From: t-kristo@ti.com (Tero Kristo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 05/19] ARM: OMAP4: PM: Add SAR backup support towards device OFF
Date: Wed, 25 Apr 2012 10:18:29 +0300 [thread overview]
Message-ID: <1335338309.2149.96.camel@sokoban> (raw)
In-Reply-To: <20120424163547.GL3739@atomide.com>
On Tue, 2012-04-24 at 09:35 -0700, Tony Lindgren wrote:
> * Tero Kristo <t-kristo@ti.com> [120420 02:39]:
> > +
> > +static int omap4_sar_not_accessible(void)
> > +{
> > + u32 usbhost_state, usbtll_state;
> > +
> > + /*
> > + * Make sure that USB host and TLL modules are not
> > + * enabled before attempting to save the context
> > + * registers, otherwise this will trigger an exception.
> > + */
> > + usbhost_state = omap4_cminst_read_inst_reg(OMAP4430_CM2_PARTITION,
> > + OMAP4430_CM2_L3INIT_INST,
> > + OMAP4_CM_L3INIT_USB_HOST_CLKCTRL_OFFSET)
> > + & (OMAP4430_STBYST_MASK | OMAP4430_IDLEST_MASK);
> > +
> > + usbtll_state = omap4_cminst_read_inst_reg(OMAP4430_CM2_PARTITION,
> > + OMAP4430_CM2_L3INIT_INST,
> > + OMAP4_CM_L3INIT_USB_TLL_CLKCTRL_OFFSET)
> > + & OMAP4430_IDLEST_MASK;
>
> Formatting here looks bad, maybe just do it in separate steps:
>
> usbhost_state = omap4_cminst...
> usbhost_state &= OMAP4430_STBYST_MASK | OMAP4430_IDLEST_MASK;
> ...
>
>
> > + /*
> > + * Not supported on ES1.0 silicon
> > + */
> > + if (omap_rev() == OMAP4430_REV_ES1_0) {
> > + WARN_ONCE(1, "omap4: SAR backup not supported on ES1.0 ..\n");
> > + return -ENODEV;
> > + }
>
> Everytime there's SoC/hardware revision detection in a non __init function,
> something is most likely wrong.
>
>
> > +void omap4_sar_overwrite(void)
> > +{
> > + u32 val = 0;
> > + u32 offset = 0;
> > +
> > + if (cpu_is_omap446x())
> > + offset = 0x04;
>
> Here too.
>
>
> > +static int __init omap4_sar_ram_init(void)
> > +{
> > + /*
> > + * To avoid code running on other OMAPs in
> > + * multi-omap builds
> > + */
> > + if (!cpu_is_omap44xx())
> > + return -ENODEV;
>
> You should configure things here instead by setting function
> pointers or variables.
>
> Regards,
>
> Tony
Okay, I can drop rest of these from this patch, most of them do not
exist in the final code (removed by later patches for autogeneration), I
just left this here for historical reasons.
-Tero
next prev parent reply other threads:[~2012-04-25 7:18 UTC|newest]
Thread overview: 63+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-20 9:33 [PATCH 00/19] ARM: OMAP4 device off support Tero Kristo
2012-04-20 9:33 ` [PATCH 01/19] ARM: OMAP4: PM: save/restore all DPLL settings in OFF mode Tero Kristo
2012-04-23 16:09 ` Jon Hunter
2012-04-25 7:33 ` Tero Kristo
2012-04-25 15:12 ` Jon Hunter
2012-05-04 19:22 ` Tony Lindgren
2012-05-02 10:10 ` Bedia, Vaibhav
2012-05-02 10:18 ` Shilimkar, Santosh
2012-05-02 10:55 ` Bedia, Vaibhav
2012-05-02 11:00 ` Shilimkar, Santosh
2012-05-02 11:40 ` Bedia, Vaibhav
2012-05-02 11:46 ` Shilimkar, Santosh
2012-05-02 11:55 ` Bedia, Vaibhav
2012-05-02 11:47 ` Menon, Nishanth
2012-05-02 11:55 ` Bedia, Vaibhav
