From: stigge@antcom.de (Roland Stigge)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 01/23] ARM: LPC32xx: Add NAND flash timing to PHY3250 board dts
Date: Thu, 14 Jun 2012 18:50:51 +0200 [thread overview]
Message-ID: <1339692673-7848-2-git-send-email-stigge@antcom.de> (raw)
In-Reply-To: <1339692673-7848-1-git-send-email-stigge@antcom.de>
This patch adds necessary NAND flash timings to the board specific dts file of
the PHY3250 reference board of the LPC32xx SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
---
arch/arm/boot/dts/phy3250.dts | 11 +++++++++++
1 file changed, 11 insertions(+)
--- linux-2.6.orig/arch/arm/boot/dts/phy3250.dts
+++ linux-2.6/arch/arm/boot/dts/phy3250.dts
@@ -54,6 +54,17 @@
#address-cells = <1>;
#size-cells = <1>;
+ nxp,wdr-clks = <14>;
+ nxp,wwidth = <40000000>;
+ nxp,whold = <100000000>;
+ nxp,wsetup = <100000000>;
+ nxp,rdr-clks = <14>;
+ nxp,rwidth = <40000000>;
+ nxp,rhold = <66666666>;
+ nxp,rsetup = <100000000>;
+ nand-on-flash-bbt;
+ gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
mtd0 at 00000000 {
label = "phy3250-boot";
reg = <0x00000000 0x00064000>;
next prev parent reply other threads:[~2012-06-14 16:50 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-06-14 16:50 [PATCH v2 00/23] ARM: LPC32xx specific updates for next Roland Stigge
2012-06-14 16:50 ` Roland Stigge [this message]
2012-06-14 16:50 ` [PATCH v2 02/23] ARM: LPC32xx: Clock initialization for NAND controllers Roland Stigge
2012-06-14 16:50 ` [PATCH v2 03/23] ARM: LPC32xx: Remove SLC controller initialization from platform init Roland Stigge
2012-06-14 16:50 ` [PATCH v2 04/23] ARM: LPC32xx: Add DMA configuration to platform data Roland Stigge
2012-07-10 21:36 ` Arnd Bergmann
2012-07-11 8:28 ` Roland Stigge
2012-07-11 12:33 ` Arnd Bergmann
2012-07-11 12:40 ` Roland Stigge
2012-07-11 13:25 ` Arnd Bergmann
2012-07-11 13:39 ` Roland Stigge
2012-06-14 16:50 ` [PATCH v2 05/23] ARM: LPC32xx: Adjust dtsi file for MLC controller configuration Roland Stigge
2012-06-14 16:50 ` [PATCH v2 06/23] ARM: LPC32xx: Add dts for EA3250 reference board Roland Stigge
2012-06-14 16:50 ` [PATCH v2 07/23] ARM: LPC32xx: DTS adjustment for key matrix controller Roland Stigge
2012-06-14 16:50 ` [PATCH v2 08/23] ARM: LPC32xx: Clock " Roland Stigge
2012-06-14 16:50 ` [PATCH v2 09/23] ARM: LPC32xx: Defconfig update Roland Stigge
2012-06-14 16:51 ` [PATCH v2 10/23] ARM: LPC32xx: Add MMC controller support Roland Stigge
2012-06-14 16:51 ` [PATCH v2 11/23] ARM: LPC32xx: DTS adjustment for using pl18x primecell Roland Stigge
2012-06-14 16:51 ` [PATCH v2 12/23] ARM: LPC32xx: DT conversion of Standard UARTs Roland Stigge
2012-06-14 16:51 ` [PATCH v2 13/23] ARM: LPC32xx: High Speed UART configuration via DT Roland Stigge
2012-06-14 16:51 ` [PATCH v2 14/23] ARM: LPC32xx: Remove mach specific ARCH_NR_GPIOS, use default Roland Stigge
2012-06-14 16:51 ` [PATCH v2 15/23] ARM: LPC32xx: Fix lpc32xx.dtsi status property: "disable" -> "disabled" Roland Stigge
2012-06-14 16:51 ` [PATCH v2 16/23] ARM: LPC32xx: Build arch dtbs Roland Stigge
2012-06-14 16:51 ` [PATCH v2 17/23] ARM: LPC32xx: Add dt settings to the at25 node Roland Stigge
2012-06-14 16:51 ` [PATCH v2 18/23] ARM: LPC32xx: Remove spi chipselect request from board init Roland Stigge
2012-06-14 16:51 ` [PATCH v2 19/23] ARM: LPC32xx: Remove spi chip definitions Roland Stigge
2012-06-14 16:51 ` [PATCH v2 20/23] ARM: LPC32xx: Cleanup board init, remove duplicate clock init Roland Stigge
2012-06-14 16:51 ` [PATCH v2 21/23] ARM: LPC32xx: Move uart6 irda disable to serial.c Roland Stigge
2012-06-14 16:51 ` [PATCH v2 22/23] ARM: LPC32xx: Move i2s1 dma enabling to clock.c Roland Stigge
2012-06-14 16:51 ` [PATCH v2 23/23] ARM: LPC32xx: Remove duplicate usb host clock init Roland Stigge
2012-06-15 12:07 ` [PATCH v2 00/23] ARM: LPC32xx specific updates for next Arnd Bergmann
2012-06-15 12:12 ` Alexandre Pereira da Silva
2012-06-15 12:37 ` Roland Stigge
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1339692673-7848-2-git-send-email-stigge@antcom.de \
--to=stigge@antcom.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).