From: shawn.guo@linaro.org (Shawn Guo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4 07/10] ASoC: fsl: make fsl_ssi driver compilable on ARM/IMX
Date: Mon, 12 Mar 2012 19:58:54 +0800 [thread overview]
Message-ID: <1331553537-19789-8-git-send-email-shawn.guo@linaro.org> (raw)
In-Reply-To: <1331553537-19789-1-git-send-email-shawn.guo@linaro.org>
Provide different pair of accessors for accessing SSI registers on
PowerPC and ARM/IMX, so that fsl_ssi driver can be built on both
architectures.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
sound/soc/fsl/fsl_ssi.c | 64 ++++++++++++++++++++++++++++++----------------
1 files changed, 42 insertions(+), 22 deletions(-)
diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c
index 2eb407f..db9a734 100644
--- a/sound/soc/fsl/fsl_ssi.c
+++ b/sound/soc/fsl/fsl_ssi.c
@@ -11,11 +11,14 @@
*/
#include <linux/init.h>
+#include <linux/io.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <linux/delay.h>
#include <linux/slab.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <sound/core.h>
@@ -26,6 +29,25 @@
#include "fsl_ssi.h"
+#ifdef PPC
+#define read_ssi(addr) in_be32(addr)
+#define write_ssi(val, addr) out_be32(addr, val)
+#define write_ssi_mask(addr, clear, set) clrsetbits_be32(addr, clear, set)
+#elif defined ARM
+#define read_ssi(addr) readl(addr)
+#define write_ssi(val, addr) writel(val, addr)
+/*
+ * FIXME: Proper locking should be added at write_ssi_mask caller level
+ * to ensure this register read/modify/write sequence is race free.
+ */
+static inline void write_ssi_mask(u32 __iomem *addr, u32 clear, u32 set)
+{
+ u32 val = readl(addr);
+ val = (val & ~clear) | set;
+ writel(val, addr);
+}
+#endif
+
/**
* FSLSSI_I2S_RATES: sample rates supported by the I2S
*
@@ -145,7 +167,7 @@ static irqreturn_t fsl_ssi_isr(int irq, void *dev_id)
were interrupted for. We mask it with the Interrupt Enable register
so that we only check for events that we're interested in.
*/
- sisr = in_be32(&ssi->sisr) & SIER_FLAGS;
+ sisr = read_ssi(&ssi->sisr) & SIER_FLAGS;
if (sisr & CCSR_SSI_SISR_RFRC) {
ssi_private->stats.rfrc++;
@@ -260,7 +282,7 @@ static irqreturn_t fsl_ssi_isr(int irq, void *dev_id)
/* Clear the bits that we set */
if (sisr2)
- out_be32(&ssi->sisr, sisr2);
+ write_ssi(sisr2, &ssi->sisr);
return ret;
}
@@ -295,7 +317,7 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream,
* SSI needs to be disabled before updating the registers we set
* here.
*/
- clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0);
/*
* Program the SSI into I2S Slave Non-Network Synchronous mode.
@@ -303,20 +325,18 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream,
*
* FIXME: Little-endian samples require a different shift dir
*/
- clrsetbits_be32(&ssi->scr,
+ write_ssi_mask(&ssi->scr,
CCSR_SSI_SCR_I2S_MODE_MASK | CCSR_SSI_SCR_SYN,
CCSR_SSI_SCR_TFR_CLK_DIS | CCSR_SSI_SCR_I2S_MODE_SLAVE
| (synchronous ? CCSR_SSI_SCR_SYN : 0));
- out_be32(&ssi->stcr,
- CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFEN0 |
+ write_ssi(CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFEN0 |
CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TEFS |
- CCSR_SSI_STCR_TSCKP);
+ CCSR_SSI_STCR_TSCKP, &ssi->stcr);
- out_be32(&ssi->srcr,
- CCSR_SSI_SRCR_RXBIT0 | CCSR_SSI_SRCR_RFEN0 |
+ write_ssi(CCSR_SSI_SRCR_RXBIT0 | CCSR_SSI_SRCR_RFEN0 |
CCSR_SSI_SRCR_RFSI | CCSR_SSI_SRCR_REFS |
- CCSR_SSI_SRCR_RSCKP);
+ CCSR_SSI_SRCR_RSCKP, &ssi->srcr);
/*
* The DC and PM bits are only used if the SSI is the clock
@@ -324,7 +344,7 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream,
*/
/* Enable the interrupts and DMA requests */
- out_be32(&ssi->sier, SIER_FLAGS);
+ write_ssi(SIER_FLAGS, &ssi->sier);
/*
* Set the watermark for transmit FIFI 0 and receive FIFO 0. We
@@ -339,9 +359,9 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream,
* make this value larger (and maybe we should), but this way
* data will be written to memory as soon as it's available.
