_CLKCTRL_HSADC_RSRVD1(v)  \
+		(((v) << 0) & BM_CLKCTRL_HSADC_RSRVD1)
+
+#define HW_CLKCTRL_FLEXCAN	(0x00000160)
+
+#define BM_CLKCTRL_FLEXCAN_RSRVD2	0x80000000
+#define BP_CLKCTRL_FLEXCAN_STOP_CAN0	30
+#define BM_CLKCTRL_FLEXCAN_STOP_CAN0	0x40000000
+#define BM_CLKCTRL_FLEXCAN_CAN0_STATUS	0x20000000
+#define BP_CLKCTRL_FLEXCAN_STOP_CAN1	28
+#define BM_CLKCTRL_FLEXCAN_STOP_CAN1	0x10000000
+#define BM_CLKCTRL_FLEXCAN_CAN1_STATUS	0x08000000
+#define BP_CLKCTRL_FLEXCAN_RSRVD1	0
+#define BM_CLKCTRL_FLEXCAN_RSRVD1	0x07FFFFFF
+#define BF_CLKCTRL_FLEXCAN_RSRVD1(v)  \
+		(((v) << 0) & BM_CLKCTRL_FLEXCAN_RSRVD1)
+
+#define HW_CLKCTRL_FRAC0	(0x000001b0)
+#define HW_CLKCTRL_FRAC0_SET	(0x000001b4)
+#define HW_CLKCTRL_FRAC0_CLR	(0x000001b8)
+#define HW_CLKCTRL_FRAC0_TOG	(0x000001bc)
+
+#define BP_CLKCTRL_FRAC0_CLKGATEIO0	31
+#define BM_CLKCTRL_FRAC0_CLKGATEIO0	0x80000000
+#define BM_CLKCTRL_FRAC0_IO0_STABLE	0x40000000
+#define BP_CLKCTRL_FRAC0_IO0FRAC	24
+#define BM_CLKCTRL_FRAC0_IO0FRAC	0x3F000000
+#define BF_CLKCTRL_FRAC0_IO0FRAC(v)  \
+		(((v) << 24) & BM_CLKCTRL_FRAC0_IO0FRAC)
+#define BP_CLKCTRL_FRAC0_CLKGATEIO1	23
+#define BM_CLKCTRL_FRAC0_CLKGATEIO1	0x00800000
+#define BM_CLKCTRL_FRAC0_IO1_STABLE	0x00400000
+#define BP_CLKCTRL_FRAC0_IO1FRAC	16
+#define BM_CLKCTRL_FRAC0_IO1FRAC	0x003F0000
+#define BF_CLKCTRL_FRAC0_IO1FRAC(v)  \
+		(((v) << 16) & BM_CLKCTRL_FRAC0_IO1FRAC)
+#define BP_CLKCTRL_FRAC0_CLKGATEEMI	15
+#define BM_CLKCTRL_FRAC0_CLKGATEEMI	0x00008000
+#define BM_CLKCTRL_FRAC0_EMI_STABLE	0x00004000
+#define BP_CLKCTRL_FRAC0_EMIFRAC	8
+#define BM_CLKCTRL_FRAC0_EMIFRAC	0x00003F00
+#define BF_CLKCTRL_FRAC0_EMIFRAC(v)  \
+		(((v) << 8) & BM_CLKCTRL_FRAC0_EMIFRAC)
+#define BP_CLKCTRL_FRAC0_CLKGATECPU	7
+#define BM_CLKCTRL_FRAC0_CLKGATECPU	0x00000080
+#define BM_CLKCTRL_FRAC0_CPU_STABLE	0x00000040
+#define BP_CLKCTRL_FRAC0_CPUFRAC	0
+#define BM_CLKCTRL_FRAC0_CPUFRAC	0x0000003F
+#define BF_CLKCTRL_FRAC0_CPUFRAC(v)  \
+		(((v) << 0) & BM_CLKCTRL_FRAC0_CPUFRAC)
+
+#define HW_CLKCTRL_FRAC1	(0x000001c0)
+#define HW_CLKCTRL_FRAC1_SET	(0x000001c4)
+#define HW_CLKCTRL_FRAC1_CLR	(0x000001c8)
+#define HW_CLKCTRL_FRAC1_TOG	(0x000001cc)
+
+#define BP_CLKCTRL_FRAC1_RSRVD2	24
