[PATCH 0/6] Initial Calxeda ECX-2000 support

[PATCH 0/6] Initial Calxeda ECX-2000 support

[Rob Herring]

From: Rob Herring <rob.herring@calxeda.com>

This series adds initial support for Calxeda A15 based ECX-2000 SOC. Most
of the changes are shuffling of dts files to share common parts between
highbank (ECX-1000) and ECX-2000 and abstracting out or removing SCU
accesses as the A15 has no SCU registers.

Although the highbank name really refers to 1st gen SOC, the highbank
name in the kernel is now referring to both SOCs.

Rob

Rob Herring (6):
  ARM: highbank: disable unused sdhci and gpio in dts
  ARM: highbank: enable coherent DMA for xgmac in dts
  ARM: dts: Add Calxeda ECX-2000 support
  ARM: smp_twd: don't warn on no DT node
  ARM: highbank: abstract out SCU usage
  ARM: highbank: Add initial ECX-2000 support

 Documentation/devicetree/bindings/arm/calxeda.txt |   13 +-
 arch/arm/boot/dts/Makefile                        |    3 +-
 arch/arm/boot/dts/ecx-2000.dts                    |  104 +++++++++
 arch/arm/boot/dts/ecx-common.dtsi                 |  237 +++++++++++++++++++++
 arch/arm/boot/dts/highbank.dts                    |  212 +-----------------
 arch/arm/kernel/smp_twd.c                         |    6 +-
 arch/arm/mach-highbank/Kconfig                    |    2 +-
 arch/arm/mach-highbank/highbank.c                 |   27 +--
 arch/arm/mach-highbank/hotplug.c                  |    6 +-
 arch/arm/mach-highbank/platsmp.c                  |    7 +-
 arch/arm/mach-highbank/pm.c                       |    3 -
 arch/arm/mach-highbank/sysregs.h                  |   19 ++
 arch/arm/mach-highbank/system.c                   |    2 -
 13 files changed, 394 insertions(+), 247 deletions(-)
 create mode 100644 arch/arm/boot/dts/ecx-2000.dts
 create mode 100644 arch/arm/boot/dts/ecx-common.dtsi

-- 
1.7.10.4

[PATCH 1/6] ARM: highbank: disable unused sdhci and gpio in dts

[Rob Herring]

From: Rob Herring <rob.herring@calxeda.com>

These peripherals are not enabled in current systems, so turn them off.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
---
 arch/arm/boot/dts/highbank.dts |    5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/highbank.dts b/arch/arm/boot/dts/highbank.dts
index 0c6fc34..28d5872 100644
--- a/arch/arm/boot/dts/highbank.dts
+++ b/arch/arm/boot/dts/highbank.dts
@@ -132,6 +132,7 @@
 			reg = <0xffe0e000 0x1000>;
 			interrupts = <0 90 4>;
 			clocks = <&eclk>;
+			status = "disabled";
 		};
 
 		memory-controller at fff00000 {
@@ -156,6 +157,7 @@
 			interrupts = <0 14 4>;
 			clocks = <&pclk>;
 			clock-names = "apb_pclk";
+			status = "disabled";
 		};
 
 		gpiof: gpio at fff31000 {
@@ -166,6 +168,7 @@
 			interrupts = <0 15 4>;
 			clocks = <&pclk>;
 			clock-names = "apb_pclk";
+			status = "disabled";
 		};
 
 		gpiog: gpio at fff32000 {
@@ -176,6 +179,7 @@
 			interrupts = <0 16 4>;
 			clocks = <&pclk>;
 			clock-names = "apb_pclk";
+			status = "disabled";
 		};
 
 		gpioh: gpio at fff33000 {
@@ -186,6 +190,7 @@
 			interrupts = <0 17 4>;
 			clocks = <&pclk>;
 			clock-names = "apb_pclk";
+			status = "disabled";
 		};
 
 		timer {
-- 
1.7.10.4

[PATCH 2/6] ARM: highbank: enable coherent DMA for xgmac in dts

[Rob Herring]

