From: hemantp@ti.com (Hemant Pedanekar)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH RESEND v5 3/3] ARM: OMAP: TI814X: Create board support and enable build for TI8148 EVM
Date: Sat, 10 Dec 2011 07:15:08 +0530 [thread overview]
Message-ID: <1323481508-28015-1-git-send-email-hemantp@ti.com> (raw)
This patch adds minimal support and build configuration for TI8148 EVM. Also
adds support for low level debugging on UART1 console on the EVM.
Note that existing TI8168 EVM file (board-ti8168evm.c) is updated with machine
info for TI8148 EVM.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
---
arch/arm/mach-omap2/Kconfig | 5 +++++
arch/arm/mach-omap2/Makefile | 1 +
arch/arm/mach-omap2/board-ti8168evm.c | 22 ++++++++++++++++------
arch/arm/plat-omap/include/plat/uncompress.h | 3 +++
4 files changed, 25 insertions(+), 6 deletions(-)
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index a34d0f7..cb760ac 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -322,6 +322,11 @@ config MACH_TI8168EVM
depends on SOC_OMAPTI81XX
default y
+config MACH_TI8148EVM
+ bool "TI8148 Evaluation Module"
+ depends on SOC_OMAPTI81XX
+ default y
+
config MACH_OMAP_4430SDP
bool "OMAP 4430 SDP board"
default y
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 9a6da52..b9e0990 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -236,6 +236,7 @@ obj-$(CONFIG_MACH_CRANEBOARD) += board-am3517crane.o
obj-$(CONFIG_MACH_SBC3530) += board-omap3stalker.o
obj-$(CONFIG_MACH_TI8168EVM) += board-ti8168evm.o
+obj-$(CONFIG_MACH_TI8148EVM) += board-ti8168evm.o
# Platform specific device init code
diff --git a/arch/arm/mach-omap2/board-ti8168evm.c b/arch/arm/mach-omap2/board-ti8168evm.c
index b236fcc..b3ca997 100644
--- a/arch/arm/mach-omap2/board-ti8168evm.c
+++ b/arch/arm/mach-omap2/board-ti8168evm.c
@@ -1,5 +1,5 @@
/*
- * Code for TI8168 EVM.
+ * Code for TI8168/TI8148 EVM.
*
* Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
*
@@ -24,15 +24,15 @@
#include <plat/board.h>
#include "common.h"
-static struct omap_board_config_kernel ti8168_evm_config[] __initdata = {
+static struct omap_board_config_kernel ti81xx_evm_config[] __initdata = {
};
-static void __init ti8168_evm_init(void)
+static void __init ti81xx_evm_init(void)
{
omap_serial_init();
omap_sdrc_init(NULL, NULL);
- omap_board_config = ti8168_evm_config;
- omap_board_config_size = ARRAY_SIZE(ti8168_evm_config);
+ omap_board_config = ti81xx_evm_config;
+ omap_board_config_size = ARRAY_SIZE(ti81xx_evm_config);
}
MACHINE_START(TI8168EVM, "ti8168evm")
@@ -42,5 +42,15 @@ MACHINE_START(TI8168EVM, "ti8168evm")
.init_early = ti81xx_init_early,
.init_irq = ti81xx_init_irq,
.timer = &omap3_timer,
- .init_machine = ti8168_evm_init,
+ .init_machine = ti81xx_evm_init,
+MACHINE_END
+
+MACHINE_START(TI8148EVM, "ti8148evm")
+ /* Maintainer: Texas Instruments */
+ .atag_offset = 0x100,
+ .map_io = ti81xx_map_io,
+ .init_early = ti81xx_init_early,
+ .init_irq = ti81xx_init_irq,
+ .timer = &omap3_timer,
+ .init_machine = ti81xx_evm_init,
MACHINE_END
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
index 7fbc361..6ee9049 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -179,6 +179,9 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
/* TI8168 base boards using UART3 */
DEBUG_LL_TI81XX(3, ti8168evm);
+ /* TI8148 base boards using UART1 */
+ DEBUG_LL_TI81XX(1, ti8148evm);
+
} while (0);
}
--
1.7.0.4
next reply other threads:[~2011-12-10 1:45 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-12-10 1:45 Hemant Pedanekar [this message]
-- strict thread matches above, loose matches on Subject: below --
2011-12-10 1:58 [PATCH RESEND v5 0/3] Add support for TI814X processor series Hemant Pedanekar
2011-12-10 1:58 ` [PATCH RESEND v5 3/3] ARM: OMAP: TI814X: Create board support and enable build for TI8148 EVM Hemant Pedanekar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1323481508-28015-1-git-send-email-hemantp@ti.com \
--to=hemantp@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).