From: shawn.guo@linaro.org (Shawn Guo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 2/8] arm/mxc: do not use gpio_to_irq() for static initializers
Date: Sun, 14 Aug 2011 00:14:01 +0800 [thread overview]
Message-ID: <1313252047-8820-3-git-send-email-shawn.guo@linaro.org> (raw)
In-Reply-To: <1313252047-8820-1-git-send-email-shawn.guo@linaro.org>
The patch defines IMX_GPIO_TO_IRQ() in mach/hardware.h and replaces
all the uses of gpio_to_irq() in static initializers with
IMX_GPIO_TO_IRQ().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/mach-cpuimx35.c | 2 +-
arch/arm/mach-imx/mach-mx27_3ds.c | 2 +-
arch/arm/mach-imx/mach-vpr200.c | 2 +-
arch/arm/mach-mx5/board-cpuimx51.c | 8 ++++----
arch/arm/mach-mx5/board-cpuimx51sd.c | 4 ++--
arch/arm/mach-mx5/board-mx53_ard.c | 4 ++--
arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c | 2 +-
arch/arm/mach-mx5/mx51_efika.c | 2 +-
arch/arm/plat-mxc/include/mach/hardware.h | 2 ++
9 files changed, 15 insertions(+), 13 deletions(-)
diff --git a/arch/arm/mach-imx/mach-cpuimx35.c b/arch/arm/mach-imx/mach-cpuimx35.c
index f39a478b..13b7041 100644
--- a/arch/arm/mach-imx/mach-cpuimx35.c
+++ b/arch/arm/mach-imx/mach-cpuimx35.c
@@ -66,7 +66,7 @@ static struct i2c_board_info eukrea_cpuimx35_i2c_devices[] = {
I2C_BOARD_INFO("tsc2007", 0x48),
.type = "tsc2007",
.platform_data = &tsc2007_info,
- .irq = gpio_to_irq(TSC2007_IRQGPIO),
+ .irq = IMX_GPIO_TO_IRQ(TSC2007_IRQGPIO),
},
};
diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c
index 6fa6934..097ff42 100644
--- a/arch/arm/mach-imx/mach-mx27_3ds.c
+++ b/arch/arm/mach-imx/mach-mx27_3ds.c
@@ -359,7 +359,7 @@ static struct spi_board_info mx27_3ds_spi_devs[] __initdata = {
.bus_num = 1,
.chip_select = 0, /* SS0 */
.platform_data = &mc13783_pdata,
- .irq = gpio_to_irq(PMIC_INT),
+ .irq = IMX_GPIO_TO_IRQ(PMIC_INT),
.mode = SPI_CS_HIGH,
}, {
.modalias = "l4f00242t03",
diff --git a/arch/arm/mach-imx/mach-vpr200.c b/arch/arm/mach-imx/mach-vpr200.c
index 7d8e012..5250283 100644
--- a/arch/arm/mach-imx/mach-vpr200.c
+++ b/arch/arm/mach-imx/mach-vpr200.c
@@ -162,7 +162,7 @@ static struct i2c_board_info vpr200_i2c_devices[] = {
}, {
I2C_BOARD_INFO("mc13892", 0x08),
.platform_data = &vpr200_pmic,
- .irq = gpio_to_irq(GPIO_PMIC_INT),
+ .irq = IMX_GPIO_TO_IRQ(GPIO_PMIC_INT),
}
};
diff --git a/arch/arm/mach-mx5/board-cpuimx51.c b/arch/arm/mach-mx5/board-cpuimx51.c
index 68934ea..49ec98e 100644
--- a/arch/arm/mach-mx5/board-cpuimx51.c
+++ b/arch/arm/mach-mx5/board-cpuimx51.c
@@ -57,7 +57,7 @@
static struct plat_serial8250_port serial_platform_data[] = {
{
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x400000),
- .irq = gpio_to_irq(CPUIMX51_QUARTA_GPIO),
+ .irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTA_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
@@ -65,7 +65,7 @@ static struct plat_serial8250_port serial_platform_data[] = {
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
}, {
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x800000),
- .irq = gpio_to_irq(CPUIMX51_QUARTB_GPIO),
+ .irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTB_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
@@ -73,7 +73,7 @@ static struct plat_serial8250_port serial_platform_data[] = {
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
}, {
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x1000000),
- .irq = gpio_to_irq(CPUIMX51_QUARTC_GPIO),
+ .irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTC_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
@@ -81,7 +81,7 @@ static struct plat_serial8250_port serial_platform_data[] = {
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
}, {
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x2000000),
- .irq = gpio_to_irq(CPUIMX51_QUARTD_GPIO),
+ .irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTD_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
