From: robherring2@gmail.com (Rob Herring)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 5/6] ARM: highbank: abstract out SCU usage
Date: Fri, 26 Oct 2012 13:43:07 -0500 [thread overview]
Message-ID: <1351276988-28382-6-git-send-email-robherring2@gmail.com> (raw)
In-Reply-To: <1351276988-28382-1-git-send-email-robherring2@gmail.com>
From: Rob Herring <rob.herring@calxeda.com>
In preparation for A15 support on ECX-2000, the direct calls to SCU
registers must be conditional. The SCU power mode register is replaced by
a custom register on ECX-2000.
Rather than read the number of cores from the SCU, just hardcode it to 4.
This removes one use of SCU and removes the need for the SCU to be
statically mapped. The cpu initialization will ultimately come from DT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
---
arch/arm/mach-highbank/highbank.c | 21 +++++----------------
arch/arm/mach-highbank/hotplug.c | 6 ++----
arch/arm/mach-highbank/platsmp.c | 7 +++----
arch/arm/mach-highbank/pm.c | 3 ---
arch/arm/mach-highbank/sysregs.h | 19 +++++++++++++++++++
arch/arm/mach-highbank/system.c | 2 --
6 files changed, 29 insertions(+), 29 deletions(-)
diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c
index 40e36a5..3da921a 100644
--- a/arch/arm/mach-highbank/highbank.c
+++ b/arch/arm/mach-highbank/highbank.c
@@ -28,30 +28,19 @@
#include <asm/cacheflush.h>
#include <asm/smp_plat.h>
-#include <asm/smp_scu.h>
#include <asm/smp_twd.h>
#include <asm/hardware/arm_timer.h>
#include <asm/hardware/timer-sp.h>
#include <asm/hardware/gic.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include "core.h"
#include "sysregs.h"
void __iomem *sregs_base;
-
-#define HB_SCU_VIRT_BASE 0xfee00000
-void __iomem *scu_base_addr = ((void __iomem *)(HB_SCU_VIRT_BASE));
-
-static struct map_desc scu_io_desc __initdata = {
- .virtual = HB_SCU_VIRT_BASE,
- .pfn = 0, /* run-time */
- .length = SZ_4K,
- .type = MT_DEVICE,
-};
+void __iomem *scu_base_addr;
static void __init highbank_scu_map_io(void)
{
@@ -60,13 +49,11 @@ static void __init highbank_scu_map_io(void)
/* Get SCU base */
asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (base));
- scu_io_desc.pfn = __phys_to_pfn(base);
- iotable_init(&scu_io_desc, 1);
+ scu_base_addr = ioremap(base, SZ_4K);
}
static void __init highbank_map_io(void)
{
- highbank_scu_map_io();
highbank_lluart_map_io();
}
@@ -99,6 +86,9 @@ static void __init highbank_init_irq(void)
{
of_irq_init(irq_match);
+ if (of_find_compatible_node(NULL, NULL, "arm,cortex-a9"))
+ highbank_scu_map_io();
+
#ifdef CONFIG_CACHE_L2X0
/* Enable PL310 L2 Cache controller */
highbank_smc1(0x102, 0x1);
@@ -145,7 +135,6 @@ static struct sys_timer highbank_timer = {
static void highbank_power_off(void)
{
hignbank_set_pwr_shutdown();
- scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
while (1)
cpu_do_idle();
diff --git a/arch/arm/mach-highbank/hotplug.c b/arch/arm/mach-highbank/hotplug.c
index 2c1b8c3..7b60fac 100644
--- a/arch/arm/mach-highbank/hotplug.c
+++ b/arch/arm/mach-highbank/hotplug.c
@@ -14,13 +14,11 @@
* this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/smp.h>
-#include <asm/smp_scu.h>
#include <asm/cacheflush.h>
#include "core.h"
+#include "sysregs.h"
extern void secondary_startup(void);
@@ -33,7 +31,7 @@ void __ref highbank_cpu_die(unsigned int cpu)
flush_cache_all();
highbank_set_cpu_jump(cpu, secondary_startup);
- scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+ highbank_set_core_pwr();
cpu_do_idle();
diff --git a/arch/arm/mach-highbank/platsmp.c b/arch/arm/mach-highbank/platsmp.c
index fa9560e..1129957 100644
--- a/arch/arm/mach-highbank/platsmp.c
+++ b/arch/arm/mach-highbank/platsmp.c
@@ -42,9 +42,7 @@ static int __cpuinit highbank_boot_secondary(unsigned int cpu, struct task_struc
*/
