[PATCH v5 0/2] ARM: davinci: add support for dm365 vpbe display

[PATCH v5 0/2] ARM: davinci: add support for dm365 vpbe display

[Prabhakar Lad]

From: Lad, Prabhakar <prabhakar.lad@ti.com>

This patch series enables VPBE display driver on DM365.

Changes for v5:
1: pass different platform names to handle different ip's.
2: Fixed review comments pointed by Sekhar.

Changes for v4:
1: Replaced the obsolete preset API by timings API.

Changes for v3:
1: Removed VPSS clock alias for master and slave which was
   sent for VPSS driver. since this patch was dependent on
   patch[1]. I will revist this patch once MC(captrure driver)
   goes into mainline.
[1] http://www.spinics.net/lists/linux-media/msg50562.html

Changes for v2:
1: Added VPSS clock so that capture and display
   can work independent.

Manjunath Hadli (2):
  ARM: davinci: dm365: add support for v4l2 video display
  ARM: davinci: dm365 EVM: add support for VPBE display

 arch/arm/mach-davinci/board-dm365-evm.c |  179 +++++++++++++++++++++++++++-
 arch/arm/mach-davinci/davinci.h         |    2 +-
 arch/arm/mach-davinci/dm365.c           |  203 +++++++++++++++++++++++++++++--
 3 files changed, 370 insertions(+), 14 deletions(-)

-- 
1.7.4.1

[PATCH v5 1/2] ARM: davinci: dm365: add support for v4l2 video display

[Prabhakar Lad]

From: Manjunath Hadli <manjunath.hadli@ti.com>

Create platform devices for various video modules like venc,osd,
vpbe and v4l2 driver for dm365.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
---
 arch/arm/mach-davinci/board-dm365-evm.c |    4 +-
 arch/arm/mach-davinci/davinci.h         |    2 +-
 arch/arm/mach-davinci/dm365.c           |  203 +++++++++++++++++++++++++++++--
 3 files changed, 195 insertions(+), 14 deletions(-)

diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
index 1b4a8ad..0c3dae6 100644
--- a/arch/arm/mach-davinci/board-dm365-evm.c
+++ b/arch/arm/mach-davinci/board-dm365-evm.c
@@ -564,8 +564,6 @@ static struct davinci_uart_config uart_config __initdata = {
 
 static void __init dm365_evm_map_io(void)
 {
-	/* setup input configuration for VPFE input devices */
-	dm365_set_vpfe_config(&vpfe_cfg);
 	dm365_init();
 }
 
@@ -597,6 +595,8 @@ static __init void dm365_evm_init(void)
 
 	davinci_setup_mmc(0, &dm365evm_mmc_config);
 
+	dm365_init_video(&vpfe_cfg, NULL);
+
 	/* maybe setup mmc1/etc ... _after_ mmc0 */
 	evm_init_cpld();
 
diff --git a/arch/arm/mach-davinci/davinci.h b/arch/arm/mach-davinci/davinci.h
index 12d544b..1c2670f 100644
--- a/arch/arm/mach-davinci/davinci.h
+++ b/arch/arm/mach-davinci/davinci.h
@@ -84,7 +84,7 @@ void __init dm365_init_ks(struct davinci_ks_platform_data *pdata);
 void __init dm365_init_rtc(void);
 void dm365_init_spi0(unsigned chipselect_mask,
 			const struct spi_board_info *info, unsigned len);
-void dm365_set_vpfe_config(struct vpfe_config *cfg);
+int __init dm365_init_video(struct vpfe_config *, struct vpbe_config *);
 
 /* DM644x function declarations */
 void __init dm644x_init(void);
diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c
index b680c83..cada153 100644
--- a/arch/arm/mach-davinci/dm365.c
+++ b/arch/arm/mach-davinci/dm365.c
@@ -40,10 +40,16 @@
 
 #define DM365_REF_FREQ		24000000	/* 24 MHz on the DM365 EVM */
 
+#define DM3XX_VDAC_CONFIG		0x01c4002c
+
+#define DM365_RTC_BASE			0x01c69000
+
 /* Base of key scan register bank */
 #define DM365_KEYSCAN_BASE		0x01c69400
 
-#define DM365_RTC_BASE			0x01c69000
+#define DM365_OSD_REG_BASE		0x01c71c00
+
+#define DM365_VENC_REG_BASE		0x01c71e00
 
 #define DAVINCI_DM365_VC_BASE		0x01d0c000
 #define DAVINCI_DMA_VC_TX		2
@@ -56,6 +62,11 @@
 #define DM365_EMAC_CNTRL_RAM_OFFSET	0x1000
 #define DM365_EMAC_CNTRL_RAM_SIZE	0x2000
 