+#define BM_CLKCTRL_FRAC1_RSRVD2	0xFF000000
+#define BF_CLKCTRL_FRAC1_RSRVD2(v) \
+		(((v) << 24) & BM_CLKCTRL_FRAC1_RSRVD2)
+#define BP_CLKCTRL_FRAC1_CLKGATEGPMI	23
+#define BM_CLKCTRL_FRAC1_CLKGATEGPMI	0x00800000
+#define BM_CLKCTRL_FRAC1_GPMI_STABLE	0x00400000
+#define BP_CLKCTRL_FRAC1_GPMIFRAC	16
+#define BM_CLKCTRL_FRAC1_GPMIFRAC	0x003F0000
+#define BF_CLKCTRL_FRAC1_GPMIFRAC(v)  \
+		(((v) << 16) & BM_CLKCTRL_FRAC1_GPMIFRAC)
+#define BP_CLKCTRL_FRAC1_CLKGATEHSADC	15
+#define BM_CLKCTRL_FRAC1_CLKGATEHSADC	0x00008000
+#define BM_CLKCTRL_FRAC1_HSADC_STABLE	0x00004000
+#define BP_CLKCTRL_FRAC1_HSADCFRAC	8
+#define BM_CLKCTRL_FRAC1_HSADCFRAC	0x00003F00
+#define BF_CLKCTRL_FRAC1_HSADCFRAC(v)  \
+		(((v) << 8) & BM_CLKCTRL_FRAC1_HSADCFRAC)
+#define BP_CLKCTRL_FRAC1_CLKGATEPIX	7
+#define BM_CLKCTRL_FRAC1_CLKGATEPIX	0x00000080
+#define BM_CLKCTRL_FRAC1_PIX_STABLE	0x00000040
+#define BP_CLKCTRL_FRAC1_PIXFRAC	0
+#define BM_CLKCTRL_FRAC1_PIXFRAC	0x0000003F
+#define BF_CLKCTRL_FRAC1_PIXFRAC(v)  \
+		(((v) << 0) & BM_CLKCTRL_FRAC1_PIXFRAC)
+
+#define HW_CLKCTRL_CLKSEQ	(0x000001d0)
+#define HW_CLKCTRL_CLKSEQ_SET	(0x000001d4)
+#define HW_CLKCTRL_CLKSEQ_CLR	(0x000001d8)
+#define HW_CLKCTRL_CLKSEQ_TOG	(0x000001dc)
+
+#define BP_CLKCTRL_CLKSEQ_RSRVD0	19
+#define BM_CLKCTRL_CLKSEQ_RSRVD0	0xFFF80000
+#define BF_CLKCTRL_CLKSEQ_RSRVD0(v) \
+		(((v) << 19) & BM_CLKCTRL_CLKSEQ_RSRVD0)
+#define BM_CLKCTRL_CLKSEQ_BYPASS_CPU	0x00040000
+#define BP_CLKCTRL_CLKSEQ_RSRVD1	15
+#define BM_CLKCTRL_CLKSEQ_RSRVD1	0x00038000
+#define BF_CLKCTRL_CLKSEQ_RSRVD1(v)  \
+		(((v) << 15) & BM_CLKCTRL_CLKSEQ_RSRVD1)
+#define BM_CLKCTRL_CLKSEQ_BYPASS_DIS_LCDIF	0x00004000
+#define BV_CLKCTRL_CLKSEQ_BYPASS_DIS_LCDIF__BYPASS 0x1
+#define BV_CLKCTRL_CLKSEQ_BYPASS_DIS_LCDIF__PFD    0x0
+#define BP_CLKCTRL_CLKSEQ_RSRVD2	9
+#define BM_CLKCTRL_CLKSEQ_RSRVD2	0x00003E00
+#define BF_CLKCTRL_CLKSEQ_RSRVD2(v)  \
+		(((v) << 9) & BM_CLKCTRL_CLKSEQ_RSRVD2)
+#define BM_CLKCTRL_CLKSEQ_BYPASS_ETM	0x00000100
+#define BM_CLKCTRL_CLKSEQ_BYPASS_EMI	0x00000080
+#define BM_CLKCTRL_CLKSEQ_BYPASS_SSP3	0x00000040
+#define BM_CLKCTRL_CLKSEQ_BYPASS_SSP2	0x00000020
+#define BM_CLKCTRL_CLKSEQ_BYPASS_SSP1	0x00000010