static void __init highbank_smp_init_cpus(void)
{
- unsigned int i, ncores;
-
- ncores = scu_get_core_count(scu_base_addr);
+ unsigned int i, ncores = 4;
/* sanity check */
if (ncores > NR_CPUS) {
@@ -65,7 +63,8 @@ static void __init highbank_smp_prepare_cpus(unsigned int max_cpus)
{
int i;
- scu_enable(scu_base_addr);
+ if (scu_base_addr)
+ scu_enable(scu_base_addr);
/*
* Write the address of secondary startup into the jump table
diff --git a/arch/arm/mach-highbank/pm.c b/arch/arm/mach-highbank/pm.c
index de866f2..74aa135 100644
--- a/arch/arm/mach-highbank/pm.c
+++ b/arch/arm/mach-highbank/pm.c
@@ -19,7 +19,6 @@
#include <linux/suspend.h>
#include <asm/proc-fns.h>
-#include <asm/smp_scu.h>
#include <asm/suspend.h>
#include "core.h"
@@ -35,8 +34,6 @@ static int highbank_pm_enter(suspend_state_t state)
{
hignbank_set_pwr_suspend();
highbank_set_cpu_jump(0, cpu_resume);
-
- scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
cpu_suspend(0, highbank_suspend_finish);
return 0;
diff --git a/arch/arm/mach-highbank/sysregs.h b/arch/arm/mach-highbank/sysregs.h
index 0e91338..e13e8ea 100644
--- a/arch/arm/mach-highbank/sysregs.h
+++ b/arch/arm/mach-highbank/sysregs.h
@@ -17,6 +17,10 @@
#define _MACH_HIGHBANK__SYSREGS_H_
#include <linux/io.h>
+#include <linux/smp.h>
+#include <asm/smp_plat.h>
+#include <asm/smp_scu.h>
+#include "core.h"
extern void __iomem *sregs_base;
@@ -29,24 +33,39 @@ extern void __iomem *sregs_base;
#define HB_PWR_HARD_RESET 2
#define HB_PWR_SHUTDOWN 3
+#define SREG_CPU_PWR_CTRL(c) (0x200 + ((c) * 4))
+
+static inline void highbank_set_core_pwr(void)
+{
+ int cpu = cpu_logical_map(smp_processor_id());
+ if (scu_base_addr)
+ scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+ else
+ writel_relaxed(1, sregs_base + SREG_CPU_PWR_CTRL(cpu));
+}
+
static inline void hignbank_set_pwr_suspend(void)
{
writel(HB_PWR_SUSPEND, sregs_base + HB_SREG_A9_PWR_REQ);
+ highbank_set_core_pwr();
}
static inline void hignbank_set_pwr_shutdown(void)
{
writel(HB_PWR_SHUTDOWN, sregs_base + HB_SREG_A9_PWR_REQ);
+ highbank_set_core_pwr();
}
static inline void hignbank_set_pwr_soft_reset(void)
{
writel(HB_PWR_SOFT_RESET, sregs_base + HB_SREG_A9_PWR_REQ);
+ highbank_set_core_pwr();
}
static inline void hignbank_set_pwr_hard_reset(void)
{
writel(HB_PWR_HARD_RESET, sregs_base + HB_SREG_A9_PWR_REQ);
+ highbank_set_core_pwr();
}
#endif
diff --git a/arch/arm/mach-highbank/system.c b/arch/arm/mach-highbank/system.c
index 82c2723..194a5bb 100644
--- a/arch/arm/mach-highbank/system.c
+++ b/arch/arm/mach-highbank/system.c
@@ -14,7 +14,6 @@
* this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/io.h>
-#include <asm/smp_scu.h>
#include <asm/proc-fns.h>
#include "core.h"
@@ -27,7 +26,6 @@ void highbank_restart(char mode, const char *cmd)
else
hignbank_set_pwr_soft_reset();
- scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
cpu_do_idle();
}
--
1.7.10.4
next prev parent reply other threads:[~2012-10-26 18:43 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-26 18:43 [PATCH 0/6] Initial Calxeda ECX-2000 support Rob Herring
2012-10-26 18:43 ` [PATCH 1/6] ARM: highbank: disable unused sdhci and gpio in dts Rob Herring
2012-10-26 18:43 ` [PATCH 2/6] ARM: highbank: enable coherent DMA for xgmac " Rob Herring
2012-10-26 18:43 ` [PATCH 3/6] ARM: dts: Add Calxeda ECX-2000 support Rob Herring
2012-10-26 18:43 ` [PATCH 4/6] ARM: smp_twd: don't warn on no DT node Rob Herring
2012-10-26 18:43 ` Rob Herring [this message]
2012-10-26 18:43 ` [PATCH 6/6] ARM: highbank: Add initial ECX-2000 support Rob Herring
2012-10-26 19:32 ` [PATCH 0/6] Initial Calxeda " Arnd Bergmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1351276988-28382-6-git-send-email-robherring2@gmail.com \
--to=robherring2@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).