From: Rob Herring <rob.herring@calxeda.com>

Enable the xgmac to use the coherent DMA path in highbank.dts

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
---
 arch/arm/boot/dts/highbank.dts |    2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/highbank.dts b/arch/arm/boot/dts/highbank.dts
index 28d5872..e39a79a 100644
--- a/arch/arm/boot/dts/highbank.dts
+++ b/arch/arm/boot/dts/highbank.dts
@@ -308,12 +308,14 @@
 			compatible = "calxeda,hb-xgmac";
 			reg = <0xfff50000 0x1000>;
 			interrupts = <0 77 4  0 78 4  0 79 4>;
+			dma-coherent;
 		};
 
 		ethernet at fff51000 {
 			compatible = "calxeda,hb-xgmac";
 			reg = <0xfff51000 0x1000>;
 			interrupts = <0 80 4  0 81 4  0 82 4>;
+			dma-coherent;
 		};
 
 		combophy0: combo-phy at fff58000 {
-- 
1.7.10.4

[PATCH 3/6] ARM: dts: Add Calxeda ECX-2000 support

[Rob Herring]

From: Rob Herring <rob.herring@calxeda.com>

Separate out common dts pieces from highbank dts and add support for
Calxeda ECX-2000 (Midway) SOC.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
---
 Documentation/devicetree/bindings/arm/calxeda.txt |   13 +-
 arch/arm/boot/dts/Makefile                        |    3 +-
 arch/arm/boot/dts/ecx-2000.dts                    |  104 +++++++++
 arch/arm/boot/dts/ecx-common.dtsi                 |  237 +++++++++++++++++++++
 arch/arm/boot/dts/highbank.dts                    |  219 +------------------
 5 files changed, 356 insertions(+), 220 deletions(-)
 create mode 100644 arch/arm/boot/dts/ecx-2000.dts
 create mode 100644 arch/arm/boot/dts/ecx-common.dtsi

diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt
index 4755caa..25fcf96 100644
--- a/Documentation/devicetree/bindings/arm/calxeda.txt
+++ b/Documentation/devicetree/bindings/arm/calxeda.txt
@@ -1,8 +1,15 @@
-Calxeda Highbank Platforms Device Tree Bindings
+Calxeda Platforms Device Tree Bindings
 -----------------------------------------------
 
-Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following
-properties.
+Boards with Calxeda Cortex-A9 based ECX-1000 (Highbank) SOC shall have the
+following properties.
 