+#define BM_CLKCTRL_CLKSEQ_BYPASS_SSP0	0x00000008
+#define BM_CLKCTRL_CLKSEQ_BYPASS_GPMI	0x00000004
+#define BM_CLKCTRL_CLKSEQ_BYPASS_SAIF1	0x00000002
+#define BM_CLKCTRL_CLKSEQ_BYPASS_SAIF0	0x00000001
+
+#define HW_CLKCTRL_RESET	(0x000001e0)
+
+#define BP_CLKCTRL_RESET_RSRVD	6
+#define BM_CLKCTRL_RESET_RSRVD	0xFFFFFFC0
+#define BF_CLKCTRL_RESET_RSRVD(v) \
+		(((v) << 6) & BM_CLKCTRL_RESET_RSRVD)
+#define BM_CLKCTRL_RESET_WDOG_POR_DISABLE	0x00000020
+#define BM_CLKCTRL_RESET_EXTERNAL_RESET_ENABLE	0x00000010
+#define BM_CLKCTRL_RESET_THERMAL_RESET_ENABLE	0x00000008
+#define BM_CLKCTRL_RESET_THERMAL_RESET_DEFAULT	0x00000004
+#define BM_CLKCTRL_RESET_CHIP	0x00000002
+#define BM_CLKCTRL_RESET_DIG	0x00000001
+
+#define HW_CLKCTRL_STATUS	(0x000001f0)
+
+#define BP_CLKCTRL_STATUS_CPU_LIMIT	30
+#define BM_CLKCTRL_STATUS_CPU_LIMIT	0xC0000000
+#define BF_CLKCTRL_STATUS_CPU_LIMIT(v) \
+		(((v) << 30) & BM_CLKCTRL_STATUS_CPU_LIMIT)
+#define BP_CLKCTRL_STATUS_RSRVD	0
+#define BM_CLKCTRL_STATUS_RSRVD	0x3FFFFFFF
+#define BF_CLKCTRL_STATUS_RSRVD(v)  \
+		(((v) << 0) & BM_CLKCTRL_STATUS_RSRVD)
+
+#define HW_CLKCTRL_VERSION	(0x00000200)
+
+#define BP_CLKCTRL_VERSION_MAJOR	24
+#define BM_CLKCTRL_VERSION_MAJOR	0xFF000000
+#define BF_CLKCTRL_VERSION_MAJOR(v) \
+		(((v) << 24) & BM_CLKCTRL_VERSION_MAJOR)
+#define BP_CLKCTRL_VERSION_MINOR	16
+#define BM_CLKCTRL_VERSION_MINOR	0x00FF0000
+#define BF_CLKCTRL_VERSION_MINOR(v)  \
+		(((v) << 16) & BM_CLKCTRL_VERSION_MINOR)
+#define BP_CLKCTRL_VERSION_STEP	0
+#define BM_CLKCTRL_VERSION_STEP	0x0000FFFF
+#define BF_CLKCTRL_VERSION_STEP(v)  \
+		(((v) << 0) & BM_CLKCTRL_VERSION_STEP)
+
+#endif /* __REGS_CLKCTRL_MX28_H__ */
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v7 13/15] ARM: mxs: Add initial mx23evk support
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
                   ` (6 preceding siblings ...)
  2010-12-18 13:39 ` [PATCH v7 09/15] ARM: mxs: Add clock support Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  2010-12-20  9:48   ` Uwe Kleine-König
  2010-12-18 13:39 ` [PATCH v7 14/15] ARM: mxs: Add initial mx28evk support Shawn Guo
  8 siblings, 1 reply; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

