From: vishwanath.bs@ti.com (Vishwanath BS)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCHv2 3/7] ARM: OMAP4 PM: Add IO Daisychain support
Date: Fri, 7 Oct 2011 23:17:47 +0530 [thread overview]
Message-ID: <1318009671-12813-4-git-send-email-vishwanath.bs@ti.com> (raw)
In-Reply-To: <1318009671-12813-1-git-send-email-vishwanath.bs@ti.com>
From: Rajendra Nayak <rnayak@ti.com>
patch adds IO Daisychain support for OMAP4 as per section 3.9.4 in OMAP4430
Public TRM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
---
arch/arm/mach-omap2/prm44xx.c | 33 +++++++++++++++++++++++++++++++++
arch/arm/mach-omap2/prm44xx.h | 1 +
2 files changed, 34 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/prm44xx.c b/arch/arm/mach-omap2/prm44xx.c
index 0016555..7e19678 100644
--- a/arch/arm/mach-omap2/prm44xx.c
+++ b/arch/arm/mach-omap2/prm44xx.c
@@ -23,6 +23,8 @@
#include "prm44xx.h"
#include "prm-regbits-44xx.h"
+#include "prcm44xx.h"
+#include "prminst44xx.h"
/* PRM low-level functions */
@@ -50,3 +52,34 @@ u32 omap4_prm_rmw_inst_reg_bits(u32 mask, u32 bits, s16 inst, s16 reg)
return v;
}
+
+/**
+ * Maximum time(us) it takes to output the signal WUCLKOUT of the last pad of
+ * the I/O ring after asserting WUCLKIN high
+ */
+#define MAX_IOPAD_LATCH_TIME 1000
+
+/* OMAP4 IO Daisychain trigger sequence */
+void omap4_trigger_wuclk_ctrl(void)
+{
+ int i = 0;
+
+ /* Enable GLOBAL_WUEN */
+ if (!(omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST, OMAP4_PRM_IO_PMCTRL_OFFSET)
+ & OMAP4430_GLOBAL_WUEN_MASK))
+ omap4_prm_rmw_inst_reg_bits(OMAP4430_GLOBAL_WUEN_MASK,
+ OMAP4430_GLOBAL_WUEN_MASK, OMAP4430_PRM_DEVICE_INST,
+ OMAP4_PRM_IO_PMCTRL_OFFSET);
+
+ /* Trigger WUCLKIN enable */
+ omap4_prm_rmw_inst_reg_bits(OMAP4430_WUCLK_CTRL_MASK, OMAP4430_WUCLK_CTRL_MASK,
+ OMAP4430_PRM_DEVICE_INST, OMAP4_PRM_IO_PMCTRL_OFFSET);
+ omap_test_timeout(
+ ((omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST, OMAP4_PRM_IO_PMCTRL_OFFSET)
+ >> OMAP4430_WUCLK_STATUS_SHIFT) == 1), MAX_IOPAD_LATCH_TIME, i);
+ /* Trigger WUCLKIN disable */
+ omap4_prm_rmw_inst_reg_bits(OMAP4430_WUCLK_CTRL_MASK, 0x0,
+ OMAP4430_PRM_DEVICE_INST, OMAP4_PRM_IO_PMCTRL_OFFSET);
+ return;
+}
+
diff --git a/arch/arm/mach-omap2/prm44xx.h b/arch/arm/mach-omap2/prm44xx.h
index 7dfa379..275b25a 100644
--- a/arch/arm/mach-omap2/prm44xx.h
+++ b/arch/arm/mach-omap2/prm44xx.h
@@ -750,6 +750,7 @@
extern u32 omap4_prm_read_inst_reg(s16 inst, u16 idx);
extern void omap4_prm_write_inst_reg(u32 val, s16 inst, u16 idx);
extern u32 omap4_prm_rmw_inst_reg_bits(u32 mask, u32 bits, s16 inst, s16 idx);
+extern void omap4_trigger_wuclk_ctrl(void);
# endif
--
1.7.0.4
next prev parent reply other threads:[~2011-10-07 17:47 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-10-07 17:47 [PATCHv2 0/7]ARM: OMAP3PLUS PM: Add IO DaisyChain support via hwmod mux Vishwanath BS
2011-10-07 17:47 ` [PATCHv2 1/7] ARM: OMAP3 PM: correct enable/disable of daisy io chain Vishwanath BS
2011-10-07 17:47 ` [PATCHv2 2/7] ARM: OMAP3 PM: Move IO Daisychain function to omap3 prm file Vishwanath BS
2011-10-07 17:47 ` Vishwanath BS [this message]
2011-10-07 17:47 ` [PATCHv2 4/7] ARM: OMAP3 PM: Enable IO Wake up Vishwanath BS
2011-10-07 17:47 ` [PATCHv2 5/7] ARM: OMAP3PLUS PM: Add IO Daisychain support via hwmod mux Vishwanath BS
2011-10-07 17:47 ` [PATCHv2 6/7] ARM: OMAP3 PM: Remove IO Daisychain control from cpuidle Vishwanath BS
2011-10-07 17:47 ` [PATCHv2 7/7] ARM: OMAP3 PM: Enable IO Daisychain for supported chips Vishwanath BS
2011-11-08 0:58 ` [PATCHv2 0/7]ARM: OMAP3PLUS PM: Add IO DaisyChain support via hwmod mux Kevin Hilman
2011-11-29 11:22 ` Vishwanath Sripathy
2011-11-29 14:59 ` Vishwanath Sripathy
2011-11-30 0:48 ` Kevin Hilman
2011-11-30 9:27 ` Vishwanath Sripathy
2011-12-02 16:58 ` Vishwanath Sripathy
2011-12-13 14:23 ` Vishwanath Sripathy
2011-12-13 19:31 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1318009671-12813-4-git-send-email-vishwanath.bs@ti.com \
--to=vishwanath.bs@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).