+#define DM365_VPSS_CLK_CTRL_ADDR		0x44
+#define DM365_VPSS_VENCCLKEN_ENABLE		BIT(3)
+#define DM365_VPSS_DACCLKEN_ENABLE		BIT(4)
+#define DM365_VPSS_PLLC2SYSCLK5_ENABLE		(BIT(5) & ~BIT(6))
+
 static struct pll_data pll1_data = {
 	.num		= 1,
 	.phys_base	= DAVINCI_PLL1_BASE,
@@ -1232,6 +1243,186 @@ static struct platform_device dm365_isif_dev = {
 	},
 };
 
+static struct resource dm365_osd_resources[] = {
+	{
+		.start = DM365_OSD_REG_BASE,
+		.end   = DM365_OSD_REG_BASE + 0x100,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static u64 dm365_video_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device dm365_osd_dev = {
+	.name		= DM365_VPBE_OSD_SUBDEV_NAME,
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(dm365_osd_resources),
+	.resource	= dm365_osd_resources,
+	.dev		= {
+		.dma_mask		= &dm365_video_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+static struct resource dm365_venc_resources[] = {
+	{
+		.start = IRQ_VENCINT,
+		.end   = IRQ_VENCINT,
+		.flags = IORESOURCE_IRQ,
+	},
+	/* venc registers io space */
+	{
+		.start = DM365_VENC_REG_BASE,
+		.end   = DM365_VENC_REG_BASE + 0x180,
+		.flags = IORESOURCE_MEM,
+	},
+	/* vdaccfg registers io space */
+	{
+		.start = DM3XX_VDAC_CONFIG,
+		.end   = DM3XX_VDAC_CONFIG + 4,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct resource dm365_v4l2_disp_resources[] = {
+	{
+		.start = IRQ_VENCINT,
+		.end   = IRQ_VENCINT,
+		.flags = IORESOURCE_IRQ,
+	},
+	/* venc registers io space */
+	{
+		.start = DM365_VENC_REG_BASE,
+		.end   = DM365_VENC_REG_BASE + 0x180,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static int dm365_vpbe_setup_pinmux(enum v4l2_mbus_pixelcode if_type,
+			    int field)
+{
+	switch (if_type) {
+	case V4L2_MBUS_FMT_SGRBG8_1X8:
+		davinci_cfg_reg(DM365_VOUT_FIELD_G81);
+		davinci_cfg_reg(DM365_VOUT_COUTL_EN);
+		davinci_cfg_reg(DM365_VOUT_COUTH_EN);
+		break;
+
+	case V4L2_MBUS_FMT_YUYV10_1X20:
+		if (field)
+			davinci_cfg_reg(DM365_VOUT_FIELD);
+		else
+			davinci_cfg_reg(DM365_VOUT_FIELD_G81);
+		davinci_cfg_reg(DM365_VOUT_COUTL_EN);
+		davinci_cfg_reg(DM365_VOUT_COUTH_EN);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int dm365_venc_setup_clock(enum vpbe_enc_timings_type type,
+				  unsigned int pclock)
+{
+	void __iomem *vpss_clkctl_reg;
+	u32 val;
+
+	vpss_clkctl_reg = DAVINCI_SYSMOD_VIRT(DM365_VPSS_CLK_CTRL_ADDR);
+
+	switch (type) {
+	case VPBE_ENC_STD:
+		vpss_enable_clock(VPSS_VENC_CLOCK_SEL, 1);
+		vpss_enable_clock(VPSS_VPBE_CLOCK, 1);
+		val = DM365_VPSS_VENCCLKEN_ENABLE | DM365_VPSS_DACCLKEN_ENABLE;
+		break;
+
+	case VPBE_ENC_CUSTOM_TIMINGS:
+		if (pclock <= 27000000) {
+			vpss_enable_clock(VPSS_VENC_CLOCK_SEL, 1);
+			vpss_enable_clock(VPSS_VPBE_CLOCK, 1);
+			val = DM365_VPSS_VENCCLKEN_ENABLE |
+			      DM365_VPSS_DACCLKEN_ENABLE;
+		} else {
+			/* set sysclk4 to output 74.25 MHz from pll1 */
+			val = DM365_VPSS_PLLC2SYSCLK5_ENABLE |
+			      DM365_VPSS_DACCLKEN_ENABLE |
+			      DM365_VPSS_VENCCLKEN_ENABLE;
+		}
+		break;
+
+	default:
+		return -EINVAL;
+	}
+	writel(val, vpss_clkctl_reg);
+
+	return 0;
+}
+
+static struct platform_device dm365_vpbe_display = {
+	.name		= "vpbe-v4l2",
+	.id		= -1,
+	.num_resources  = ARRAY_SIZE(dm365_v4l2_disp_resources),
+	.resource	= dm365_v4l2_disp_resources,
+	.dev		= {
+		.dma_mask		= &dm365_video_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+struct venc_platform_data dm365_venc_pdata = {
+	.setup_pinmux	= dm365_vpbe_setup_pinmux,
+	.setup_clock	= dm365_venc_setup_clock,
+};
+
+static struct platform_device dm365_venc_dev = {
+	.name		= DM365_VPBE_VENC_SUBDEV_NAME,
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(dm365_venc_resources),
+	.resource	= dm365_venc_resources,
+	.dev		= {
+		.dma_mask		= &dm365_video_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= (void *)&dm365_venc_pdata,
+	},
+};
+
+static struct platform_device dm365_vpbe_dev = {
+	.name		= "vpbe_controller",
+	.id		= -1,
+	.dev		= {
+		.dma_mask		= &dm365_video_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+int __init dm365_init_video(struct vpfe_config *vpfe_cfg,
+				struct vpbe_config *vpbe_cfg)
+{
+	if (vpfe_cfg || vpbe_cfg)
+		platform_device_register(&dm365_vpss_device);
+
+	if (vpfe_cfg) {
+		vpfe_capture_dev.dev.platform_data = vpfe_cfg;
+		/* Add isif clock alias */
+		clk_add_alias("master", dm365_isif_dev.name,
+			      "vpss_master", NULL);
+		platform_device_register(&dm365_isif_dev);
+		platform_device_register(&vpfe_capture_dev);
+	}
+	if (vpbe_cfg) {
+		dm365_vpbe_dev.dev.platform_data = vpbe_cfg;
+		platform_device_register(&dm365_osd_dev);
+		platform_device_register(&dm365_venc_dev);
+		platform_device_register(&dm365_vpbe_dev);
+		platform_device_register(&dm365_vpbe_display);
+	}
+
+	return 0;
+}
+
 static int __init dm365_init_devices(void)
 {
 	if (!cpu_is_davinci_dm365())
@@ -1245,16 +1436,6 @@ static int __init dm365_init_devices(void)
 	clk_add_alias(NULL, dev_name(&dm365_mdio_device.dev),
 		      NULL, &dm365_emac_device.dev);
 