Add initial mx23evk support with duart.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Changes for v7:
 - Define mx23evk pads using naked pad "OR" mA/vol/pull configurations

Changes for v3:
 - Remove inclusion of hardware.h
 - Add __initconst for mx23evk_pads[]

Changes for v2:
 - Remove boot_params

 arch/arm/mach-mxs/mach-mx23evk.c |   59 ++++++++++++++++++++++++++++++++++++++
 1 files changed, 59 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/mach-mx23evk.c

diff --git a/arch/arm/mach-mxs/mach-mx23evk.c b/arch/arm/mach-mxs/mach-mx23evk.c
new file mode 100644
index 0000000..2aa77cc
--- /dev/null
+++ b/arch/arm/mach-mxs/mach-mx23evk.c
@@ -0,0 +1,59 @@
+/*
+ * Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include <mach/common.h>
+#include <mach/iomux-mx23.h>
+
+#include "devices-mx23.h"
+
+static const iomux_cfg_t mx23evk_pads[] __initconst = {
+	/* duart */
+	MX23_PAD_PWM0__DUART_RX |
+		MXS_PAD_4MA,
+	MX23_PAD_PWM1__DUART_TX |
+		MXS_PAD_4MA,
+};
+
+static void __init mx23evk_init(void)
+{
+	mxs_iomux_setup_multiple_pads(mx23evk_pads, ARRAY_SIZE(mx23evk_pads));
+
+	mx23_add_duart();
+}
+
+static void __init mx23evk_timer_init(void)
+{
+	mx23_clocks_init();
+}
+
+static struct sys_timer mx23evk_timer = {
+	.init	= mx23evk_timer_init,
+};
+
+MACHINE_START(MX23EVK, "Freescale MX23 EVK")
+	/* Maintainer: Freescale Semiconductor, Inc. */
+	.map_io		= mx23_map_io,
+	.init_irq	= mx23_init_irq,
+	.init_machine	= mx23evk_init,
+	.timer		= &mx23evk_timer,
+MACHINE_END
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v7 13/15] ARM: mxs: Add initial mx23evk support
  2010-12-18 13:39 ` [PATCH v7 13/15] ARM: mxs: Add initial mx23evk support Shawn Guo
@ 2010-12-20  9:48   ` Uwe Kleine-König
  2010-12-20 10:17     ` Shawn Guo
  0 siblings, 1 reply; 18+ messages in thread
From: Uwe Kleine-König @ 2010-12-20  9:48 UTC (permalink / raw)
  To: linux-arm-kernel

Hello Shawn,

On Sat, Dec 18, 2010 at 09:39:34PM +0800, Shawn Guo wrote:
> Add initial mx23evk support with duart.
> 
> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
> ---
> Changes for v7:
>  - Define mx23evk pads using naked pad "OR" mA/vol/pull configurations
> 
> Changes for v3:
>  - Remove inclusion of hardware.h
>  - Add __initconst for mx23evk_pads[]
> 
> Changes for v2:
>  - Remove boot_params
> 
>  arch/arm/mach-mxs/mach-mx23evk.c |   59 ++++++++++++++++++++++++++++++++++++++
>  1 files changed, 59 insertions(+), 0 deletions(-)
>  create mode 100644 arch/arm/mach-mxs/mach-mx23evk.c
> 
> diff --git a/arch/arm/mach-mxs/mach-mx23evk.c b/arch/arm/mach-mxs/mach-mx23evk.c
> new file mode 100644
> index 0000000..2aa77cc
> --- /dev/null
> +++ b/arch/arm/mach-mxs/mach-mx23evk.c
> @@ -0,0 +1,59 @@
> [...]
> +static const iomux_cfg_t mx23evk_pads[] __initconst = {
> +	/* duart */
> +	MX23_PAD_PWM0__DUART_RX |
> +		MXS_PAD_4MA,
> +	MX23_PAD_PWM1__DUART_TX |
> +		MXS_PAD_4MA,
> +};
I would keep these on a single line.  YMMV, so for me no need for a v8.

I will test this series later on hardware, and if no show stoppers
appear I'd say this is ready to be merged.  The (maybe) remaining issues
can then be resolved in follow up patches.

Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 13/15] ARM: mxs: Add initial mx23evk support
  2010-12-20  9:48   ` Uwe Kleine-König
@ 2010-12-20 10:17     ` Shawn Guo
  0 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2010-12-20 10:17 UTC (permalink / raw)
  To: linux-arm-kernel

Hi Uwe,

On Mon, Dec 20, 2010 at 10:48:01AM +0100, Uwe Kleine-K?nig wrote:
> Hello Shawn,
> 
> On Sat, Dec 18, 2010 at 09:39:34PM +0800, Shawn Guo wrote:
> > Add initial mx23evk support with duart.
> > 
> > Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
> > ---
> > Changes for v7:
> >  - Define mx23evk pads using naked pad "OR" mA/vol/pull configurations
> > 
> > Changes for v3:
> >  - Remove inclusion of hardware.h
> >  - Add __initconst for mx23evk_pads[]
> > 
> > Changes for v2:
> >  - Remove boot_params
> > 
> >  arch/arm/mach-mxs/mach-mx23evk.c |   59 ++++++++++++++++++++++++++++++++++++++
> >  1 files changed, 59 insertions(+), 0 deletions(-)
> >  create mode 100644 arch/arm/mach-mxs/mach-mx23evk.c
> > 
> > diff --git a/arch/arm/mach-mxs/mach-mx23evk.c b/arch/arm/mach-mxs/mach-mx23evk.c
> > new file mode 100644
> > index 0000000..2aa77cc
> > --- /dev/null
> > +++ b/arch/arm/mach-mxs/mach-mx23evk.c
> > @@ -0,0 +1,59 @@
> > [...]
> > +static const iomux_cfg_t mx23evk_pads[] __initconst = {
> > +	/* duart */
> > +	MX23_PAD_PWM0__DUART_RX |
> > +		MXS_PAD_4MA,
> > +	MX23_PAD_PWM1__DUART_TX |
> > +		MXS_PAD_4MA,
> > +};
> I would keep these on a single line.  YMMV, so for me no need for a v8.
> 
> I will test this series later on hardware, and if no show stoppers
> appear I'd say this is ready to be merged.  The (maybe) remaining issues
> can then be resolved in follow up patches.
> 
My intension was to keep the pad configuration on different line from
the naked pad.  I will keep this comment and that extra space one
in mind, and address them later.

Thanks for the review and test effort. 

-- 
Regards,
Shawn

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v7 14/15] ARM: mxs: Add initial mx28evk support
  2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
                   ` (7 preceding siblings ...)
  2010-12-18 13:39 ` [PATCH v7 13/15] ARM: mxs: Add initial mx23evk support Shawn Guo
@ 2010-12-18 13:39 ` Shawn Guo
  8 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2010-12-18 13:39 UTC (permalink / raw)
  To: linux-arm-kernel

Add initial mx28evk support with duart and fec0.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
---
Changes for v7:
 - Define mx28evk pads using naked pad "OR" mA/vol/pull configurations

Changes for v3:
 - Remove inclusion of hardware.h
 - Add __initconst for mx28evk_pads[]

Changes for v2:
 - Change function mx28evk_fec_reset() from inline to __init
 - Enable pll2 clock before phy operation
 - Add error checking for gpio_direction_output()
 - Save bytes by passing parameter into pr_err format string
 - Change mx28_add_fec0() to mx28_add_fec(0)
 - Remove boot_params

 arch/arm/mach-mxs/mach-mx28evk.c |  138 ++++++++++++++++++++++++++++++++++++++
 1 files changed, 138 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/mach-mx28evk.c

