* [PATCH 03/10] ARM: at91: drop at91_set_serial_console
2012-04-08 15:12 [PATCH 00/10] ARM: at91: finnaly add multi soc in the same kernel support Jean-Christophe PLAGNIOL-VILLARD
2012-04-08 15:39 ` [PATCH 01/10] ARM: at91: uncompress Store UART address in a variable Jean-Christophe PLAGNIOL-VILLARD
2012-04-08 15:39 ` [PATCH 02/10] ARM: at91: uncompress: autodetect the uart to use Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-08 15:39 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-08 15:40 ` [PATCH 04/10] ARM: at91: do not pin mux the UARTs in init_early Jean-Christophe PLAGNIOL-VILLARD
` (7 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-08 15:39 UTC (permalink / raw)
To: linux-arm-kernel
at91_set_serial_console is used to define the default console of linux.
This is already manage by the cmdline. And if the boot loader can not be
modified you can still set it by enabling the CONFIG_CMDLINE_EXTEND option.
And then the command-line arguments provided by the boot loader will be
appended to the default kernel command string.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/mach-at91/at91rm9200.c | 12 ------------
arch/arm/mach-at91/at91rm9200_devices.c | 12 ------------
arch/arm/mach-at91/at91sam9260.c | 12 ------------
arch/arm/mach-at91/at91sam9260_devices.c | 12 ------------
arch/arm/mach-at91/at91sam9261.c | 12 ------------
arch/arm/mach-at91/at91sam9261_devices.c | 12 ------------
arch/arm/mach-at91/at91sam9263.c | 12 ------------
arch/arm/mach-at91/at91sam9263_devices.c | 12 ------------
arch/arm/mach-at91/at91sam9g45.c | 12 ------------
arch/arm/mach-at91/at91sam9g45_devices.c | 12 ------------
arch/arm/mach-at91/at91sam9rl.c | 12 ------------
arch/arm/mach-at91/at91sam9rl_devices.c | 12 ------------
arch/arm/mach-at91/board-1arm.c | 3 ---
arch/arm/mach-at91/board-afeb-9260v1.c | 3 ---
arch/arm/mach-at91/board-cam60.c | 3 ---
arch/arm/mach-at91/board-carmeva.c | 3 ---
arch/arm/mach-at91/board-cpu9krea.c | 3 ---
arch/arm/mach-at91/board-cpuat91.c | 3 ---
arch/arm/mach-at91/board-csb337.c | 3 ---
arch/arm/mach-at91/board-csb637.c | 3 ---
arch/arm/mach-at91/board-eb9200.c | 3 ---
arch/arm/mach-at91/board-ecbat91.c | 3 ---
arch/arm/mach-at91/board-eco920.c | 3 ---
arch/arm/mach-at91/board-flexibity.c | 3 ---
arch/arm/mach-at91/board-foxg20.c | 3 ---
arch/arm/mach-at91/board-kafa.c | 3 ---
arch/arm/mach-at91/board-kb9202.c | 3 ---
arch/arm/mach-at91/board-neocore926.c | 3 ---
arch/arm/mach-at91/board-picotux200.c | 3 ---
arch/arm/mach-at91/board-qil-a9260.c | 4 ----
arch/arm/mach-at91/board-rm9200dk.c | 3 ---
arch/arm/mach-at91/board-rm9200ek.c | 3 ---
arch/arm/mach-at91/board-rsi-ews.c | 3 ---
arch/arm/mach-at91/board-sam9-l9260.c | 3 ---
arch/arm/mach-at91/board-sam9260ek.c | 3 ---
arch/arm/mach-at91/board-sam9261ek.c | 3 ---
arch/arm/mach-at91/board-sam9263ek.c | 3 ---
arch/arm/mach-at91/board-sam9g20ek.c | 3 ---
arch/arm/mach-at91/board-sam9m10g45ek.c | 3 ---
arch/arm/mach-at91/board-sam9rlek.c | 3 ---
arch/arm/mach-at91/board-snapper9260.c | 1 -
arch/arm/mach-at91/board-stamp9g20.c | 3 ---
arch/arm/mach-at91/board-usb-a926x.c | 3 ---
arch/arm/mach-at91/board-yl-9200.c | 3 ---
arch/arm/mach-at91/generic.h | 11 -----------
arch/arm/mach-at91/include/mach/board.h | 1 -
46 files changed, 0 insertions(+), 251 deletions(-)
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index 364c193..d50da1a 100644
--- a/arch/arm/mach-at91/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -258,18 +258,6 @@ static void __init at91rm9200_register_clocks(void)
clk_register(&pck3);
}
-static struct clk_lookup console_clock_lookup;
-
-void __init at91rm9200_set_console_clock(int id)
-{
- if (id >= ARRAY_SIZE(usart_clocks_lookups))
- return;
-
- console_clock_lookup.con_id = "usart";
- console_clock_lookup.clk = usart_clocks_lookups[id].clk;
- clkdev_add(&console_clock_lookup);
-}
-
/* --------------------------------------------------------------------
* GPIO
* -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 99ce5c9..d9f0d77 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -1152,14 +1152,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
at91_uarts[portnr] = pdev;
}
-void __init at91_set_serial_console(unsigned portnr)
-{
- if (portnr < ATMEL_MAX_UART) {
- atmel_default_console_device = at91_uarts[portnr];
- at91rm9200_set_console_clock(at91_uarts[portnr]->id);
- }
-}
-
void __init at91_add_device_serial(void)
{
int i;
@@ -1168,14 +1160,10 @@ void __init at91_add_device_serial(void)
if (at91_uarts[i])
platform_device_register(at91_uarts[i]);
}
-
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
}
#else
void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index 46f7742..a27bbec 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -268,18 +268,6 @@ static void __init at91sam9260_register_clocks(void)
clk_register(&pck1);
}
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9260_set_console_clock(int id)
-{
- if (id >= ARRAY_SIZE(usart_clocks_lookups))
- return;
-
- console_clock_lookup.con_id = "usart";
- console_clock_lookup.clk = usart_clocks_lookups[id].clk;
- clkdev_add(&console_clock_lookup);
-}
-
/* --------------------------------------------------------------------
* GPIO
* -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 5652dde..ad00fe9 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -1229,14 +1229,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
at91_uarts[portnr] = pdev;
}
-void __init at91_set_serial_console(unsigned portnr)
-{
- if (portnr < ATMEL_MAX_UART) {
- atmel_default_console_device = at91_uarts[portnr];
- at91sam9260_set_console_clock(at91_uarts[portnr]->id);
- }
-}
-
void __init at91_add_device_serial(void)
{
int i;
@@ -1245,13 +1237,9 @@ void __init at91_add_device_serial(void)
if (at91_uarts[i])
platform_device_register(at91_uarts[i]);
}
-
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
}
#else
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 7de81e6..c77d503 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -239,18 +239,6 @@ static void __init at91sam9261_register_clocks(void)
clk_register(&hck1);
}
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9261_set_console_clock(int id)
-{