2012-05-02 11:58 ` Shilimkar, Santosh
2012-05-02 12:10 ` Bedia, Vaibhav
2012-04-20 9:33 ` [PATCH 02/19] ARM: OMAP4: PM: save/restore all CM1/2 " Tero Kristo
2012-05-09 23:27 ` Kevin Hilman
2012-05-11 14:30 ` Tero Kristo
2012-04-20 9:33 ` [PATCH 03/19] ARM: OMAP4: PM: powerdomain: Add HWSAR flag to L3INIT Tero Kristo
2012-04-20 9:33 ` [PATCH 04/19] ARM: OMAP4: Add SAR ROM base address Tero Kristo
2012-04-20 9:33 ` [PATCH 05/19] ARM: OMAP4: PM: Add SAR backup support towards device OFF Tero Kristo
2012-04-24 16:35 ` Tony Lindgren
2012-04-25 7:18 ` Tero Kristo [this message]
2012-04-20 9:33 ` [PATCH 06/19] ARM: OMAP4: Auto generate SAR layout contents Tero Kristo
2012-04-24 16:37 ` Tony Lindgren
2012-04-20 9:33 ` [PATCH 07/19] ARM: OMAP4: SAR: generate overwrite data based on SAR ROM contents Tero Kristo
2012-04-20 9:33 ` [PATCH 08/19] ARM: OMAP4: PM: Add device-off support Tero Kristo
2012-04-24 17:46 ` Jon Hunter
2012-04-25 7:30 ` Tero Kristo
2012-04-20 9:33 ` [PATCH 09/19] ARM: OMAP4: PM: add errata support Tero Kristo
2012-04-20 9:33 ` [PATCH 10/19] ARM: OMAP4: PM: Work-around for ROM code BUG of IVAHD/TESLA Tero Kristo
2012-04-24 17:50 ` Jon Hunter
2012-04-25 7:31 ` Tero Kristo
2012-04-20 9:33 ` [PATCH 11/19] ARM: OMAP4: PM: save/restore CM L3INSTR registers when MPU hits OSWR/OFF mode Tero Kristo
2012-04-24 17:57 ` Jon Hunter
2012-04-25 7:31 ` Tero Kristo
2012-04-20 9:33 ` [PATCH 12/19] ARM: OMAP4: PM: update ROM return address for OSWR and OFF Tero Kristo
2012-04-24 16:39 ` Tony Lindgren
2012-04-25 7:24 ` Tero Kristo
2012-04-20 9:33 ` [PATCH 13/19] ARM: OMAP4: PM: Mark the PPI and SPI interrupts as non-secure for GP Tero Kristo
2012-04-20 9:33 ` [PATCH 14/19] ARM: OMAP4: wakeupgen: enable clocks for save_secure_all Tero Kristo
2012-04-20 9:33 ` [PATCH 15/19] ARM: OMAP4430: PM: workaround for DDR corruption on second CS Tero Kristo
2012-04-24 18:22 ` Jon Hunter
2012-04-25 7:26 ` Tero Kristo
2012-04-25 7:59 ` Shilimkar, Santosh
2012-04-25 15:16 ` Jon Hunter
2012-04-26 6:19 ` Shilimkar, Santosh
2012-04-20 9:33 ` [PATCH 16/19] TEMP: ARM: OMAP4: prevent voltage transitions Tero Kristo
2012-04-20 9:33 ` [PATCH 17/19] ARM: OMAP4: put cpu1 back to sleep if no wake request Tero Kristo
2012-04-20 9:33 ` [PATCH 18/19] ARM: OMAP4460: wakeupgen: set GIC_CPU0 backup status flag always Tero Kristo
2012-04-20 9:33 ` [PATCH 19/19] ARM: OMAP4: powerdomain: update mpu / core off counters during device off Tero Kristo
2012-04-20 12:20 ` [PATCH 00/19] ARM: OMAP4 device off support T Krishnamoorthy, Balaji
2012-04-20 12:58 ` Tero Kristo
2012-04-20 13:55 ` Kevin Hilman
2012-04-20 14:43 ` Tero Kristo
2012-04-20 14:51 ` Datta, Shubhrajyoti
2012-04-20 15:07 ` Tero Kristo
2012-04-23 6:28 ` Shubhrajyoti Datta
2012-05-09 22:46 ` Kevin Hilman
2012-05-09 23:14 ` Russell King - ARM Linux
2012-05-10 9:47 ` Tero Kristo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1335338309.2149.96.camel@sokoban \
--to=t-kristo@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).