 Required root node properties:
     - compatible = "calxeda,highbank";
+
+
+Boards with Calxeda Cortex-A15 based ECX-2000 SOC shall have the following
+properties.
+
+Required root node properties:
+    - compatible = "calxeda,ecx-2000";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f37cf9f..5cc9566 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -24,7 +24,8 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
 	exynos4210-trats.dtb \
 	exynos5250-smdk5250.dtb
-dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb
+dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \
+	ecx-2000.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
 	integratorcp.dtb
 dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
diff --git a/arch/arm/boot/dts/ecx-2000.dts b/arch/arm/boot/dts/ecx-2000.dts
new file mode 100644
index 0000000..46477ac
--- /dev/null
+++ b/arch/arm/boot/dts/ecx-2000.dts
@@ -0,0 +1,104 @@
+/*
+ * Copyright 2011-2012 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/dts-v1/;
+
+/* First 4KB has pen for secondary cores. */
+/memreserve/ 0x00000000 0x0001000;
+
+/ {
+	model = "Calxeda ECX-2000";
+	compatible = "calxeda,ecx-2000";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	clock-ranges;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+			clocks = <&a9pll>;
+			clock-names = "cpu";
+		};
+
+		cpu at 1 {
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+			clocks = <&a9pll>;
+			clock-names = "cpu";
+		};
+
+		cpu at 2 {
+			compatible = "arm,cortex-a15";
+			reg = <2>;
+			clocks = <&a9pll>;
+			clock-names = "cpu";
+		};
+
+		cpu at 3 {
+			compatible = "arm,cortex-a15";
+			reg = <3>;
+			clocks = <&a9pll>;
+			clock-names = "cpu";
+		};
+	};
+
+	memory at 0 {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0xff800000>;
+	};
+
+	memory at 200000000 {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x00000002 0x00000000 0x00000003 0x00000000>;
+	};
+
+	soc {
+		ranges = <0x00000000 0x00000000 0x00000000 0xffffffff>;
+
+		timer {
+			compatible = "arm,cortex-a15-timer", "arm,armv7-timer"; 			interrupts = <1 13 0xf08>,
+				<1 14 0xf08>,
+				<1 11 0xf08>,
+				<1 10 0xf08>;
+		};
+
+		intc: interrupt-controller at fff11000 {
+			compatible = "arm,cortex-a15-gic";
+			#interrupt-cells = <3>;
+			#size-cells = <0>;
+			#address-cells = <1>;
+			interrupt-controller;
+			interrupts = <1 9 0xf04>;
+			reg = <0xfff11000 0x1000>,
+			      <0xfff12000 0x1000>,
+			      <0xfff14000 0x2000>,
+			      <0xfff16000 0x2000>;
+		};
+
+		pmu {
+			compatible = "arm,cortex-a9-pmu";
+			interrupts = <0 76 4  0 75 4  0 74 4  0 73 4>;
+		};
+	};
+};
+
+/include/ "ecx-common.dtsi"
diff --git a/arch/arm/boot/dts/ecx-common.dtsi b/arch/arm/boot/dts/ecx-common.dtsi
new file mode 100644
index 0000000..d61b535
--- /dev/null
+++ b/arch/arm/boot/dts/ecx-common.dtsi
@@ -0,0 +1,237 @@
+/*
+ * Copyright 2011-2012 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/ {
+	chosen {
+		bootargs = "console=ttyAMA0";
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&intc>;
+
+		sata at ffe08000 {
+			compatible = "calxeda,hb-ahci";
+			reg = <0xffe08000 0x10000>;
+			interrupts = <0 83 4>;
+			dma-coherent;
+			calxeda,port-phys = <&combophy5 0 &combophy0 0
+					     &combophy0 1 &combophy0 2
+					     &combophy0 3>;
+		};
+
+		sdhci at ffe0e000 {
+			compatible = "calxeda,hb-sdhci";
+			reg = <0xffe0e000 0x1000>;
+			interrupts = <0 90 4>;
+			clocks = <&eclk>;
+			status = "disabled";
+		};
+
+		memory-controller at fff00000 {
+			compatible = "calxeda,hb-ddr-ctrl";
+			reg = <0xfff00000 0x1000>;
+			interrupts = <0 91 4>;
+		};
+
+		ipc at fff20000 {
+			compatible = "arm,pl320", "arm,primecell";
+			reg = <0xfff20000 0x1000>;
+			interrupts = <0 7 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		gpioe: gpio at fff30000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff30000 0x1000>;
+			interrupts = <0 14 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpiof: gpio at fff31000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff31000 0x1000>;
+			interrupts = <0 15 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpiog: gpio at fff32000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff32000 0x1000>;
+			interrupts = <0 16 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		gpioh: gpio at fff33000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff33000 0x1000>;
+			interrupts = <0 17 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+			status = "disabled";
+		};
+
+		timer at fff34000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xfff34000 0x1000>;
+			interrupts = <0 18 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		rtc at fff35000 {
+			compatible = "arm,pl031", "arm,primecell";
+			reg = <0xfff35000 0x1000>;
+			interrupts = <0 19 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		serial at fff36000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xfff36000 0x1000>;
+			interrupts = <0 20 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		smic at fff3a000 {
+			compatible = "ipmi-smic";
+			device_type = "ipmi";
+			reg = <0xfff3a000 0x1000>;
+			interrupts = <0 24 4>;
+			reg-size = <4>;
+			reg-spacing = <4>;
+		};
+
+		sregs at fff3c000 {
+			compatible = "calxeda,hb-sregs";
+			reg = <0xfff3c000 0x1000>;
+
+			clocks {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				osc: oscillator {
+					#clock-cells = <0>;
+					compatible = "fixed-clock";
+					clock-frequency = <33333000>;
+				};
+
+				ddrpll: ddrpll {
+					#clock-cells = <0>;
+					compatible = "calxeda,hb-pll-clock";
+					clocks = <&osc>;
+					reg = <0x108>;
+				};
+
+				a9pll: a9pll {
+					#clock-cells = <0>;
+					compatible = "calxeda,hb-pll-clock";
+					clocks = <&osc>;
+					reg = <0x100>;
+				};
+
+				a9periphclk: a9periphclk {
+					#clock-cells = <0>;
+					compatible = "calxeda,hb-a9periph-clock";
+					clocks = <&a9pll>;
+					reg = <0x104>;
+				};
+
+				a9bclk: a9bclk {
+					#clock-cells = <0>;
+					compatible = "calxeda,hb-a9bus-clock";
+					clocks = <&a9pll>;
+					reg = <0x104>;
+				};
+
+				emmcpll: emmcpll {
+					#clock-cells = <0>;
+					compatible = "calxeda,hb-pll-clock";
+					clocks = <&osc>;
+					reg = <0x10C>;
+				};
+
+				eclk: eclk {
+					#clock-cells = <0>;
+					compatible = "calxeda,hb-emmc-clock";
+					clocks = <&emmcpll>;
+					reg = <0x114>;
+				};
+
+				pclk: pclk {
+					#clock-cells = <0>;
+					compatible = "fixed-clock";
+					clock-frequency = <150000000>;
+				};
+			};
+		};
+
+		dma at fff3d000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0xfff3d000 0x1000>;
+			interrupts = <0 92 4>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		ethernet at fff50000 {
+			compatible = "calxeda,hb-xgmac";
+			reg = <0xfff50000 0x1000>;
+			interrupts = <0 77 4  0 78 4  0 79 4>;
+			dma-coherent;
+		};
+
+		ethernet at fff51000 {
+			compatible = "calxeda,hb-xgmac";
+			reg = <0xfff51000 0x1000>;
+			interrupts = <0 80 4  0 81 4  0 82 4>;
+			dma-coherent;
+		};
+
+		combophy0: combo-phy at fff58000 {
+			compatible = "calxeda,hb-combophy";
+			#phy-cells = <1>;
+			reg = <0xfff58000 0x1000>;
+			phydev = <5>;
+		};
+
+		combophy5: combo-phy at fff5d000 {
+			compatible = "calxeda,hb-combophy";
+			#phy-cells = <1>;
+			reg = <0xfff5d000 0x1000>;
+			phydev = <31>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/highbank.dts b/arch/arm/boot/dts/highbank.dts
index e39a79a..a9ae5d3 100644
--- a/arch/arm/boot/dts/highbank.dts
+++ b/arch/arm/boot/dts/highbank.dts
@@ -69,16 +69,8 @@
 		reg = <0x00000000 0xff900000>;
 	};
 