- if (id >= ARRAY_SIZE(usart_clocks_lookups))
- return;
-
- console_clock_lookup.con_id = "usart";
- console_clock_lookup.clk = usart_clocks_lookups[id].clk;
- clkdev_add(&console_clock_lookup);
-}
-
/* --------------------------------------------------------------------
* GPIO
* -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 4db961a..9295e90 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -1051,14 +1051,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
at91_uarts[portnr] = pdev;
}
-void __init at91_set_serial_console(unsigned portnr)
-{
- if (portnr < ATMEL_MAX_UART) {
- atmel_default_console_device = at91_uarts[portnr];
- at91sam9261_set_console_clock(at91_uarts[portnr]->id);
- }
-}
-
void __init at91_add_device_serial(void)
{
int i;
@@ -1067,13 +1059,9 @@ void __init at91_add_device_serial(void)
if (at91_uarts[i])
platform_device_register(at91_uarts[i]);
}
-
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
}
#else
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index ef301be..7fae365 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -255,18 +255,6 @@ static void __init at91sam9263_register_clocks(void)
clk_register(&pck3);
}
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9263_set_console_clock(int id)
-{
- if (id >= ARRAY_SIZE(usart_clocks_lookups))
- return;
-
- console_clock_lookup.con_id = "usart";
- console_clock_lookup.clk = usart_clocks_lookups[id].clk;
- clkdev_add(&console_clock_lookup);
-}
-
/* --------------------------------------------------------------------
* GPIO
* -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index fe99206..dfe5bc0 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -1461,14 +1461,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
at91_uarts[portnr] = pdev;
}
-void __init at91_set_serial_console(unsigned portnr)
-{
- if (portnr < ATMEL_MAX_UART) {
- atmel_default_console_device = at91_uarts[portnr];
- at91sam9263_set_console_clock(at91_uarts[portnr]->id);
- }
-}
-
void __init at91_add_device_serial(void)
{
int i;
@@ -1477,13 +1469,9 @@ void __init at91_add_device_serial(void)
if (at91_uarts[i])
platform_device_register(at91_uarts[i]);
}
-
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
}
#else
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index d222f83..f205449 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -288,18 +288,6 @@ static void __init at91sam9g45_register_clocks(void)
clk_register(&pck1);
}
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9g45_set_console_clock(int id)
-{
- if (id >= ARRAY_SIZE(usart_clocks_lookups))
- return;
-
- console_clock_lookup.con_id = "usart";
- console_clock_lookup.clk = usart_clocks_lookups[id].clk;
- clkdev_add(&console_clock_lookup);
-}
-
/* --------------------------------------------------------------------
* GPIO
* -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 6b008ae..db2f88c2 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -1741,14 +1741,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
at91_uarts[portnr] = pdev;
}
-void __init at91_set_serial_console(unsigned portnr)
-{
- if (portnr < ATMEL_MAX_UART) {
- atmel_default_console_device = at91_uarts[portnr];
- at91sam9g45_set_console_clock(at91_uarts[portnr]->id);
- }
-}
-
void __init at91_add_device_serial(void)
{
int i;
@@ -1757,13 +1749,9 @@ void __init at91_add_device_serial(void)
if (at91_uarts[i])
platform_device_register(at91_uarts[i]);
}
-
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
}
#else
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index d9f2774..e420085 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -232,18 +232,6 @@ static void __init at91sam9rl_register_clocks(void)
clk_register(&pck1);
}
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9rl_set_console_clock(int id)
-{
- if (id >= ARRAY_SIZE(usart_clocks_lookups))
- return;
-
- console_clock_lookup.con_id = "usart";
- console_clock_lookup.clk = usart_clocks_lookups[id].clk;
- clkdev_add(&console_clock_lookup);
-}
-
/* --------------------------------------------------------------------
* GPIO
* -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index fe4ae22..9c0b148 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -1192,14 +1192,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
at91_uarts[portnr] = pdev;
}
-void __init at91_set_serial_console(unsigned portnr)
-{
- if (portnr < ATMEL_MAX_UART) {
- atmel_default_console_device = at91_uarts[portnr];
- at91sam9rl_set_console_clock(at91_uarts[portnr]->id);
- }
-}
-
void __init at91_add_device_serial(void)
{
int i;
@@ -1208,13 +1200,9 @@ void __init at91_add_device_serial(void)
if (at91_uarts[i])
platform_device_register(at91_uarts[i]);
}
-
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
}
#else
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
index 2628384..f43ad91 100644
--- a/arch/arm/mach-at91/board-1arm.c
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -58,9 +58,6 @@ static void __init onearm_init_early(void)
at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata onearm_eth_data = {
diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c
index 161efba..7c7c682 100644
--- a/arch/arm/mach-at91/board-afeb-9260v1.c
+++ b/arch/arm/mach-at91/board-afeb-9260v1.c
@@ -65,9 +65,6 @@ static void __init afeb9260_init_early(void)
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2,
ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c
index c6d44ee..871717d 100644
--- a/arch/arm/mach-at91/board-cam60.c
+++ b/arch/arm/mach-at91/board-cam60.c
@@ -52,9 +52,6 @@ static void __init cam60_init_early(void)
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c
index 59d9cf9..168b3fa 100644
--- a/arch/arm/mach-at91/board-carmeva.c
+++ b/arch/arm/mach-at91/board-carmeva.c
@@ -52,9 +52,6 @@ static void __init carmeva_init_early(void)
at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata carmeva_eth_data = {
diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c
index 5f3680e..4073e30 100644
--- a/arch/arm/mach-at91/board-cpu9krea.c
+++ b/arch/arm/mach-at91/board-cpu9krea.c
@@ -77,9 +77,6 @@ static void __init cpu9krea_init_early(void)
/* USART5 on ttyS6. (Rx, Tx) */
at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c
