linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: lee.jones@linaro.org (Lee Jones)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 09/16] ARM: ux500: Provide regulator support for SMSC911x via Device Tree
Date: Fri, 18 May 2012 09:39:08 +0100	[thread overview]
Message-ID: <1337330355-17747-10-git-send-email-lee.jones@linaro.org> (raw)
In-Reply-To: <1337330355-17747-1-git-send-email-lee.jones@linaro.org>

This patch adds a fixed regulator for use by the SMSC911x Ethernet
chip driver into the db8500 Device Tree. It also references other
regulators required by the same device.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 arch/arm/boot/dts/snowball.dts   |   13 +++++++++++++
 arch/arm/configs/u8500_defconfig |    1 +
 drivers/mfd/db8500-prcmu.c       |    1 +
 3 files changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/snowball.dts b/arch/arm/boot/dts/snowball.dts
index 15ee419..ae3c367 100644
--- a/arch/arm/boot/dts/snowball.dts
+++ b/arch/arm/boot/dts/snowball.dts
@@ -20,6 +20,16 @@
 		reg = <0x00000000 0x20000000>;
 	};
 
+	en_3v3_reg: en_3v3 {
+		compatible = "regulator-fixed";
+                regulator-name = "en-3v3-fixed-supply";
+                regulator-min-microvolt = <3300000>;
+                regulator-max-microvolt = <3300000>;
+                gpios = <&gpio0 26  0x4>; // 26
+                startup-delay-us = <5000>;
+                enable-active-high;
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
@@ -81,6 +91,9 @@
 				reg = <0 0x10000>;
 				interrupts = <12 0x1>;
 				interrupt-parent = <&gpio4>;
+				vdd33a-supply = <&en_3v3_reg>;
+				vddvario-supply = <&db8500_vape_reg>;
+
 
 				reg-shift = <1>;
 				reg-io-width = <2>;
diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index c6973c5..440152a 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -75,6 +75,7 @@ CONFIG_AB5500_CORE=y
 CONFIG_AB8500_CORE=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_AB8500=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
 # CONFIG_HID_SUPPORT is not set
 CONFIG_USB_GADGET=y
 CONFIG_AB8500_USB=y
diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index d534449..40204e1 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -2735,6 +2735,7 @@ static struct regulator_consumer_supply db8500_vape_consumers[] = {
 	REGULATOR_SUPPLY("vcore", "uart2"),
 	REGULATOR_SUPPLY("v-ape", "nmk-ske-keypad.0"),
 	REGULATOR_SUPPLY("v-hsi", "ste_hsi.0"),
+	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
 };
 
 static struct regulator_consumer_supply db8500_vsmps2_consumers[] = {
-- 
1.7.9.5

  parent reply	other threads:[~2012-05-18  8:39 UTC|newest]

Thread overview: 50+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-05-18  8:38 [PATCH 00/16] The last large installment of DT for Snowball Lee Jones
2012-05-18  8:39 ` [PATCH 01/16] Input: Add Device Tree support to the ab8500-ponkey driver Lee Jones
2012-05-21 21:32   ` Linus Walleij
2012-06-12  7:22     ` Dmitry Torokhov
2012-05-18  8:39 ` [PATCH 02/16] ARM: ux500: Enable LED heartbeat functionality on Snowball Lee Jones
2012-05-21 21:33   ` Linus Walleij
2012-05-22  7:38     ` Lee Jones
2012-05-18  8:39 ` [PATCH 03/16] ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT Lee Jones
2012-05-21 21:34   ` Linus Walleij
2012-05-18  8:39 ` [PATCH 04/16] ARM: ux500: Only initialise STE's UIBs on boards which support them Lee Jones
2012-05-21 21:36   ` Linus Walleij
2012-05-22  7:39     ` Lee Jones
2012-05-18  8:39 ` [PATCH 05/16] regulator: db8500-prcmu: Separate regulator registration from probe Lee Jones
2012-05-18 15:36   ` Mark Brown
2012-05-21  6:58   ` Linus Walleij
2012-05-18  8:39 ` [PATCH 06/16] ARM: ux500: Apply db8500-prcmu regulator information to db8500 Device Tree Lee Jones
2012-05-21 21:37   ` Linus Walleij
2012-05-22  7:41     ` Lee Jones
2012-05-29  1:51   ` Linus Walleij
2012-05-18  8:39 ` [PATCH 07/16] regulator: Enable Device Tree for the db8500-prcmu regulator driver Lee Jones
2012-05-18 15:36   ` Mark Brown
2012-05-21  6:59   ` Linus Walleij
2012-05-18  8:39 ` [PATCH 08/16] ARM: ux500: Allow PRCMU regulator to be probed during a DT enabled boot Lee Jones
2012-05-21 21:37   ` Linus Walleij
2012-05-18  8:39 ` Lee Jones [this message]
2012-05-21 21:42   ` [PATCH 09/16] ARM: ux500: Provide regulator support for SMSC911x via Device Tree Linus Walleij
2012-05-22  6:44     ` Arnd Bergmann
2012-05-22  7:46     ` Lee Jones
2012-05-18  8:39 ` [PATCH 10/16] ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl Lee Jones
2012-05-21 21:43   ` Linus Walleij
2012-05-18  8:39 ` [PATCH 11/16] mfd: Enable Device Tree support in the ab8500-sysctrl driver Lee Jones
2012-05-19 15:35   ` Samuel Ortiz
2012-05-18  8:39 ` [PATCH 12/16] ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm Lee Jones
2012-05-21 21:43   ` Linus Walleij
2012-05-18  8:39 ` [PATCH 13/16] mfd: Enable Device Tree support in the ab8500-pwm driver Lee Jones
2012-05-19 15:35   ` Samuel Ortiz
2012-05-18  8:39 ` [PATCH 14/16] ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices Lee Jones
2012-05-21 21:44   ` Linus Walleij
2012-05-18  8:39 ` [PATCH 15/16] ARM: ux500: Add regulator support for nomadik-i2c into the db8500 Device Tree Lee Jones
2012-05-21 21:45   ` Linus Walleij
2012-05-22  8:00     ` Lee Jones
2012-05-29  1:53       ` Linus Walleij
2012-05-29  4:50         ` Lee Jones
2012-05-30  0:09           ` Linus Walleij
2012-05-30  0:33             ` Lee Jones
2012-05-30  2:51               ` Linus Walleij
2012-05-18  8:39 ` [PATCH 16/16] ARM: ux500: Re-enable SMSC911x platform code registration during non-DT boots Lee Jones
2012-05-21 21:46   ` Linus Walleij
2012-05-22  8:01     ` Lee Jones
2012-05-29  1:54       ` Linus Walleij

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1337330355-17747-10-git-send-email-lee.jones@linaro.org \
    --to=lee.jones@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).