-	chosen {
-		bootargs = "console=ttyAMA0";
-	};
-
 	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		interrupt-parent = <&intc>;
-		ranges;
+		ranges = <0x00000000 0x00000000 0xffffffff>;
 
 		timer at fff10600 {
 			compatible = "arm,cortex-a9-twd-timer";
@@ -117,178 +109,6 @@
 			interrupts = <0 76 4  0 75 4  0 74 4  0 73 4>;
 		};
 
-		sata at ffe08000 {
-			compatible = "calxeda,hb-ahci";
-			reg = <0xffe08000 0x10000>;
-			interrupts = <0 83 4>;
-			calxeda,port-phys = <&combophy5 0 &combophy0 0
-					     &combophy0 1 &combophy0 2
-					     &combophy0 3>;
-			dma-coherent;
-		};
-
-		sdhci at ffe0e000 {
-			compatible = "calxeda,hb-sdhci";
-			reg = <0xffe0e000 0x1000>;
-			interrupts = <0 90 4>;
-			clocks = <&eclk>;
-			status = "disabled";
-		};
-
-		memory-controller at fff00000 {
-			compatible = "calxeda,hb-ddr-ctrl";
-			reg = <0xfff00000 0x1000>;
-			interrupts = <0 91 4>;
-		};
-
-		ipc at fff20000 {
-			compatible = "arm,pl320", "arm,primecell";
-			reg = <0xfff20000 0x1000>;
-			interrupts = <0 7 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-		};
-
-		gpioe: gpio at fff30000 {
-			#gpio-cells = <2>;
-			compatible = "arm,pl061", "arm,primecell";
-			gpio-controller;
-			reg = <0xfff30000 0x1000>;
-			interrupts = <0 14 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-			status = "disabled";
-		};
-
-		gpiof: gpio at fff31000 {
-			#gpio-cells = <2>;
-			compatible = "arm,pl061", "arm,primecell";
-			gpio-controller;
-			reg = <0xfff31000 0x1000>;
-			interrupts = <0 15 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-			status = "disabled";
-		};
-
-		gpiog: gpio at fff32000 {
-			#gpio-cells = <2>;
-			compatible = "arm,pl061", "arm,primecell";
-			gpio-controller;
-			reg = <0xfff32000 0x1000>;
-			interrupts = <0 16 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-			status = "disabled";
-		};
-
-		gpioh: gpio at fff33000 {
-			#gpio-cells = <2>;
-			compatible = "arm,pl061", "arm,primecell";
-			gpio-controller;
-			reg = <0xfff33000 0x1000>;
-			interrupts = <0 17 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-			status = "disabled";
-		};
-
-		timer {
-			compatible = "arm,sp804", "arm,primecell";
-			reg = <0xfff34000 0x1000>;
-			interrupts = <0 18 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-		};
-
-		rtc at fff35000 {
-			compatible = "arm,pl031", "arm,primecell";
-			reg = <0xfff35000 0x1000>;
-			interrupts = <0 19 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-		};
-
-		serial at fff36000 {
-			compatible = "arm,pl011", "arm,primecell";
-			reg = <0xfff36000 0x1000>;
-			interrupts = <0 20 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-		};
-
-		smic at fff3a000 {
-			compatible = "ipmi-smic";
-			device_type = "ipmi";
-			reg = <0xfff3a000 0x1000>;
-			interrupts = <0 24 4>;
-			reg-size = <4>;
-			reg-spacing = <4>;
-		};
-
-		sregs at fff3c000 {
-			compatible = "calxeda,hb-sregs";
-			reg = <0xfff3c000 0x1000>;
-
-			clocks {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				osc: oscillator {
-					#clock-cells = <0>;
-					compatible = "fixed-clock";
-					clock-frequency = <33333000>;
-				};
-
-				ddrpll: ddrpll {
-					#clock-cells = <0>;
-					compatible = "calxeda,hb-pll-clock";
-					clocks = <&osc>;
-					reg = <0x108>;
-				};
-
-				a9pll: a9pll {
-					#clock-cells = <0>;
-					compatible = "calxeda,hb-pll-clock";
-					clocks = <&osc>;
-					reg = <0x100>;
-				};
-
-				a9periphclk: a9periphclk {
-					#clock-cells = <0>;
-					compatible = "calxeda,hb-a9periph-clock";
-					clocks = <&a9pll>;
-					reg = <0x104>;
-				};
-
-				a9bclk: a9bclk {
-					#clock-cells = <0>;
-					compatible = "calxeda,hb-a9bus-clock";
-					clocks = <&a9pll>;
-					reg = <0x104>;
-				};
-
-				emmcpll: emmcpll {
-					#clock-cells = <0>;
-					compatible = "calxeda,hb-pll-clock";
-					clocks = <&osc>;
-					reg = <0x10C>;
-				};
-
-				eclk: eclk {
-					#clock-cells = <0>;
-					compatible = "calxeda,hb-emmc-clock";
-					clocks = <&emmcpll>;
-					reg = <0x114>;
-				};
-
-				pclk: pclk {
-					#clock-cells = <0>;
-					compatible = "fixed-clock";
-					clock-frequency = <150000000>;
-				};
-			};
-		};
 
 		sregs at fff3c200 {
 			compatible = "calxeda,hb-sregs-l2-ecc";
@@ -296,40 +116,7 @@
 			interrupts = <0 71 4  0 72 4>;
 		};
 
-		dma at fff3d000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0xfff3d000 0x1000>;
-			interrupts = <0 92 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
-		};
-
-		ethernet at fff50000 {
-			compatible = "calxeda,hb-xgmac";
-			reg = <0xfff50000 0x1000>;
-			interrupts = <0 77 4  0 78 4  0 79 4>;
-			dma-coherent;
-		};
-
-		ethernet at fff51000 {
-			compatible = "calxeda,hb-xgmac";
-			reg = <0xfff51000 0x1000>;
-			interrupts = <0 80 4  0 81 4  0 82 4>;
-			dma-coherent;
-		};
-
-		combophy0: combo-phy at fff58000 {
-			compatible = "calxeda,hb-combophy";
-			#phy-cells = <1>;
-			reg = <0xfff58000 0x1000>;
-			phydev = <5>;
-		};
-
-		combophy5: combo-phy at fff5d000 {
-			compatible = "calxeda,hb-combophy";
-			#phy-cells = <1>;
-			reg = <0xfff5d000 0x1000>;
-			phydev = <31>;
-		};
 	};
 };
+
+/include/ "ecx-common.dtsi"
-- 
1.7.10.4