index e094cc8..76c62ed 100644
--- a/arch/arm/mach-at91/board-cpuat91.c
+++ b/arch/arm/mach-at91/board-cpuat91.c
@@ -78,9 +78,6 @@ static void __init cpuat91_init_early(void)
/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata cpuat91_eth_data = {
diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c
index 1a1547b..d984435 100644
--- a/arch/arm/mach-at91/board-csb337.c
+++ b/arch/arm/mach-at91/board-csb337.c
@@ -53,9 +53,6 @@ static void __init csb337_init_early(void)
/* DBGU on ttyS0 */
at91_register_uart(0, 0, 0);
-
- /* make console=ttyS0 the default */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata csb337_eth_data = {
diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c
index f650bf3..0c9935d 100644
--- a/arch/arm/mach-at91/board-csb637.c
+++ b/arch/arm/mach-at91/board-csb637.c
@@ -47,9 +47,6 @@ static void __init csb637_init_early(void)
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
-
- /* make console=ttyS0 (ie, DBGU) the default */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata csb637_eth_data = {
diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c
index d302ca3..a189b9f 100644
--- a/arch/arm/mach-at91/board-eb9200.c
+++ b/arch/arm/mach-at91/board-eb9200.c
@@ -55,9 +55,6 @@ static void __init eb9200_init_early(void)
/* USART2 on ttyS2. (Rx, Tx) - IRDA */
at91_register_uart(AT91RM9200_ID_US2, 2, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata eb9200_eth_data = {
diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c
index 69966ce..307c530 100644
--- a/arch/arm/mach-at91/board-ecbat91.c
+++ b/arch/arm/mach-at91/board-ecbat91.c
@@ -59,9 +59,6 @@ static void __init ecb_at91init_early(void)
/* USART0 on ttyS1. (Rx & Tx only) */
at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata ecb_at91eth_data = {
diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c
index f23aabe..7df6a9b 100644
--- a/arch/arm/mach-at91/board-eco920.c
+++ b/arch/arm/mach-at91/board-eco920.c
@@ -43,9 +43,6 @@ static void __init eco920_init_early(void)
/* DBGU on ttyS0. (Rx & Tx only */
at91_register_uart(0, 0, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata eco920_eth_data = {
diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c
index 1815152..6dcc962 100644
--- a/arch/arm/mach-at91/board-flexibity.c
+++ b/arch/arm/mach-at91/board-flexibity.c
@@ -44,9 +44,6 @@ static void __init flexibity_init_early(void)
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/* USB Host port */
diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
index caf017f..bb07807 100644
--- a/arch/arm/mach-at91/board-foxg20.c
+++ b/arch/arm/mach-at91/board-foxg20.c
@@ -93,9 +93,6 @@ static void __init foxg20_init_early(void)
/* USART5 on ttyS6. (Rx & Tx only) */
at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
-
/* Set the internal pull-up resistor on DRXD */
at91_set_A_periph(AT91_PIN_PB14, 1);
diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
index efde1b2..3e858ed 100644
--- a/arch/arm/mach-at91/board-kafa.c
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -56,9 +56,6 @@ static void __init kafa_init_early(void)
/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata kafa_eth_data = {
diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c
index 59b92aa..ccbc8be 100644
--- a/arch/arm/mach-at91/board-kb9202.c
+++ b/arch/arm/mach-at91/board-kb9202.c
@@ -65,9 +65,6 @@ static void __init kb9202_init_early(void)
/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata kb9202_eth_data = {
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
index 57d5f6a..c456fdc 100644
--- a/arch/arm/mach-at91/board-neocore926.c
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -61,9 +61,6 @@ static void __init neocore926_init_early(void)
/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index 59e35dd..4ca56cd 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -56,9 +56,6 @@ static void __init picotux200_init_early(void)
at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata picotux200_eth_data = {
diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c
index b6ed5ed..189d3fe 100644
--- a/arch/arm/mach-at91/board-qil-a9260.c
+++ b/arch/arm/mach-at91/board-qil-a9260.c
@@ -66,10 +66,6 @@ static void __init ek_init_early(void)
/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS1 (ie, USART0) */
- at91_set_serial_console(1);
-
}
/*
diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c
index 01332aa..d5ce630 100644
--- a/arch/arm/mach-at91/board-rm9200dk.c
+++ b/arch/arm/mach-at91/board-rm9200dk.c
@@ -61,9 +61,6 @@ static void __init dk_init_early(void)
at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata dk_eth_data = {
diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c
index 11cbaa8..32d35cb 100644
--- a/arch/arm/mach-at91/board-rm9200ek.c
+++ b/arch/arm/mach-at91/board-rm9200ek.c
@@ -61,9 +61,6 @@ static void __init ek_init_early(void)
at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static struct macb_platform_data __initdata ek_eth_data = {
diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c
index af0750f..2c84463 100644
--- a/arch/arm/mach-at91/board-rsi-ews.c
+++ b/arch/arm/mach-at91/board-rsi-ews.c
@@ -52,9 +52,6 @@ static void __init rsi_ews_init_early(void)
/* USART3 on ttyS4. (Rx, Tx, RTS) */
/* RS485 communication */
at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index e8b116b..dee44cb 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -62,9 +62,6 @@ static void __init ek_init_early(void)
/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index d5aec55..6da17b5 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -65,9 +65,6 @@ static void __init ek_init_early(void)
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index c3f9944..e91c4af 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -64,9 +64,6 @@ static void __init ek_init_early(void)
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 2ffe50f..4424873 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -63,9 +63,6 @@ static void __init ek_init_early(void)
/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index 8923ec9..05f8467 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -76,9 +76,6 @@ static void __init ek_init_early(void)