-	/* Add isif clock alias */
-	clk_add_alias("master", dm365_isif_dev.name, "vpss_master", NULL);
-	platform_device_register(&dm365_vpss_device);
-	platform_device_register(&dm365_isif_dev);
-	platform_device_register(&vpfe_capture_dev);
 	return 0;
 }
 postcore_initcall(dm365_init_devices);
-
-void dm365_set_vpfe_config(struct vpfe_config *cfg)
-{
-       vpfe_capture_dev.dev.platform_data = cfg;
-}
-- 
1.7.4.1

[PATCH v5 1/2] ARM: davinci: dm365: add support for v4l2 video display

[Sekhar Nori]

On 12/3/2012 1:51 PM, Prabhakar Lad wrote:
> From: Manjunath Hadli <manjunath.hadli@ti.com>
> 
> Create platform devices for various video modules like venc,osd,
> vpbe and v4l2 driver for dm365.
> 
> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
> ---
>  arch/arm/mach-davinci/board-dm365-evm.c |    4 +-
>  arch/arm/mach-davinci/davinci.h         |    2 +-
>  arch/arm/mach-davinci/dm365.c           |  203 +++++++++++++++++++++++++++++--
>  3 files changed, 195 insertions(+), 14 deletions(-)
> 
> diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
> index 1b4a8ad..0c3dae6 100644
> --- a/arch/arm/mach-davinci/board-dm365-evm.c
> +++ b/arch/arm/mach-davinci/board-dm365-evm.c
> @@ -564,8 +564,6 @@ static struct davinci_uart_config uart_config __initdata = {
>  
>  static void __init dm365_evm_map_io(void)
>  {
> -	/* setup input configuration for VPFE input devices */
> -	dm365_set_vpfe_config(&vpfe_cfg);
>  	dm365_init();
>  }
>  
> @@ -597,6 +595,8 @@ static __init void dm365_evm_init(void)
>  
>  	davinci_setup_mmc(0, &dm365evm_mmc_config);
>  
> +	dm365_init_video(&vpfe_cfg, NULL);
> +
>  	/* maybe setup mmc1/etc ... _after_ mmc0 */
>  	evm_init_cpld();
>  
> diff --git a/arch/arm/mach-davinci/davinci.h b/arch/arm/mach-davinci/davinci.h
> index 12d544b..1c2670f 100644
> --- a/arch/arm/mach-davinci/davinci.h
> +++ b/arch/arm/mach-davinci/davinci.h
> @@ -84,7 +84,7 @@ void __init dm365_init_ks(struct davinci_ks_platform_data *pdata);
>  void __init dm365_init_rtc(void);
>  void dm365_init_spi0(unsigned chipselect_mask,
>  			const struct spi_board_info *info, unsigned len);
> -void dm365_set_vpfe_config(struct vpfe_config *cfg);
> +int __init dm365_init_video(struct vpfe_config *, struct vpbe_config *);
>  
>  /* DM644x function declarations */
>  void __init dm644x_init(void);
> diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c
> index b680c83..cada153 100644
> --- a/arch/arm/mach-davinci/dm365.c
> +++ b/arch/arm/mach-davinci/dm365.c
> @@ -40,10 +40,16 @@
>  
>  #define DM365_REF_FREQ		24000000	/* 24 MHz on the DM365 EVM */
>  
> +#define DM3XX_VDAC_CONFIG		0x01c4002c
> +
> +#define DM365_RTC_BASE			0x01c69000
> +
>  /* Base of key scan register bank */
>  #define DM365_KEYSCAN_BASE		0x01c69400
>  
> -#define DM365_RTC_BASE			0x01c69000
> +#define DM365_OSD_REG_BASE		0x01c71c00

Nit: Can you call it DM365_OSD_BASE. If we were to include REG in the
name, then it should be done consistently. So we would instead have
DM365_KEYSCAN_REG_BASE.

> +
> +#define DM365_VENC_REG_BASE		0x01c71e00
>  
>  #define DAVINCI_DM365_VC_BASE		0x01d0c000
>  #define DAVINCI_DMA_VC_TX		2
> @@ -56,6 +62,11 @@
>  #define DM365_EMAC_CNTRL_RAM_OFFSET	0x1000
>  #define DM365_EMAC_CNTRL_RAM_SIZE	0x2000
>  
> +#define DM365_VPSS_CLK_CTRL_ADDR		0x44
> +#define DM365_VPSS_VENCCLKEN_ENABLE		BIT(3)
> +#define DM365_VPSS_DACCLKEN_ENABLE		BIT(4)
> +#define DM365_VPSS_PLLC2SYSCLK5_ENABLE		(BIT(5) & ~BIT(6))

This expression does not make much sense. It is same as BIT(5). You
needed a mask and an enable?

> +
>  static struct pll_data pll1_data = {
>  	.num		= 1,
>  	.phys_base	= DAVINCI_PLL1_BASE,
> @@ -1232,6 +1243,186 @@ static struct platform_device dm365_isif_dev = {
>  	},
>  };
>  
> +static struct resource dm365_osd_resources[] = {
> +	{
> +		.start = DM365_OSD_REG_BASE,
> +		.end   = DM365_OSD_REG_BASE + 0x100,

	.end   = DM365_OSD_REG_BASE + 0xff,

A similar fix is needed multiple places below. Sorry, I did not notice
this last time around.

Thanks,
Sekhar

[PATCH v5 1/2] ARM: davinci: dm365: add support for v4l2 video display

[Prabhakar Lad]

Sekhar,

Thanks for the review.

On Tue, Dec 4, 2012 at 6:44 PM, Sekhar Nori <nsekhar@ti.com> wrote:
> On 12/3/2012 1:51 PM, Prabhakar Lad wrote:
>> From: Manjunath Hadli <manjunath.hadli@ti.com>
>>
>> Create platform devices for various video modules like venc,osd,
>> vpbe and v4l2 driver for dm365.
>>
>> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
>> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
>> ---
>>  arch/arm/mach-davinci/board-dm365-evm.c |    4 +-
>>  arch/arm/mach-davinci/davinci.h         |    2 +-
>>  arch/arm/mach-davinci/dm365.c           |  203 +++++++++++++++++++++++++++++--
>>  3 files changed, 195 insertions(+), 14 deletions(-)
>>
>> diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
>> index 1b4a8ad..0c3dae6 100644
>> --- a/arch/arm/mach-davinci/board-dm365-evm.c
>> +++ b/arch/arm/mach-davinci/board-dm365-evm.c
>> @@ -564,8 +564,6 @@ static struct davinci_uart_config uart_config __initdata = {
>>
>>  static void __init dm365_evm_map_io(void)
>>  {
>> -     /* setup input configuration for VPFE input devices */
>> -     dm365_set_vpfe_config(&vpfe_cfg);
>>       dm365_init();
>>  }
>>
>> @@ -597,6 +595,8 @@ static __init void dm365_evm_init(void)
>>
>>       davinci_setup_mmc(0, &dm365evm_mmc_config);
>>
>> +     dm365_init_video(&vpfe_cfg, NULL);
>> +
>>       /* maybe setup mmc1/etc ... _after_ mmc0 */
>>       evm_init_cpld();
>>
>> diff --git a/arch/arm/mach-davinci/davinci.h b/arch/arm/mach-davinci/davinci.h
>> index 12d544b..1c2670f 100644
>> --- a/arch/arm/mach-davinci/davinci.h
>> +++ b/arch/arm/mach-davinci/davinci.h
>> @@ -84,7 +84,7 @@ void __init dm365_init_ks(struct davinci_ks_platform_data *pdata);
>>  void __init dm365_init_rtc(void);
>>  void dm365_init_spi0(unsigned chipselect_mask,
>>                       const struct spi_board_info *info, unsigned len);
>> -void dm365_set_vpfe_config(struct vpfe_config *cfg);
>> +int __init dm365_init_video(struct vpfe_config *, struct vpbe_config *);
>>
>>  /* DM644x function declarations */
>>  void __init dm644x_init(void);
>> diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c
>> index b680c83..cada153 100644
>> --- a/arch/arm/mach-davinci/dm365.c
>> +++ b/arch/arm/mach-davinci/dm365.c
>> @@ -40,10 +40,16 @@
>>
>>  #define DM365_REF_FREQ               24000000        /* 24 MHz on the DM365 EVM */
>>
>> +#define DM3XX_VDAC_CONFIG            0x01c4002c
>> +
>> +#define DM365_RTC_BASE                       0x01c69000
>> +
>>  /* Base of key scan register bank */
>>  #define DM365_KEYSCAN_BASE           0x01c69400
>>
>> -#define DM365_RTC_BASE                       0x01c69000
>> +#define DM365_OSD_REG_BASE           0x01c71c00
>
> Nit: Can you call it DM365_OSD_BASE. If we were to include REG in the
> name, then it should be done consistently. So we would instead have
> DM365_KEYSCAN_REG_BASE.
>
Ok.

