From: govindraj.raja@ti.com (Govindraj.R)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v5 08/15] OMAP2+: UART: Store certain reg values to port structure
Date: Wed, 21 Sep 2011 17:43:25 +0530 [thread overview]
Message-ID: <1316607206-21669-6-git-send-email-govindraj.raja@ti.com> (raw)
In-Reply-To: <1316607206-21669-1-git-send-email-govindraj.raja@ti.com>
In preparation to runtime conversion add missing uart regs to
port structure which can be used in context restore.
Also ensuring all uart reg info's are part of port structure.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
---
arch/arm/plat-omap/include/plat/omap-serial.h | 3 ++
drivers/tty/serial/omap-serial.c | 33 ++++++++++++++----------
2 files changed, 22 insertions(+), 14 deletions(-)
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
index 0f061b4..74822b3 100644
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -99,6 +99,9 @@ struct uart_omap_port {
unsigned char mcr;
unsigned char fcr;
unsigned char efr;
+ unsigned char dll;
+ unsigned char dlh;
+ unsigned char mdr1;
int use_dma;
/*
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index 6c2ea54..9a0eac2 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -433,8 +433,9 @@ static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
if (mctrl & TIOCM_LOOP)
mcr |= UART_MCR_LOOP;
- mcr |= up->mcr;
- serial_out(up, UART_MCR, mcr);
+ up->mcr = serial_in(up, UART_MCR);
+ up->mcr |= mcr;
+ serial_out(up, UART_MCR, up->mcr);
}
static void serial_omap_break_ctl(struct uart_port *port, int break_state)
@@ -573,8 +574,6 @@ static inline void
serial_omap_configure_xonxoff
(struct uart_omap_port *up, struct ktermios *termios)
{
- unsigned char efr = 0;
-
up->lcr = serial_in(up, UART_LCR);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
up->efr = serial_in(up, UART_EFR);
@@ -584,8 +583,7 @@ serial_omap_configure_xonxoff
serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]);
/* clear SW control mode bits */
- efr = up->efr;
- efr &= OMAP_UART_SW_CLR;
+ up->efr &= OMAP_UART_SW_CLR;
/*
* IXON Flag:
@@ -593,7 +591,7 @@ serial_omap_configure_xonxoff
* Transmit XON1, XOFF1
*/
if (termios->c_iflag & IXON)
- efr |= OMAP_UART_SW_TX;
+ up->efr |= OMAP_UART_SW_TX;
/*
* IXOFF Flag:
@@ -601,7 +599,7 @@ serial_omap_configure_xonxoff
* Receiver compares XON1, XOFF1.
*/
if (termios->c_iflag & IXOFF)
- efr |= OMAP_UART_SW_RX;
+ up->efr |= OMAP_UART_SW_RX;
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
@@ -624,7 +622,7 @@ serial_omap_configure_xonxoff
* load the new software flow control mode IXON or IXOFF
* and restore the UARTi.EFR_REG[4] ENHANCED_EN value.
*/
- serial_out(up, UART_EFR, efr | UART_EFR_SCD);
+ serial_out(up, UART_EFR, up->efr | UART_EFR_SCD);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_MCR, up->mcr & ~UART_MCR_TCRTLR);
@@ -671,6 +669,10 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
quot = serial_omap_get_divisor(port, baud);
+ up->dll = quot & 0xff;
+ up->dlh = quot >> 8;
+ up->mdr1 = UART_OMAP_MDR1_DISABLE;
+
up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
UART_FCR_ENABLE_FIFO;
if (up->use_dma)
@@ -723,6 +725,7 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, cval); /* reset DLAB */
+ up->lcr = cval;
/* FIFOs and DMA Settings */
@@ -759,7 +762,7 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
/* Protocol, Baud Rate, and Interrupt Settings */
- serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
+ serial_out(up, UART_OMAP_MDR1, up->mdr1);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
up->efr = serial_in(up, UART_EFR);
@@ -769,8 +772,8 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
serial_out(up, UART_IER, 0);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
- serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
+ serial_out(up, UART_DLL, up->dll); /* LS of divisor */
+ serial_out(up, UART_DLM, up->dlh); /* MS of divisor */
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, up->ier);
@@ -780,9 +783,11 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
serial_out(up, UART_LCR, cval);
if (baud > 230400 && baud != 3000000)
- serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_13X_MODE);
+ up->mdr1 = UART_OMAP_MDR1_13X_MODE;
else
- serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE);
+ up->mdr1 = UART_OMAP_MDR1_16X_MODE;
+
+ serial_out(up, UART_OMAP_MDR1, up->mdr1);
/* Hardware Flow Control Configuration */
--
1.7.4.1
next prev parent reply other threads:[~2011-09-21 12:13 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-21 12:13 [PATCH v5 03/15] OMAP2+: UART: cleanup + remove uart pm specific API Govindraj.R
2011-09-21 12:13 ` [PATCH v5 04/15] OMAP2+: UART: cleanup 8250 console driver support Govindraj.R
2011-09-21 12:13 ` [PATCH v5 05/15] OMAP2+: UART: Cleanup part of clock gating mechanism for uart Govindraj.R
2011-09-21 12:13 ` [PATCH v5 06/15] OMAP2+: UART: Remove certain feilds from omap_uart_state struct Govindraj.R
2011-09-21 12:13 ` [PATCH v5 07/15] OMAP2+: UART: Add default mux for all uarts Govindraj.R
2011-09-21 12:13 ` Govindraj.R [this message]
2011-09-21 12:13 ` [PATCH v5 09/15] OMAP2+: UART: Add runtime pm support for omap-serial driver Govindraj.R
2011-09-22 7:48 ` Ming Lei
2011-09-22 7:55 ` Govindraj
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1316607206-21669-6-git-send-email-govindraj.raja@ti.com \
--to=govindraj.raja@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).