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index c88e908..be2ca19 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -60,9 +60,6 @@ static void __init ek_init_early(void)
/* USART0 not connected on the -EK board */
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index b109ce2..23f383a 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -48,9 +48,6 @@ static void __init ek_init_early(void)
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c
index ebc9d01..1a6774a 100644
--- a/arch/arm/mach-at91/board-snapper9260.c
+++ b/arch/arm/mach-at91/board-snapper9260.c
@@ -46,7 +46,6 @@ static void __init snapper9260_init_early(void)
/* Debug on ttyS0 */
at91_register_uart(0, 0, 0);
- at91_set_serial_console(0);
at91_register_uart(AT91SAM9260_ID_US0, 1,
ATMEL_UART_CTS | ATMEL_UART_RTS);
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c
index 7640049..38a7ca5 100644
--- a/arch/arm/mach-at91/board-stamp9g20.c
+++ b/arch/arm/mach-at91/board-stamp9g20.c
@@ -39,9 +39,6 @@ void __init stamp9g20_init_early(void)
/* DGBU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
static void __init stamp9g20evb_init_early(void)
diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c
index b7483a3..ee482eb 100644
--- a/arch/arm/mach-at91/board-usb-a926x.c
+++ b/arch/arm/mach-at91/board-usb-a926x.c
@@ -56,9 +56,6 @@ static void __init ek_init_early(void)
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c
index 38dd279..e94a04e 100644
--- a/arch/arm/mach-at91/board-yl-9200.c
+++ b/arch/arm/mach-at91/board-yl-9200.c
@@ -75,9 +75,6 @@ static void __init yl9200_init_early(void)
/* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/*
diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h
index dd9b346..0a60bf8 100644
--- a/arch/arm/mach-at91/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -40,17 +40,6 @@ extern struct sys_timer at91sam926x_timer;
extern struct sys_timer at91x40_timer;
/* Clocks */
-/*
- * function to specify the clock of the default console. As we do not
- * use the device/driver bus, the dev_name is not intialize. So we need
- * to link the clock to a specific con_id only "usart"
- */
-extern void __init at91rm9200_set_console_clock(int id);
-extern void __init at91sam9260_set_console_clock(int id);
-extern void __init at91sam9261_set_console_clock(int id);
-extern void __init at91sam9263_set_console_clock(int id);
-extern void __init at91sam9rl_set_console_clock(int id);
-extern void __init at91sam9g45_set_console_clock(int id);
#ifdef CONFIG_AT91_PMC_UNIT
extern int __init at91_clock_init(unsigned long main_clock);
extern int __init at91_dt_clock_init(void);
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index 49a8211..369afc2 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -121,7 +121,6 @@ extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_de
#define ATMEL_UART_RI 0x20
extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
-extern void __init at91_set_serial_console(unsigned portnr);
extern struct platform_device *atmel_default_console_device;
--
1.7.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 04/10] ARM: at91: do not pin mux the UARTs in init_early
2012-04-08 15:12 [PATCH 00/10] ARM: at91: finnaly add multi soc in the same kernel support Jean-Christophe PLAGNIOL-VILLARD
` (2 preceding siblings ...)
2012-04-08 15:39 ` [PATCH 03/10] ARM: at91: drop at91_set_serial_console Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-08 15:40 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-08 15:40 ` [PATCH 05/10] ARM: at91: move at91_init_leds to board init Jean-Christophe PLAGNIOL-VILLARD
` (6 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-08 15:40 UTC (permalink / raw)
To: linux-arm-kernel
There is no need to pinmux the UART so early in the kernel.
Move it to the board init.
This will also allow to finally move the gpio driver to platform device/driver.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/mach-at91/board-1arm.c | 21 +++++-----
arch/arm/mach-at91/board-afeb-9260v1.c | 25 +++++------
arch/arm/mach-at91/board-cam60.c | 5 +-
arch/arm/mach-at91/board-carmeva.c | 15 +++----
arch/arm/mach-at91/board-cpu9krea.c | 49 +++++++++++-----------
arch/arm/mach-at91/board-cpuat91.c | 37 ++++++++---------
arch/arm/mach-at91/board-csb337.c | 5 +-
arch/arm/mach-at91/board-csb637.c | 5 +-
arch/arm/mach-at91/board-eb9200.c | 21 +++++-----
arch/arm/mach-at91/board-ecbat91.c | 11 ++---
arch/arm/mach-at91/board-eco920.c | 5 +-
arch/arm/mach-at91/board-flexibity.c | 5 +-
arch/arm/mach-at91/board-foxg20.c | 68 +++++++++++++++----------------
arch/arm/mach-at91/board-gsia18s.c | 63 ++++++++++++++--------------
arch/arm/mach-at91/board-kafa.c | 11 ++---
arch/arm/mach-at91/board-kb9202.c | 23 +++++-----
arch/arm/mach-at91/board-neocore926.c | 11 ++---
arch/arm/mach-at91/board-pcontrol-g20.c | 21 +++++-----
arch/arm/mach-at91/board-picotux200.c | 15 +++----
arch/arm/mach-at91/board-qil-a9260.c | 27 ++++++------
arch/arm/mach-at91/board-rm9200dk.c | 15 +++----
arch/arm/mach-at91/board-rm9200ek.c | 15 +++----
arch/arm/mach-at91/board-rsi-ews.c | 27 ++++++------
arch/arm/mach-at91/board-sam9-l9260.c | 21 +++++-----
arch/arm/mach-at91/board-sam9260ek.c | 21 +++++-----
arch/arm/mach-at91/board-sam9261ek.c | 5 +-
arch/arm/mach-at91/board-sam9263ek.c | 11 ++---
arch/arm/mach-at91/board-sam9g20ek.c | 21 +++++-----
arch/arm/mach-at91/board-sam9m10g45ek.c | 13 +++---
arch/arm/mach-at91/board-sam9rlek.c | 11 ++---
arch/arm/mach-at91/board-snapper9260.c | 17 ++++----
arch/arm/mach-at91/board-stamp9g20.c | 61 +++++++++++-----------------
arch/arm/mach-at91/board-usb-a926x.c | 5 +-
arch/arm/mach-at91/board-yl-9200.c | 27 ++++++------
34 files changed, 333 insertions(+), 380 deletions(-)
diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
index f43ad91..271f994 100644
--- a/arch/arm/mach-at91/board-1arm.c
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -47,17 +47,6 @@ static void __init onearm_init_early(void)
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
}
static struct macb_platform_data __initdata onearm_eth_data = {
@@ -79,6 +68,16 @@ static struct at91_udc_data __initdata onearm_udc_data = {
static void __init onearm_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&onearm_eth_data);
diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c
index 7c7c682..b7d8aa7 100644
--- a/arch/arm/mach-at91/board-afeb-9260v1.c
+++ b/arch/arm/mach-at91/board-afeb-9260v1.c
@@ -52,19 +52,6 @@ static void __init afeb9260_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1,
- ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR
- | ATMEL_UART_DCD | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2,
- ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -180,6 +167,18 @@ static struct at91_cf_data afeb9260_cf_data = {
static void __init afeb9260_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1,
+ ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR
+ | ATMEL_UART_DCD | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2,
+ ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&afeb9260_usbh_data);
diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c
index 871717d..29d3ef0 100644
--- a/arch/arm/mach-at91/board-cam60.c
+++ b/arch/arm/mach-at91/board-cam60.c
@@ -49,9 +49,6 @@ static void __init cam60_init_early(void)
{
/* Initialize processor: 10 MHz crystal */
at91_initialize(10000000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
}
/*
@@ -172,6 +169,8 @@ static void __init cam60_add_device_nand(void)
static void __init cam60_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
at91_add_device_serial();
/* SPI */
at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices));
diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c
index 168b3fa..44328a6 100644
--- a/arch/arm/mach-at91/board-carmeva.c
+++ b/arch/arm/mach-at91/board-carmeva.c
@@ -44,14 +44,6 @@ static void __init carmeva_init_early(void)
{
/* Initialize processor: 20.000 MHz crystal */
at91_initialize(20000000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
}
static struct macb_platform_data __initdata carmeva_eth_data = {
@@ -136,6 +128,13 @@ static struct gpio_led carmeva_leds[] = {
static void __init carmeva_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&carmeva_eth_data);
diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c
index 4073e30..69951ec 100644
--- a/arch/arm/mach-at91/board-cpu9krea.c
+++ b/arch/arm/mach-at91/board-cpu9krea.c
@@ -52,31 +52,6 @@ static void __init cpu9krea_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DGBU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS |
- ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
- ATMEL_UART_DCD | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS |
- ATMEL_UART_RTS);
-
- /* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS |
- ATMEL_UART_RTS);
-
- /* USART3 on ttyS4. (Rx, Tx) */
- at91_register_uart(AT91SAM9260_ID_US3, 4, 0);
-
- /* USART4 on ttyS5. (Rx, Tx) */
- at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
- /* USART5 on ttyS6. (Rx, Tx) */
- at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
}
/*
@@ -349,6 +324,30 @@ static void __init cpu9krea_board_init(void)
/* NOR */
cpu9krea_add_device_nor();
/* Serial */
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS |
+ ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
+ ATMEL_UART_DCD | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS |
+ ATMEL_UART_RTS);
+
+ /* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS |
+ ATMEL_UART_RTS);
+
+ /* USART3 on ttyS4. (Rx, Tx) */
+ at91_register_uart(AT91SAM9260_ID_US3, 4, 0);
+
+ /* USART4 on ttyS5. (Rx, Tx) */
+ at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
+
+ /* USART5 on ttyS6. (Rx, Tx) */
+ at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&cpu9krea_usbh_data);
diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c
index 76c62ed..895cf2d 100644
--- a/arch/arm/mach-at91/board-cpuat91.c
+++ b/arch/arm/mach-at91/board-cpuat91.c
@@ -59,25 +59,6 @@ static void __init cpuat91_init_early(void)
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
- ATMEL_UART_RTS);
-
- /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
- ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
- ATMEL_UART_DCD | ATMEL_UART_RI);
-
- /* USART2 on ttyS3 (Rx, Tx) */
- at91_register_uart(AT91RM9200_ID_US2, 3, 0);
-
- /* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
- ATMEL_UART_RTS);
}
static struct macb_platform_data __initdata cpuat91_eth_data = {
@@ -158,6 +139,24 @@ static struct platform_device *platform_devices[] __initdata = {
static void __init cpuat91_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
+ ATMEL_UART_RTS);
+
+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
+ ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
+ ATMEL_UART_DCD | ATMEL_UART_RI);
+
+ /* USART2 on ttyS3 (Rx, Tx) */
+ at91_register_uart(AT91RM9200_ID_US2, 3, 0);
+
+ /* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
+ ATMEL_UART_RTS);
at91_add_device_serial();
/* LEDs. */
at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds));
diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c
index d984435..ad7f9f0 100644
--- a/arch/arm/mach-at91/board-csb337.c
+++ b/arch/arm/mach-at91/board-csb337.c
@@ -50,9 +50,6 @@ static void __init csb337_init_early(void)
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
-
- /* DBGU on ttyS0 */
- at91_register_uart(0, 0, 0);
}
static struct macb_platform_data __initdata csb337_eth_data = {
@@ -226,6 +223,8 @@ static struct gpio_led csb_leds[] = {
static void __init csb337_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0 */
+ at91_register_uart(0, 0, 0);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&csb337_eth_data);
diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c
index 0c9935d..7c8b05a 100644
--- a/arch/arm/mach-at91/board-csb637.c
+++ b/arch/arm/mach-at91/board-csb637.c
@@ -44,9 +44,6 @@ static void __init csb637_init_early(void)
{
/* Initialize processor: 3.6864 MHz crystal */
at91_initialize(3686400);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
}
static struct macb_platform_data __initdata csb637_eth_data = {
@@ -115,6 +112,8 @@ static void __init csb637_board_init(void)
/* LED(s) */
at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&csb637_eth_data);
diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c
index a189b9f..bd10172 100644
--- a/arch/arm/mach-at91/board-eb9200.c
