* [PATCH 0/2] omap: add ocp2scp as a bus driver @ 2012-07-16 14:13 Kishon Vijay Abraham I 2012-07-16 14:13 ` [PATCH 1/2] drivers: bus: add a new driver for omap-ocp2scp Kishon Vijay Abraham I 2012-07-16 14:13 ` [PATCH 2/2] arm/dts: omap4: Add ocp2scp data Kishon Vijay Abraham I 0 siblings, 2 replies; 7+ messages in thread From: Kishon Vijay Abraham I @ 2012-07-16 14:13 UTC (permalink / raw) To: linux-arm-kernel This patch series is done as a preparatory step for adding phy drivers for dwc3 and musb. This series adds a new driver for ocp2scp (only dt) to which phy drivers are connected. Since currently there is no generic way to create a child device along with doing a pm_runtime_enable (the exact requirement for ocp2scp), I'm creating a separate driver for ocp2scp. Changes from [RFC PATCH v2 0/2] omap: add ocp2scp as a misc driver: Created a new folder drivers/bus and moved ocp2scp driver from misc to drivers/bus. This patch was developed and tested on git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git Kishon Vijay Abraham I (2): drivers: bus: add a new driver for omap-ocp2scp arm/dts: omap4: Add ocp2scp data .../devicetree/bindings/bus/omap-ocp2scp.txt | 10 ++ arch/arm/boot/dts/omap4.dtsi | 8 ++ drivers/Kconfig | 2 + drivers/Makefile | 2 + drivers/bus/Kconfig | 15 +++ drivers/bus/Makefile | 5 + drivers/bus/omap-ocp2scp.c | 98 ++++++++++++++++++++ 7 files changed, 140 insertions(+), 0 deletions(-) create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt create mode 100644 drivers/bus/Kconfig create mode 100644 drivers/bus/Makefile create mode 100644 drivers/bus/omap-ocp2scp.c -- 1.7.5.4 ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 1/2] drivers: bus: add a new driver for omap-ocp2scp 2012-07-16 14:13 [PATCH 0/2] omap: add ocp2scp as a bus driver Kishon Vijay Abraham I @ 2012-07-16 14:13 ` Kishon Vijay Abraham I 2012-07-17 5:13 ` ABRAHAM, KISHON VIJAY 2012-07-16 14:13 ` [PATCH 2/2] arm/dts: omap4: Add ocp2scp data Kishon Vijay Abraham I 1 sibling, 1 reply; 7+ messages in thread From: Kishon Vijay Abraham I @ 2012-07-16 14:13 UTC (permalink / raw) To: linux-arm-kernel Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of creating all the devices that is connected to OCP2SCP. In the case of OMAP4, USB2PHY is connected to ocp2scp. This also includes device tree support for ocp2scp driver and the documentation with device tree binding information is updated. Cc: Felipe Balbi <balbi@ti.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- .../devicetree/bindings/bus/omap-ocp2scp.txt | 10 ++ drivers/Kconfig | 2 + drivers/Makefile | 2 + drivers/bus/Kconfig | 15 +++ drivers/bus/Makefile | 5 + drivers/bus/omap-ocp2scp.c | 98 ++++++++++++++++++++ 6 files changed, 132 insertions(+), 0 deletions(-) create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt create mode 100644 drivers/bus/Kconfig create mode 100644 drivers/bus/Makefile create mode 100644 drivers/bus/omap-ocp2scp.c diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt new file mode 100644 index 0000000..d2fe064 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt @@ -0,0 +1,10 @@ +* OMAP OCP2SCP - ocp interface to scp interface + +properties: +- compatible : Should be "ti,omap-ocp2scp" +- #address-cells, #size-cells : Must be present if the device has sub-nodes +- ranges : the child address space are mapped 1:1 onto the parent address space +- ti,hwmods : must be "ocp2scp_usb_phy" + +Sub-nodes: +All the devices connected to ocp2scp are described using sub-node to ocp2scp diff --git a/drivers/Kconfig b/drivers/Kconfig index