[PATCH 4/6] ARM: smp_twd: don't warn on no DT node

[Rob Herring]

From: Rob Herring <rob.herring@calxeda.com>

Not having a TWD is valid if we have multiple platforms with different
cores, so remove the warning message.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
---
 arch/arm/kernel/smp_twd.c |    6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/kernel/smp_twd.c b/arch/arm/kernel/smp_twd.c
index e1f9069..e52e80a 100644
--- a/arch/arm/kernel/smp_twd.c
+++ b/arch/arm/kernel/smp_twd.c
@@ -366,10 +366,8 @@ void __init twd_local_timer_of_register(void)
 	int err;
 
 	np = of_find_matching_node(NULL, twd_of_match);
-	if (!np) {
-		err = -ENODEV;
-		goto out;
-	}
+	if (!np)
+		return -ENODEV;
 
 	twd_ppi = irq_of_parse_and_map(np, 0);
 	if (!twd_ppi) {
-- 
1.7.10.4

[PATCH 5/6] ARM: highbank: abstract out SCU usage

[Rob Herring]

From: Rob Herring <rob.herring@calxeda.com>

In preparation for A15 support on ECX-2000, the direct calls to SCU
registers must be conditional. The SCU power mode register is replaced by
a custom register on ECX-2000.

Rather than read the number of cores from the SCU, just hardcode it to 4.
This removes one use of SCU and removes the need for the SCU to be
statically mapped. The cpu initialization will ultimately come from DT.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
---
 arch/arm/mach-highbank/highbank.c |   21 +++++----------------
 arch/arm/mach-highbank/hotplug.c  |    6 ++----
 arch/arm/mach-highbank/platsmp.c  |    7 +++----
 arch/arm/mach-highbank/pm.c       |    3 ---
 arch/arm/mach-highbank/sysregs.h  |   19 +++++++++++++++++++
 arch/arm/mach-highbank/system.c   |    2 --
 6 files changed, 29 insertions(+), 29 deletions(-)

diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c
index 40e36a5..3da921a 100644
--- a/arch/arm/mach-highbank/highbank.c
+++ b/arch/arm/mach-highbank/highbank.c
@@ -28,30 +28,19 @@
 
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
-#include <asm/smp_scu.h>
 #include <asm/smp_twd.h>
 #include <asm/hardware/arm_timer.h>
 #include <asm/hardware/timer-sp.h>
 #include <asm/hardware/gic.h>
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/arch.h>
-#include <asm/mach/map.h>
 #include <asm/mach/time.h>
 
 #include "core.h"
 #include "sysregs.h"
 
 void __iomem *sregs_base;
-
-#define HB_SCU_VIRT_BASE	0xfee00000
-void __iomem *scu_base_addr = ((void __iomem *)(HB_SCU_VIRT_BASE));
-
-static struct map_desc scu_io_desc __initdata = {
-	.virtual	= HB_SCU_VIRT_BASE,
-	.pfn		= 0, /* run-time */
-	.length		= SZ_4K,
-	.type		= MT_DEVICE,
-};
+void __iomem *scu_base_addr;
 
 static void __init highbank_scu_map_io(void)
 {
@@ -60,13 +49,11 @@ static void __init highbank_scu_map_io(void)
 	/* Get SCU base */
 	asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (base));
 
-	scu_io_desc.pfn = __phys_to_pfn(base);
-	iotable_init(&scu_io_desc, 1);
+	scu_base_addr = ioremap(base, SZ_4K);
 }
 
 static void __init highbank_map_io(void)
 {
-	highbank_scu_map_io();
 	highbank_lluart_map_io();
 }
 
@@ -99,6 +86,9 @@ static void __init highbank_init_irq(void)
 {
 	of_irq_init(irq_match);
 