+++ b/arch/arm/mach-at91/board-eb9200.c
@@ -44,17 +44,6 @@ static void __init eb9200_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART2 on ttyS2. (Rx, Tx) - IRDA */
- at91_register_uart(AT91RM9200_ID_US2, 2, 0);
}
static struct macb_platform_data __initdata eb9200_eth_data = {
@@ -98,6 +87,16 @@ static struct i2c_board_info __initdata eb9200_i2c_devices[] = {
static void __init eb9200_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART2 on ttyS2. (Rx, Tx) - IRDA */
+ at91_register_uart(AT91RM9200_ID_US2, 2, 0);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&eb9200_eth_data);
diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c
index 307c530..2510825 100644
--- a/arch/arm/mach-at91/board-ecbat91.c
+++ b/arch/arm/mach-at91/board-ecbat91.c
@@ -53,12 +53,6 @@ static void __init ecb_at91init_early(void)
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx & Tx only) */
- at91_register_uart(AT91RM9200_ID_US0, 1, 0);
}
static struct macb_platform_data __initdata ecb_at91eth_data = {
@@ -149,6 +143,11 @@ static struct spi_board_info __initdata ecb_at91spi_devices[] = {
static void __init ecb_at91board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx & Tx only) */
+ at91_register_uart(AT91RM9200_ID_US0, 1, 0);
at91_add_device_serial();
/* Ethernet */
diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c
index 7df6a9b..bebeae8 100644
--- a/arch/arm/mach-at91/board-eco920.c
+++ b/arch/arm/mach-at91/board-eco920.c
@@ -40,9 +40,6 @@ static void __init eco920_init_early(void)
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
-
- /* DBGU on ttyS0. (Rx & Tx only */
- at91_register_uart(0, 0, 0);
}
static struct macb_platform_data __initdata eco920_eth_data = {
@@ -100,6 +97,8 @@ static struct spi_board_info eco920_spi_devices[] = {
static void __init eco920_board_init(void)
{
+ /* DBGU on ttyS0. (Rx & Tx only */
+ at91_register_uart(0, 0, 0);
at91_add_device_serial();
at91_add_device_eth(&eco920_eth_data);
at91_add_device_usbh(&eco920_usbh_data);
diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c
index 6dcc962..47658f7 100644
--- a/arch/arm/mach-at91/board-flexibity.c
+++ b/arch/arm/mach-at91/board-flexibity.c
@@ -41,9 +41,6 @@ static void __init flexibity_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
}
/* USB Host port */
@@ -140,6 +137,8 @@ static struct gpio_led flexibity_leds[] = {
static void __init flexibity_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&flexibity_usbh_data);
diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
index bb07807..33411e6 100644
--- a/arch/arm/mach-at91/board-foxg20.c
+++ b/arch/arm/mach-at91/board-foxg20.c
@@ -61,41 +61,6 @@ static void __init foxg20_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1,
- ATMEL_UART_CTS
- | ATMEL_UART_RTS
- | ATMEL_UART_DTR
- | ATMEL_UART_DSR
- | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2,
- ATMEL_UART_CTS
- | ATMEL_UART_RTS);
-
- /* USART2 on ttyS3. (Rx & Tx only) */
- at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
-
- /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9260_ID_US3, 4,
- ATMEL_UART_CTS
- | ATMEL_UART_RTS);
-
- /* USART4 on ttyS5. (Rx & Tx only) */
- at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
- /* USART5 on ttyS6. (Rx & Tx only) */
- at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-
- /* Set the internal pull-up resistor on DRXD */
- at91_set_A_periph(AT91_PIN_PB14, 1);
-
}
/*
@@ -238,6 +203,39 @@ static struct i2c_board_info __initdata foxg20_i2c_devices[] = {
static void __init foxg20_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1,
+ ATMEL_UART_CTS
+ | ATMEL_UART_RTS
+ | ATMEL_UART_DTR
+ | ATMEL_UART_DSR
+ | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2,
+ ATMEL_UART_CTS
+ | ATMEL_UART_RTS);
+
+ /* USART2 on ttyS3. (Rx & Tx only) */
+ at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
+
+ /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US3, 4,
+ ATMEL_UART_CTS
+ | ATMEL_UART_RTS);
+
+ /* USART4 on ttyS5. (Rx & Tx only) */
+ at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
+
+ /* USART5 on ttyS6. (Rx & Tx only) */
+ at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
+
+ /* Set the internal pull-up resistor on DRXD */
+ at91_set_A_periph(AT91_PIN_PB14, 1);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&foxg20_usbh_data);
diff --git a/arch/arm/mach-at91/board-gsia18s.c b/arch/arm/mach-at91/board-gsia18s.c
index 230e719..3e0dfa6 100644
--- a/arch/arm/mach-at91/board-gsia18s.c
+++ b/arch/arm/mach-at91/board-gsia18s.c
@@ -41,38 +41,6 @@
static void __init gsia18s_init_early(void)
{
stamp9g20_init_early();
-
- /*
- * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI).
- * Used for Internal Analog Modem.
- */
- at91_register_uart(AT91SAM9260_ID_US0, 1,
- ATMEL_UART_CTS | ATMEL_UART_RTS |
- ATMEL_UART_DTR | ATMEL_UART_DSR |
- ATMEL_UART_DCD | ATMEL_UART_RI);
- /*
- * USART1 on ttyS2 (Rx, Tx, CTS, RTS).
- * Used for GPS or WiFi or Data stream.
- */
- at91_register_uart(AT91SAM9260_ID_US1, 2,
- ATMEL_UART_CTS | ATMEL_UART_RTS);
- /*
- * USART2 on ttyS3 (Rx, Tx, CTS, RTS).
- * Used for External Modem.
- */
- at91_register_uart(AT91SAM9260_ID_US2, 3,
- ATMEL_UART_CTS | ATMEL_UART_RTS);
- /*
- * USART3 on ttyS4 (Rx, Tx, RTS).
- * Used for RS-485.
- */
- at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS);
-
- /*
- * USART4 on ttyS5 (Rx, Tx).
- * Used for TRX433 Radio Module.
- */
- at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
}
/*
@@ -558,6 +526,37 @@ static int __init gsia18s_power_off_init(void)
static void __init gsia18s_board_init(void)
{
+ /*
+ * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI).
+ * Used for Internal Analog Modem.
+ */
+ at91_register_uart(AT91SAM9260_ID_US0, 1,
+ ATMEL_UART_CTS | ATMEL_UART_RTS |
+ ATMEL_UART_DTR | ATMEL_UART_DSR |
+ ATMEL_UART_DCD | ATMEL_UART_RI);
+ /*
+ * USART1 on ttyS2 (Rx, Tx, CTS, RTS).
+ * Used for GPS or WiFi or Data stream.
+ */
+ at91_register_uart(AT91SAM9260_ID_US1, 2,
+ ATMEL_UART_CTS | ATMEL_UART_RTS);
+ /*
+ * USART2 on ttyS3 (Rx, Tx, CTS, RTS).
+ * Used for External Modem.
+ */
+ at91_register_uart(AT91SAM9260_ID_US2, 3,
+ ATMEL_UART_CTS | ATMEL_UART_RTS);
+ /*
+ * USART3 on ttyS4 (Rx, Tx, RTS).
+ * Used for RS-485.
+ */
+ at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS);
+
+ /*
+ * USART4 on ttyS5 (Rx, Tx).
+ * Used for TRX433 Radio Module.
+ */
+ at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
stamp9g20_board_init();
at91_add_device_usbh(&usbh_data);
at91_add_device_udc(&udc_data);
diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
index 3e858ed..f46b3eb 100644
--- a/arch/arm/mach-at91/board-kafa.c
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -50,12 +50,6 @@ static void __init kafa_init_early(void)
/* Set up the LEDs */
at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
static struct macb_platform_data __initdata kafa_eth_data = {
@@ -77,6 +71,11 @@ static struct at91_udc_data __initdata kafa_udc_data = {
static void __init kafa_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&kafa_eth_data);
diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c
index ccbc8be..e71b9e1 100644
--- a/arch/arm/mach-at91/board-kb9202.c
+++ b/arch/arm/mach-at91/board-kb9202.c
@@ -53,18 +53,6 @@ static void __init kb9202_init_early(void)
/* Set up the LEDs */
at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1 (Rx & Tx only) */
- at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-
- /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
- at91_register_uart(AT91RM9200_ID_US1, 2, 0);
-
- /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
- at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
static struct macb_platform_data __initdata kb9202_eth_data = {
@@ -113,6 +101,17 @@ static struct atmel_nand_data __initdata kb9202_nand_data = {
static void __init kb9202_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1 (Rx & Tx only) */
+ at91_register_uart(AT91RM9200_ID_US0, 1, 0);
+
+ /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
+ at91_register_uart(AT91RM9200_ID_US1, 2, 0);
+
+ /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
+ at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&kb9202_eth_data);
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
index c456fdc..d2f4cc1 100644
--- a/arch/arm/mach-at91/board-neocore926.c
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -55,12 +55,6 @@ static void __init neocore926_init_early(void)
{
/* Initialize processor: 20 MHz crystal */
at91_initialize(20000000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -338,6 +332,11 @@ static struct ac97c_platform_data neocore926_ac97_data = {
static void __init neocore926_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c
index b4a12fc..7fe6383 100644
--- a/arch/arm/mach-at91/board-pcontrol-g20.c
+++ b/arch/arm/mach-at91/board-pcontrol-g20.c
@@ -40,17 +40,6 @@
static void __init pcontrol_g20_init_early(void)
{
stamp9g20_init_early();
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
- | ATMEL_UART_RTS);
-
- /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485 X5 */
- at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
- | ATMEL_UART_RTS);
-
- /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */
- at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
}
static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
@@ -199,6 +188,16 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = {
static void __init pcontrol_g20_board_init(void)
{
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
+ | ATMEL_UART_RTS);
+
+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485 X5 */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
+ | ATMEL_UART_RTS);
+
+ /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */
+ at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
stamp9g20_board_init();
at91_add_device_usbh(&usbh_data);
at91_add_device_eth(&macb_data);
diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index 4ca56cd..b45c0a5 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -48,14 +48,6 @@ static void __init picotux200_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
}
static struct macb_platform_data __initdata picotux200_eth_data = {
@@ -103,6 +95,13 @@ static struct platform_device picotux200_flash = {
static void __init picotux200_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&picotux200_eth_data);
diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c
index 189d3fe..0c61bf0 100644
--- a/arch/arm/mach-at91/board-qil-a9260.c
+++ b/arch/arm/mach-at91/board-qil-a9260.c
@@ -52,20 +52,6 @@ static void __init ek_init_early(void)
{
/* Initialize processor: 12.000 MHz crystal */
at91_initialize(12000000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -231,6 +217,19 @@ static struct gpio_led ek_leds[] = {
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c
index d5ce630..4a0b097 100644
--- a/arch/arm/mach-at91/board-rm9200dk.c
+++ b/arch/arm/mach-at91/board-rm9200dk.c
@@ -53,14 +53,6 @@ static void __init dk_init_early(void)
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
}
static struct macb_platform_data __initdata dk_eth_data = {
@@ -188,6 +180,13 @@ static struct gpio_led dk_leds[] = {
static void __init dk_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&dk_eth_data);
diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c
index 32d35cb..b687261 100644
--- a/arch/arm/mach-at91/board-rm9200ek.c
+++ b/arch/arm/mach-at91/board-rm9200ek.c
@@ -53,14 +53,6 @@ static void __init ek_init_early(void)
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
}
static struct macb_platform_data __initdata ek_eth_data = {
@@ -159,6 +151,13 @@ static struct gpio_led ek_leds[] = {
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&ek_eth_data);
diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c
index 2c84463..10d8730 100644
--- a/arch/arm/mach-at91/board-rsi-ews.c
+++ b/arch/arm/mach-at91/board-rsi-ews.c
@@ -38,20 +38,6 @@ static void __init rsi_ews_init_early(void)
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- /* This one is for debugging */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- /* Dialin/-out modem interface */
- at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART3 on ttyS4. (Rx, Tx, RTS) */
- /* RS485 communication */
- at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
}
/*
@@ -202,6 +188,19 @@ static struct platform_device rsiews_nor_flash = {
static void __init rsi_ews_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ /* This one is for debugging */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ /* Dialin/-out modem interface */
+ at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART3 on ttyS4. (Rx, Tx, RTS) */
+ /* RS485 communication */
+ at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
at91_add_device_serial();
at91_set_gpio_output(AT91_PIN_PA21, 0);
/* Ethernet */
diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index dee44cb..5343dab 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -51,17 +51,6 @@ static void __init ek_init_early(void)
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -182,6 +171,16 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index 6da17b5..7b3c391 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -54,17 +54,6 @@ static void __init ek_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -317,6 +306,16 @@ static void __init ek_add_device_buttons(void) {}
