[PATCH 1/1] ARM: ux500: Change IRQ from low-to-high edge triggered to high-to-low

[PATCH 1/1] ARM: ux500: Change IRQ from low-to-high edge triggered to high-to-low

[Lee Jones]

When the STMPE IRQ is triggered to be active high level-sensitive, the
Nomadik GPIO controller it uses complains, although it still works.
Recently we attempted to move triggering to low-to-high in an attempt
to prevent the warning; however, this ensured that the IRQ was actually
missed completely. Now we have a solution which both works and keeps the
GPIO controller happy.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 arch/arm/boot/dts/stuib.dtsi |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stuib.dtsi b/arch/arm/boot/dts/stuib.dtsi
index 39446a2..615392a 100644
--- a/arch/arm/boot/dts/stuib.dtsi
+++ b/arch/arm/boot/dts/stuib.dtsi
@@ -15,7 +15,7 @@
 			stmpe1601: stmpe1601 at 40 {
 				compatible = "st,stmpe1601";
 				reg = <0x40>;
-				interrupts = <26 0x1>;
+				interrupts = <26 0x2>;
 				interrupt-parent = <&gpio6>;
 				interrupt-controller;
 
-- 
1.7.9.5

[PATCH 1/1] ARM: ux500: Change IRQ from low-to-high edge triggered to high-to-low

[Linus Walleij]

On Fri, Nov 30, 2012 at 4:24 PM, Lee Jones <lee.jones@linaro.org> wrote:

> When the STMPE IRQ is triggered to be active high level-sensitive, the
> Nomadik GPIO controller it uses complains, although it still works.
> Recently we attempted to move triggering to low-to-high in an attempt
> to prevent the warning; however, this ensured that the IRQ was actually
> missed completely. Now we have a solution which both works and keeps the
> GPIO controller happy.
>
> Signed-off-by: Lee Jones <lee.jones@linaro.org>

Acked-by: Linus Walleij <linus.walleij@linaro.org>

Is this something I should put into the ux500 tree or will you
take care of this in a separate pull request?

Yours,
Linus Walleij

[PATCH 1/1] ARM: ux500: Change IRQ from low-to-high edge triggered to high-to-low

[Lee Jones]

On Sat, 01 Dec 2012, Linus Walleij wrote:

> On Fri, Nov 30, 2012 at 4:24 PM, Lee Jones <lee.jones@linaro.org> wrote:
> 
> > When the STMPE IRQ is triggered to be active high level-sensitive, the
> > Nomadik GPIO controller it uses complains, although it still works.
> > Recently we attempted to move triggering to low-to-high in an attempt
> > to prevent the warning; however, this ensured that the IRQ was actually
> > missed completely. Now we have a solution which both works and keeps the
> > GPIO controller happy.
> >
> > Signed-off-by: Lee Jones <lee.jones@linaro.org>
> 
> Acked-by: Linus Walleij <linus.walleij@linaro.org>
> 
> Is this something I should put into the ux500 tree or will you
> take care of this in a separate pull request?

Can you still get this into the RCs, as it's a bugfix?

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 1/1] ARM: ux500: Change IRQ from low-to-high edge triggered to high-to-low

[Linus Walleij]

On Tue, Dec 4, 2012 at 10:12 AM, Lee Jones <lee.jones@linaro.org> wrote:
> On Sat, 01 Dec 2012, Linus Walleij wrote:
>
>> On Fri, Nov 30, 2012 at 4:24 PM, Lee Jones <lee.jones@linaro.org> wrote:
>>
>> > When the STMPE IRQ is triggered to be active high level-sensitive, the
>> > Nomadik GPIO controller it uses complains, although it still works.
>> > Recently we attempted to move triggering to low-to-high in an attempt
>> > to prevent the warning; however, this ensured that the IRQ was actually
>> > missed completely. Now we have a solution which both works and keeps the
>> > GPIO controller happy.
>> >
>> > Signed-off-by: Lee Jones <lee.jones@linaro.org>
>>
>> Acked-by: Linus Walleij <linus.walleij@linaro.org>
>>
>> Is this something I should put into the ux500 tree or will you
>> take care of this in a separate pull request?
>
> Can you still get this into the RCs, as it's a bugfix?

Well it doesn't apply to the -rc:s since it's patching
arch/arm/boot/dts/stuib.dtsi which does not exist in
the v3.7 series.

Either what you want is to submit a fix to Arnd & Olof
on top of your previous DT patches, or you need to send
a rebased version...

Yours,
Linus Walleij

[PATCH 1/1] ARM: ux500: Change IRQ from low-to-high edge triggered to high-to-low

[Lee Jones]

On Tue, 04 Dec 2012, Linus Walleij wrote:

> On Tue, Dec 4, 2012 at 10:12 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > On Sat, 01 Dec 2012, Linus Walleij wrote:
> >
> >> On Fri, Nov 30, 2012 at 4:24 PM, Lee Jones <lee.jones@linaro.org> wrote:
> >>
> >> > When the STMPE IRQ is triggered to be active high level-sensitive, the
> >> > Nomadik GPIO controller it uses complains, although it still works.
> >> > Recently we attempted to move triggering to low-to-high in an attempt
> >> > to prevent the warning; however, this ensured that the IRQ was actually
> >> > missed completely. Now we have a solution which both works and keeps the
> >> > GPIO controller happy.
> >> >
> >> > Signed-off-by: Lee Jones <lee.jones@linaro.org>
> >>
> >> Acked-by: Linus Walleij <linus.walleij@linaro.org>
> >>
> >> Is this something I should put into the ux500 tree or will you
> >> take care of this in a separate pull request?
> >
> > Can you still get this into the RCs, as it's a bugfix?
> 
> Well it doesn't apply to the -rc:s since it's patching
> arch/arm/boot/dts/stuib.dtsi which does not exist in
> the v3.7 series.
> 
> Either what you want is to submit a fix to Arnd & Olof
> on top of your previous DT patches, or you need to send
> a rebased version...

Ah, well if it's fixing something that isn't in the -rc:s, then
it doesn't need to go into the -rc:s. Well as the merge window
is not long opening, I'll hold on to it and stick it in for -rc1
or something.

Thanks for letting me know.

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog