From: adharmap@codeaurora.org (adharmap at codeaurora.org)
To: linux-arm-kernel@lists.infradead.org
Subject: [PM8921 MFD V3 0/6] pmic8921 core and subdevices
Date: Wed, 16 Mar 2011 19:23:55 -0700 [thread overview]
Message-ID: <1300328641-3855-1-git-send-email-adharmap@codeaurora.org> (raw)
This patch series adds support for pmic 8921 chip and its subdevices.
The pmic 8921 chip is used as a power management ic for 8960 based boards. It
communicates over the ssbi bus, ssbi bus can be found here
https://patchwork.kernel.org/patch/601771/
The patch set contains support for interrupt, gpio and mpp (multi purpose pin)
subdevices.
Note that gpio and mpp subdevices need the interrupt subdevice to
be operational, this is becuase the reading the the value of gpio/mpp lines
happens by doing a transaction over registers managed by the interrupt subdev.
The code invokes a call on interrupt subdevice, rather than writing to those
registers directly, avoiding race conditions.
Upates from v2
Thomas Gleixner's code cleanup comments, use of IRQCHIP_MASK_ON_SUSPEND.
Randy Dunlap's Kconfig cleanup comments.
Mark Brown's suggestion to move pm8921.h in include/linux/mfd/pm8xxx/pm8921.h
Grant Likely's suggestion of locking around the chip's list.
Thanks a lot for reviewing these patches.
Abhijeet Dharmapurikar (5):
mfd: pm8921: Add PMIC 8921 core driver
mfd: pm8xxx: Add irq support
gpio: pm8xxx-gpio: Add pm8xxx gpio driver
MAINTAINERS: Add patterns for pmic 8921 files to MSM subsystem
msm: board-8960: Add support for pm8921
David Collins (1):
mfd: pm8xxx-mpp: Add pm8xxx MPP driver
MAINTAINERS | 2 +
arch/arm/mach-msm/board-msm8960.c | 47 +++-
arch/arm/mach-msm/include/mach/irqs-8960.h | 9 +-
drivers/gpio/Kconfig | 8 +
drivers/gpio/Makefile | 1 +
drivers/gpio/pm8xxx-gpio.c | 455 ++++++++++++++++++++++++++++
drivers/mfd/Kconfig | 36 +++
drivers/mfd/Makefile | 3 +
drivers/mfd/pm8921-core.c | 278 +++++++++++++++++
drivers/mfd/pm8xxx-irq.c | 436 ++++++++++++++++++++++++++
drivers/mfd/pm8xxx-mpp.c | 327 ++++++++++++++++++++
include/linux/mfd/pm8xxx/core.h | 75 +++++
include/linux/mfd/pm8xxx/gpio.h | 132 ++++++++
include/linux/mfd/pm8xxx/irq.h | 69 +++++
include/linux/mfd/pm8xxx/mpp.h | 233 ++++++++++++++
include/linux/mfd/pm8xxx/pm8921.h | 48 +++
16 files changed, 2144 insertions(+), 15 deletions(-)
create mode 100644 drivers/gpio/pm8xxx-gpio.c
create mode 100644 drivers/mfd/pm8921-core.c
create mode 100644 drivers/mfd/pm8xxx-irq.c
create mode 100644 drivers/mfd/pm8xxx-mpp.c
create mode 100644 include/linux/mfd/pm8xxx/core.h
create mode 100644 include/linux/mfd/pm8xxx/gpio.h
create mode 100644 include/linux/mfd/pm8xxx/irq.h
create mode 100644 include/linux/mfd/pm8xxx/mpp.h
create mode 100644 include/linux/mfd/pm8xxx/pm8921.h
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
next reply other threads:[~2011-03-17 2:23 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-03-17 2:23 adharmap at codeaurora.org [this message]
2011-03-17 2:23 ` [PM8921 MFD V3 1/6] mfd: pm8921: Add PMIC 8921 core driver adharmap at codeaurora.org
2011-03-17 2:23 ` [PM8921 MFD V3 2/6] mfd: pm8xxx: Add irq support adharmap at codeaurora.org
2011-03-17 9:59 ` Thomas Gleixner
2011-03-17 2:23 ` [PM8921 MFD V3 3/6] gpio: pm8xxx-gpio: Add pm8xxx gpio driver adharmap at codeaurora.org
2011-03-17 18:00 ` Grant Likely
2011-03-17 20:27 ` Abhijeet Dharmapurikar
2011-03-17 20:35 ` Grant Likely
2011-03-17 2:23 ` [PM8921 MFD V3 4/6] mfd: pm8xxx-mpp: Add pm8xxx MPP driver adharmap at codeaurora.org
2011-03-17 2:24 ` [PM8921 MFD V3 5/6] MAINTAINERS: Add patterns for pmic 8921 files to MSM subsystem adharmap at codeaurora.org
2011-03-17 2:24 ` [PM8921 MFD V3 6/6] msm: board-8960: Add support for pm8921 adharmap at codeaurora.org
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1300328641-3855-1-git-send-email-adharmap@codeaurora.org \
--to=adharmap@codeaurora.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).