>> +
>> +#define DM365_VENC_REG_BASE          0x01c71e00
>>
>>  #define DAVINCI_DM365_VC_BASE                0x01d0c000
>>  #define DAVINCI_DMA_VC_TX            2
>> @@ -56,6 +62,11 @@
>>  #define DM365_EMAC_CNTRL_RAM_OFFSET  0x1000
>>  #define DM365_EMAC_CNTRL_RAM_SIZE    0x2000
>>
>> +#define DM365_VPSS_CLK_CTRL_ADDR             0x44
>> +#define DM365_VPSS_VENCCLKEN_ENABLE          BIT(3)
>> +#define DM365_VPSS_DACCLKEN_ENABLE           BIT(4)
>> +#define DM365_VPSS_PLLC2SYSCLK5_ENABLE               (BIT(5) & ~BIT(6))
>
> This expression does not make much sense. It is same as BIT(5). You
> needed a mask and an enable?
>
Agreed its equivalent to BIT(5), but pll2c2sysclk5 depends on two bits
bit 5 and bit bit 6, so to keep consistent I used them. Do you want me to remove
it and just keep BIT(5) ?

>> +
>>  static struct pll_data pll1_data = {
>>       .num            = 1,
>>       .phys_base      = DAVINCI_PLL1_BASE,
>> @@ -1232,6 +1243,186 @@ static struct platform_device dm365_isif_dev = {
>>       },
>>  };
>>
>> +static struct resource dm365_osd_resources[] = {
>> +     {
>> +             .start = DM365_OSD_REG_BASE,
>> +             .end   = DM365_OSD_REG_BASE + 0x100,
>
>         .end   = DM365_OSD_REG_BASE + 0xff,
>
> A similar fix is needed multiple places below. Sorry, I did not notice
> this last time around.
>
Ok I'll fix it.

Thanks and Regards,
--Prabhakar Lad

> Thanks,
> Sekhar

[PATCH v5 2/2] ARM: davinci: dm365 EVM: add support for VPBE display

[Prabhakar Lad]

From: Manjunath Hadli <manjunath.hadli@ti.com>

add support for V4L2 video display to DM365 EVM.
Support for SD and ED modes is provided, along with Composite
and Component outputs.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
---
 arch/arm/mach-davinci/board-dm365-evm.c |  177 ++++++++++++++++++++++++++++++-
 1 files changed, 176 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
index 0c3dae6..10f2a85 100644
--- a/arch/arm/mach-davinci/board-dm365-evm.c
+++ b/arch/arm/mach-davinci/board-dm365-evm.c
@@ -27,6 +27,7 @@
 #include <linux/input.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/eeprom.h>
+#include <linux/v4l2-dv-timings.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -374,6 +375,180 @@ static struct vpfe_config vpfe_cfg = {
 	.ccdc = "ISIF",
 };
 
