From: shawn.guo@linaro.org (Shawn Guo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4/4] arm/imx: add mc13892 support into imx51-babbage.dts
Date: Wed, 21 Dec 2011 23:00:47 +0800 [thread overview]
Message-ID: <1324479647-4580-5-git-send-email-shawn.guo@linaro.org> (raw)
In-Reply-To: <1324479647-4580-1-git-send-email-shawn.guo@linaro.org>
It adds mc13892 support into imx51-babbage device tree source.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/arm/boot/dts/imx51-babbage.dts | 93 ++++++++++++++++++++++++++++++++++-
1 files changed, 91 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts
index 564cb8c..728c9e8 100644
--- a/arch/arm/boot/dts/imx51-babbage.dts
+++ b/arch/arm/boot/dts/imx51-babbage.dts
@@ -31,12 +31,14 @@
esdhc at 70004000 { /* ESDHC1 */
fsl,cd-internal;
fsl,wp-internal;
+ vmmc-supply = <&vsd_reg>;
status = "okay";
};
esdhc at 70008000 { /* ESDHC2 */
cd-gpios = <&gpio1 6 0>;
wp-gpios = <&gpio1 5 0>;
+ vmmc-supply = <&vsd_reg>;
status = "okay";
};
@@ -56,8 +58,95 @@
compatible = "fsl,mc13892";
spi-max-frequency = <6000000>;
reg = <0>;
- mc13xxx-irq-gpios = <&gpio1 8 0>;
- fsl,mc13xxx-uses-regulator;
+ interrupt-parent = <&gpio1>;
+ interrupts = <8>;
+
+ regulators {
+ sw1_reg: sw1 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1375000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3_reg: sw3 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vpll_reg: vpll {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdig_reg: vdig {
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ };
+
+ vsd_reg: vsd {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3150000>;
+ };
+
+ vusb2_reg: vusb2 {
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <2775000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vvideo_reg: vvideo {
+ regulator-min-microvolt = <2775000>;
+ regulator-max-microvolt = <2775000>;
+ };
+
+ vaudio_reg: vaudio {
+ regulator-min-microvolt = <2300000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vcam_reg: vcam {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-always-on;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-always-on;
+ };
+ };
};
flash: at45db321d at 1 {
--
1.7.4.1
next prev parent reply other threads:[~2011-12-21 15:00 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-12-21 15:00 [PATCH v4 0/4] Add device tree support for mc13892 regulator driver Shawn Guo
2011-12-21 15:00 ` [PATCH 1/4] mfd: improve mc13xxx dt binding document Shawn Guo
2011-12-22 11:05 ` Mark Brown
2011-12-22 16:07 ` Samuel Ortiz
2011-12-21 15:00 ` [PATCH 2/4] regulator: mc13892: remove the unnecessary prefix from regulator name Shawn Guo
2011-12-22 11:08 ` Mark Brown
2011-12-22 11:43 ` Shawn Guo
2011-12-21 15:00 ` [PATCH 3/4] regulator: mc13892: add device tree probe support Shawn Guo
2011-12-22 11:08 ` Mark Brown
2011-12-21 15:00 ` Shawn Guo [this message]
2011-12-30 3:28 ` [PATCH 4/4] arm/imx: add mc13892 support into imx51-babbage.dts Richard Zhao
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1324479647-4580-5-git-send-email-shawn.guo@linaro.org \
--to=shawn.guo@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).