From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 15/16] ARM: Kirkwood: Describe iConnect LEDs in DT.
Date: Fri, 20 Jul 2012 19:35:50 +0200 [thread overview]
Message-ID: <1342805751-18048-16-git-send-email-andrew@lunn.ch> (raw)
In-Reply-To: <1342805751-18048-1-git-send-email-andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/kirkwood-iconnect.dts | 34 +++++++++++++++++++++++
arch/arm/mach-kirkwood/board-iconnect.c | 46 -------------------------------
2 files changed, 34 insertions(+), 46 deletions(-)
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts
index a7dd07b..b77b38f 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -31,4 +31,38 @@
status = "ok";
};
};
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led-level {
+ label = "led_level";
+ gpios = <&gpio1 9 0>;
+ linux,default-trigger = "default-on";
+ };
+ power-blue {
+ label = "power:blue";
+ gpios = <&gpio1 11 0>;
+ linux,default-trigger = "timer";
+ };
+ usb1 {
+ label = "usb1:blue";
+ gpios = <&gpio1 12 0>;
+ };
+ usb2 {
+ label = "usb2:blue";
+ gpios = <&gpio1 13 0>;
+ };
+ usb3 {
+ label = "usb3:blue";
+ gpios = <&gpio1 14 0>;
+ };
+ usb4 {
+ label = "usb4:blue";
+ gpios = <&gpio1 15 0>;
+ };
+ otb {
+ label = "otb:blue";
+ gpios = <&gpio1 16 0>;
+ };
+ };
};
diff --git a/arch/arm/mach-kirkwood/board-iconnect.c b/arch/arm/mach-kirkwood/board-iconnect.c
index df043aa..d7a9198 100644
--- a/arch/arm/mach-kirkwood/board-iconnect.c
+++ b/arch/arm/mach-kirkwood/board-iconnect.c
@@ -19,7 +19,6 @@
#include <linux/mtd/partitions.h>
#include <linux/mv643xx_eth.h>
#include <linux/gpio.h>
-#include <linux/leds.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <asm/mach/arch.h>
@@ -31,50 +30,6 @@ static struct mv643xx_eth_platform_data iconnect_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(11),
};
-static struct gpio_led iconnect_led_pins[] = {
- {
- .name = "led_level",
- .gpio = 41,
- .default_trigger = "default-on",
- }, {
- .name = "power:blue",
- .gpio = 42,
- .default_trigger = "timer",
- }, {
- .name = "power:red",
- .gpio = 43,
- }, {
- .name = "usb1:blue",
- .gpio = 44,
- }, {
- .name = "usb2:blue",
- .gpio = 45,
- }, {
- .name = "usb3:blue",
- .gpio = 46,
- }, {
- .name = "usb4:blue",
- .gpio = 47,
- }, {
- .name = "otb:blue",
- .gpio = 48,
- },
-};
-
-static struct gpio_led_platform_data iconnect_led_data = {
- .leds = iconnect_led_pins,
- .num_leds = ARRAY_SIZE(iconnect_led_pins),
- .gpio_blink_set = orion_gpio_led_blink_set,
-};
-
-static struct platform_device iconnect_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &iconnect_led_data,
- }
-};
-
static unsigned int iconnect_mpp_config[] __initdata = {
MPP12_GPIO,
MPP35_GPIO,
@@ -140,7 +95,6 @@ void __init iconnect_init(void)
kirkwood_ge00_init(&iconnect_ge00_data);
platform_device_register(&iconnect_button_device);
- platform_device_register(&iconnect_leds);
}
static int __init iconnect_pci_init(void)
--
1.7.10
next prev parent reply other threads:[~2012-07-20 17:35 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-07-20 17:35 [PATCH 00/16] Orion DT conversions and fixes Andrew Lunn
2012-07-20 17:35 ` [PATCH 1/16] ARM: Orion: DT support for IRQ and GPIO Controllers Andrew Lunn
2012-07-20 17:35 ` [PATCH 2/16] SPI: Refactor spi-orion to use SPI framework queue Andrew Lunn
2012-07-22 7:22 ` Linus Walleij
2012-07-22 9:53 ` Andrew Lunn
2012-07-22 19:07 ` Mark Brown
2012-07-22 19:32 ` Andrew Lunn
2012-07-22 22:42 ` Mark Brown
2012-07-23 7:27 ` Andrew Lunn
2012-07-23 9:37 ` Mark Brown
2012-07-23 10:08 ` [PATCH] spi-orion: add device tree binding Andrew Lunn
2012-07-23 10:43 ` Mark Brown
2012-07-23 10:59 ` Andrew Lunn
2012-07-23 11:12 ` Mark Brown
2012-07-23 17:43 ` Arnd Bergmann
2012-07-23 10:44 ` Mark Brown
2012-07-23 10:50 ` Andrew Lunn
2012-07-23 10:16 ` [PATCH 2/16] SPI: Refactor spi-orion to use SPI framework queue Andrew Lunn
2012-07-23 10:23 ` Mark Brown
2012-07-23 10:49 ` Andrew Lunn
2012-07-23 11:11 ` Mark Brown
2012-07-23 10:53 ` Sergei Shtylyov
2012-07-23 11:02 ` Andrew Lunn
2012-07-20 17:35 ` [PATCH 3/16] ARM: Kirkwood: Ensure runit clock always ticks Andrew Lunn
2012-07-20 17:35 ` [PATCH 4/16] ARM: Orion: Add arch support needed for I2C via DT Andrew Lunn
2012-07-20 17:35 ` [PATCH 5/16] Kirkwood: Add basic device tree support for QNAP TS219 Andrew Lunn
2012-07-20 17:35 ` [PATCH 6/16] ARM: Orion: DTify the watchdog timer Andrew Lunn
2012-07-20 17:35 ` [PATCH 7/16] ATA: sata_mv: Add device tree support Andrew Lunn
2012-07-20 17:35 ` [PATCH 8/16] ARM: Kirkwood: Use DT to configure SATA device Andrew Lunn
2012-07-20 17:35 ` [PATCH 9/16] ARM: Kirkwood: Describe DNS325 temperature sensor in DT Andrew Lunn
2012-07-20 17:35 ` [PATCH 10/16] ARM: Kirkwood: Describe IB62x0 gpio-keys " Andrew Lunn
2012-07-20 17:35 ` [PATCH 11/16] ARM: Kirkwood: Describe iConnects temperature sensor " Andrew Lunn
2012-07-20 17:35 ` [PATCH 12/16] ARM: Kirkwood: Describe Dreamplug LEDs " Andrew Lunn
2012-07-20 17:35 ` [PATCH 13/16] ARM: Kirkwood: Describe GoFlex Net LEDs and SATA " Andrew Lunn
2012-07-20 17:35 ` [PATCH 14/16] ARM: Kirkwood: Describe ib62x0 LEDs " Andrew Lunn
2012-07-20 17:35 ` Andrew Lunn [this message]
2012-07-30 21:35 ` [PATCH 15/16] ARM: Kirkwood: Describe iConnect " Adam Baker
2012-07-31 6:36 ` Andrew Lunn
2012-07-31 7:08 ` Arnaud Patard (Rtp)
2012-07-31 7:20 ` Andrew Lunn
2012-07-31 8:59 ` Arnaud Patard (Rtp)
2012-07-20 17:35 ` [PATCH 16/16] ARM: Kirkwood: Replace mrvl with marvell Andrew Lunn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1342805751-18048-16-git-send-email-andrew@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).