diff --git a/arch/arm/mach-mxs/mach-mx28evk.c b/arch/arm/mach-mxs/mach-mx28evk.c
new file mode 100644
index 0000000..d162e95
--- /dev/null
+++ b/arch/arm/mach-mxs/mach-mx28evk.c
@@ -0,0 +1,138 @@
+/*
+ * Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/clk.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include <mach/common.h>
+#include <mach/iomux-mx28.h>
+
+#include "devices-mx28.h"
+#include "gpio.h"
+
+#define MX28EVK_FEC_PHY_POWER	MXS_GPIO_NR(2, 15)
+#define MX28EVK_FEC_PHY_RESET	MXS_GPIO_NR(4, 13)
+
+static const iomux_cfg_t mx28evk_pads[] __initconst = {
+	/* duart */
+	MX28_PAD_PWM0__DUART_RX |
+		(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	MX28_PAD_PWM1__DUART_TX |
+		(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+
+	/* fec0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	/* phy power line */
+	MX28_PAD_SSP1_DATA3__GPIO_2_15 |
+		(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	/* phy reset line */
+	MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+		(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+};
+
+/* fec */
+static void __init mx28evk_fec_reset(void)
+{
+	int ret;
+	struct clk *clk;
+
+	/* Enable fec phy clock */
+	clk = clk_get_sys("pll2", NULL);
+	if (!IS_ERR(clk))
+		clk_enable(clk);
+
+	/* Power up fec phy */
+	ret = gpio_request(MX28EVK_FEC_PHY_POWER, "fec-phy-power");
+	if (ret) {
+		pr_err("Failed to request gpio fec-phy-%s: %d\n", "power", ret);
+		return;
+	}
+
+	ret = gpio_direction_output(MX28EVK_FEC_PHY_POWER, 0);
+	if (ret) {
+		pr_err("Failed to drive gpio fec-phy-%s: %d\n", "power", ret);
+		return;
+	}
+
+	/* Reset fec phy */
+	ret = gpio_request(MX28EVK_FEC_PHY_RESET, "fec-phy-reset");
+	if (ret) {
+		pr_err("Failed to request gpio fec-phy-%s: %d\n", "reset", ret);
+		return;
+	}
+
+	gpio_direction_output(MX28EVK_FEC_PHY_RESET, 0);
+	if (ret) {
+		pr_err("Failed to drive gpio fec-phy-%s: %d\n", "reset", ret);
+		return;
+	}
+
+	mdelay(1);
+	gpio_set_value(MX28EVK_FEC_PHY_RESET, 1);
+}
+
+static const struct fec_platform_data mx28_fec_pdata __initconst = {
+	.phy = PHY_INTERFACE_MODE_RMII,
+};
+
+static void __init mx28evk_init(void)
+{
+	mxs_iomux_setup_multiple_pads(mx28evk_pads, ARRAY_SIZE(mx28evk_pads));
+
+	mx28_add_duart();
+
+	mx28evk_fec_reset();
+	mx28_add_fec(0, &mx28_fec_pdata);
+}
+
+static void __init mx28evk_timer_init(void)
+{
+	mx28_clocks_init();
+}
+
+static struct sys_timer mx28evk_timer = {
+	.init	= mx28evk_timer_init,
+};
+
+MACHINE_START(MX28EVK, "Freescale MX28 EVK")
+	/* Maintainer: Freescale Semiconductor, Inc. */
+	.map_io		= mx28_map_io,
+	.init_irq	= mx28_init_irq,
+	.init_machine	= mx28evk_init,
+	.timer		= &mx28evk_timer,
+MACHINE_END
-- 
1.7.1

^ permalink raw reply related	[flat|nested] 18+ messages in thread

end of thread, other threads:[~2010-12-20 14:35 UTC | newest]

Thread overview: 18+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-12-18 13:39 [PATCH v7 00/15] ARM: mxs: Add initial support for MX23 and MX28 Shawn Guo
2010-12-18 13:39 ` [PATCH v7 03/15] ARM: mxs: Add reset routines Shawn Guo
2010-12-18 13:39 ` [PATCH v7 04/15] ARM: mxs: Add interrupt support Shawn Guo
2010-12-18 13:39 ` [PATCH v7 05/15] ARM: mxs: Add low-level debug UART support Shawn Guo
2010-12-20 11:50   ` Wolfram Sang
2010-12-20 13:22     ` Shawn Guo
2010-12-20 13:55       ` Wolfram Sang
2010-12-20 14:25         ` Shawn Guo
2010-12-20 14:35           ` Wolfram Sang
2010-12-18 13:39 ` [PATCH v7 06/15] ARM: mxs: Add timer support Shawn Guo
2010-12-18 13:39 ` [PATCH v7 07/15] ARM: mxs: Add gpio support Shawn Guo
2010-12-18 13:39 ` [PATCH v7 08/15] ARM: mxs: Add iomux support Shawn Guo
2010-12-20  9:44   ` Uwe Kleine-König
2010-12-18 13:39 ` [PATCH v7 09/15] ARM: mxs: Add clock support Shawn Guo
2010-12-18 13:39 ` [PATCH v7 13/15] ARM: mxs: Add initial mx23evk support Shawn Guo
2010-12-20  9:48   ` Uwe Kleine-König
2010-12-20 10:17     ` Shawn Guo
2010-12-18 13:39 ` [PATCH v7 14/15] ARM: mxs: Add initial mx28evk support Shawn Guo

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).