From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [RFC 10/11] ARM: Kirkwood: Convert lsxl boards to pinctrl.
Date: Sat, 20 Oct 2012 15:11:40 -0000 [thread overview]
Message-ID: <1350745663-5277-11-git-send-email-andrew@lunn.ch> (raw)
In-Reply-To: <1350745663-5277-1-git-send-email-andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/kirkwood-lsxl.dtsi | 67 ++++++++++++++++++++++++++++++++++
arch/arm/mach-kirkwood/board-lsxl.c | 19 ----------
2 files changed, 67 insertions(+), 19 deletions(-)
diff --git a/arch/arm/boot/dts/kirkwood-lsxl.dtsi b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
index 8ac51c0..9535559 100644
--- a/arch/arm/boot/dts/kirkwood-lsxl.dtsi
+++ b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
@@ -6,6 +6,73 @@
};
ocp at f1000000 {
+ pinctrl: pinctrl at 10000 {
+ compatible = "marvell,88f6281-pinctrl";
+ reg = <0x10000 0x20>;
+
+ pinctrl-0 = < &pmx_power_hdd &pmx_usb_vbus
+ &pmx_fan_low &pmx_fan_high
+ &pmx_led_function_red &pmx_led_alarm
+ &pmx_led_info &pmx_led_power
+ &pmx_fan_lock &pmx_button_function
+ &pmx_power_switch &pmx_power_auto_switch
+ &pmx_led_function_blue >;
+ pinctrl-names = "default";
+
+ pmx_power_hdd: pmx-power-hdd {
+ marvell,pins = "mpp10";
+ marvell,function = "gpio";
+ };
+ pmx_usb_vbus: pmx-usb-vbus {
+ marvell,pins = "mpp11";
+ marvell,function = "gpio";
+ };
+ pmx_fan_high: pmx-fan-high {
+ marvell,pins = "mpp18";
+ marvell,function = "gpo";
+ };
+ pmx_fan_low: pmx-fan-low {
+ marvell,pins = "mpp19";
+ marvell,function = "gpo";
+ };
+ pmx_led_function_blue: pmx-led-function-blue {
+ marvell,pins = "mpp36";
+ marvell,function = "gpio";
+ };
+ pmx_led_alarm: pmx-led-alarm {
+ marvell,pins = "mpp37";
+ marvell,function = "gpio";
+ };
+ pmx_led_info: pmx-led-info {
+ marvell,pins = "mpp38";
+ marvell,function = "gpio";
+ };
+ pmx_led_power: pmx-led-power {
+ marvell,pins = "mpp39";
+ marvell,function = "gpio";
+ };
+ pmx_fan_lock: pmx-fan-lock {
+ marvell,pins = "mpp40";
+ marvell,function = "gpo";
+ };
+ pmx_button_function: pmx-button-function {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ pmx_power_switch: pmx-power-switch {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+ pmx_power_auto_switch: pmx-power-auto-switch {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ pmx_led_function_red: pmx-led-function_red {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+
+ };
sata at 80000 {
status = "okay";
nr-ports = <1>;
diff --git a/arch/arm/mach-kirkwood/board-lsxl.c b/arch/arm/mach-kirkwood/board-lsxl.c
index 83d8975..868bdb0 100644
--- a/arch/arm/mach-kirkwood/board-lsxl.c
+++ b/arch/arm/mach-kirkwood/board-lsxl.c
@@ -26,7 +26,6 @@
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
#include "common.h"
-#include "mpp.h"
static struct mv643xx_eth_platform_data lsxl_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(0),
@@ -36,23 +35,6 @@ static struct mv643xx_eth_platform_data lsxl_ge01_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(8),
};
-static unsigned int lsxl_mpp_config[] __initdata = {
- MPP10_GPO, /* HDD Power Enable */
- MPP11_GPIO, /* USB Vbus Enable */
- MPP18_GPO, /* FAN High Enable# */
- MPP19_GPO, /* FAN Low Enable# */
- MPP36_GPIO, /* Function Blue LED */
- MPP37_GPIO, /* Alarm LED */
- MPP38_GPIO, /* Info LED */
- MPP39_GPIO, /* Power LED */
- MPP40_GPIO, /* Fan Lock */
- MPP41_GPIO, /* Function Button */
- MPP42_GPIO, /* Power Switch */
- MPP43_GPIO, /* Power Auto Switch */
- MPP48_GPIO, /* Function Red LED */
- 0
-};
-
#define LSXL_GPIO_FAN_HIGH 18
#define LSXL_GPIO_FAN_LOW 19
#define LSXL_GPIO_FAN_LOCK 40
@@ -119,7 +101,6 @@ void __init lsxl_init(void)
/*
* Basic setup. Needs to be called early.
*/
- kirkwood_mpp_conf(lsxl_mpp_config);
/* usb and sata power on */
gpio_set_value(LSXL_GPIO_USB_POWER, 1);
--
1.7.10.4
next prev parent reply other threads:[~2012-10-20 15:11 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-20 15:07 [RFC 00/11] Convert Kirkwood to pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 07/11] ARM: Kirkwood: Convert dreamplug " Andrew Lunn
2012-10-20 15:11 ` [RFC 06/11] ARM: Kirkwood: Convert dockstar " Andrew Lunn
2012-10-20 15:11 ` [RFC 05/11] ARM: Kirkwood: Convert dnskw " Andrew Lunn
2012-10-20 15:11 ` [RFC 02/11] ARM: Kirkwood: Allow use of MVEBU GPIO driver Andrew Lunn
2012-10-20 15:11 ` [RFC 01/11] ARM: Kirkwood: Allow use of pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 03/11] ARM: Kirkwood: Convert TS219 to pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 04/11] ARM: Kirkwood: Convert iConnect " Andrew Lunn
2012-10-20 15:11 ` [RFC 08/11] ARM: Kirkwood: Convert GoFlex Net " Andrew Lunn
2012-10-20 15:11 ` [RFC 09/11] ARM: Kirkwood: Convert ib62x0 " Andrew Lunn
2012-10-20 15:11 ` Andrew Lunn [this message]
2012-10-20 15:11 ` [RFC 11/11] ARM: Kirkwood: Convert IX2-200 " Andrew Lunn
[not found] ` <20121021115716.GA22437@schnuecks.de>
2012-10-21 17:57 ` [RFC 00/11] Convert Kirkwood " Andrew Lunn
2012-10-21 19:09 ` Thomas Petazzoni
2012-10-21 19:16 ` Andrew Lunn
2012-10-21 21:11 ` Sebastian Hesselbarth
2012-10-22 4:54 ` Andrew Lunn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1350745663-5277-11-git-send-email-andrew@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).