*/
- out_be32(&ssi->sfcsr,
- CCSR_SSI_SFCSR_TFWM0(ssi_private->fifo_depth - 2) |
- CCSR_SSI_SFCSR_RFWM0(ssi_private->fifo_depth - 2));
+ write_ssi(CCSR_SSI_SFCSR_TFWM0(ssi_private->fifo_depth - 2) |
+ CCSR_SSI_SFCSR_RFWM0(ssi_private->fifo_depth - 2),
+ &ssi->sfcsr);
/*
* We keep the SSI disabled because if we enable it, then the
@@ -417,7 +437,7 @@ static int fsl_ssi_hw_params(struct snd_pcm_substream *substream,
unsigned int sample_size =
snd_pcm_format_width(params_format(hw_params));
u32 wl = CCSR_SSI_SxCCR_WL(sample_size);
- int enabled = in_be32(&ssi->scr) & CCSR_SSI_SCR_SSIEN;
+ int enabled = read_ssi(&ssi->scr) & CCSR_SSI_SCR_SSIEN;
/*
* If we're in synchronous mode, and the SSI is already enabled,
@@ -439,9 +459,9 @@ static int fsl_ssi_hw_params(struct snd_pcm_substream *substream,
/* In synchronous mode, the SSI uses STCCR for capture */
if ((substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ||
ssi_private->cpu_dai_drv.symmetric_rates)
- clrsetbits_be32(&ssi->stccr, CCSR_SSI_SxCCR_WL_MASK, wl);
+ write_ssi_mask(&ssi->stccr, CCSR_SSI_SxCCR_WL_MASK, wl);
else
- clrsetbits_be32(&ssi->srccr, CCSR_SSI_SxCCR_WL_MASK, wl);
+ write_ssi_mask(&ssi->srccr, CCSR_SSI_SxCCR_WL_MASK, wl);
return 0;
}
@@ -466,19 +486,19 @@ static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd,
case SNDRV_PCM_TRIGGER_START:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
- setbits32(&ssi->scr,
+ write_ssi_mask(&ssi->scr, 0,
CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_TE);
else
- setbits32(&ssi->scr,
+ write_ssi_mask(&ssi->scr, 0,
CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_RE);
break;
case SNDRV_PCM_TRIGGER_STOP:
case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
- clrbits32(&ssi->scr, CCSR_SSI_SCR_TE);
+ write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_TE, 0);
else
- clrbits32(&ssi->scr, CCSR_SSI_SCR_RE);
+ write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_RE, 0);
break;
default:
@@ -510,7 +530,7 @@ static void fsl_ssi_shutdown(struct snd_pcm_substream *substream,
if (!ssi_private->first_stream) {
struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
- clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0);
}
}
--
1.7.5.4
next prev parent reply other threads:[~2012-03-12 11:58 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-03-12 11:58 [PATCH v4] ASoC: add imx-sgtl5000 machine driver working with fsl_ssi Shawn Guo
2012-03-12 11:58 ` [PATCH v4 01/10] ASoC: fsl: separate SSI and DMA Kconfig options Shawn Guo
2012-03-12 11:58 ` [PATCH v4 02/10] ASoC: imx: merge sound/soc/imx into sound/soc/fsl Shawn Guo
2012-03-12 11:58 ` [PATCH v4 03/10] ASoC: fsl: rename imx-pcm Kconfig options and filename Shawn Guo
2012-03-12 11:58 ` [PATCH v4 04/10] ASoC: fsl: create fsl_utils to accommodate the common functions Shawn Guo
2012-03-12 11:58 ` [PATCH v4 05/10] ASoC: fsl: remove helper fsl_asoc_get_codec_dev_name Shawn Guo
2012-03-12 11:58 ` [PATCH v4 06/10] ASoC: fsl: check property 'compatible' for the machine name Shawn Guo
2012-03-13 23:12 ` Timur Tabi
2012-03-13 23:15 ` Mark Brown
2012-03-13 23:21 ` Shawn Guo
2012-03-12 11:58 ` Shawn Guo [this message]
2012-03-12 11:58 ` [PATCH v4 08/10] ASoC: fsl: remove the fatal error checking on codec-handle Shawn Guo
2012-03-12 11:58 ` [PATCH v4 09/10] ASoC: fsl: let fsl_ssi work with imx pcm and machine drivers Shawn Guo
2012-03-12 11:58 ` [PATCH v4 10/10] ASoC: fsl: add imx-sgtl5000 machine driver Shawn Guo
2012-03-14 9:01 ` [PATCH v4] ASoC: add imx-sgtl5000 machine driver working with fsl_ssi Sascha Hauer
2012-03-14 11:33 ` Shawn Guo
2012-03-14 23:02 ` Timur Tabi
2012-03-15 9:52 ` [alsa-devel] " Sascha Hauer
2012-03-15 10:18 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1331553537-19789-8-git-send-email-shawn.guo@linaro.org \
--to=shawn.guo@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).