bfc9186..4fe1e4c 100644 --- a/drivers/Kconfig +++ b/drivers/Kconfig @@ -2,6 +2,8 @@ menu "Device Drivers" source "drivers/base/Kconfig" +source "drivers/bus/Kconfig" + source "drivers/connector/Kconfig" source "drivers/mtd/Kconfig" diff --git a/drivers/Makefile b/drivers/Makefile index 2ba29ff..cac3819 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -5,6 +5,8 @@ # Rewritten to use lists instead of if-statements. # +obj-y += bus/ + # GPIO must come after pinctrl as gpios may need to mux pins etc obj-y += pinctrl/ obj-y += gpio/ diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig new file mode 100644 index 0000000..6270415 --- /dev/null +++ b/drivers/bus/Kconfig @@ -0,0 +1,15 @@ +# +# Bus Devices +# + +menu "Bus devices" + +config OMAP_OCP2SCP + tristate "OMAP OCP2SCP DRIVER" + help + Driver to enable ocp2scp module which transforms ocp interface + protocol to scp protocol. In OMAP4, USB PHY is connected via + OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via + OCP2SCP. + +endmenu diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile new file mode 100644 index 0000000..0ec50bc --- /dev/null +++ b/drivers/bus/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for the bus drivers. +# + +obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c new file mode 100644 index 0000000..8c3db3a --- /dev/null +++ b/drivers/bus/omap-ocp2scp.c @@ -0,0 +1,98 @@ +/* + * omap-ocp2scp.c - transform ocp interface protocol to scp protocol + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Author: Kishon Vijay Abraham I <kishon@ti.com> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/err.h> +#include <linux/pm_runtime.h> +#include <linux/of.h> +#include <linux/of_platform.h> + +static int ocp2scp_remove_devices(struct device *dev, void *c) +{ + struct platform_device *pdev = to_platform_device(dev); + + platform_device_unregister(pdev); + + return 0; +} + +static int __devinit omap_ocp2scp_probe(struct platform_device *pdev) +{ + int ret; + struct device_node *np = pdev->dev.of_node; + + if (np) { + ret = of_platform_populate(np, NULL, NULL, &pdev->dev); + if (ret) { + dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n"); + goto err0; + } + } + pm_runtime_enable(&pdev->dev); + + return 0; + +err0: + device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices); + + return ret; +} + +static int __devexit omap_ocp2scp_remove(struct platform_device *pdev) +{ + pm_runtime_disable(&pdev->dev); + device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices); + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id omap_ocp2scp_id_table[] = { + { .compatible = "ti,omap-ocp2scp" }, + {} +}; +MODULE_DEVICE_TABLE(of, omap_usb2_id_table); +#endif + +static struct platform_driver omap_ocp2scp_driver = { + .probe = omap_ocp2scp_probe, + .remove = __devexit_p(omap_ocp2scp_remove), + .driver = { + .name = "omap-ocp2scp", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(omap_ocp2scp_id_table), + }, +}; + +static int __init omap_ocp2scp_init(void) +{ + return platform_driver_register(&omap_ocp2scp_driver); +} +arch_initcall(omap_ocp2scp_init); + +static void __exit omap_ocp2scp_exit(void) +{ + platform_driver_unregister(&omap_ocp2scp_driver); +} +module_exit(omap_ocp2scp_exit); + +MODULE_ALIAS("platform: omap-ocp2scp"); +MODULE_AUTHOR("Texas Instruments Inc."); +MODULE_DESCRIPTION("OMAP OCP2SCP DRIVER"); +MODULE_LICENSE("GPLv2"); -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 1/2] drivers: bus: add a new driver for omap-ocp2scp 2012-07-16 14:13 ` [PATCH 1/2] drivers: bus: add a new driver for omap-ocp2scp