+	if (of_find_compatible_node(NULL, NULL, "arm,cortex-a9"))
+		highbank_scu_map_io();
+
 #ifdef CONFIG_CACHE_L2X0
 	/* Enable PL310 L2 Cache controller */
 	highbank_smc1(0x102, 0x1);
@@ -145,7 +135,6 @@ static struct sys_timer highbank_timer = {
 static void highbank_power_off(void)
 {
 	hignbank_set_pwr_shutdown();
-	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
 
 	while (1)
 		cpu_do_idle();
diff --git a/arch/arm/mach-highbank/hotplug.c b/arch/arm/mach-highbank/hotplug.c
index 2c1b8c3..7b60fac 100644
--- a/arch/arm/mach-highbank/hotplug.c
+++ b/arch/arm/mach-highbank/hotplug.c
@@ -14,13 +14,11 @@
  * this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 #include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/smp.h>
 
-#include <asm/smp_scu.h>
 #include <asm/cacheflush.h>
 
 #include "core.h"
+#include "sysregs.h"
 
 extern void secondary_startup(void);
 
@@ -33,7 +31,7 @@ void __ref highbank_cpu_die(unsigned int cpu)
 	flush_cache_all();
 
 	highbank_set_cpu_jump(cpu, secondary_startup);
-	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+	highbank_set_core_pwr();
 
 	cpu_do_idle();
 
diff --git a/arch/arm/mach-highbank/platsmp.c b/arch/arm/mach-highbank/platsmp.c
index fa9560e..1129957 100644
--- a/arch/arm/mach-highbank/platsmp.c
+++ b/arch/arm/mach-highbank/platsmp.c
@@ -42,9 +42,7 @@ static int __cpuinit highbank_boot_secondary(unsigned int cpu, struct task_struc
  */
 static void __init highbank_smp_init_cpus(void)
 {
-	unsigned int i, ncores;
-
-	ncores = scu_get_core_count(scu_base_addr);
+	unsigned int i, ncores = 4;
 
 	/* sanity check */
 	if (ncores > NR_CPUS) {
@@ -65,7 +63,8 @@ static void __init highbank_smp_prepare_cpus(unsigned int max_cpus)
 {
 	int i;
 
-	scu_enable(scu_base_addr);
+	if (scu_base_addr)
+		scu_enable(scu_base_addr);
 
 	/*
 	 * Write the address of secondary startup into the jump table
diff --git a/arch/arm/mach-highbank/pm.c b/arch/arm/mach-highbank/pm.c
index de866f2..74aa135 100644
--- a/arch/arm/mach-highbank/pm.c
+++ b/arch/arm/mach-highbank/pm.c
@@ -19,7 +19,6 @@
 #include <linux/suspend.h>
 
 #include <asm/proc-fns.h>
-#include <asm/smp_scu.h>
 #include <asm/suspend.h>
 
 #include "core.h"
@@ -35,8 +34,6 @@ static int highbank_pm_enter(suspend_state_t state)
 {
 	hignbank_set_pwr_suspend();
 	highbank_set_cpu_jump(0, cpu_resume);
-
-	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
 	cpu_suspend(0, highbank_suspend_finish);
 
 	return 0;
diff --git a/arch/arm/mach-highbank/sysregs.h b/arch/arm/mach-highbank/sysregs.h
index 0e91338..e13e8ea 100644
--- a/arch/arm/mach-highbank/sysregs.h
+++ b/arch/arm/mach-highbank/sysregs.h
@@ -17,6 +17,10 @@
 #define _MACH_HIGHBANK__SYSREGS_H_
 
 #include <linux/io.h>
+#include <linux/smp.h>
+#include <asm/smp_plat.h>
+#include <asm/smp_scu.h>
+#include "core.h"
 
 extern void __iomem *sregs_base;
 
@@ -29,24 +33,39 @@ extern void __iomem *sregs_base;
 #define HB_PWR_HARD_RESET		2
 #define HB_PWR_SHUTDOWN			3
 
+#define SREG_CPU_PWR_CTRL(c)		(0x200 + ((c) * 4))
+
+static inline void highbank_set_core_pwr(void)
+{
+	int cpu = cpu_logical_map(smp_processor_id());
+	if (scu_base_addr)
+		scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+	else
+		writel_relaxed(1, sregs_base + SREG_CPU_PWR_CTRL(cpu));
+}
+
 static inline void hignbank_set_pwr_suspend(void)
 {
 	writel(HB_PWR_SUSPEND, sregs_base + HB_SREG_A9_PWR_REQ);
+	highbank_set_core_pwr();
 }
 
 static inline void hignbank_set_pwr_shutdown(void)
 {
 	writel(HB_PWR_SHUTDOWN, sregs_base + HB_SREG_A9_PWR_REQ);
+	highbank_set_core_pwr();
 }
 
 static inline void hignbank_set_pwr_soft_reset(void)
 {
 	writel(HB_PWR_SOFT_RESET, sregs_base + HB_SREG_A9_PWR_REQ);
+	highbank_set_core_pwr();
 }
 
 static inline void hignbank_set_pwr_hard_reset(void)
 {
 	writel(HB_PWR_HARD_RESET, sregs_base + HB_SREG_A9_PWR_REQ);
+	highbank_set_core_pwr();
 }
 