+/* venc standards timings */
+static struct vpbe_enc_mode_info dm365evm_enc_std_timing[] = {
+	{
+		.name		= "ntsc",
+		.timings_type	= VPBE_ENC_STD,
+		.std_id		= V4L2_STD_525_60,
+		.interlaced	= 1,
+		.xres		= 720,
+		.yres		= 480,
+		.aspect		= {11, 10},
+		.fps		= {30000, 1001},
+		.left_margin	= 0x79,
+		.right_margin	= 0,
+		.upper_margin	= 0x10,
+		.lower_margin	= 0,
+		.hsync_len	= 0,
+		.vsync_len	= 0,
+		.flags		= 0,
+	},
+	{
+		.name		= "pal",
+		.timings_type	= VPBE_ENC_STD,
+		.std_id		= V4L2_STD_625_50,
+		.interlaced	= 1,
+		.xres		= 720,
+		.yres		= 576,
+		.aspect		= {54, 59},
+		.fps		= {25, 1},
+		.left_margin	= 0x7E,
+		.right_margin	= 0,
+		.upper_margin	= 0x16,
+		.lower_margin	= 0,
+		.hsync_len	= 0,
+		.vsync_len	= 0,
+		.flags		= 0,
+	},
+};
+
+/* venc dv timings */
+static struct vpbe_enc_mode_info dm365evm_enc_preset_timing[] = {
+	{
+		.name		= "480p59_94",
+		.timings_type	= VPBE_ENC_CUSTOM_TIMINGS,
+		.dv_timings	= V4L2_DV_BT_CEA_720X480P59_94,
+		.interlaced	= 0,
+		.xres		= 720,
+		.yres		= 480,
+		.aspect		= {1, 1},
+		.fps		= {5994, 100},
+		.left_margin	= 0x8F,
+		.right_margin	= 0,
+		.upper_margin	= 0x2D,
+		.lower_margin	= 0,
+		.hsync_len	= 0,
+		.vsync_len	= 0,
+		.flags		= 0,
+	},
+	{
+		.name		= "576p50",
+		.timings_type	= VPBE_ENC_CUSTOM_TIMINGS,
+		.dv_timings	= V4L2_DV_BT_CEA_720X576P50,
+		.interlaced	= 0,
+		.xres		= 720,
+		.yres		= 576,
+		.aspect		= {1, 1},
+		.fps		= {50, 1},
+		.left_margin	= 0x8C,
+		.right_margin	= 0,
+		.upper_margin	= 0x36,
+		.lower_margin	= 0,
+		.hsync_len	= 0,
+		.vsync_len	= 0,
+		.flags		= 0,
+	},
+	{
+		.name		= "720p60",
+		.timings_type	= VPBE_ENC_CUSTOM_TIMINGS,
+		.dv_timings	= V4L2_DV_BT_CEA_1280X720P60,
+		.interlaced	= 0,
+		.xres		= 1280,
+		.yres		= 720,
+		.aspect		= {1, 1},
+		.fps		= {60, 1},
+		.left_margin	= 0x117,
+		.right_margin	= 70,
+		.upper_margin	= 38,
+		.lower_margin	= 3,
+		.hsync_len	= 80,
+		.vsync_len	= 5,
+		.flags		= 0,
+	},
+	{
+		.name		= "1080i60",
+		.timings_type	= VPBE_ENC_CUSTOM_TIMINGS,
+		.dv_timings	= V4L2_DV_BT_CEA_1920X1080I60,
+		.interlaced	= 1,
+		.xres		= 1920,
+		.yres		= 1080,
+		.aspect		= {1, 1},
+		.fps		= {30, 1},
+		.left_margin	= 0xc9,
+		.right_margin	= 80,
+		.upper_margin	= 30,
+		.lower_margin	= 3,
+		.hsync_len	= 88,
+		.vsync_len	= 5,
+		.flags		= 0,
+	},
+};
+
+#define VENC_STD_ALL	(V4L2_STD_NTSC | V4L2_STD_PAL)
+
+/*
+ * The outputs available from VPBE + ecnoders. Keep the
+ * the order same as that of encoders. First those from venc followed by that
+ * from encoders. Index in the output refers to index on a particular
+ * encoder.Driver uses this index to pass it to encoder when it supports more
+ * than one output. Application uses index of the array to set an output.
+ */
+static struct vpbe_output dm365evm_vpbe_outputs[] = {
+	{
+		.output		= {
+			.index		= 0,
+			.name		= "Composite",
+			.type		= V4L2_OUTPUT_TYPE_ANALOG,
+			.std		= VENC_STD_ALL,
+			.capabilities	= V4L2_OUT_CAP_STD,
+		},
+		.subdev_name	= DM365_VPBE_VENC_SUBDEV_NAME,
+		.default_mode	= "ntsc",
+		.num_modes	= ARRAY_SIZE(dm365evm_enc_std_timing),
+		.modes		= dm365evm_enc_std_timing,
+		.if_params	= V4L2_MBUS_FMT_FIXED,
+	},
+	{
+		.output		= {
+			.index		= 1,
+			.name		= "Component",
+			.type		= V4L2_OUTPUT_TYPE_ANALOG,
+			.capabilities	= V4L2_OUT_CAP_DV_TIMINGS,
+		},
+		.subdev_name	= DM365_VPBE_VENC_SUBDEV_NAME,
+		.default_mode	= "480p59_94",
+		.num_modes	= ARRAY_SIZE(dm365evm_enc_preset_timing),
+		.modes		= dm365evm_enc_preset_timing,
+		.if_params	= V4L2_MBUS_FMT_FIXED,
+	},
+};
+
+/*
+ * Amplifiers on the board
+ */
+static struct amp_config_info vpbe_amp = {
+	.module_name	= "ths7303",
+	.is_i2c		= 1,
+	.board_info	= {
+		I2C_BOARD_INFO("ths7303", 0x2c)
+	}
+};
+
+static struct vpbe_config dm365evm_display_cfg = {
+	.module_name	= "dm365-vpbe-display",
+	.i2c_adapter_id	= 1,
+	.amp		= &vpbe_amp,
+	.osd		= {
+		.module_name	= DM365_VPBE_OSD_SUBDEV_NAME,
+	},
+	.venc		= {
+		.module_name	= DM365_VPBE_VENC_SUBDEV_NAME,
+	},
+	.num_outputs	= ARRAY_SIZE(dm365evm_vpbe_outputs),
+	.outputs	= dm365evm_vpbe_outputs,
+};
+
 static void __init evm_init_i2c(void)
 {
 	davinci_init_i2c(&i2c_pdata);
@@ -595,7 +770,7 @@ static __init void dm365_evm_init(void)
 
 	davinci_setup_mmc(0, &dm365evm_mmc_config);
 
-	dm365_init_video(&vpfe_cfg, NULL);
+	dm365_init_video(&vpfe_cfg, &dm365evm_display_cfg);
 
 	/* maybe setup mmc1/etc ... _after_ mmc0 */
 	evm_init_cpld();
-- 
1.7.4.1

[PATCH v5 2/2] ARM: davinci: dm365 EVM: add support for VPBE display

[Sekhar Nori]

On 12/3/2012 1:51 PM, Prabhakar Lad wrote:
> From: Manjunath Hadli <manjunath.hadli@ti.com>
> 
> add support for V4L2 video display to DM365 EVM.
> Support for SD and ED modes is provided, along with Composite
> and Component outputs.
> 
> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
> ---
>  arch/arm/mach-davinci/board-dm365-evm.c |  177 ++++++++++++++++++++++++++++++-
>  1 files changed, 176 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
> index 0c3dae6..10f2a85 100644
> --- a/arch/arm/mach-davinci/board-dm365-evm.c
> +++ b/arch/arm/mach-davinci/board-dm365-evm.c
> @@ -27,6 +27,7 @@
>  #include <linux/input.h>
>  #include <linux/spi/spi.h>
>  #include <linux/spi/eeprom.h>
> +#include <linux/v4l2-dv-timings.h>
>  
>  #include <asm/mach-types.h>
>  #include <asm/mach/arch.h>
> @@ -374,6 +375,180 @@ static struct vpfe_config vpfe_cfg = {
>  	.ccdc = "ISIF",
>  };
>  
> +/* venc standards timings */
> +static struct vpbe_enc_mode_info dm365evm_enc_std_timing[] = {
> +	{
> +		.name		= "ntsc",
> +		.timings_type	= VPBE_ENC_STD,
> +		.std_id		= V4L2_STD_525_60,
> +		.interlaced	= 1,
> +		.xres		= 720,
> +		.yres		= 480,
> +		.aspect		= {11, 10},
> +		.fps		= {30000, 1001},
> +		.left_margin	= 0x79,
> +		.right_margin	= 0,
> +		.upper_margin	= 0x10,
> +		.lower_margin	= 0,
> +		.hsync_len	= 0,
> +		.vsync_len	= 0,
> +		.flags		= 0,

I wonder what makes this entire information board specific? Shouldn't
these (or at least most of these) be same across all devices which
support NTSC and hence should be coming from some common code instead of
being replicated for each platform that supports NTSC?

Thanks,
Sekhar

[PATCH v5 2/2] ARM: davinci: dm365 EVM: add support for VPBE display

[Prabhakar Lad]

