From: khilman@ti.com (Kevin Hilman)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 2/2] I2C: OMAP: remove dev->idle, use usage counting provided by runtime PM
Date: Thu, 4 Aug 2011 07:57:36 -0700 [thread overview]
Message-ID: <1312469856-13276-3-git-send-email-khilman@ti.com> (raw)
In-Reply-To: <1312469856-13276-1-git-send-email-khilman@ti.com>
Current usage of runtime PM is not quite correct. The actual
idle/unidle of the I2C hardware should not happen until the runtime PM
callbacks are called. Therefore, change omap_i2c_[un]idle() functions
to only be called from the runtime PM callbacks (when usage count
transitions to/from zero.)
Also, the runtime PM core does usage counting and replaces
functionality currently managed by the dev->idle flag. Remove usage
of dev->idle in favor of using runtime PM, and checking status using
pm_runtime_suspended().
Signed-off-by: Kevin Hilman <khilman@ti.com>
---
drivers/i2c/busses/i2c-omap.c | 59 +++++++++++++++++++++++++++--------------
1 files changed, 39 insertions(+), 20 deletions(-)
diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 12d0cbc..1c75d13 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -194,7 +194,6 @@ struct omap_i2c_dev {
*/
u8 rev;
unsigned b_hw:1; /* bad h/w fixes */
- unsigned idle:1;
u16 iestate; /* Saved interrupt register */
u16 pscstate;
u16 scllstate;
@@ -269,12 +268,8 @@ static void omap_i2c_unidle(struct omap_i2c_dev *dev)
{
struct omap_i2c_bus_platform_data *pdata;
- WARN_ON(!dev->idle);
-
pdata = dev->dev->platform_data;
- pm_runtime_get_sync(dev->dev);
-
if (pdata->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) {
omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate);
@@ -285,7 +280,6 @@ static void omap_i2c_unidle(struct omap_i2c_dev *dev)
omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, dev->westate);
omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
}
- dev->idle = 0;
/*
* Don't write to this register if the IE state is 0 as it can
@@ -300,8 +294,6 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev)
struct omap_i2c_bus_platform_data *pdata;
u16 iv;
- WARN_ON(dev->idle);
-
pdata = dev->dev->platform_data;
dev->iestate = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
@@ -315,12 +307,9 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev)
} else {
omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, dev->iestate);
- /* Flush posted write before the dev->idle store occurs */
+ /* Flush posted write */
omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
}
- dev->idle = 1;
-
- pm_runtime_put_sync(dev->dev);
}
static int omap_i2c_init(struct omap_i2c_dev *dev)
@@ -644,7 +633,7 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
int i;
int r;
- omap_i2c_unidle(dev);
+ pm_runtime_get_sync(dev->dev);
r = omap_i2c_wait_for_bb(dev);
if (r < 0)
@@ -667,7 +656,7 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
omap_i2c_wait_for_bb(dev);
out:
- omap_i2c_idle(dev);
+ pm_runtime_put(dev->dev);
return r;
}
@@ -727,7 +716,7 @@ omap_i2c_omap1_isr(int this_irq, void *dev_id)
struct omap_i2c_dev *dev = dev_id;
u16 iv, w;
- if (dev->idle)
+ if (pm_runtime_suspended(dev->dev))
return IRQ_NONE;
iv = omap_i2c_read_reg(dev, OMAP_I2C_IV_REG);
@@ -819,7 +808,7 @@ omap_i2c_isr(int this_irq, void *dev_id)
pdata = dev->dev->platform_data;
- if (dev->idle)
+ if (pm_runtime_suspended(dev->dev))
return IRQ_NONE;
bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
@@ -1021,7 +1010,6 @@ omap_i2c_probe(struct platform_device *pdev)
}
dev->speed = speed;
- dev->idle = 1;
dev->dev = &pdev->dev;
dev->irq = irq->start;
dev->base = ioremap(mem->start, resource_size(mem));
@@ -1040,7 +1028,7 @@ omap_i2c_probe(struct platform_device *pdev)
dev->regs = (u8 *)reg_map_ip_v1;
pm_runtime_enable(dev->dev);
- omap_i2c_unidle(dev);
+ pm_runtime_get_sync(dev->dev);
dev->rev = omap_i2c_read_reg(dev, OMAP_I2C_REV_REG) & 0xff;
@@ -1087,7 +1075,7 @@ omap_i2c_probe(struct platform_device *pdev)
dev_info(dev->dev, "bus %d rev%d.%d.%d at %d kHz\n", pdev->id,
pdata->rev, dev->rev >> 4, dev->rev & 0xf, dev->speed);
- omap_i2c_idle(dev);
+ pm_runtime_put(dev->dev);
adap = &dev->adapter;
i2c_set_adapdata(adap, dev);
@@ -1111,7 +1099,7 @@ err_free_irq:
free_irq(dev->irq, dev);
err_unuse_clocks:
omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
- omap_i2c_idle(dev);
+ pm_runtime_put(dev->dev);
iounmap(dev->base);
err_free_mem:
platform_set_drvdata(pdev, NULL);
@@ -1140,12 +1128,43 @@ omap_i2c_remove(struct platform_device *pdev)
return 0;
}
+#ifdef CONFIG_PM_RUNTIME
+static int omap_i2c_runtime_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct omap_i2c_dev *_dev = platform_get_drvdata(pdev);
+
+ omap_i2c_idle(_dev);
+
+ return 0;
+}
+
+static int omap_i2c_runtime_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct omap_i2c_dev *_dev = platform_get_drvdata(pdev);
+
+ omap_i2c_unidle(_dev);
+
+ return 0;
+}
+
+static struct dev_pm_ops omap_i2c_pm_ops = {
+ .runtime_suspend = omap_i2c_runtime_suspend,
+ .runtime_resume = omap_i2c_runtime_resume,
+};
+#define OMAP_I2C_PM_OPS (&omap_i2c_pm_ops)
+#else
+#define OMAP_I2C_PM_OPS NULL
+#endif
+
static struct platform_driver omap_i2c_driver = {
.probe = omap_i2c_probe,
.remove = omap_i2c_remove,
.driver = {
.name = "omap_i2c",
.owner = THIS_MODULE,
+ .pm = OMAP_I2C_PM_OPS,
},
};
--
1.7.6
next prev parent reply other threads:[~2011-08-04 14:57 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-04 14:57 [PATCH v2 0/2] I2C: OMAP: misc. PM-related cleanups Kevin Hilman
2011-08-04 14:57 ` [PATCH v2 1/2] I2C: OMAP: remove unneccesary use of pdev Kevin Hilman
2011-08-04 14:57 ` Kevin Hilman [this message]
2011-08-04 15:10 ` [PATCH 3/2] I2C: OMAP: remove unused function pointers from pdata Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1312469856-13276-3-git-send-email-khilman@ti.com \
--to=khilman@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).