diff --git a/arch/arm/mach-mx5/board-cpuimx51sd.c b/arch/arm/mach-mx5/board-cpuimx51sd.c
index ff096d5..8badbdb 100644
--- a/arch/arm/mach-mx5/board-cpuimx51sd.c
+++ b/arch/arm/mach-mx5/board-cpuimx51sd.c
@@ -129,7 +129,7 @@ static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
I2C_BOARD_INFO("tsc2007", 0x49),
.type = "tsc2007",
.platform_data = &tsc2007_info,
- .irq = gpio_to_irq(TSC2007_IRQGPIO),
+ .irq = IMX_GPIO_TO_IRQ(TSC2007_IRQGPIO),
},
};
@@ -245,7 +245,7 @@ static struct spi_board_info cpuimx51sd_spi_device[] = {
.mode = SPI_MODE_0,
.chip_select = 0,
.platform_data = &mcp251x_info,
- .irq = gpio_to_irq(CAN_IRQGPIO)
+ .irq = IMX_GPIO_TO_IRQ(CAN_IRQGPIO)
},
};
diff --git a/arch/arm/mach-mx5/board-mx53_ard.c b/arch/arm/mach-mx5/board-mx53_ard.c
index 76a67c4..ddc3015 100644
--- a/arch/arm/mach-mx5/board-mx53_ard.c
+++ b/arch/arm/mach-mx5/board-mx53_ard.c
@@ -134,8 +134,8 @@ static struct resource ard_smsc911x_resources[] = {
.flags = IORESOURCE_MEM,
},
{
- .start = gpio_to_irq(ARD_ETHERNET_INT_B),
- .end = gpio_to_irq(ARD_ETHERNET_INT_B),
+ .start = IMX_GPIO_TO_IRQ(ARD_ETHERNET_INT_B),
+ .end = IMX_GPIO_TO_IRQ(ARD_ETHERNET_INT_B),
.flags = IORESOURCE_IRQ,
},
};
diff --git a/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c b/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c
index bbf4564..ab0b1b2 100644
--- a/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c
+++ b/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c
@@ -160,7 +160,7 @@ struct tsc2007_platform_data tsc2007_data = {
static struct i2c_board_info mbimx51_i2c_devices[] = {
{
I2C_BOARD_INFO("tsc2007", 0x49),
- .irq = gpio_to_irq(MBIMX51_TSC2007_GPIO),
+ .irq = IMX_GPIO_TO_IRQ(MBIMX51_TSC2007_GPIO),
.platform_data = &tsc2007_data,
}, {
I2C_BOARD_INFO("tlv320aic23", 0x1a),
diff --git a/arch/arm/mach-mx5/mx51_efika.c b/arch/arm/mach-mx5/mx51_efika.c
index 4435e03..2a3015a 100644
--- a/arch/arm/mach-mx5/mx51_efika.c
+++ b/arch/arm/mach-mx5/mx51_efika.c
@@ -589,7 +589,7 @@ static struct spi_board_info mx51_efika_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 0,
.platform_data = &mx51_efika_mc13892_data,
- .irq = gpio_to_irq(EFIKAMX_PMIC),
+ .irq = IMX_GPIO_TO_IRQ(EFIKAMX_PMIC),
},
};
diff --git a/arch/arm/plat-mxc/include/mach/hardware.h b/arch/arm/plat-mxc/include/mach/hardware.h
index a8bfd56..77f6556 100644
--- a/arch/arm/plat-mxc/include/mach/hardware.h
+++ b/arch/arm/plat-mxc/include/mach/hardware.h
@@ -116,4 +116,6 @@
.type = _type, \
}
+#define IMX_GPIO_TO_IRQ(gpio) (MXC_GPIO_IRQ_START + (gpio))
+
#endif /* __ASM_ARCH_MXC_HARDWARE_H__ */
--
1.7.4.1
next prev parent reply other threads:[~2011-08-13 16:14 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-13 16:13 [PATCH v2 0/8] Clean up MXC and MXS mach/gpio.h Shawn Guo
2011-08-13 16:14 ` [PATCH v2 1/8] ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage Shawn Guo
2011-08-13 16:14 ` Shawn Guo [this message]
2011-08-13 16:14 ` [PATCH v2 3/8] gpio/mxc: add .to_irq for gpio chip Shawn Guo
2011-08-13 16:14 ` [PATCH v2 4/8] arm/mxc: remove gpio_to_irq() from mach/gpio.h Shawn Guo
2011-08-13 16:14 ` [PATCH v2 5/8] gpio/mxc: move irq_to_gpio() into gpio-mxc driver Shawn Guo
2011-08-13 16:14 ` [PATCH v2 6/8] arm/mxc: move IMX_GPIO_NR into mach/hardware.h Shawn Guo
2011-08-13 16:14 ` [PATCH v2 7/8] gpio/mxs: move irq_to_gpio() into gpio-mxs driver Shawn Guo
2011-08-13 16:14 ` [PATCH v2 8/8] arm/mxs: move MXS_GPIO_NR into mach/mxs.h Shawn Guo
2011-08-16 7:19 ` [PATCH v2 0/8] Clean up MXC and MXS mach/gpio.h Sascha Hauer
2011-08-17 6:25 ` Shawn Guo
2011-08-17 6:47 ` Sascha Hauer
2011-08-17 7:10 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1313252047-8820-3-git-send-email-shawn.guo@linaro.org \
--to=shawn.guo@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).