Hi Sekhar,

On Tue, Dec 4, 2012 at 6:52 PM, Sekhar Nori <nsekhar@ti.com> wrote:
> On 12/3/2012 1:51 PM, Prabhakar Lad wrote:
>> From: Manjunath Hadli <manjunath.hadli@ti.com>
>>
>> add support for V4L2 video display to DM365 EVM.
>> Support for SD and ED modes is provided, along with Composite
>> and Component outputs.
>>
>> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
>> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
>> ---
>>  arch/arm/mach-davinci/board-dm365-evm.c |  177 ++++++++++++++++++++++++++++++-
>>  1 files changed, 176 insertions(+), 1 deletions(-)
>>
>> diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
>> index 0c3dae6..10f2a85 100644
>> --- a/arch/arm/mach-davinci/board-dm365-evm.c
>> +++ b/arch/arm/mach-davinci/board-dm365-evm.c
>> @@ -27,6 +27,7 @@
>>  #include <linux/input.h>
>>  #include <linux/spi/spi.h>
>>  #include <linux/spi/eeprom.h>
>> +#include <linux/v4l2-dv-timings.h>
>>
>>  #include <asm/mach-types.h>
>>  #include <asm/mach/arch.h>
>> @@ -374,6 +375,180 @@ static struct vpfe_config vpfe_cfg = {
>>       .ccdc = "ISIF",
>>  };
>>
>> +/* venc standards timings */
>> +static struct vpbe_enc_mode_info dm365evm_enc_std_timing[] = {
>> +     {
>> +             .name           = "ntsc",
>> +             .timings_type   = VPBE_ENC_STD,
>> +             .std_id         = V4L2_STD_525_60,
>> +             .interlaced     = 1,
>> +             .xres           = 720,
>> +             .yres           = 480,
>> +             .aspect         = {11, 10},
>> +             .fps            = {30000, 1001},
>> +             .left_margin    = 0x79,
>> +             .right_margin   = 0,
>> +             .upper_margin   = 0x10,
>> +             .lower_margin   = 0,
>> +             .hsync_len      = 0,
>> +             .vsync_len      = 0,
>> +             .flags          = 0,
>
> I wonder what makes this entire information board specific? Shouldn't
> these (or at least most of these) be same across all devices which
> support NTSC and hence should be coming from some common code instead of
> being replicated for each platform that supports NTSC?
>
most of the structure members are board specific,

	struct v4l2_fract aspect;
	struct v4l2_fract fps;
	unsigned int left_margin;
	unsigned int right_margin;
	unsigned int upper_margin;
	unsigned int lower_margin;
	unsigned int hsync_len;
	unsigned int vsync_len;
	unsigned int flags;

And as of now there is no ready made structure within v4l2 which
provides the common data. So I'll be keeping this as it is.

Regards,
--Prabhakar

> Thanks,
> Sekhar

[PATCH v5 2/2] ARM: davinci: dm365 EVM: add support for VPBE display

[Sekhar Nori]

On 3/14/2013 2:09 PM, Prabhakar Lad wrote:
> Hi Sekhar,
> 
> On Tue, Dec 4, 2012 at 6:52 PM, Sekhar Nori <nsekhar@ti.com> wrote:
>> On 12/3/2012 1:51 PM, Prabhakar Lad wrote:
>>> From: Manjunath Hadli <manjunath.hadli@ti.com>
>>>
>>> add support for V4L2 video display to DM365 EVM.
>>> Support for SD and ED modes is provided, along with Composite
>>> and Component outputs.
>>>
>>> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
>>> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
>>> ---
>>>  arch/arm/mach-davinci/board-dm365-evm.c |  177 ++++++++++++++++++++++++++++++-
>>>  1 files changed, 176 insertions(+), 1 deletions(-)
>>>
>>> diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
>>> index 0c3dae6..10f2a85 100644
>>> --- a/arch/arm/mach-davinci/board-dm365-evm.c
>>> +++ b/arch/arm/mach-davinci/board-dm365-evm.c
>>> @@ -27,6 +27,7 @@
>>>  #include <linux/input.h>
>>>  #include <linux/spi/spi.h>
>>>  #include <linux/spi/eeprom.h>
>>> +#include <linux/v4l2-dv-timings.h>
>>>
>>>  #include <asm/mach-types.h>
>>>  #include <asm/mach/arch.h>
>>> @@ -374,6 +375,180 @@ static struct vpfe_config vpfe_cfg = {
>>>       .ccdc = "ISIF",
>>>  };
>>>
>>> +/* venc standards timings */
>>> +static struct vpbe_enc_mode_info dm365evm_enc_std_timing[] = {
>>> +     {
>>> +             .name           = "ntsc",
>>> +             .timings_type   = VPBE_ENC_STD,
>>> +             .std_id         = V4L2_STD_525_60,
>>> +             .interlaced     = 1,
>>> +             .xres           = 720,
>>> +             .yres           = 480,
>>> +             .aspect         = {11, 10},
>>> +             .fps            = {30000, 1001},
>>> +             .left_margin    = 0x79,
>>> +             .right_margin   = 0,
>>> +             .upper_margin   = 0x10,
>>> +             .lower_margin   = 0,
>>> +             .hsync_len      = 0,
>>> +             .vsync_len      = 0,
>>> +             .flags          = 0,
>>
>> I wonder what makes this entire information board specific? Shouldn't
>> these (or at least most of these) be same across all devices which
>> support NTSC and hence should be coming from some common code instead of
>> being replicated for each platform that supports NTSC?
>>
> most of the structure members are board specific,
> 
> 	struct v4l2_fract aspect;
> 	struct v4l2_fract fps;
> 	unsigned int left_margin;
> 	unsigned int right_margin;
> 	unsigned int upper_margin;
> 	unsigned int lower_margin;
> 	unsigned int hsync_len;
> 	unsigned int vsync_len;
> 	unsigned int flags;
> 
> And as of now there is no ready made structure within v4l2 which
> provides the common data. So I'll be keeping this as it is.

I am fine with this approach.

Regards,
Sekhar