Kishon Vijay Abraham I @ 2012-07-17 5:13 ` ABRAHAM, KISHON VIJAY 2012-07-17 8:00 ` Arnd Bergmann 0 siblings, 1 reply; 7+ messages in thread From: ABRAHAM, KISHON VIJAY @ 2012-07-17 5:13 UTC (permalink / raw) To: linux-arm-kernel +Arnd Bergmann On Mon, Jul 16, 2012 at 7:43 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote: > Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of > creating all the devices that is connected to OCP2SCP. In the case of OMAP4, > USB2PHY is connected to ocp2scp. > > This also includes device tree support for ocp2scp driver and > the documentation with device tree binding information is updated. > > Cc: Felipe Balbi <balbi@ti.com> > Cc: Arnd Bergmann <arnd@arndb.de> > Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> > --- > .../devicetree/bindings/bus/omap-ocp2scp.txt | 10 ++ > drivers/Kconfig | 2 + > drivers/Makefile | 2 + > drivers/bus/Kconfig | 15 +++ > drivers/bus/Makefile | 5 + > drivers/bus/omap-ocp2scp.c | 98 ++++++++++++++++++++ > 6 files changed, 132 insertions(+), 0 deletions(-) > create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt > create mode 100644 drivers/bus/Kconfig > create mode 100644 drivers/bus/Makefile > create mode 100644 drivers/bus/omap-ocp2scp.c > > diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt > new file mode 100644 > index 0000000..d2fe064 > --- /dev/null > +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt > @@ -0,0 +1,10 @@ > +* OMAP OCP2SCP - ocp interface to scp interface > + > +properties: > +- compatible : Should be "ti,omap-ocp2scp" > +- #address-cells, #size-cells : Must be present if the device has sub-nodes > +- ranges : the child address space are mapped 1:1 onto the parent address space > +- ti,hwmods : must be "ocp2scp_usb_phy" > + > +Sub-nodes: > +All the devices connected to ocp2scp are described using sub-node to ocp2scp > diff --git a/drivers/Kconfig b/drivers/Kconfig > index bfc9186..4fe1e4c 100644 > --- a/drivers/Kconfig > +++ b/drivers/Kconfig > @@ -2,6 +2,8 @@ menu "Device Drivers" > > source "drivers/base/Kconfig" > > +source "drivers/bus/Kconfig" > + > source "drivers/connector/Kconfig" > > source "drivers/mtd/Kconfig" > diff --git a/drivers/Makefile b/drivers/Makefile > index 2ba29ff..cac3819 100644 > --- a/drivers/Makefile > +++ b/drivers/Makefile > @@ -5,6 +5,8 @@ > # Rewritten to use lists instead of if-statements. > # > > +obj-y += bus/ > + > # GPIO must come after pinctrl as gpios may need to mux pins etc > obj-y += pinctrl/ > obj-y += gpio/ > diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig > new file mode 100644 > index 0000000..6270415 > --- /dev/null > +++ b/drivers/bus/Kconfig > @@ -0,0 +1,15 @@ > +# > +# Bus Devices > +# > + > +menu "Bus devices" > + > +config OMAP_OCP2SCP > + tristate "OMAP OCP2SCP DRIVER" > + help > + Driver to enable ocp2scp module which transforms ocp interface > + protocol to scp protocol. In OMAP4, USB PHY is connected via > + OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via > + OCP2SCP. > + > +endmenu > diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile > new file mode 100644 > index 0000000..0ec50bc > --- /dev/null > +++ b/drivers/bus/Makefile > @@ -0,0 +1,5 @@ > +# > +# Makefile for the bus drivers. > +# > + > +obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o > diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c > new file mode 100644 > index 0000000..8c3db3a > --- /dev/null > +++ b/drivers/bus/omap-ocp2scp.c > @@ -0,0 +1,98 @@ > +/* > + * omap-ocp2scp.c - transform ocp interface protocol to scp protocol > + * > + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * Author: Kishon Vijay Abraham I <kishon@ti.com> > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/err.h> > +#include <linux/pm_runtime.h> > +#include <linux/of.h> > +#include <linux/of_platform.h> > + > +static int ocp2scp_remove_devices(struct device *dev, void *c) > +{ > + struct platform_device *pdev = to_platform_device(dev); > + > + platform_device_unregister(pdev); > + > + return 0; > +} > + > +static int __devinit omap_ocp2scp_probe(struct platform_device *pdev) > +{ > + int ret; > + struct device_node *np = pdev->dev.of_node; > + > + if (np) { > + ret = of_platform_populate(np, NULL, NULL, &pdev->dev); > + if (ret) { > + dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n"); > + goto err0; > + } > + } > + pm_runtime_enable(&pdev->dev); > + > + return 0; > + > +err0: > + device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices); > + > + return ret; > +} > + > +static int __devexit omap_ocp2scp_remove(struct platform_device *pdev) > +{ > + pm_runtime_disable(&pdev->dev); > + device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices); > + > + return 0; > +} > + > +#ifdef CONFIG_OF > +static const struct of_device_id omap_ocp2scp_id_table[] = { > + { .compatible = "ti,omap-ocp2scp" }, > + {} > +}; > +MODULE_DEVICE_TABLE(of, omap_usb2_id_table); > +#endif > + > +static struct platform_driver omap_ocp2scp_driver = { > + .probe = omap_ocp2scp_probe, > + .remove = __devexit_p(omap_ocp2scp_remove), > + .driver = { > + .name = "omap-ocp2scp", > + .owner = THIS_MODULE, > + .of_match_table = of_match_ptr(omap_ocp2scp_id_table), > + }, > +}; > + > +static int __init omap_ocp2scp_init(void) > +{ > + return platform_driver_register(&omap_ocp2scp_driver); > +} > +arch_initcall(omap_ocp2scp_init); > + > +static void __exit omap_ocp2scp_exit(void) > +{ > + platform_driver_unregister(&omap_ocp2scp_driver); > +} > +module_exit(omap_ocp2scp_exit); > + > +MODULE_ALIAS("platform: omap-ocp2scp"); > +MODULE_AUTHOR("Texas Instruments Inc."); > +MODULE_DESCRIPTION("OMAP OCP2SCP DRIVER"); > +MODULE_LICENSE("GPLv2"); > -- > 1.7.5.4 > ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 1/2] drivers: bus: add a new driver for omap-ocp2scp 2012-07-17 5:13 ` ABRAHAM, KISHON VIJAY @ 2012-07-17 8:00 ` Arnd Bergmann 0 siblings, 0 replies; 7+ messages in thread From: Arnd Bergmann @ 2012-07-17 8:00 UTC (permalink / raw) To: linux-arm-kernel On Tuesday 17 July 2012, ABRAHAM, KISHON VIJAY wrote: > On Mon, Jul 16, 2012 at 7:43 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote: > > Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of > > creating all the devices that is connected to OCP2SCP. In the case of OMAP4, > > USB2PHY is connected to ocp2scp. > > > > This also includes device tree support for ocp2scp driver and > > the documentation with device tree binding information is updated. > > > > Cc: Felipe Balbi <balbi@ti.com> > > Cc: Arnd Bergmann <arnd@arndb.de> > > Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Now that we've found a place for the code to live, do we know which maintainer is going to pick it up? If nobody else volunteers, we can take it through the arm-soc tree. Arnd ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 2/2] arm/dts: omap4: Add ocp2scp data 2012-07-16 14:13 [PATCH 0/2] omap: add ocp2scp as a bus driver Kishon Vijay Abraham I 2012-07-16 14:13 ` [PATCH 1/2] drivers: bus: add a new driver for omap-ocp2scp Kishon Vijay Abraham I @ 2012-07-16 14:13 ` Kishon Vijay Abraham I 2012-07-17 12:36 ` Sergei Shtylyov 1 sibling, 1 reply; 7+ messages in thread From: Kishon Vijay Abraham I @ 2012-07-16 14:13 UTC (permalink / raw) To: linux-arm-kernel Add ocp2scp data node in omap4 device tree file. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- arch/arm/boot/dts/omap4.dtsi | 8 ++++++++ 1 files changed, 8 insertions(+), 0 deletions(-) diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 359c497..bda5df3 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -272,5 +272,13 @@ ti,hwmods = "mmc5"; ti,needs-special-reset; }; + + ocp2scp at 4a0ad000 { + compatible = "ti,omap-ocp2scp"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "ocp2scp_usb_phy"; + }; }; }; -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/2] arm/dts: omap4: Add ocp2scp data 2012-07-16 14:13 ` [PATCH 2/2] arm/dts: omap4: Add ocp2scp data Kishon Vijay Abraham I @ 2012-07-17 12:36 ` Sergei Shtylyov 2012-07-18 5:43 ` ABRAHAM, KISHON VIJAY 0 siblings, 1 reply; 7+ messages in thread From: Sergei Shtylyov @ 2012-07-17 12:36 UTC (permalink / raw) To: linux-arm-kernel Hello. On 16-07-2012 18:13, Kishon Vijay Abraham I wrote: > Add ocp2scp data node in omap4 device tree file. > Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> > --- > arch/arm/boot/dts/omap4.dtsi | 8 ++++++++ > 1 files changed, 8 insertions(+), 0 deletions(-) > diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi > index 359c497..bda5df3 100644 > --- a/arch/arm/boot/dts/omap4.dtsi > +++ b/arch/arm/boot/dts/omap4.dtsi > @@ -272,5 +272,13 @@ > ti,hwmods = "mmc5"; > ti,needs-special-reset; > }; > + > + ocp2scp at 4a0ad000 { "reg" property is absent, so why do you give the node name an address postfix? > + compatible = "ti,omap-ocp2scp"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + ti,hwmods = "ocp2scp_usb_phy"; > + }; WBR, Sergei ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 2/2] arm/dts: omap4: Add ocp2scp data 2012-07-17 12:36 ` Sergei Shtylyov @ 2012-07-18 5:43 ` ABRAHAM, KISHON VIJAY 0 siblings, 0 replies; 7+ messages in thread From: ABRAHAM, KISHON VIJAY @ 2012-07-18 5:43 UTC (permalink / raw) To: linux-arm-kernel Hi, On Tue, Jul 17, 2012 at 6:06 PM, Sergei Shtylyov <sshtylyov@mvista.com> wrote: > Hello. > > > On 16-07-2012 18:13, Kishon Vijay Abraham I wrote: > >> Add ocp2scp data node in omap4 device tree file. > > >> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> >> --- >> arch/arm/boot/dts/omap4.dtsi | 8 ++++++++ >> 1 files changed, 8 insertions(+), 0 deletions(-) > > >> diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi >> index 359c497..bda5df3 100644 >> --- a/arch/arm/boot/dts/omap4.dtsi >> +++ b/arch/arm/boot/dts/omap4.dtsi >> @@ -272,5 +272,13 @@ >> ti,hwmods = "mmc5"; >> ti,needs-special-reset; >> }; >> + >> + ocp2scp at 4a0ad000 { > > > "reg" property is absent, so why do you give the node name an address > postfix? When I was initially developing, I had "reg" property populated. Those info is now obtained from *ti,hwmods*. I'll resend the patch removing it. Thanks Kishon ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2012-07-18 5:43 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2012-07-16 14:13 [PATCH 0/2] omap: add ocp2scp as a bus driver Kishon Vijay Abraham I 2012-07-16 14:13 ` [PATCH 1/2] drivers: bus: add a new driver for omap-ocp2scp Kishon Vijay Abraham I 2012-07-17 5:13 ` ABRAHAM, KISHON VIJAY 2012-07-17 8:00 ` Arnd Bergmann 2012-07-16 14:13 ` [PATCH 2/2] arm/dts: omap4: Add ocp2scp data Kishon Vijay Abraham I 2012-07-17 12:36 ` Sergei Shtylyov 2012-07-18 5:43 ` ABRAHAM, KISHON VIJAY
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).