linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Dinh.Nguyen@freescale.com (Dinh.Nguyen at freescale.com)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCHv5 4/4] ARM: mx51: Add support for low power suspend on MX51
Date: Mon, 21 Mar 2011 16:30:38 -0500	[thread overview]
Message-ID: <1300743038-3901-4-git-send-email-Dinh.Nguyen@freescale.com> (raw)
In-Reply-To: <1300743038-3901-3-git-send-email-Dinh.Nguyen@freescale.com>

From: Dinh Nguyen <Dinh.Nguyen@freescale.com>

Adds initial low power suspend functionality to MX51.
Supports "mem" and "standby" modes.

Tested on mx51-babbage.

Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
---
 arch/arm/mach-mx5/Makefile   |    1 +
 arch/arm/mach-mx5/pm-imx51.c |   74 ++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 75 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mx5/pm-imx51.c

diff --git a/arch/arm/mach-mx5/Makefile b/arch/arm/mach-mx5/Makefile
index 0b9338c..787cb80 100644
--- a/arch/arm/mach-mx5/Makefile
+++ b/arch/arm/mach-mx5/Makefile
@@ -6,6 +6,7 @@
 obj-y   := cpu.o mm.o clock-mx51-mx53.o devices.o ehci.o system.o
 obj-$(CONFIG_SOC_IMX50) += mm-mx50.o
 
+obj-$(CONFIG_PM) += pm-imx51.o
 obj-$(CONFIG_CPU_FREQ_IMX)    += cpu_op-mx51.o
 obj-$(CONFIG_MACH_MX51_BABBAGE) += board-mx51_babbage.o
 obj-$(CONFIG_MACH_MX51_3DS) += board-mx51_3ds.o
diff --git a/arch/arm/mach-mx5/pm-imx51.c b/arch/arm/mach-mx5/pm-imx51.c
new file mode 100644
index 0000000..f5164b2
--- /dev/null
+++ b/arch/arm/mach-mx5/pm-imx51.c
@@ -0,0 +1,74 @@
+/*
+ *  Copyright (C) 2011 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+#include <linux/suspend.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <asm/cacheflush.h>
+#include <asm/tlbflush.h>
+#include <mach/system.h>
+#include "crm_regs.h"
+
+static struct clk *gpc_dvfs_clk;
+
+static int mx5_suspend_enter(suspend_state_t state)
+{
+	if (gpc_dvfs_clk == NULL)
+		gpc_dvfs_clk = clk_get(NULL, "gpc_dvfs");
+
+	if (gpc_dvfs_clk) {
+		clk_enable(gpc_dvfs_clk);
+		switch (state) {
+		case PM_SUSPEND_MEM:
+			mx5_cpu_lp_set(STOP_POWER_OFF);
+			break;
+		case PM_SUSPEND_STANDBY:
+			mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF);
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		if (state == PM_SUSPEND_MEM) {
+			local_flush_tlb_all();
+			flush_cache_all();
+
+			/*clear the EMPGC0/1 bits */
+			__raw_writel(0, MXC_SRPG_EMPGC0_SRPGCR);
+			__raw_writel(0, MXC_SRPG_EMPGC1_SRPGCR);
+		}
+		cpu_do_idle();
+		clk_disable(gpc_dvfs_clk);
+	}else {
+		printk(KERN_ERR "Cannot enter SRPG suspend -no gpc_dvfs clock!\n");
+		return -EPERM;
+	}
+
+	return 0;
+}
+
+static int mx5_pm_valid(suspend_state_t state)
+{
+	return (state > PM_SUSPEND_ON && state <= PM_SUSPEND_MAX);
+}
+
+static const struct platform_suspend_ops mx5_suspend_ops = {
+	.valid = mx5_pm_valid,
+	.enter = mx5_suspend_enter,
+};
+
+static int __init mx5_pm_init(void)
+{
+	if (cpu_is_mx51())
+		suspend_set_ops(&mx5_suspend_ops);
+
+	return 0;
+}
+device_initcall(mx5_pm_init);
-- 
1.6.0.4

  reply	other threads:[~2011-03-21 21:30 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-03-21 21:30 [PATCHv5 1/4] ARM: mx50: Add support to get the silicon revision Dinh.Nguyen at freescale.com
2011-03-21 21:30 ` [PATCHv5 2/4] ARM: mx51: Add entry for gpc_dvfs_clk Dinh.Nguyen at freescale.com
2011-03-21 21:30   ` [PATCHv5 3/4] ARM: mx51: Implement code to allow mx51 to enter WFI Dinh.Nguyen at freescale.com
2011-03-21 21:30     ` Dinh.Nguyen at freescale.com [this message]
2011-03-23 10:24       ` [PATCHv5 4/4] ARM: mx51: Add support for low power suspend on MX51 Sascha Hauer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1300743038-3901-4-git-send-email-Dinh.Nguyen@freescale.com \
    --to=dinh.nguyen@freescale.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).