 #endif
diff --git a/arch/arm/mach-highbank/system.c b/arch/arm/mach-highbank/system.c
index 82c2723..194a5bb 100644
--- a/arch/arm/mach-highbank/system.c
+++ b/arch/arm/mach-highbank/system.c
@@ -14,7 +14,6 @@
  * this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 #include <linux/io.h>
-#include <asm/smp_scu.h>
 #include <asm/proc-fns.h>
 
 #include "core.h"
@@ -27,7 +26,6 @@ void highbank_restart(char mode, const char *cmd)
 	else
 		hignbank_set_pwr_soft_reset();
 
-	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
 	cpu_do_idle();
 }
 
-- 
1.7.10.4

[PATCH 6/6] ARM: highbank: Add initial ECX-2000 support

[Rob Herring]

From: Rob Herring <rob.herring@calxeda.com>

And initial Calxeda ECX-2000 SOC support. This adds Cortex-A15 peripherals
and machine DT match name.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
---
 arch/arm/mach-highbank/Kconfig    |    2 +-
 arch/arm/mach-highbank/highbank.c |    6 ++++++
 2 files changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-highbank/Kconfig b/arch/arm/mach-highbank/Kconfig
index 0e1d0a4..551c97e 100644
--- a/arch/arm/mach-highbank/Kconfig
+++ b/arch/arm/mach-highbank/Kconfig
@@ -1,5 +1,5 @@
 config ARCH_HIGHBANK
-	bool "Calxeda ECX-1000 (Highbank)" if ARCH_MULTI_V7
+	bool "Calxeda ECX-1000/2000 (Highbank/Midway)" if ARCH_MULTI_V7
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARM_AMBA
 	select ARM_GIC
diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c
index 3da921a..3e60e57 100644
--- a/arch/arm/mach-highbank/highbank.c
+++ b/arch/arm/mach-highbank/highbank.c
@@ -26,6 +26,7 @@
 #include <linux/smp.h>
 #include <linux/amba/bus.h>
 
+#include <asm/arch_timer.h>
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
 #include <asm/smp_twd.h>
@@ -70,6 +71,7 @@ void highbank_set_cpu_jump(int cpu, void *jump_addr)
 }
 
 const static struct of_device_id irq_match[] = {
+	{ .compatible = "arm,cortex-a15-gic", .data = gic_of_init, },
 	{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
 	{}
 };
@@ -126,6 +128,9 @@ static void __init highbank_timer_init(void)
 	sp804_clockevents_init(timer_base, irq, "timer0");
 
 	twd_local_timer_of_register();
+
+	arch_timer_of_register();
+	arch_timer_sched_clock_init();
 }
 
 static struct sys_timer highbank_timer = {
@@ -200,6 +205,7 @@ static void __init highbank_init(void)
 
 static const char *highbank_match[] __initconst = {
 	"calxeda,highbank",
+	"calxeda,ecx-2000",
 	NULL,
 };
 
-- 
1.7.10.4

[PATCH 0/6] Initial Calxeda ECX-2000 support

[Arnd Bergmann]

On Friday 26 October 2012, Rob Herring wrote:
> From: Rob Herring <rob.herring@calxeda.com>
> 
> This series adds initial support for Calxeda A15 based ECX-2000 SOC. Most
> of the changes are shuffling of dts files to share common parts between
> highbank (ECX-1000) and ECX-2000 and abstracting out or removing SCU
> accesses as the A15 has no SCU registers.
> 
> Although the highbank name really refers to 1st gen SOC, the highbank
> name in the kernel is now referring to both SOCs.

The patches all look good to me,

Acked-by: Arnd Bergmann <arnd@arndb.de>