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index e91c4af..4406f6b 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -61,9 +61,6 @@ static void __init ek_init_early(void)
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
}
/*
@@ -574,6 +571,8 @@ static struct gpio_led ek_leds[] = {
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 4424873..983cb98 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -57,12 +57,6 @@ static void __init ek_init_early(void)
{
/* Initialize processor: 16.367 MHz crystal */
at91_initialize(16367660);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -409,6 +403,11 @@ static struct at91_can_data ek_can_data = {
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index 05f8467..3d61553 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -65,17 +65,6 @@ static void __init ek_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -369,6 +358,16 @@ static struct i2c_board_info __initdata ek_i2c_devices[] = {
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index be2ca19..9a87f0b 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -53,13 +53,6 @@ static void __init ek_init_early(void)
{
/* Initialize processor: 12.000 MHz crystal */
at91_initialize(12000000);
-
- /* DGBU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 not connected on the -EK board */
- /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -454,6 +447,12 @@ static struct platform_device *devices[] __initdata = {
static void __init ek_board_init(void)
{
/* Serial */
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 not connected on the -EK board */
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB HS Host */
at91_add_device_usbh_ohci(&ek_usbh_hs_data);
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index 23f383a..be3239f 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -42,12 +42,6 @@ static void __init ek_init_early(void)
{
/* Initialize processor: 12.000 MHz crystal */
at91_initialize(12000000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
}
/*
@@ -293,6 +287,11 @@ static void __init ek_add_device_buttons(void) {}
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB HS */
at91_add_device_usba(&ek_usba_udc_data);
diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c
index 1a6774a..9d446f1 100644
--- a/arch/arm/mach-at91/board-snapper9260.c
+++ b/arch/arm/mach-at91/board-snapper9260.c
@@ -43,15 +43,6 @@
static void __init snapper9260_init_early(void)
{
at91_initialize(18432000);
-
- /* Debug on ttyS0 */
- at91_register_uart(0, 0, 0);
-
- at91_register_uart(AT91SAM9260_ID_US0, 1,
- ATMEL_UART_CTS | ATMEL_UART_RTS);
- at91_register_uart(AT91SAM9260_ID_US1, 2,
- ATMEL_UART_CTS | ATMEL_UART_RTS);
- at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
}
static struct at91_usbh_data __initdata snapper9260_usbh_data = {
@@ -167,6 +158,14 @@ static void __init snapper9260_board_init(void)
snapper9260_i2c_isl1208.irq = gpio_to_irq(AT91_PIN_PA31);
i2c_register_board_info(0, &snapper9260_i2c_isl1208, 1);
+ /* Debug on ttyS0 */
+ at91_register_uart(0, 0, 0);
+
+ at91_register_uart(AT91SAM9260_ID_US0, 1,
+ ATMEL_UART_CTS | ATMEL_UART_RTS);
+ at91_register_uart(AT91SAM9260_ID_US1, 2,
+ ATMEL_UART_CTS | ATMEL_UART_RTS);
+ at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
at91_add_device_serial();
at91_add_device_usbh(&snapper9260_usbh_data);
at91_add_device_udc(&snapper9260_udc_data);
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c
index 38a7ca5..ee86f9d 100644
--- a/arch/arm/mach-at91/board-stamp9g20.c
+++ b/arch/arm/mach-at91/board-stamp9g20.c
@@ -36,41 +36,6 @@ void __init stamp9g20_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
-
- /* DGBU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-}
-
-static void __init stamp9g20evb_init_early(void)
-{
- stamp9g20_init_early();
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR
- | ATMEL_UART_DCD | ATMEL_UART_RI);
-}
-
-static void __init portuxg20_init_early(void)
-{
- stamp9g20_init_early();
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR
- | ATMEL_UART_DCD | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* USART4 on ttyS5. (Rx, Tx only) */
- at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
- /* USART5 on ttyS6. (Rx, Tx only) */
- at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
}
/*
@@ -251,6 +216,8 @@ void add_w1(void)
void __init stamp9g20_board_init(void)
{
/* Serial */
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
at91_add_device_serial();
/* NAND */
add_device_nand();
@@ -266,6 +233,22 @@ void __init stamp9g20_board_init(void)
static void __init portuxg20_board_init(void)
{
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR
+ | ATMEL_UART_DCD | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* USART4 on ttyS5. (Rx, Tx only) */
+ at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
+
+ /* USART5 on ttyS6. (Rx, Tx only) */
+ at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
stamp9g20_board_init();
/* USB Host */
at91_add_device_usbh(&usbh_data);
@@ -283,6 +266,10 @@ static void __init portuxg20_board_init(void)
static void __init stamp9g20evb_board_init(void)
{
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR
+ | ATMEL_UART_DCD | ATMEL_UART_RI);
stamp9g20_board_init();
/* USB Host */
at91_add_device_usbh(&usbh_data);
@@ -300,7 +287,7 @@ MACHINE_START(PORTUXG20, "taskit PortuxG20")
/* Maintainer: taskit GmbH */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
- .init_early = portuxg20_init_early,
+ .init_early = stamp9g20_init_early,
.init_irq = at91_init_irq_default,
.init_machine = portuxg20_board_init,
MACHINE_END
@@ -309,7 +296,7 @@ MACHINE_START(STAMP9G20, "taskit Stamp9G20")
/* Maintainer: taskit GmbH */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
- .init_early = stamp9g20evb_init_early,
+ .init_early = stamp9g20_init_early,
.init_irq = at91_init_irq_default,
.init_machine = stamp9g20evb_board_init,
MACHINE_END
diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c
index ee482eb..332ecd4 100644
--- a/arch/arm/mach-at91/board-usb-a926x.c
+++ b/arch/arm/mach-at91/board-usb-a926x.c
@@ -53,9 +53,6 @@ static void __init ek_init_early(void)
{
/* Initialize processor: 12.00 MHz crystal */
at91_initialize(12000000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
}
/*
@@ -322,6 +319,8 @@ static void __init ek_add_device_leds(void)
static void __init ek_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c
index e94a04e..db8d25c 100644
--- a/arch/arm/mach-at91/board-yl-9200.c
+++ b/arch/arm/mach-at91/board-yl-9200.c
@@ -61,20 +61,6 @@ static void __init yl9200_init_early(void)
/* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */
at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART0 on ttyS2. (Rx & Tx only to JP3) */
- at91_register_uart(AT91RM9200_ID_US0, 2, 0);
-
- /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
- at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
}
/*
@@ -558,6 +544,19 @@ void __init yl9200_add_device_video(void) {}
static void __init yl9200_board_init(void)
{
/* Serial */
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART0 on ttyS2. (Rx & Tx only to JP3) */
+ at91_register_uart(AT91RM9200_ID_US0, 2, 0);
+
+ /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
+ at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&yl9200_eth_data);
--
1.7.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread