From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [RFC 11/11] ARM: Kirkwood: Convert IX2-200 to pinctrl.
Date: Sat, 20 Oct 2012 15:11:42 -0000 [thread overview]
Message-ID: <1350745663-5277-12-git-send-email-andrew@lunn.ch> (raw)
In-Reply-To: <1350745663-5277-1-git-send-email-andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts | 90 +++++++++++++++++++++++++
arch/arm/mach-kirkwood/board-iomega_ix2_200.c | 24 -------
2 files changed, 90 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
index 865aeec..d8fa8e8 100644
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
@@ -16,6 +16,96 @@
};
ocp at f1000000 {
+ pinctrl: pinctrl at 10000 {
+ compatible = "marvell,88f6281-pinctrl";
+ reg = <0x10000 0x20>;
+
+ pinctrl-0 = < &pmx_button_reset &pmx_button_power
+ &pmx_led_backup &pmx_led_power
+ &pmx_button_otb &pmx_led_rebuild
+ &pmx_led_health
+ &pmx_led_sata_brt_ctrl_1
+ &pmx_led_sata_brt_ctrl_2
+ &pmx_led_backup_brt_ctrl_1
+ &pmx_led_backup_brt_ctrl_2
+ &pmx_led_power_brt_ctrl_1
+ &pmx_led_power_brt_ctrl_2
+ &pmx_led_health_brt_ctrl_1
+ &pmx_led_health_brt_ctrl_2
+ &pmx_led_rebuild_brt_ctrl_1
+ &pmx_led_rebuild_brt_ctrl_2 >;
+ pinctrl-names = "default";
+
+ pmx_button_reset: pmx-button-reset {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+ pmx_button_power: pmx-button-power {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+ pmx_led_backup: pmx-led-backup {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+ pmx_led_power: pmx-led-power {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+ pmx_button_otb: pmx-button-otb {
+ marvell,pins = "mpp35";
+ marvell,function = "gpio";
+ };
+ pmx_led_rebuild: pmx-led-rebuild {
+ marvell,pins = "mpp36";
+ marvell,function = "gpio";
+ };
+ pmx_led_health: pmx-led_health {
+ marvell,pins = "mpp37";
+ marvell,function = "gpio";
+ };
+ pmx_led_sata_brt_ctrl_1: pmx-led-sata-brt-ctrl-1 {
+ marvell,pins = "mpp38";
+ marvell,function = "gpio";
+ };
+ pmx_led_sata_brt_ctrl_2: pmx-led-sata-brt-ctrl-2 {
+ marvell,pins = "mpp39";
+ marvell,function = "gpio";
+ };
+ pmx_led_backup_brt_ctrl_1: pmx-led-backup-brt-ctrl-1 {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_led_backup_brt_ctrl_2: pmx-led-backup-brt-ctrl-2 {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ pmx_led_power_brt_ctrl_1: pmx-led-power-brt-ctrl-1 {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+ pmx_led_power_brt_ctrl_2: pmx-led-power-brt-ctrl-2 {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ pmx_led_health_brt_ctrl_1: pmx-led-health-brt-ctrl-1 {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+ pmx_led_health_brt_ctrl_2: pmx-led-health-brt-ctrl-2 {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+ pmx_led_rebuild_brt_ctrl_1: pmx-led-rebuild-brt-ctrl-1 {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+ pmx_led_rebuild_brt_ctrl_2: pmx-led-rebuild-brt-ctrl-2 {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ };
i2c at 11000 {
status = "okay";
diff --git a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
index 158fb97..c144712 100644
--- a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
+++ b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
@@ -15,7 +15,6 @@
#include <linux/ethtool.h>
#include <mach/kirkwood.h>
#include "common.h"
-#include "mpp.h"
static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_NONE,
@@ -23,34 +22,11 @@ static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = {
.duplex = DUPLEX_FULL,
};
-static unsigned int iomega_ix2_200_mpp_config[] __initdata = {
- MPP12_GPIO, /* Reset Button */
- MPP14_GPIO, /* Power Button */
- MPP15_GPIO, /* Backup LED (blue) */
- MPP16_GPIO, /* Power LED (white) */
- MPP35_GPIO, /* OTB Button */
- MPP36_GPIO, /* Rebuild LED (white) */
- MPP37_GPIO, /* Health LED (red) */
- MPP38_GPIO, /* SATA LED brightness control 1 */
- MPP39_GPIO, /* SATA LED brightness control 2 */
- MPP40_GPIO, /* Backup LED brightness control 1 */
- MPP41_GPIO, /* Backup LED brightness control 2 */
- MPP42_GPIO, /* Power LED brightness control 1 */
- MPP43_GPIO, /* Power LED brightness control 2 */
- MPP44_GPIO, /* Health LED brightness control 1 */
- MPP45_GPIO, /* Health LED brightness control 2 */
- MPP46_GPIO, /* Rebuild LED brightness control 1 */
- MPP47_GPIO, /* Rebuild LED brightness control 2 */
- 0
-};
-
void __init iomega_ix2_200_init(void)
{
/*
* Basic setup. Needs to be called early.
*/
- kirkwood_mpp_conf(iomega_ix2_200_mpp_config);
-
kirkwood_ehci_init();
kirkwood_ge01_init(&iomega_ix2_200_ge00_data);
--
1.7.10.4
next prev parent reply other threads:[~2012-10-20 15:11 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-20 15:07 [RFC 00/11] Convert Kirkwood to pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 07/11] ARM: Kirkwood: Convert dreamplug " Andrew Lunn
2012-10-20 15:11 ` [RFC 06/11] ARM: Kirkwood: Convert dockstar " Andrew Lunn
2012-10-20 15:11 ` [RFC 05/11] ARM: Kirkwood: Convert dnskw " Andrew Lunn
2012-10-20 15:11 ` [RFC 02/11] ARM: Kirkwood: Allow use of MVEBU GPIO driver Andrew Lunn
2012-10-20 15:11 ` [RFC 01/11] ARM: Kirkwood: Allow use of pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 03/11] ARM: Kirkwood: Convert TS219 to pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 04/11] ARM: Kirkwood: Convert iConnect " Andrew Lunn
2012-10-20 15:11 ` [RFC 08/11] ARM: Kirkwood: Convert GoFlex Net " Andrew Lunn
2012-10-20 15:11 ` [RFC 09/11] ARM: Kirkwood: Convert ib62x0 " Andrew Lunn
2012-10-20 15:11 ` [RFC 10/11] ARM: Kirkwood: Convert lsxl boards " Andrew Lunn
2012-10-20 15:11 ` Andrew Lunn [this message]
[not found] ` <20121021115716.GA22437@schnuecks.de>
2012-10-21 17:57 ` [RFC 00/11] Convert Kirkwood " Andrew Lunn
2012-10-21 19:09 ` Thomas Petazzoni
2012-10-21 19:16 ` Andrew Lunn
2012-10-21 21:11 ` Sebastian Hesselbarth
2012-10-22 4:54 ` Andrew Lunn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1350745663-5277-12-git-send-email-andrew@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).