[PATCH RESEND 1/2] omap3: nand: Make board_onenand_init() visible to board code

[PATCH RESEND 1/2] omap3: nand: Make board_onenand_init() visible to board code

[Javier Martinez Canillas]

board_onenand_init() and board_nand_init() initialization functions are
used to initialize OneNAND and NAND memories respectively. But only
board_nand_init() was visible to be used from board code. This patch makes
possible to initialize a OneNAND flash memory within platform code.

Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
---
 arch/arm/mach-omap2/board-flash.c |    4 ++--
 arch/arm/mach-omap2/board-flash.h |   11 +++++++++++
 2 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-omap2/board-flash.c b/arch/arm/mach-omap2/board-flash.c
index 0349fd2..70a81f9 100644
--- a/arch/arm/mach-omap2/board-flash.c
+++ b/arch/arm/mach-omap2/board-flash.c
@@ -87,7 +87,7 @@ static struct omap_onenand_platform_data board_onenand_data = {
 	.dma_channel	= -1,   /* disable DMA in OMAP OneNAND driver */
 };
 
-static void
+void
 __init board_onenand_init(struct mtd_partition *onenand_parts,
 				u8 nr_parts, u8 cs)
 {
@@ -98,7 +98,7 @@ __init board_onenand_init(struct mtd_partition *onenand_parts,
 	gpmc_onenand_init(&board_onenand_data);
 }
 #else
-static void
+void
 __init board_onenand_init(struct mtd_partition *nor_parts, u8 nr_parts, u8 cs)
 {
 }
diff --git a/arch/arm/mach-omap2/board-flash.h b/arch/arm/mach-omap2/board-flash.h
index d25503a..c44b70d 100644
--- a/arch/arm/mach-omap2/board-flash.h
+++ b/arch/arm/mach-omap2/board-flash.h
@@ -47,3 +47,14 @@ static inline void board_nand_init(struct mtd_partition *nand_parts,
 {
 }
 #endif
+
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+		defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+extern void board_onenand_init(struct mtd_partition *nand_parts,
+					u8 nr_parts, u8 cs);
+#else
+static inline void board_onenand_init(struct mtd_partition *nand_parts,
+					u8 nr_parts, u8 cs)
+{
+}
+#endif
-- 
1.7.7.6

[PATCH RESEND 2/2] OMAP3: igep0020: Add support for Micron NAND Flash storage memory

[Javier Martinez Canillas]

IGEP-based boards can have two different flash memories, a OneNAND or
a NAND device. The boot configuration pins (sys_boot) are used to
specify which memory is available. This patch is necessary in order to use
newer boards that come with NAND memories.

Also, it removes unnecesary code for registering the OneNAND.

Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
---

 arch/arm/mach-omap2/board-igep0020.c |   75 ++++++++++++++--------------------
 1 files changed, 31 insertions(+), 44 deletions(-)

diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index e558800..dbd13b2 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -24,6 +24,8 @@
 #include <linux/i2c/twl.h>
 #include <linux/mmc/host.h>
 
+#include <linux/mtd/nand.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
@@ -39,6 +41,8 @@
 #include "hsmmc.h"
 #include "sdram-numonyx-m65kxxxxam.h"
 #include "common-board-devices.h"
+#include "board-flash.h"
+#include "control.h"
 
 #define IGEP2_SMSC911X_CS       5
 #define IGEP2_SMSC911X_GPIO     176
@@ -60,6 +64,10 @@
 #define IGEP3_GPIO_LED1_RED	16
 #define IGEP3_GPIO_USBH_NRESET  183
 
+#define IGEP_SYSBOOT_MASK           0x1f
+#define IGEP_SYSBOOT_NAND           0x0f
+#define IGEP_SYSBOOT_ONENAND        0x10
+
 /*
  * IGEP2 Hardware Revision Table
  *
@@ -110,8 +118,10 @@ static void __init igep2_get_revision(void)
 	gpio_free(IGEP2_GPIO_LED1_RED);
 }
 
-#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
-	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+#if defined(CONFIG_MTD_ONENAND_OMAP2) ||		\
+	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) ||	\
+	defined(CONFIG_MTD_NAND_OMAP2) ||		\
+	defined(CONFIG_MTD_NAND_OMAP2_MODULE)
 
 #define ONENAND_MAP             0x20000000
 
@@ -123,7 +133,7 @@ static void __init igep2_get_revision(void)
  * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
  */
 
-static struct mtd_partition igep_onenand_partitions[] = {
+static struct mtd_partition igep_flash_partitions[] = {
 	{
 		.name           = "X-Loader",
 		.offset         = 0,
@@ -151,50 +161,27 @@ static struct mtd_partition igep_onenand_partitions[] = {
 	},
 };
 
-static struct omap_onenand_platform_data igep_onenand_data = {
-	.parts = igep_onenand_partitions,
-	.nr_parts = ARRAY_SIZE(igep_onenand_partitions),
-	.dma_channel	= -1,	/* disable DMA in OMAP OneNAND driver */
-};
-
-static struct platform_device igep_onenand_device = {
-	.name		= "omap2-onenand",
-	.id		= -1,
-	.dev = {
-		.platform_data = &igep_onenand_data,
-	},
-};
+static inline u32 igep_get_sysboot_value(void)
+{
+	return omap_ctrl_readl(OMAP343X_CONTROL_STATUS) & IGEP_SYSBOOT_MASK;
+}
 
 static void __init igep_flash_init(void)
 {
-	u8 cs = 0;
-	u8 onenandcs = GPMC_CS_NUM + 1;
-
-	for (cs = 0; cs < GPMC_CS_NUM; cs++) {
-		u32 ret;
-		ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
-
-		/* Check if NAND/oneNAND is configured */
-		if ((ret & 0xC00) == 0x800)
-			/* NAND found */
-			pr_err("IGEP: Unsupported NAND found\n");
-		else {
-			ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
-			if ((ret & 0x3F) == (ONENAND_MAP >> 24))
-				/* ONENAND found */
-				onenandcs = cs;
-		}
-	}
-
-	if (onenandcs > GPMC_CS_NUM) {
-		pr_err("IGEP: Unable to find configuration in GPMC\n");
-		return;
-	}
-
-	igep_onenand_data.cs = onenandcs;
-
-	if (platform_device_register(&igep_onenand_device) < 0)
-		pr_err("IGEP: Unable to register OneNAND device\n");
+	u32 mux;
+	mux = igep_get_sysboot_value();
+
+	if (mux == IGEP_SYSBOOT_NAND) {
+		pr_info("IGEP: initializing NAND memory device\n");
+		board_nand_init(igep_flash_partitions,
+				ARRAY_SIZE(igep_flash_partitions),
+				0, NAND_BUSWIDTH_16);
+	} else if (mux == IGEP_SYSBOOT_ONENAND) {
+		pr_info("IGEP: initializing OneNAND memory device\n");
+		board_onenand_init(igep_flash_partitions,
+				   ARRAY_SIZE(igep_flash_partitions), 0);
+	} else
+		pr_err("IGEP: Flash: unsupported sysboot sequence found\n");
 }
 
 #else
-- 
1.7.7.6